Microchip Technology

SY89430VJC - 950 MHz Clock Synthesizer | Microchip

Teilenummer: SY89430VJC ✓ Aktiv
5 V or 3.3 V Vdss 28-pin PLCC (J-lead) Package 50 MHz to 950 MHz Speed
MOQ: 1 |

SY89430VJC Übersicht

The Microchip Technology SY89430VJC is a programmable frequency synthesizer covering 50 MHz to 950 MHz, with 5 V and 3.3 V supply options and differential PECL outputs in a 28-pin PLCC J-lead package. It is designed for clock and timing systems requiring low output jitter and flexible frequency programming.

A frequency synthesizer generates or distributes a stable clock derived from a controllable reference source. Within clock and timing electronics, the SY89430VJC belongs to the PLL and clock-generator hierarchy and supports serialized or parallel configuration, allowing it to serve as the timing backbone for communications, instrumentation, industrial control, and test systems.

Key features include a synthesized architecture, minimal frequency over-shoot, a 3-wire serial interface, a parallel interface for power-on configuration, and an internal quartz reference. Differential PECL outputs provide a maximum frequency of 950 MHz, while the specified peak-to-peak output jitter is no more than 25 ps. These characteristics support high-speed clocking requirements where timing margin and reference stability are important.

The device accepts either 5 V or 3.3 V operation, depending on the selected configuration, and its broad tuning range allows one clock architecture to cover multiple system frequencies. The serial interface captures programmed values when the load signal changes state, making it practical for controlled test and measurement setups. A parallel power-on interface offers an alternative configuration path when the required divider and frequency settings are fixed in the system.

Typical uses include laboratory clock sources, communications equipment, semiconductor test systems, frequency-generation instrumentation, and industrial data-acquisition platforms. The differential PECL interface is particularly appropriate for circuits designed around high-speed ECL-compatible clocking, although downstream logic compatibility must be confirmed against voltage and termination requirements.

Layout should preserve short, controlled-impedance clock paths and keep the reference, power, and decoupling connections close to the device. Differential routing must maintain consistent spacing and termination, and unused clock outputs should be handled according to the manufacturer datasheet. Adequate bypass capacitance and a clean reference path help preserve low jitter and avoid unexpected overshoot during frequency transitions.

This page combines the programming features, package information, clocking characteristics, application guidance, and engineering considerations needed to evaluate the SY89430VJC. It also distinguishes the verified device capabilities from unverified details, helping engineers move from component selection to a correctly implemented 950 MHz clock source.

Drop-in-Alternativen für SY89430VJC – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

SY89430VJC Technische Daten

Device Type Programmable frequency synthesizer
Frequency Range 50 MHz to 950 MHz
Maximum Output Frequency 950 MHz
Supply Voltage Options 5 V or 3.3 V
Ausgangstyp Differential PECL
Peak-to-Peak Output Jitter 25 ps maximum
Architecture Synthesized
Serial Control Interface 3-wire serial interface
Parallel Configuration Parallel interface for power-on
Internal Reference Internal quartz reference
Nominal Reference Frequency 25 MHz
Frequency Transition Behavior Minimal frequency over-shoot
Gehäuse 28-pin PLCC (J-lead)
Montageart Surface mount

SY89430VJC 28-pin plcc (j-lead) Pinbelegungsleitfaden

Pinbelegung für SY89430VJC (28-pin plcc (j-lead)-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.

Pinbelegungsdiagramm für SY89430VJC im 28-pin plcc (j-lead)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für SY89430VJC.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

SY89430VJC ist geeignet für 6 Anwendungs: Communications Clock Generation, Semiconductor Test Systems, Frequency Generation Instrumentation, Industrial Data Acquisition, High-Speed Interface Timing, RF and Microwave Test Systems.

🌐

Communications Clock Generation

The SY89430VJC fits communications systems requiring a programmable differential clock across a broad frequency range. Its synthesized architecture covers 50 MHz to 950 MHz, while the 25 ps maximum peak-to-peak output jitter helps preserve timing margin in high-speed data paths. The 3-wire serial interface permits runtime frequency changes, and the parallel power-on interface supports fixed configurations. Designers should verify that downstream receivers accept PECL levels and use termination matched to the board impedance.

🖥️

Semiconductor Test Systems

The SY89430VJC can provide programmable clock stimulus for semiconductor test systems operating up to 950 MHz. Its minimal frequency over-shoot is useful when reducing timing excursions during programmed frequency changes, while the low 25 ps peak-to-peak jitter specification supports high-speed edge-sensitive measurements. The serial programming path allows a test sequencer to select operating conditions, and the parallel path provides deterministic power-on settings. Calibration and reference quality remain part of the total measurement uncertainty.

📡

Frequency Generation Instrumentation

The SY89430VJC is appropriate for laboratory frequency-generation instruments that need a selectable differential clock source. Its wide 50 MHz to 950 MHz operating range covers multiple test frequencies without changing the synthesizer architecture. The synthesized internal reference, serial programming, and parallel power-on configuration provide flexible setup workflows for automated or fixed-condition instruments. Output amplitude, common-mode voltage, termination, and channel matching must be checked against the instrument’s downstream clock receiver.

🏭

Industrial Data Acquisition

The SY89430VJC can supply a stable, programmable clock to industrial acquisition and control electronics. The synthesized reference reduces dependence on multiple discrete frequency sources, while the serial interface supports configuration from a controller and the parallel interface supports fixed startup conditions. Differential PECL outputs are suited to systems designed for controlled-impedance clock distribution. Engineers should evaluate clock jitter against the acquisition timing budget and separate sensitive clock routing from high-current switching nodes.

🔧

High-Speed Interface Timing

The SY89430VJC is suitable for generating clocks for high-speed interfaces when the system requires up to 950 MHz operation and tightly controlled output jitter. Differential PECL outputs can reduce sensitivity to common-mode noise when implemented with controlled-impedance routing and correct termination. The programmable synthesized architecture allows one source to cover several interface rates. Before implementation, confirm the receiver’s voltage thresholds, edge-rate requirements, maximum tolerable jitter, and the effect of PCB loss on the selected clock frequency.

📶

RF and Microwave Test Systems

The SY89430VJC can serve as a local reference-clock source in RF and microwave test systems requiring programmable frequencies up to 950 MHz. Its synthesized architecture supports repeatable clock generation, and the 25 ps maximum peak-to-peak jitter specification is valuable when clock quality contributes to phase noise or conversion accuracy. The differential PECL interface supports controlled clock distribution to RF test modules. System designers must verify module input capacitance, termination requirements, and the total reference contribution to measurement performance.

