TDA8763AM/3/C5 - 10-Bit 30 MSPS Sigma-Delta ADC | NXP
Teilenummer: TDA8763AM/3/C5 ✗ Abgekündigt| Menge | Stückpreis | Gesamt |
|---|---|---|
| 1 | $6.5 | $6,50 |
| 10 | $5.85 | $58,50 |
| 100 | $5.2 | $520,00 |
| 500 | $4.65 | $2.325,00 |
| 1.000 | $4.1 | $4.100,00 |
TDA8763AM/3/C5 Übersicht
A sigma-delta ADC is a converter architecture that oversamples the input signal at many times the Nyquist rate and uses noise shaping plus digital filtering to push quantization noise out of the signal band. The architecture belongs to the broader taxonomy of data converters (ADC -> Nyquist-rate or oversampling converter -> sigma-delta modulator -> integrated ADC IC -> semiconductor), enabling high effective resolution without requiring laser-trimmed component matching. The TDA8763AM/3/C5 supports DC-sampling operation and integrates the modulator plus decimation filtering on-chip.
Key features include 10-bit resolution, 30 MSPS sampling rate, single +5 V analog supply operation, low power consumption suitable for portable or thermally-constrained systems, and CMOS digital I/O for direct connection to ASICs, FPGAs, or DSPs. The device is one variant in the TDA8763AM family, which spans 30/40/50 MHz sampling-speed grades (TDA8763AM/3, /4, /5 respectively) sharing the same SSOP-28 pinout. The 'C5' suffix denotes the 30 MHz grade in tape-and-reel packaging.
Typical applications include digital video broadcast (DVB) IF digitization, CCD/CIS image sensor front ends, industrial process control, instrumentation, and intermediate-frequency sampling for communications receivers. The wide analog input bandwidth and DC sampling capability make it suitable for both baseband and IF signal chains.
When designing with this ADC, ensure that the analog input drive network provides the correct common-mode and termination load specified by the datasheet, and place the supply decoupling capacitors as close as possible to AVDD and AGND. Allow adequate PCB ground plane separation between the analog and digital grounds to avoid coupling switching noise into the analog front end. This page synthesizes distributor pricing, drop-in family variants, and practical design notes for the 30 MHz grade not found in a single source.
Drop-in-Alternativen für TDA8763AM/3/C5 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TDA8763AM/3/C5 (gleiche Bauform und Footprint) – abweichend in Architecture, DC Sampling, Package, Sampling Rate, Operating Temperature.
Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:
TDA8763AM/3/C4
✅ Drop-In✓ Auf Lager
$6.5 / Stück
Datenblatt ansehen →TDA8763AM/4/C5
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
TDA8763AM/5/C5
✅ Drop-In✓ Auf Lager
$7.2 / Stück
Datenblatt ansehen →TDA8763AM/3,118
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TDA8763AM/4,118
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
TDA8763AM/3/C5 Grenzwerte & elektrische Eigenschaften
| Auflösung | 10 bit |
| Abtastrate | 30 MSPS (C5 grade) |
| Number of Inputs | 1 |
| Architecture | Sigma-Delta |
| Analog Supply Voltage | 5 V |
| Gehäuse | SSOP-28 (SOT341-1), 28 leads, 5.3 mm body width |
| Montageart | Surface Mount |
| Data Interface | CMOS parallel |
| Sampling Family Grade | /3 = 30 MHz, /4 = 40 MHz, /5 = 50 MHz |
| Betriebstemperaturbereich | -40 C to +85 C |
| Packaging | Tape & Reel (TR) - ,118 suffix |
| DC Sampling | Allowed (per datasheet) |
| Lead-Free / RoHS | Compliant |
| Family | TDA8763AM (high-speed low-power ADC series) |
TDA8763AM/3/C5 Pin-Konfiguration
| Pin 1 | VDDA — Analog supply voltage (5 V) |
| Pin 2 | VSSA — Analog ground |
| Pin 3 | VIN — Analog input |
| Pin 4 | VSSA — Analog ground |
| Pin 5 | VDDA — Analog supply voltage (5 V) |
| Pin 6 | VREF — Reference voltage decoupling |
| Pin 7 | VSSA — Analog ground |
| Pin 8 | CLK — Clock input |
| Pin 9 | VDDD — Digital supply voltage |
| Pin 10 | VSSD — Digital ground |
| Pin 11 | D0 — Data output bit 0 (LSB) |
| Pin 12 | D1 — Data output bit 1 |
| Pin 13 | D2 — Data output bit 2 |
| Pin 14 | D3 — Data output bit 3 |
| Pin 15 | D4 — Data output bit 4 |
| Pin 16 | D5 — Data output bit 5 |
| Pin 17 | D6 — Data output bit 6 |
| Pin 18 | D7 — Data output bit 7 |
| Pin 19 | D8 — Data output bit 8 |
| Pin 20 | D9 — Data output bit 9 (MSB) |
| Pin 21 | VSSD — Digital ground |
| Pin 22 | VDDD — Digital supply voltage |
| Pin 23 | OE — Output enable |
| Pin 24 | CLKR — Clock return / reference |
| Pin 25 | VSSD — Digital ground |
| Pin 26 | VDDA — Analog supply voltage (5 V) |
| Pin 27 | VSSA — Analog ground |
| Pin 28 | NC — Not connected (per datasheet) |
Typische Anwendungen
TDA8763AM/3/C5 ist geeignet für 6 Anwendungs: DVB / Digital Video IF Sampling, CCD / CIS Image Sensor Digitization, Industrial Process-Control Data Acquisition, Communications IF-Sampling Receiver, Test & Measurement Instrumentation, Medical Imaging Front-End.
DVB / Digital Video IF Sampling
The TDA8763AM/3/C5 is well matched to digitizing the 36 MHz intermediate-frequency output of a DVB tuner chain. Its 30 MSPS sampling rate comfortably exceeds the Nyquist requirement for the 36 MHz IF after digital downconversion, and the 10-bit resolution preserves enough dynamic range for MPEG-2/4 video decoding. The sigma-delta architecture shapes quantization noise out of the baseband video spectrum, which improves demodulator SNR. Place the device close to the tuner IF output with controlled-impedance 50 ohm traces and provide solid AVDD decoupling to limit spurs coupling into the IF signal path.
Empfohlen
CCD / CIS Image Sensor Digitization
The TDA8763AM/3/C5 accepts the analog video output stream from a CCD or CIS image-sensor front end at pixel-clock rates up to 30 MHz, converting each pixel sample to a 10-bit digital code. The DC-sampling capability simplifies AC-coupling decisions in the analog path, and the CMOS digital outputs connect directly to an image-processing ASIC or FPGA. The SSOP-28 footprint keeps the analog front-end compact, critical for handheld scanners and digital still cameras. Use a separate analog ground island under the ADC to prevent pixel-clock noise from coupling into the analog input.
Empfohlen
Industrial Process-Control Data Acquisition
In industrial data-acquisition systems the TDA8763AM/3/C5 provides 10-bit resolution at 30 MSPS for high-speed analog front-ends such as vibration sensors, sonar return signals, and ultrasonic transducers. The wide analog input bandwidth allows the device to sample IF-derived signals directly, removing the need for external mixers in some designs. The SSOP-28 industrial temperature range (-40 C to +85 C) supports factory-floor deployment. Place robust supply-decoupling networks and isolate the digital outputs from analog input traces to avoid crosstalk into measurement channels.
Empfohlen
Communications IF-Sampling Receiver
Software-defined radio and IF-sampling receiver designs use the TDA8763AM/3/C5 to digitize the 10.7 MHz or 21.4 MHz intermediate frequency directly at the output of the final IF stage. At 30 MSPS the converter provides more than 2x oversampling of the IF signal, and the sigma-delta noise-shaping pushes quantization noise outside the channel bandwidth. The single +5 V supply simplifies receiver power-rail design. Connect the digital outputs to an FPGA or DSP for channelization, demodulation, and filtering.
Empfohlen
Test & Measurement Instrumentation
Bench-top and modular instrumentation (oscilloscope front-ends, spectrum-analyzer IF strips, digitizer cards) leverage the TDA8763AM/3/C5 to convert analog measurement signals into the digital domain for analysis by an FPGA or DSP. The 30 MSPS sample rate covers many measurement bandwidths up to about 12 MHz, and the 10-bit resolution supports general-purpose waveform capture. The SSOP-28 footprint allows the ADC to be placed directly adjacent to the analog input connector to minimize trace length and parasitic capacitance.
Empfohlen
Medical Imaging Front-End
Ultrasound and medical-imaging front-ends use the TDA8763AM/3/C5 to digitize analog return signals at 30 MSPS for beamforming and image reconstruction. The 10-bit resolution provides sufficient grayscale depth for diagnostic imaging, and the single +5 V supply simplifies medical-device safety-isolation design. The sigma-delta architecture reduces anti-alias filter complexity by oversampling the input. Place the ADC close to the transducer preamplifier output, maintain creepage and clearance for patient isolation, and provide separate analog and digital ground planes.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TDA8763AM/3/C5 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TDA8763AM/3/C4 | TDA8763AM/4/C5 | TDA8763AM/5/C5 | TDA8763AM/3,118 | TDA8763AM/4,118 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | SSOP-28 (SOT341-1) | SSOP-28 (SOT341-1) - same | SSOP-28 (SOT341-1) - same | SSOP-28 (SOT341-1) - same | SSOP-28 (SOT341-1) - same | SSOP-28 (SOT341-1) - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit | 10 bit |
| Sampling Rate | 30 MSPS | 30 MSPS | 40 MSPS | 50 MSPS | 30 MSPS | 40 MSPS |
| Architecture | Sigma-Delta | Sigma-Delta | Sigma-Delta | Sigma-Delta | Sigma-Delta | Sigma-Delta |
| Analog Supply | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| Lifecycle Status | NRND | NRND | NRND | NRND | NRND | NRND |
Wichtigste Unterscheidungsmerkmale
- Lower power consumption within the same family (vs. TDA8763AM/5/C5)
- Wide-margin oversampling at the 36 MHz DVB IF (vs. TDA8763AM/4/C5 (40 MSPS))
- Long-established NXP/Philips product specification (vs. TDA8763AM/3/C4)
Designhinweise
Place a solid analog ground island under the TDA8763AM/3/C5 SSOP-28 footprint and tie all VSSA pins to it with short, wide traces. Run digital ground (VSSD) on a separate island that joins the analog ground at a single point near the ADC. Decouple each VDDA pin with a 100 nF ceramic plus 10 uF bulk capacitor placed within 3 mm of the package, and place a ferrite bead or small resistor in series with the +5 V analog feed to filter switching noise from upstream regulators.
Drive the analog input (VIN) with a low-impedance, AC- or DC-coupled source per the datasheet's input network (typically a resistive divider plus series resistor to set the input common-mode). The CMOS digital outputs D0-D9 should be routed as a tightly-matched parallel bus with a ground reference trace on each side; add 22-47 ohm series damping resistors near the ADC outputs to suppress transmission-line ringing when driving long PCB traces into an FPGA or ASIC.
Do not exceed the maximum analog input voltage or violate the input common-mode range specified in the datasheet - clipping or distortion at the input cannot be corrected in the digital domain. Ensure the CLK input is a clean, low-jitter source; sigma-delta ADCs are particularly vulnerable to clock-jitter-induced noise folding. For new designs, note the part is NXP NRND - plan a migration path to the /4 or /5 family grade or a current-generation NXP ADC.
Compliance-Informationen
RoHS compliant per NXP product page and DigiKey listing. Not AEC-Q100 qualified (consumer/industrial grade). Halogen-free status not explicitly confirmed in the verified web data.
