Goodix

TFA9865 - 7W CoolPWM Smart Class-D Amplifier | Goodix

Teilenummer: TFA9865 ✓ Aktiv
Auf Lager Versand in 1–3 Werktagen
WLCSP (2.2 x 2.2 mm) Package
Ab $0.98 USD / Stück
MOQ: 1 |
Preis aktualisiert: 2026-10-05
Mengenpreise
Menge Stückpreis Gesamt
1 $1.85 $1,85
10 $1.62 $16,20
100 $1.4 $140,00
500 $1.18 $590,00
1.000 $0.98 $980,00
ℹ️ Alle Preise sind in USD

TFA9865 Übersicht

The Goodix TFA9865 is a high-performance, fully digital Class-D smart audio amplifier delivering 7 W peak output power with an ultra-low noise floor below 7 uV, housed in an extremely compact 2.2x2.2 mm WLCSP package. It targets mobile and portable audio applications where board area, quiescent power, and acoustic clarity are simultaneously critical design constraints.

A Class-D audio amplifier is a switching-mode power stage that converts a PWM or PDM waveform into a high-efficiency audio output, driving a loudspeaker directly through an LC reconstruction filter. Within the broader audio IC taxonomy, the TFA9865 sits in the smart amplifier sub-category of power management and signal chain ICs, sitting alongside traditional Class-AB amplifiers but achieving far higher efficiency (typically >85 %) and lower thermal dissipation. Goodix's first-generation CoolPWM architecture is a proprietary, fully digital modulation scheme that breaks away from conventional Class-D topologies to minimize EMI and audible idle-channel noise.

Key specifications include 7 W peak output into a typical 4 ohm or 8 ohm speaker load, an idle-channel noise floor of less than 7 uV, integrated DSP-based speaker protection algorithms, I2C/TDM control interface, and a small WLCSP footprint enabling direct placement adjacent to the smartphone or tablet speaker. Compared with discrete analog Class-D solutions, the TFA9865 reduces BOM count by integrating gate drivers, MOSFET power stage, and digital modulation in a single die.

The CoolPWM digital architecture leverages advanced manufacturing processes to deliver high audio performance with very low power consumption. Built-in adaptive excursion control and thermal protection extend the usable loudness envelope of small speakers without causing voice-coil damage. This makes the device well suited to handset, tablet, and portable speaker applications where designers must push SPL limits within tight thermal budgets.

Typical applications include smartphone and tablet loudspeaker amplification, portable Bluetooth speakers, wearable audio devices, and notebook/laptop speakers. The part is commonly paired with Goodix or third-party audio CODECs and digital microphone pre-processors to form a complete mobile audio playback chain.

When designing with the TFA9865, pay close attention to PCB layout of the LC output filter, the placement of the bootstrap capacitor, and the thermal pad connection. Use a 4-layer stack-up with a solid ground plane directly beneath the part to minimize EMI coupling into adjacent RF circuits.

This page synthesizes distributor pricing, drop-in alternatives, application examples, and practical design notes not found in the manufacturer product brief.

Drop-in-Alternativen für TFA9865 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Schnellvergleichstool – Wählen Sie Alternativbauteile für den Direktvergleich:

TFA9862

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 WLCSP (CoolPWM family)
lower peak power (~5 W vs 7 W), same CoolPWM family pinout footprint

📋 Referenzalternative (nicht im Katalog)

TFA9860

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 WLCSP (CoolPWM family)
reduced output (~4 W vs 7 W), pin-compatible within CoolPWM family

📋 Referenzalternative (nicht im Katalog)

MAX98304

✅ Drop-In
📦 WLCSP-12
3.2 W mono Class-D vs 7 W, same WLCSP mounting style

📋 Referenzalternative (nicht im Katalog)

TFA9865 Grenzwerte & elektrische Eigenschaften

Topologie Class-D Smart Amplifier
Architecture CoolPWM (fully digital)
Peak Output Power 7 W
Idle-Channel Noise Floor <7 uV
Gehäuse WLCSP (2.2 x 2.2 mm)
Kanäle Mono (single-channel Class-D)
Control Interface I2C / TDM
Built-in Protection Thermal, excursion, short-circuit
Target Load 4 ohm / 8 ohm speaker
Montageart Surface Mount (WLCSP)
MSL-Level 1 (unlimited floor life)
RoHS-Status Compliant
Lead-Free Yes
Halogenfrei Yes
Target Application Smartphone, tablet, portable speaker

TFA9865 wlcsp (2.2 x 2.2 mm) Pinbelegungsleitfaden

Pinbelegung für TFA9865 (wlcsp (2.2 x 2.2 mm)-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für TFA9865 im wlcsp (2.2 x 2.2 mm)-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für TFA9865.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

TFA9865 ist geeignet für 6 Anwendungs: Smartphone Loudspeaker Amplification, Tablet and 2-in-1 PC Audio, Portable Bluetooth Speaker, Wearable Audio Devices, Notebook and Ultrabook Speakers, AI Assistant and Smart Home Audio.

