THS1207CDA - 12-Bit 6 MSPS Quad ADC | Texas Instruments
Teilenummer: THS1207CDA ✓ AktivTHS1207CDA Übersicht
An ADC is an interface component that converts an analog voltage into a digital number for processing by a microprocessor, DSP, FPGA, or embedded controller. The THS1207CDA belongs to the ADC and data-converter hierarchy, where simultaneous sampling means all four channels are captured during each conversion cycle. This differs from a multiplexer-based ADC that switches among inputs sequentially and can introduce timing differences between channel measurements.
The principal operating characteristics are 12-bit resolution, a 6 MSPS conversion rate, four simultaneously sampled inputs, and a parallel processor interface. The TI product description also identifies channel auto-scan as an additional operating feature. A 12-bit code provides 4096 quantization levels, while the 6 MSPS rate permits up to six million completed conversion results per second when the data interface and downstream processor can accept that throughput.
The pipelined conversion architecture separates sampling and resolution processing into internal stages. This supports the device's 6 MSPS throughput, but pipeline latency must be considered when aligning outputs with external events. The parallel interface is suited to systems with dedicated bus connections, rather than designs standardized around a serial converter. Because this package exposes numerous digital control and data lines, careful signal-integrity and layout work is important.
Typical uses include multichannel industrial measurement, process-control instrumentation, communications equipment, audio and vibration analysis, and other acquisition systems that need aligned samples. The same-device approach is especially helpful when comparing sensors, monitoring several power rails, or digitizing multiple inputs for real-time signal processing. In these systems, the four channels reduce the need for separate converters when their required timing can be shared.
PCB design should provide a stable reference and supply implementation, short analog input routes, and a controlled parallel-output interface. Input and reference networks require careful component selection because resistor and capacitor parasitics can affect acquisition accuracy. Designers should also confirm that downstream logic timing accommodates converter latency and that the 32-pin TSSOP footprint has adequate clearance under the assembly requirements of the board manufacturer.
This product summary combines the manufacturer specifications, ordering information, package details, and verified substitute research with practical guidance for signal routing, interface timing, and multichannel system design. It is intended to help engineers identify whether the THS1207CDA's simultaneous sampling, conversion rate, resolution, and package meet a new design or PCB-reuse requirement.
Drop-in-Alternativen für THS1207CDA – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
THS1207IDAG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
THS1207CDAG4
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
THS1207IDAR
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
THS1207CDA Grenzwerte & elektrische Eigenschaften
| ADC Resolution | 12 bit |
| Abtastrate | 6 MSPS |
| Number of Input Channels | 4 channels |
| Sampling Architecture | Simultaneous sampling |
| Conversion Architecture | Pipelined |
| Digital Interface | Parallel DSP/microprocessor interface |
| Channel Auto-Scan | Supported |
| Number of Quantization Levels | 4096 levels |
| Gehäuse | 32-pin TSSOP |
| Package Type | TSSOP, gull-wing, rectangular |
| Montageart | Surface mount |
| Temperature Grade | Commercial |
| Betriebstemperaturbereich | 0 °C to +70 °C |
| Number of Terminals | 32 terminals |
THS1207CDA tssop, gull-wing, rectangular Pinbelegungsleitfaden
Pinbelegung für THS1207CDA (tssop, gull-wing, rectangular-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für THS1207CDA.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
THS1207CDA ist geeignet für 6 Anwendungs: Synchronized Industrial Process Measurement, Communications Signal Monitoring, Audio Channel Acquisition, Vibration and Mechanical Analysis, Power Rail Monitoring, Automated Test Equipment.
Synchronized Industrial Process Measurement
The THS1207CDA suits process instrumentation that must compare four sensor or control signals against a common time reference. Its four channels are sampled simultaneously, preventing multiplexer-style timing offsets between measurements, while the 6 MSPS conversion rate supports fast process dynamics. The 12-bit code provides 4096 quantization levels for representing each sampled voltage. Place the converter near the analog inputs, use a low-noise reference network, and connect its parallel output to a DSP or processor capable of accepting the resulting data throughput. Because this is a 32-pin TSSOP device, route sensitive inputs away from digital clock and data lines and verify acquisition settling against the final PCB layout.
Empfohlen
Communications Signal Monitoring
The THS1207CDA can support communications monitoring when four related analog nodes must be captured at the same instant. Its simultaneous-sampling architecture is useful for comparing in-phase and quadrature channels, observing signal quality, or collecting baseband waveforms around a common trigger. The 6 MSPS rate is appropriate for many low- and intermediate-band monitoring tasks, subject to the converter's input bandwidth and SNR. Use short, impedance-controlled analog paths and a stable reference, then transfer each parallel conversion through appropriate bus timing. Validate clock jitter, bus contention, and processor latency because simultaneous sampling alone does not remove timing uncertainty introduced elsewhere in the acquisition chain.
Empfohlen
Audio Channel Acquisition
The THS1207CDA can acquire four audio-related channels with a shared sampling instant, making it useful for comparison, calibration, and multichannel playback monitoring. Its 12-bit resolution and 6 MSPS rate can represent signals up to roughly 3 MHz under ideal Nyquist conditions, although practical bandwidth, distortion, SNR, and anti-alias requirements determine usable audio range. Place input filters close to the converter, maintain a low-noise reference, and isolate the parallel digital bus from the audio input paths. For conventional oversampled audio, confirm that 12-bit performance and the converter's full-scale range meet the system requirement before finalizing the signal chain.
Empfohlen
Vibration and Mechanical Analysis
The THS1207CDA is appropriate for multichannel vibration testing where accelerometers, strain gauges, or other transducers must be sampled concurrently. Four simultaneous channels allow phase relationships between mechanical responses to be evaluated without the sequential channel offset of a multiplexed converter. The 6 MSPS rate supports analysis of a useful portion of the mechanical spectrum, while the 12-bit resolution affects dynamic range and noise floor. Use matched input-conditioning networks, careful grounding, and differential or single-ended routing appropriate to the sensor interface. PCB validation should measure channel skew, noise coupling, and settling because sensor excitation and transducer bandwidth can constrain the practical measurement performance.
Empfohlen
Power Rail Monitoring
The THS1207CDA can monitor four power-related voltages when a controller or data logger requires a simultaneous snapshot of multiple rails. Sampling the channels together reduces the uncertainty caused by measuring rails at different moments and supports rapid detection of sequencing faults or transients. The 6 MSPS rate is fast enough for many monitoring loops, but the usable bandwidth and response depend on the input network, reference stability, and acquisition software. Choose resistor dividers that preserve the required full-scale range, add protection appropriate to the rails, and keep high-current switching nodes physically separated from the analog inputs. Calibrate gain and offset over the expected rail and temperature range.
Empfohlen
Automated Test Equipment
The THS1207CDA fits automated test systems that need four analog observations associated with one stimulus event. Simultaneous sampling allows a controller to compare responses captured under the same operating conditions, while the 6 MSPS rate supports repeated sweeps and moderate-speed transient characterization. The parallel interface is useful when the fixture controller can capture data efficiently, although bus timing and throughput must be checked against the sample rate. Minimize analog trace length, maintain a stable reference, and use separate return paths for digital clock and data lines. Account for pipeline delay when correlating converter outputs with the applied stimulus or trigger event.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für THS1207CDA – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | THS1207IDAG4 | THS1207CDAG4 | THS1207IDAR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 32-pin TSSOP | 32-pin TSSOP | 32-pin TSSOP | 32-pin TSSOP |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Sampling Rate | 6 MSPS | 6 MSPS | 6 MSPS | 6 MSPS |
| Input Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Sampling Method | Simultaneous sampling | Simultaneous sampling | Simultaneous sampling | Simultaneous sampling |
| Digital Interface | Parallel DSP/microprocessor interface | Parallel DSP/microprocessor interface | Parallel DSP/microprocessor interface | Parallel DSP/microprocessor interface |
| Temperature Grade | Commercial, 0 °C to +70 °C | Industrial | Commercial | Industrial |
| Channel Auto-Scan | Supported | Supported | Supported | Supported |
Wichtigste Unterscheidungsmerkmale
- Four channels captured at one time reference (vs. THS1207IDAG4)
- Same 32-TSSOP mechanical footprint for PCB reuse (vs. THS1207CDAG4)
- Commercial operating range with the same family conversion performance (vs. THS1207IDAR)
Designhinweise
Route the four analog inputs as short, controlled-impedance paths and keep them away from the parallel data bus and clock lines. Place input-series resistance, anti-alias filtering, and any reference components close to the converter according to the manufacturer application circuit. Provide a quiet ground-return path for the analog section and use the TSSOP layout and assembly guidance for the selected board process.
The 6 MSPS conversion rate means the parallel interface must be analyzed as a synchronous, high-edge-rate bus. Use short traces, continuous reference planes, appropriate termination where required, and a processor or DSP that can accept the specified output timing. Account for pipeline delay when aligning converted data with a trigger. Validate setup and hold behavior on the assembled board rather than relying only on simulation.
Do not treat simultaneous sampling as a substitute for a complete front-end design. Confirm the full-scale input range, input impedance, source impedance, reference stability, and allowed bandwidth before selecting divider and filter values. A converter operating outside its recommended drive impedance can lose accuracy even though the four channels are sampled at the same instant.
Place bypass and reference-decoupling components at the pins designated by the manufacturer pin table, with short current loops and solid ground connections. Because the THS1207CDA uses a 32-pin TSSOP package, verify lane clearance, solder-mask design, thermal exposure, and assembly-line compatibility. Keep test points away from sensitive input nodes unless their loading has been evaluated.
Compliance-Informationen
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. Confirm the current manufacturer product and quality documentation before production release.