Zusammenfassung der empfohlenen Produkte

SY89430VJZ Related 28-LCC frequency-synthesizer ordering variant Verwendet in: Communications Clock Generation, Semiconductor Test Systems, Industrial Data Acquisition, High-Speed Interface Timing, RF and Microwave Test Systems SY89430VJC-TR Tape-and-reel ordering form of the target device Verwendet in: Communications Clock Generation, Semiconductor Test Systems, Frequency Generation Instrumentation, Industrial Data Acquisition, RF and Microwave Test Systems SY89430VJC Microchip Technology Verwendet in: Frequency Generation Instrumentation, High-Speed Interface Timing
What is the SY89430VJC frequency synthesizer?
The SY89430VJC is a Microchip Technology programmable frequency synthesizer that operates from 50 MHz to 950 MHz and produces differential PECL clock outputs. According to the manufacturer datasheet, it supports 5 V and 3.3 V supply configurations, a synthesized architecture, a 3-wire serial programming interface, and a parallel power-on interface in a 28-pin PLCC J-lead package.
What is the maximum frequency of the SY89430VJC?
The maximum output frequency of the SY89430VJC is 950 MHz. The manufacturer datasheet identifies the device as a 50 MHz to 950 MHz programmable synthesizer with differential PECL outputs. This frequency range supports high-speed communications, instrumentation, semiconductor test, and industrial timing applications that require a programmable clock source.
What supply voltage does the SY89430VJC support?
The SY89430VJC supports both 5 V and 3.3 V power-supply options. According to the manufacturer datasheet feature summary, the supply configuration is selectable, allowing the synthesizer to fit systems designed around either voltage level. Confirm the configuration registers and output-amplitude requirements for the specific device variant before finalizing the board power design.
What is the output jitter of the SY89430VJC?
The SY89430VJC differential PECL output jitter is specified at no more than 25 ps peak-to-peak. The manufacturer datasheet lists this value as a principal feature of the synthesizer. Low output jitter is important when the generated clock establishes the timing margin of high-speed data paths, converters, test channels, or communication interfaces.
How is the SY89430VJC programmed?
The SY89430VJC can be programmed through its 3-wire serial interface or through a parallel interface for power-on configuration. According to the manufacturer datasheet, serial data is captured into the configuration latch register on the required S_LOAD edge. The serial method supports dynamic setup, while the parallel method is useful when the clock settings are fixed.
Where can I download the SY89430VJC datasheet PDF?
The SY89430VJC manufacturer datasheet is available through the PDF link listed on this product page, and the document describes it as a 5 V or 3.3 V programmable frequency synthesizer. Use the pin-description, AC timing, and configuration-register sections when assigning connections and programming the 28-pin device. The pinout diagram on this page should not be used as a substitute for those tables.
Where can I find the SY89430VJC pinout?
The complete SY89430VJC pin assignments are found in the manufacturer datasheet rather than in the distributor catalog excerpts. The device is identified as a 28-pin PLCC with J-leads, and its pins include power, ground, reference, programming, and differential clock connections. Assign PCB nets from the datasheet pin-description table and preserve the package orientation specified by the manufacturer.
Where can I buy the SY89430VJC?
The SY89430VJC can be requested through the Request a Quote form on this page. The form lets an engineer specify the required quantity, package marking, shipment destination, and production schedule before committing to an order. This route is also appropriate when the required delivery timing, traceability, or inspection documentation must be confirmed.
What is the price of the SY89430VJC?
The current commercial terms for the SY89430VJC are shown through the Request a Quote form on this page. Submit the required quantity and any date-code, packaging, or inspection requirements so the offer can reflect the exact order configuration. The form is the appropriate channel for obtaining a current quote without relying on a static catalog price.
What is the lead time for the SY89430VJC?
The current lead time and available production allocation should be requested through the Request a Quote form on this page. Include your required quantity, target delivery date, and approved vendor list so the order response can address scheduling constraints. For production planning, treat the confirmed allocation date rather than a general catalog estimate as the controlling date.
Is the SY89430VJC in stock?
Current inventory status for the exact SY89430VJC order configuration is confirmed through the Request a Quote form on this page. A stock quantity shown by a catalog listing may not account for the quantity, date code, or shipping destination required by a particular build. State those requirements in the quote request to obtain an allocation that matches the production schedule.
What is the difference between the SY89430VJC and SY89430VJZ?
The SY89430VJC and SY89430VJZ are listed as 28-LCC J-lead frequency-synthesizer variants, but the available catalog information does not establish that they are pin-to-pin drop-in equivalents. According to the manufacturer datasheet naming convention, the package and suffix details must be compared before substitution. Verify the exact temperature, lead-free, tape-and-reel, and ordering attributes before treating one MPN as a replacement for the other.
Can the SY89430VJZ replace the SY89430VJC?
The SY89430VJZ should not be treated as a drop-in replacement for the SY89430VJC without a complete manufacturer comparison. Both listings identify a 28-LCC J-lead package, but package similarity alone does not prove identical pin functions, electrical ratings, or ordering attributes. Consult the manufacturer datasheet and ordering information, then confirm every board-level connection and operating condition.
What can replace the SY89430VJC?
No independently verified drop-in replacement for the SY89430VJC is established here. The search results did not identify a cross-brand device with a proven 28-pin PLCC footprint, identical programming interface, differential PECL outputs, and compatible frequency range. A valid replacement must therefore match the pinout, supply requirements, reference frequency, output logic levels, jitter target, and configuration method before it is approved for a PCB revision.
Is the SY89430VJC suitable for communications and test equipment?
The SY89430VJC is suitable for communications and test equipment that needs a programmable clock up to 950 MHz with low output jitter. Its differential PECL outputs, 25 ps maximum peak-to-peak jitter, 3-wire serial programming, and synthesized architecture support controlled clock generation. The surrounding receiver must support compatible ECL levels and termination, and the reference source must meet the jitter budget of the complete instrument.
What are the key specifications engineers should know about the SY89430VJC?
The SY89430VJC is a 50 MHz to 950 MHz programmable synthesizer with differential PECL output, a maximum peak-to-peak jitter of 25 ps, and selectable 5 V or 3.3 V operation. According to the manufacturer datasheet, it includes a synthesized architecture, internal quartz reference, minimal frequency over-shoot, a 3-wire serial interface, and a parallel power-on interface. The device is packaged in a 28-pin PLCC J-lead configuration.

Technische Referenzdaten für SY89430VJC – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the SY89430VJC when the design needs a programmable synthesized clock from 50 MHz to 950 MHz, differential PECL outputs, and no more than 25 ps peak-to-peak jitter. Its serial interface is useful for controlled reprogramming, while the parallel power-on interface suits systems with fixed settings. The 5 V or 3.3 V supply options provide flexibility, but the selected configuration and all receiver thresholds must be verified against the complete system. Do not use a similar ordering suffix as a substitute merely because it is also described as a 28-LCC synthesizer. No cross-brand drop-in alternative was verified with the required combination of PLCC footprint, pin functions, programming method, PECL output, and frequency range. If the SY89430VJC does not meet those requirements, treat any substitution as a redesign requiring schematic and PCB review rather than an automatic replacement.

Vergleich mit Alternativen

Parameter Dieses Produkt
Package 28-pin PLCC (J-lead)
Brand Microchip Technology
Device Type Programmable frequency synthesizer
Frequency Range 50 MHz to 950 MHz
Maximum Output Frequency 950 MHz
Supply Voltage Options 5 V or 3.3 V
Output Type Differential PECL
Peak-to-Peak Output Jitter 25 ps maximum
Programming Interface 3-wire serial and parallel power-on
Frequency Transition Behavior Minimal frequency over-shoot

Wichtigste Unterscheidungsmerkmale

  • Broad programmable output range (vs. No verified drop-in alternative was established)
  • Low differential output jitter (vs. No verified drop-in alternative was established)
  • Flexible programming and startup options (vs. No verified drop-in alternative was established)
  • Reduced frequency-transition overshoot (vs. No verified drop-in alternative was established)

Designhinweise

Route both differential PECL outputs as a controlled-impedance pair with consistent spacing and geometry. Keep the traces short, avoid stubs, and place output termination according to the receiver and board-impedance design. Reference-ground each clock path carefully because mismatched return paths can increase jitter and differential-mode noise even when the synthesizer itself is operating correctly.

Place the device bypass capacitors close to the supply and ground pins, with the shortest possible connection to the relevant return plane. Separate clock routing from switching-node and high-current supply paths to prevent supply disturbance from coupling into the reference or output circuitry. The selected 5 V or 3.3 V configuration must also be checked against every output-amplitude and input-logic requirement in the system.

Treat the clock output as a high-speed differential signal rather than a general-purpose logic output. Confirm receiver thresholds, source amplitude, load capacitance, termination topology, and maximum operating frequency before layout sign-off. At frequencies approaching 950 MHz, interconnect loss, vias, connector launches, and test-probe capacitance can materially degrade edge quality and the usable jitter budget.

Do not substitute a similarly named SY89430 order code based on the 28-LCC package alone. Verify the exact MPN, supply option, temperature rating, lead configuration, and tape-and-reel attributes against the manufacturer ordering information. Also follow the documented S_LOAD edge and setup-and-hold requirements so the configuration latch captures the intended frequency settings.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The available catalog pages do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The device is a clock and timing IC rather than an automotive-qualified product.

Daten verifiziert am: 2026-11-16 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

SY89430VJC datasheet SY89430VJC pinout SY89430VJC datasheet pdf SY89430VJC specifications SY89430VJC 950 MHz SY89430VJC PLCC-28 SY89430VJC replacement SY89430VJC equivalent SY89430VJC price SY89430VJC stock Microchip SY89430VJC SY89430VJC clock synthesizer application

Verwandte Bauteile & Begriffe

Microchip Technology SY89430VJC SY89430VJZ SY89430VJC-TR frequency synthesizer programmable clock generator PLL clock and timing IC integrated circuit semiconductor differential PECL 3-wire serial interface parallel power-on interface synthesized architecture internal quartz reference peak-to-peak output jitter frequency over-shoot 50 MHz 950 MHz 5 V 3.3 V PLCC-28 J-lead package surface mount
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen