SY89430VJC - 950 MHz Clock Synthesizer | Microchip
N.º da peça: SY89430VJC ✓ AtivoSY89430VJC Visão geral
A frequency synthesizer generates or distributes a stable clock derived from a controllable reference source. Within clock and timing electronics, the SY89430VJC belongs to the PLL and clock-generator hierarchy and supports serialized or parallel configuration, allowing it to serve as the timing backbone for communications, instrumentation, industrial control, and test systems.
Key features include a synthesized architecture, minimal frequency over-shoot, a 3-wire serial interface, a parallel interface for power-on configuration, and an internal quartz reference. Differential PECL outputs provide a maximum frequency of 950 MHz, while the specified peak-to-peak output jitter is no more than 25 ps. These characteristics support high-speed clocking requirements where timing margin and reference stability are important.
The device accepts either 5 V or 3.3 V operation, depending on the selected configuration, and its broad tuning range allows one clock architecture to cover multiple system frequencies. The serial interface captures programmed values when the load signal changes state, making it practical for controlled test and measurement setups. A parallel power-on interface offers an alternative configuration path when the required divider and frequency settings are fixed in the system.
Typical uses include laboratory clock sources, communications equipment, semiconductor test systems, frequency-generation instrumentation, and industrial data-acquisition platforms. The differential PECL interface is particularly appropriate for circuits designed around high-speed ECL-compatible clocking, although downstream logic compatibility must be confirmed against voltage and termination requirements.
Layout should preserve short, controlled-impedance clock paths and keep the reference, power, and decoupling connections close to the device. Differential routing must maintain consistent spacing and termination, and unused clock outputs should be handled according to the manufacturer datasheet. Adequate bypass capacitance and a clean reference path help preserve low jitter and avoid unexpected overshoot during frequency transitions.
This page combines the programming features, package information, clocking characteristics, application guidance, and engineering considerations needed to evaluate the SY89430VJC. It also distinguishes the verified device capabilities from unverified details, helping engineers move from component selection to a correctly implemented 950 MHz clock source.
Alternativas drop-in para SY89430VJC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasSY89430VJC Especificações
| Device Type | Programmable frequency synthesizer |
| Frequency Range | 50 MHz to 950 MHz |
| Maximum Output Frequency | 950 MHz |
| Supply Voltage Options | 5 V or 3.3 V |
| Tipo de saída | Differential PECL |
| Peak-to-Peak Output Jitter | 25 ps maximum |
| Architecture | Synthesized |
| Serial Control Interface | 3-wire serial interface |
| Parallel Configuration | Parallel interface for power-on |
| Internal Reference | Internal quartz reference |
| Nominal Reference Frequency | 25 MHz |
| Frequency Transition Behavior | Minimal frequency over-shoot |
| Encapsulamento | 28-pin PLCC (J-lead) |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do SY89430VJC 28-pin plcc (j-lead)
Configuração de pinos para SY89430VJC (pacote 28-pin plcc (j-lead)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para SY89430VJC.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
SY89430VJC é adequado para 6 aplicaçãos: Communications Clock Generation, Semiconductor Test Systems, Frequency Generation Instrumentation, Industrial Data Acquisition, High-Speed Interface Timing, RF and Microwave Test Systems.
Communications Clock Generation
The SY89430VJC fits communications systems requiring a programmable differential clock across a broad frequency range. Its synthesized architecture covers 50 MHz to 950 MHz, while the 25 ps maximum peak-to-peak output jitter helps preserve timing margin in high-speed data paths. The 3-wire serial interface permits runtime frequency changes, and the parallel power-on interface supports fixed configurations. Designers should verify that downstream receivers accept PECL levels and use termination matched to the board impedance.
Recomendado
Semiconductor Test Systems
The SY89430VJC can provide programmable clock stimulus for semiconductor test systems operating up to 950 MHz. Its minimal frequency over-shoot is useful when reducing timing excursions during programmed frequency changes, while the low 25 ps peak-to-peak jitter specification supports high-speed edge-sensitive measurements. The serial programming path allows a test sequencer to select operating conditions, and the parallel path provides deterministic power-on settings. Calibration and reference quality remain part of the total measurement uncertainty.
Recomendado
Frequency Generation Instrumentation
The SY89430VJC is appropriate for laboratory frequency-generation instruments that need a selectable differential clock source. Its wide 50 MHz to 950 MHz operating range covers multiple test frequencies without changing the synthesizer architecture. The synthesized internal reference, serial programming, and parallel power-on configuration provide flexible setup workflows for automated or fixed-condition instruments. Output amplitude, common-mode voltage, termination, and channel matching must be checked against the instrument’s downstream clock receiver.
Recomendado
Industrial Data Acquisition
The SY89430VJC can supply a stable, programmable clock to industrial acquisition and control electronics. The synthesized reference reduces dependence on multiple discrete frequency sources, while the serial interface supports configuration from a controller and the parallel interface supports fixed startup conditions. Differential PECL outputs are suited to systems designed for controlled-impedance clock distribution. Engineers should evaluate clock jitter against the acquisition timing budget and separate sensitive clock routing from high-current switching nodes.
Recomendado
High-Speed Interface Timing
The SY89430VJC is suitable for generating clocks for high-speed interfaces when the system requires up to 950 MHz operation and tightly controlled output jitter. Differential PECL outputs can reduce sensitivity to common-mode noise when implemented with controlled-impedance routing and correct termination. The programmable synthesized architecture allows one source to cover several interface rates. Before implementation, confirm the receiver’s voltage thresholds, edge-rate requirements, maximum tolerable jitter, and the effect of PCB loss on the selected clock frequency.
Recomendado
RF and Microwave Test Systems
The SY89430VJC can serve as a local reference-clock source in RF and microwave test systems requiring programmable frequencies up to 950 MHz. Its synthesized architecture supports repeatable clock generation, and the 25 ps maximum peak-to-peak jitter specification is valuable when clock quality contributes to phase noise or conversion accuracy. The differential PECL interface supports controlled clock distribution to RF test modules. System designers must verify module input capacitance, termination requirements, and the total reference contribution to measurement performance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SY89430VJC — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Package | 28-pin PLCC (J-lead) |
| Brand | Microchip Technology |
| Device Type | Programmable frequency synthesizer |
| Frequency Range | 50 MHz to 950 MHz |
| Maximum Output Frequency | 950 MHz |
| Supply Voltage Options | 5 V or 3.3 V |
| Output Type | Differential PECL |
| Peak-to-Peak Output Jitter | 25 ps maximum |
| Programming Interface | 3-wire serial and parallel power-on |
| Frequency Transition Behavior | Minimal frequency over-shoot |
Principais diferenciais
- Broad programmable output range (vs No verified drop-in alternative was established)
- Low differential output jitter (vs No verified drop-in alternative was established)
- Flexible programming and startup options (vs No verified drop-in alternative was established)
- Reduced frequency-transition overshoot (vs No verified drop-in alternative was established)
Notas de projeto
Route both differential PECL outputs as a controlled-impedance pair with consistent spacing and geometry. Keep the traces short, avoid stubs, and place output termination according to the receiver and board-impedance design. Reference-ground each clock path carefully because mismatched return paths can increase jitter and differential-mode noise even when the synthesizer itself is operating correctly.
Place the device bypass capacitors close to the supply and ground pins, with the shortest possible connection to the relevant return plane. Separate clock routing from switching-node and high-current supply paths to prevent supply disturbance from coupling into the reference or output circuitry. The selected 5 V or 3.3 V configuration must also be checked against every output-amplitude and input-logic requirement in the system.
Treat the clock output as a high-speed differential signal rather than a general-purpose logic output. Confirm receiver thresholds, source amplitude, load capacitance, termination topology, and maximum operating frequency before layout sign-off. At frequencies approaching 950 MHz, interconnect loss, vias, connector launches, and test-probe capacitance can materially degrade edge quality and the usable jitter budget.
Do not substitute a similarly named SY89430 order code based on the 28-LCC package alone. Verify the exact MPN, supply option, temperature rating, lead configuration, and tape-and-reel attributes against the manufacturer ordering information. Also follow the documented S_LOAD edge and setup-and-hold requirements so the configuration latch captures the intended frequency settings.
Informações de conformidade
The available catalog pages do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. The device is a clock and timing IC rather than an automotive-qualified product.