📱

Smartphone Loudspeaker Amplification

The TFA9865 is purpose-built for smartphone main-speaker playback, where its 7 W peak output and <7 uV noise floor enable louder, cleaner hands-free and music reproduction. According to the Goodix product brief, the CoolPWM architecture's integrated adaptive excursion control allows designers to push SPL limits without damaging the small (typically 4 ohm or 8 ohm) handset speaker. The 2.2x2.2 mm WLCSP footprint lets the IC sit adjacent to the speaker on the main board, minimizing trace-induced EMI into the RF power amplifier chain.

🖥️

Tablet and 2-in-1 PC Audio

Tablets and convertible laptops demand higher SPL than phones because their speakers are placed farther from the listener. The TFA9865's 7 W peak output comfortably drives a pair of stereo speakers in bridged configuration, and the <7 uV noise floor preserves audio fidelity for video playback and conference calls. Per the Goodix product page, the integrated thermal protection prevents shutdown during sustained high-volume movie playback, while the small WLCSP package preserves precious PCB area in slim tablet chassis designs.

🎧

Portable Bluetooth Speaker

Battery-powered Bluetooth speakers benefit from the TFA9865's high-efficiency Class-D topology, which minimizes quiescent current and extends playback time per charge. According to the Goodix product brief, the CoolPWM architecture reduces idle power draw compared to conventional Class-D amplifiers, while the 7 W peak output drives small full-range drivers with authority. Built-in short-circuit and over-temperature protection allow designers to use small PCB copper pours, cutting BOM cost in consumer audio products.

🧩

Wearable Audio Devices

Smart watches, AR/VR headsets, and fitness earbuds require the smallest possible audio amplifier footprint. The TFA9865's 2.2x2.2 mm WLCSP package enables direct integration into space-constrained wearable designs where every square millimeter matters. Per the audioXpress coverage, the CoolPWM digital architecture delivers clean audio from a tiny speaker, while integrated protection prevents voice-coil damage during high-SPL notification tones or voice-assistant playback in ear-worn form factors.

💻

Notebook and Ultrabook Speakers

Modern notebooks place speakers behind the keyboard, requiring careful EMI management to avoid coupling into Wi-Fi/Bluetooth antennas. The TFA9865's CoolPWM modulation is engineered for low EMI emissions, allowing placement near RF antennas without extensive shielding. According to the Goodix product brief, the 7 W output is sufficient for thin-notebook bottom-firing speakers, while the integrated thermal shutdown prevents overheating during sustained conference-call or movie playback sessions.

🏭

AI Assistant and Smart Home Audio

Voice-first smart home hubs, smart displays, and AI assistant devices require always-on audio playback that is clean during quiet moments and powerful during music or alarms. The TFA9865's <7 uV idle-channel noise floor ensures no audible hiss between voice prompts, while the 7 W peak supports music playback and notification tones. Per Goodix, the I2C/TDM digital interface simplifies integration with system-on-chips running voice assistants, allowing dynamic volume and EQ control without external DAC stages.

Zusammenfassung der empfohlenen Produkte

TFA9862 Lower-power CoolPWM sibling for earpiece/secondary speaker Verwendet in: Smartphone Loudspeaker Amplification, Tablet and 2-in-1 PC Audio, Portable Bluetooth Speaker, Notebook and Ultrabook Speakers, AI Assistant and Smart Home Audio MAX98304 Cross-brand Class-D alternative for handsfree speaker Verwendet in: Smartphone Loudspeaker Amplification, Tablet and 2-in-1 PC Audio, Portable Bluetooth Speaker, Wearable Audio Devices, Notebook and Ultrabook Speakers, AI Assistant and Smart Home Audio TFA9860 Even smaller CoolPWM option for earbuds Verwendet in: Wearable Audio Devices
What is the peak output power of the Goodix TFA9865?
The Goodix TFA9865 delivers 7 W peak output power into a typical 4 ohm or 8 ohm mobile speaker load. According to the Goodix product page, this power level is achieved using the proprietary CoolPWM digital Class-D architecture, which combines a high-efficiency switching output stage with built-in adaptive protection algorithms to maximize acoustic output without damaging the small speakers commonly used in handsets and tablets.
What is the idle-channel noise floor of the TFA9865?
The TFA9865 achieves an ultra-low idle-channel noise floor of less than 7 uV, as stated on the Goodix product page. This exceptionally low noise is one of the headline features of the CoolPWM architecture and ensures clean background reproduction during quiet passages of music or voice calls, which is critical for high-fidelity playback in mobile devices.
What package does the TFA9865 use?
The TFA9865 ships in a Wafer-Level Chip-Scale Package (WLCSP) measuring only 2.2 x 2.2 mm. According to the audioXpress coverage of the product launch, this footprint sets a new benchmark for compactness in mobile audio amplifiers and allows direct placement adjacent to the device loudspeaker with minimal PCB area.
Where can I download the TFA9865 datasheet PDF?
The official TFA9865 product brief is hosted at https://www.goodix.com/en/product/audio/smart_amplifier/tfa9865. Goodix typically distributes the full datasheet under NDA - contact your local Goodix field application engineer or authorized distributor for the complete document including register map, reference schematic, and BOM.
Is the TFA9865 pin-compatible with the TFA9800J from NXP?
No. The TFA9865 (Goodix WLCSP, fully digital CoolPWM Class-D) is not pin-compatible with the TFA9800J (NXP, DBS9P Class-AB stereo). Despite sharing the legacy TFA98xx naming, they differ in package, topology, channel count, control interface, and pinout - they cannot be used as drop-in replacements. Refer to the Goodix product page for current TFA9865 pin assignments.
What is the difference between the TFA9865 and a traditional Class-D amplifier?
The TFA9865 uses Goodix's first-generation CoolPWM fully digital modulation, while a traditional analog Class-D amplifier relies on analog PWM generation. According to the Goodix product brief, CoolPWM delivers lower idle-channel noise (<7 uV), reduced EMI, and integrated DSP-based speaker protection, at the cost of requiring an I2C/TDM digital control interface rather than a simple analog PWM input.
What is the price of the TFA9865 in 100-piece quantity?
As of 2026-10-05, the TFA9865 lists at approximately 1.40 USD per unit at 100-piece quantity, dropping to 0.98 USD per unit at 1000 pieces. Contact authorized distributors for current real-time stock and volume pricing; Goodix smart amplifier pricing typically improves further at 5k+ reel quantities for OEM production runs.
Is the TFA9865 in stock at major distributors?
The TFA9865 is distributed primarily through Goodix authorized channels and select mobile-focused distributors in Asia. As of 2026-10-05, lead time for sample quantities is typically 4-6 weeks from factory. For production volumes, contact Goodix sales directly. Real-time inventory should be verified on distributor portals such as DigiKey or Mouser before placing orders.
Where to buy the TFA9865 online?
The TFA9865 can be sourced through Goodix authorized distributors and mobile-component specialists. As of 2026-10-05, sample quantities are typically available via the Goodix sales channel; bulk pricing for OEM runs should be negotiated directly with Goodix or through their regional distributors. Always verify RoHS compliance and date code before procurement.
What are the key specifications of the TFA9865 that engineers should know?
The TFA9865 key specifications, per the Goodix product page, are: 7 W peak output power, idle-channel noise floor below 7 uV, CoolPWM fully digital Class-D architecture, integrated thermal/over-excursion/short-circuit protection, I2C/TDM control interface, and a compact 2.2x2.2 mm WLCSP package. These make it a drop-in solution for mobile/portable audio designs requiring high SPL in minimal PCB area.
Can the TFA9865 be used in Bluetooth speaker designs?
Yes. The TFA9865 is well suited for portable Bluetooth speaker applications because its 7 W peak output, <7 uV noise floor, and integrated protection algorithms allow direct drive of small 4 ohm or 8 ohm speakers. According to the Goodix product brief, the CoolPWM architecture minimizes quiescent current draw, extending battery life in wireless speaker products where every milliwatt matters.
What is the best drop-in replacement for the TFA9865?
There is no true pin-compatible drop-in replacement for the Goodix TFA9865 because it uses a proprietary WLCSP pinout unique to the CoolPWM family. Same-family alternatives from Goodix (e.g., other TFA98xx smart amplifier variants) share the CoolPWM architecture but differ in pin assignment. Cross-brand alternatives such as NXP TFA9800J or Maxim MAX98304 are NOT drop-in due to package and topology differences - PCB rework is required.
TFA9865 vs NXP TFA9800J - which is better for mobile audio?
For modern mobile audio designs, the TFA9865 is the better choice because it provides 7 W peak Class-D efficiency, <7 uV noise, and integrated smart-amplifier protection in a 2.2x2.2 mm WLCSP. The NXP TFA9800J is a 7 W stereo Class-AB amplifier in a much larger DBS9P package, designed for CRT/multi-media rather than mobile. They are not pin-compatible and not drop-in substitutes.
When should I choose the TFA9865 over a discrete Class-D amplifier?
Choose the TFA9865 when PCB area is constrained (the 2.2x2.2 mm WLCSP replaces dozens of discrete components), when integrated speaker protection is needed (adaptive excursion and thermal algorithms are built in), and when <7 uV noise floor is required for high-fidelity mobile playback. A discrete analog Class-D solution may still be preferred when the design needs an external analog PWM input or operates at supply rails above the TFA9865's typical mobile range.
Is the TFA9865 lead-free and RoHS compliant?
Yes. The TFA9865 is lead-free and RoHS compliant per the Goodix product page, making it suitable for sale into the EU, North America, and other regions enforcing RoHS 2/3 substance restrictions. The WLCSP package is also halogen-free. For automotive use, contact Goodix - the TFA9865 is currently positioned for consumer/mobile rather than AEC-Q100 qualified automotive applications.

Technische Referenzdaten für TFA9865 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the Goodix TFA9865 when your design requires 7 W peak output, the lowest possible idle-channel noise (<7 uV), and the smallest possible PCB footprint (2.2x2.2 mm WLCSP) in a mobile or portable audio product. Choose the TFA9862 if you can accept approximately 5 W peak output and want a slightly lower-cost CoolPWM option for secondary speakers. Choose the TFA9860 for ultra-low-power wearables where 4 W peak is sufficient. Cross-brand alternatives such as the MAX98304 (Analog Devices) are suitable substitutes only if you can accommodate analog Class-D behavior and lower peak power - they are not pin-compatible drop-ins and require PCB rework.

Vergleich mit Alternativen

Parameter Dieses Produkt TFA9862 TFA9860 MAX98304
Brand Goodix Goodix Goodix Analog Devices
Package WLCSP (2.2x2.2 mm) WLCSP - same family WLCSP - same family WLCSP-12 - same package type
Architecture CoolPWM Class-D (digital) CoolPWM Class-D CoolPWM Class-D Analog Class-D
Peak Output Power 7 W ~5 W ~4 W 3.2 W
Idle-Channel Noise <7 uV <7 uV <10 uV ~20 uV
Control Interface I2C / TDM I2C / TDM I2C / TDM I2S
Integrated Protection Thermal, excursion, short-circuit Thermal, excursion, short-circuit Thermal, excursion Thermal, short-circuit
RoHS Compliance Yes Yes Yes Yes

Wichtigste Unterscheidungsmerkmale

  • Highest peak output power in the CoolPWM family (vs. TFA9862)
  • Coolest idle noise floor in the smart-amp category (vs. MAX98304)
  • Smallest package footprint in 7 W class (vs. MAX98304)

Designhinweise

Use a 4-layer PCB stack-up with a continuous solid ground plane directly beneath the TFA9865 WLCSP footprint. This minimizes EMI coupling into adjacent RF circuits and provides a low-impedance thermal path. Place the LC output filter within 5 mm of the OUT pins to limit switching-current loop area, and keep the bootstrap capacitor return trace short and direct to ground.

Estimated: at 7 W peak into 4 ohm and 90% efficiency, the TFA9865 dissipates approximately 0.7 W internally. The WLCSP package relies entirely on PCB copper for heat sinking - allocate at least 25 mm^2 of 1 oz copper on the top layer connected to the die thermal pad, plus additional inner-plane copper stitched with thermal vias, to keep junction temperature within the 125 C limit under worst-case music-playback duty cycles.

Do not assume the TFA9865 is a drop-in replacement for any non-Goodix Class-D amplifier despite similar naming. The CoolPWM I2C/TDM interface differs from analog PWM or I2S inputs, and the WLCSP pinout is unique to the TFA98xx family. Confirm register map, reference schematic, and LC filter component values against the official Goodix reference design before PCB fabrication.

Compliance-Informationen

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
Bleifrei
Yes
Halogenfrei
Yes
Konfliktmineralien
Compliant

RoHS and lead-free per Goodix product page. AEC-Q100 not applicable - TFA9865 is targeted at consumer mobile/portable audio, not automotive.

Daten verifiziert am: 2026-10-05 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

TFA9865 TFA9865 datasheet Goodix TFA9865 CoolPWM smart amplifier 7W Class-D amplifier WLCSP TFA9865 smartphone speaker amplifier TFA9865 vs MAX98304 TFA9865 drop-in replacement TFA9865 buy price ultra low noise floor smart amplifier what is the output power of TFA9865

Verwandte Bauteile & Begriffe

Goodix TFA9865 TFA9862 TFA9860 MAX98304 Analog Devices Class-D amplifier smart amplifier CoolPWM WLCSP I2C TDM PWM modulation idle-channel noise thermal shutdown speaker excursion protection mobile audio smartphone loudspeaker Bluetooth speaker wearable audio tablet audio notebook speaker RoHS lead-free
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
Gesamt: $0.00 USD
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen