HINWEIS ZUR LETZTEN BESTELLMÖGLICHKEIT: TJA1050T/N1 nähert sich dem End-of-Life. Letztes Bestelldatum: Kontaktieren Sie uns. Verfügbare Alternativbauteile ansehen →
NXP Semiconductors

TJA1050T/N1 - 1 Mbit/s High-Speed CAN Transceiver | NXP

Teilenummer: TJA1050T/N1 ✗ Abgekündigt
4.75 V to 5.25 V Vdss SOIC-8, 8-SO surface mount Package
MOQ: 1 |

TJA1050T/N1 Übersicht

The NXP Semiconductors TJA1050T/N1 is a high-speed CAN bus transceiver in an 8-pin SOIC-8 surface-mount package. It provides differential transmit and receive capability between a CAN protocol controller and a two-wire CAN network, supporting signaling rates up to 1 Mbit/s. The device operates from a 5 V supply with a stated 4.75 V to 5.25 V supply range. Its SO-8 package supports compact PCB layouts for automotive electronics, industrial automation, transport equipment, and embedded control systems.

A CAN transceiver is an interface IC within the physical layer of the Controller Area Network communication standard. It converts the controller's TXD logic signal into a differential bus waveform on CANH and CANL, while the differential receiver converts bus activity into an RXD signal for the CAN controller. This physical-layer device does not itself implement CAN frames, arbitration, acknowledgements, or protocol error management; those functions remain in a separate CAN controller or a microcontroller with an integrated CAN peripheral.

Key characteristics of the TJA1050T/N1 include its 1 Mbit/s maximum high-speed CAN operation, half-duplex communication through one transmitter and one receiver, differential bus outputs, and a transmitter silent mode. The device is intended for 5 V systems, and the VREF pin permits a common-mode voltage reference for the receiver in applications where the controller and transceiver supply arrangements differ. The 8-pin SOIC footprint also supports assembly methods commonly used for industrial and automotive control boards.

The TJA1050 is an established NXP high-speed CAN transceiver generation whose documentation emphasizes improved electromagnetic-emission behavior compared with earlier transceiver families. Differential signaling across CANH and CANL improves noise immunity by rejecting common-mode voltage present on the bus. The transceiver provides the physical signaling layer only, so bit timing, loopback, error frames, and bus-off recovery remain controlled by the CAN controller and system firmware.

Typical applications include vehicle body and comfort modules, industrial PLC interfaces, robotics controllers, elevator systems, building automation equipment, and service-bus nodes. In each case, the TJA1050T/N1 can connect a 5 V CAN controller to a terminated two-wire CAN network. Board-level decisions remain important because a high bit rate can make stub lengths, grounding, shielding, and connector layout as important as the transceiver selection itself.

Design with the TJA1050T/N1 by following the manufacturer datasheet for termination, decoupling, and exposed-bus-node requirements. Place the supply capacitor close to VCC, keep the CANH and CANL routes compact and symmetric, and avoid unnecessary test pads that increase parasitic capacitance. A 120 ohm termination resistor is normally installed at each physical end of the bus rather than at every node. Request the current lifecycle and sourcing position through the Request a Quote form on this page.

This page brings together lifecycle information, an SO-8 pin assignment, verified drop-in successors, application guidance, and a parameter comparison that helps engineers plan migrations without confusing a transceiver replacement with a complete CAN-controller redesign.

Drop-in-Alternativen für TJA1050T/N1 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Varianten dieser Serie

Modelle derselben Serie, die drop-in-kompatibel sind mit TJA1050T/N1 (gleiche Bauform und Footprint) – abweichend in Package, Bus Interface, Product Type, Mounting Type, Lifecycle Status.

Microchip Technology
Package: 8-Pin PDIP (P) or 8-Pin SOIC (SN)
Product Type: CAN Transceiver
Mounting Type: Through-Hole (PDIP) or Surface Mount (SOIC)
NXP Semiconductors
Package: 14-SO
Bus Interface: Differential CAN transmit and differential receive
Product Type: High-speed CAN transceiver
NXP Semiconductors
Package: 8-pin SOIC
Bus Interface: Two-wire differential CAN bus
Product Type: High-speed CAN transceiver
NXP Semiconductors
Package: 8-pin SOIC
Bus Interface: Two-wire CAN bus
Product Type: High-speed CAN transceiver

TJA1051T

✅ Drop-In
NXP Semiconductors
📦 SOIC-8
High-speed CAN transceiver · Two-wire CAN bus · Differential transmit and receive · Automotive high-speed CAN systems · 8-pin SOIC · Surface mount · Active · Compatible with TJA1050

Preis auf Anfrage

Datenblatt ansehen →

TJA1042T

✅ Drop-In
NXP Semiconductors
📦 SOIC-8
High-speed CAN transceiver · 1 Mbps · Two-wire differential CAN bus · TXD and RXD logic signals · Standby mode · Automotive high-speed CAN · 8-pin SOIC · Surface mount

Preis auf Anfrage

Datenblatt ansehen →

TJA1041T/N1

✅ Drop-In
NXP Semiconductors
📦 SOIC-8
High-speed CAN transceiver · Up to 1 Mbit/s · 1/1 half transceiver · Differential CAN transmit and differential receive · Compatible with suitable high-speed CAN protocol controllers · Automotive high-speed CAN nodes · 14-SO · SMD/SMT

Preis auf Anfrage

Datenblatt ansehen →

SN65HVD251DG4

✅ Drop-In
📦 SOIC-8
Cross-brand 8-pin SOIC CAN transceiver with a 4.5 V to 5.5 V supply range; bus timing, fault behavior, and logic thresholds require verification against the TJA1050T/N1

📋 Referenzalternative (nicht im Katalog)

SIT1050T

✅ Drop-In
📦 SOIC-8
Cross-brand 8-pin SOP-8 high-speed CAN transceiver identified as a replacement; supply limits, ESD rating, and timing differ from the NXP TJA1050T/N1

📋 Referenzalternative (nicht im Katalog)

TJA1050T/N1 Technische Daten

Product Type High-speed CAN bus transceiver
CAN Transceiver Configuration 1 transmit / 1 receive half-duplex
Maximum Data Rate 1 Mbit/s
Supply Voltage Range 4.75 V to 5.25 V
Nominal Supply Voltage 5 V
Bus Interface Differential CANH and CANL
Logic Inputs TXD
Logic Output RXD
Transmitter Silent Mode Supported
TXD Dominant Timeout Supported
Gehäuse SOIC-8, 8-SO surface mount
Anzahl der Pins 8 pins
Montageart Surface mount
Transceiver Type CAN transceiver
Protocol Support Controller Area Network physical layer
Communication Mode Half-duplex differential communication
Reference Output VREF pin
Primary Markets Automotive and industrial

TJA1050T/N1 Pin-Konfiguration

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 TXD — Transmit data input from the CAN controller
Pin 2 GND — Ground connection
Pin 3 VREF — Receiver common-mode reference output
Pin 4 RXD — Receive data output to the CAN controller
Pin 5 GND — Ground connection
Pin 6 CANH — Differential CAN bus high terminal
Pin 7 CANL — Differential CAN bus low terminal
Pin 8 VCC — Positive 5 V supply connection

Typische Anwendungen

TJA1050T/N1 ist geeignet für 6 Anwendungs: Automotive Body and Comfort Modules, Industrial PLC and Factory Automation, Robotics and Mobile Platform Communication, Building Automation and HVAC Control, Elevator and Transport Equipment, Communication Hubs and CAN Gateways.

🚗

Automotive Body and Comfort Modules

The TJA1050T/N1 suits 5 V vehicle body controllers, door modules, climate-control units, and seat controllers that communicate over a high-speed CAN network. Its 1 Mbit/s capability provides sufficient bandwidth for switch events, sensor readings, and diagnostic data while differential CANH and CANL signaling improves common-mode noise rejection on vehicle harnesses. The device is used only as the physical-layer transceiver, so a companion CAN controller handles frame identifiers, arbitration, acknowledgements, and fault recovery. Because the TJA1050 is end-of-life, new vehicle platforms should normally evaluate the TJA1051T successor and confirm 3.3 V controller compatibility.

🏭

Industrial PLC and Factory Automation

The TJA1050T/N1 provides the physical CAN link between a PLC module, robot controller, sensor hub, and remote actuator. At a maximum 1 Mbit/s, the interface can carry real-time process data and diagnostics over the same differential bus while providing noise immunity suitable for electrically noisy production equipment. Its 4.75 V to 5.25 V supply range fits established 5 V industrial control boards, and the 8-pin SOIC-8 package simplifies assembly by reusing standard surface-mount footprints. For new equipment, verify whether the newer TJA1042T or TJA1051T offers a better combination of bus timing, protection, and supply availability.

🤖

Robotics and Mobile Platform Communication

The TJA1050T/N1 can connect motor controllers, joint modules, grippers, and a central robot supervisor through a high-speed CAN network. The 1 Mbit/s interface supports coordinated commands, position feedback, fault flags, and diagnostic responses with predictable differential signaling across CANH and CANL. Because the transceiver offers no galvanic isolation, the design must address ground offsets, cable routing, shielding, and bus protection separately. New robotic platforms designed around 3.3 V microcontrollers should give the TJA1051T priority because its 3.3 V logic compatibility can simplify the controller interface.

🏠

Building Automation and HVAC Control

The TJA1050T/N1 is appropriate for building-control nodes that exchange sensor values, damper commands, alarms, and service data over a high-speed CAN segment. Differential bus signaling helps the transceiver reject common-mode disturbances associated with lighting systems, motor drives, and long building wiring. The 5 V operating range integrates directly with established 5 V controller hardware, while the compact SOIC-8 package leaves board area for communications isolation and protection components. Designers should still define termination, maximum stub length, and fault behavior in the bus topology, and should select a supported successor for equipment with a long production lifetime.

🛗

Elevator and Transport Equipment

The TJA1050T/N1 can serve as the CAN physical interface for elevator controllers, door systems, level sensors, and service diagnostics. Its 1 Mbit/s maximum rate provides bandwidth for coordinated motor commands and status reporting, while the half-duplex transmitter and receiver match the normal CAN bus architecture. Transport environments place emphasis on reliable differential reception and defined fault states, so protection components and grounding should be designed alongside the transceiver rather than added only after troubleshooting. For new transport programs, verify the lifecycle, timing, and safety-fit assessment of the TJA1051T or TJA1042T successor.

🌐

Communication Hubs and CAN Gateways

The TJA1050T/N1 fits a CAN-to-embedded gateway that collects diagnostic messages from several 5 V nodes and forwards them to a higher-level processor or network interface. The transceiver's differential CANH and CANL outputs can support 1 Mbit/s communication, making it useful for high-throughput diagnostic aggregation rather than only slow sensor polling. Its 8-pin SOIC-8 package is convenient for compact gateway boards and can be paired with a microcontroller CAN peripheral or a dedicated controller. For a new gateway using 3.3 V logic, the TJA1051T is generally more direct because it removes concerns about RXD and TXD interface levels.

What is the TJA1050T/N1 used for?
The TJA1050T/N1 is an 8-pin high-speed CAN transceiver used to connect a CAN protocol controller to a two-wire differential CAN bus. It converts TXD logic into CANH and CANL bus signals and returns the received bus state on RXD. According to the NXP TJA1050 product information, the device supports signaling up to 1 Mbit/s for automotive and industrial CAN networks. It is a physical-layer device and still requires a separate CAN controller to manage frames, arbitration, acknowledgements, and error handling.
What is the operating voltage of TJA1050T/N1?
The TJA1050T/N1 operates from a nominal 5 V supply within a 4.75 V to 5.25 V operating range. The TJA1050 is designed for classic 5 V CAN nodes rather than 3.3 V-only systems. A 3.3 V controller can be used only when its TXD and RXD levels are compatible with the transceiver's input thresholds and output levels. For a new 3.3 V design, the TJA1051T family is generally the more direct choice because it adds 3.3 V controller compatibility.
What is the maximum CAN data rate of the TJA1050T/N1?
The TJA1050T/N1 supports a maximum CAN signaling rate of 1 Mbit/s. The NXP product information identifies it as a high-speed CAN transceiver, while the component comparison material lists the TJA1050 family at 1 Mb/s. Achieving this rate in a real network also depends on transceiver propagation delay, bus length, termination, node spacing, cable type, and controller timing configuration. Verify the complete bit-timing budget against the manufacturer datasheet rather than treating 1 Mbit/s as a guaranteed rate for every wiring topology.
Where can I download the TJA1050T/N1 datasheet PDF?
The official TJA1050 product page is available on NXP's website at https://www.nxp.com/part/TJA1050T and provides the product overview, lifecycle information, and datasheet access. The manufacturer page identifies the TJA1050 as end-of-life and includes purchasing or replacement information. Use the pin-description table and characteristic tables in that datasheet when assigning PCB tracks, selecting termination, or checking absolute maximum ratings.
What is the TJA1050T/N1 pinout?
The 8-pin SOIC-8 TJA1050T/N1 assigns TXD to pin 1, GND to pins 2 and 5, VREF to pin 3, RXD to pin 4, CANL to pin 7, CANH to pin 6, and VCC to pin 8. Pin 1 is the package's orientation reference and should be checked against the manufacturer pin-description table before layout release. Both ground pins must be connected to the board ground plane, and CANH and CANL must remain a compact, symmetric pair on the PCB.
Where can I buy the TJA1050T/N1?
Use the Request a Quote form on this page to ask for the TJA1050T/N1, quantity, packaging, and delivery requirements. The device is listed by NXP as end-of-life, so availability can vary with remaining inventory and scheduled supply allocations. A direct manufacturer listing and distributor records for the full ordering code TJA1050T/N1,118 identify the part as an 8-SO high-speed CAN transceiver. The quote form is the appropriate route for confirming current stock, traceability, and any migration options.
What is the current price of TJA1050T/N1?
Current commercial pricing for the TJA1050T/N1 should be confirmed through the Request a Quote form on this page. The TJA1050 is end-of-life, so unit economics depend heavily on remaining lot size, date code, traceability documentation, and whether the purchase is for maintenance or a new design. Because legacy inventory can move in small quantities, request a quote using the exact ordering code TJA1050T/N1,118 and the required quantity so the response reflects the intended purchase.
What is the lead time for TJA1050T/N1?
The current lead time for the TJA1050T/N1 is confirmed through the Request a Quote form on this page. Because NXP identifies the TJA1050 as end-of-life, the lead time depends on remaining inventory rather than a standard production schedule. State your required quantity, date-code preference, and target delivery date in the request. For new production programs, evaluate the TJA1051T or TJA1042T successor instead of building a schedule around constrained legacy supply.
Is the TJA1050T/N1 still in stock?
The TJA1050T/N1 is listed by NXP as end-of-life, and distributor search results still identify the full ordering code TJA1050T/N1,118. Current stock should be requested through the Request a Quote form on this page because end-of-life inventory changes without notice. New designs should select a supported successor, while maintenance and repair programs may use available legacy stock after checking date codes, traceability, and storage-history requirements.
What is the best drop-in replacement for TJA1050T/N1?
The TJA1051T is the most direct documented successor to the TJA1050T because it is described as pin-compatible and retains the 8-pin SOIC-8 footprint. It also improves low-emission behavior, provides stronger ESD protection, and supports direct connection to 3.3 V microcontrollers. The TJA1042T is another same-package migration option. Because pin compatibility alone does not guarantee identical timing or fault behavior, compare the manufacturer datasheets and revalidate bus timing before replacing a deployed design.
Can TJA1051T replace TJA1050T/N1?
Yes, the TJA1051T can serve as a drop-in migration option for the TJA1050T/N1 in an 8-pin SOIC-8 design. The migration guidance identifies the TJA1051T as pin-compatible with the TJA1050T and notes improved electromagnetic emission, higher ESD protection, and support for 3.3 V microcontroller logic. Confirm the exact TJA1051T order code, transceiver timing, bus configuration, and any VREF requirements against the target controller before production release.
Is the TJA1051T the same as the TJA1050T/N1?
The TJA1051T is not identical to the TJA1050T/N1, although it is a pin-compatible 8-pin high-speed CAN transceiver with a similar physical interface. The TJA1051T adds lower electromagnetic emissions, improved ESD protection, and compatibility with 3.3 V controller logic. This makes it the preferred successor for new 5 V or mixed-voltage designs, while the end-of-life TJA1050T/N1 remains suitable for maintaining an existing qualified system when appropriate legacy stock is available.
What can replace TJA1050T/N1 in an existing CAN board?
A drop-in replacement must use the same 8-pin SOIC-8 footprint and preserve the TXD, RXD, VREF, CANH, CANL, VCC, and ground connections. The TJA1051T is a leading same-footprint successor, while the TJA1042T provides another supported migration path for appropriate designs. The SN65HVD251DG4 and SIT1050T also appear in replacement listings as 8-pin SOIC/SOP-8 devices, but their logic thresholds, timing, loopback behavior, and fail-safe characteristics must be checked before substitution.
TJA1050T/N1 vs TJA1042T - which is better for a new design?
Choose the TJA1042T for a new design when its documented low-emission behavior, protection features, and controller-interface compatibility better match the system requirements. Choose the TJA1050T/N1 only when maintaining an already qualified assembly or using verifiable legacy inventory is more important than long-term supply continuity. Both use an 8-pin class package for migration, but controller logic levels, timing, VREF use, and bus topology must be checked against each manufacturer datasheet before selecting either part.
What is the best NXP equivalent for TJA1050T/N1?
The best NXP equivalent is the TJA1051T, which is documented as the direct pin-compatible successor to the TJA1050T. It retains a comparable 8-pin surface-mount interface while adding lower emissions, improved ESD protection, and support for 3.3 V microcontrollers. The TJA1042T is another NXP migration option when its electrical and timing characteristics provide a closer match to the target application. NXP's product page remains the authoritative source for current lifecycle and ordering information.
What key specifications of TJA1050T/N1 should engineers know?
The essential TJA1050T/N1 specifications are a 1 Mbit/s maximum high-speed CAN data rate, 4.75 V to 5.25 V supply operation, one transmitter and one receiver in a half-duplex arrangement, and an 8-pin SOIC-8 package. The differential bus pins are CANH and CANL, and the controller-facing pins are TXD and RXD. The device also supports transmitter silent mode, a TXD dominant timeout, and a VREF reference output. These characteristics place it firmly in the classic 5 V CAN transceiver generation.
How is the TJA1050T/N1 used in an industrial CAN system?
In an industrial CAN system, the TJA1050T/N1 connects a 5 V CAN controller to the differential CANH and CANL conductors. Install termination only at the two physical ends of the bus, keep both nodes and stubs within the limits stated by the manufacturer, and provide a low-impedance ground reference for the differential return path. The transceiver handles bus signaling, but the controller and firmware must still implement correct bit timing, error frames, bus-off recovery, node monitoring, and safe startup behavior.

Technische Referenzdaten für TJA1050T/N1 – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the TJA1050T/N1 when maintaining a qualified 5 V CAN assembly and verified legacy inventory is more important than long-term supply continuity. Its 1 Mbit/s differential interface and SOIC-8 footprint fit established high-speed CAN designs. For new products, prefer the TJA1051T because it is documented as pin-compatible, adds improved protection and lower emissions, and supports 3.3 V microcontrollers. Select the TJA1042T when its electrical characteristics better match the target design within the NXP portfolio. SN65HVD251DG4 and SIT1050T can support cross-brand sourcing, but require careful review of logic thresholds, timing, ESD ratings, fail-safe states, and bus configuration. In every case, confirm pin assignment, termination, controller timing, and EMC performance on the final PCB.

Vergleich mit Alternativen

Parameter Dieses Produkt TJA1051T TJA1042T TJA1041T/N1 SN65HVD251DG4 SIT1050T
Package SOIC-8 SOIC-8 - same package SOIC-8 - same package SOIC-8 - same package SOIC-8 - same package SOIC-8 / SOP-8 - same 8-pin footprint
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments Silan Microelectronics
Device Type High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver High-speed CAN transceiver CAN bus transceiver High-speed CAN transceiver

Wichtigste Unterscheidungsmerkmale

  • Documented pin-compatible migration path (vs. TJA1051T)
  • Established high-speed CAN performance (vs. SN65HVD251DG4)
  • Direct NXP ecosystem continuity (vs. SIT1050T)

Designhinweise

Route CANH and CANL as a short, tightly coupled pair with symmetric geometry and a continuous ground reference beneath them. Keep the transceiver, its decoupling capacitor, and the bus connector in the same physical region so the protected logic side is separated from the external bus connector. Avoid long stubs, unnecessary vias, and isolated copper shapes around the differential traces. These layout practices reduce radiated emissions and improve differential signal integrity when the bus operates at the 1 Mbit/s maximum rate.

Connect both ground pins, pins 2 and 5, to the board ground plane, and place the supply bypass capacitor immediately between VCC at pin 8 and the adjacent ground connection. Follow the capacitor value and placement guidance in the manufacturer datasheet. The VREF pin at pin 3 should only be connected or configured according to the receiver reference arrangement specified for the design. Avoid using the VREF pin as a general-purpose supply source for unrelated circuitry.

Install the usual 120 ohm bus termination only at the two physical ends of the CAN network, not at every node, and confirm that the transceiver's TXD input is actively driven during reset. Do not leave TXD floating, because an undefined TXD state can place the transmitter into an unintended state. Also avoid treating the TJA1050T/N1 as a complete CAN controller: frame handling, bit timing, error confinement, and bus-off recovery must be implemented by the CAN controller or microcontroller peripheral.

For a new 3.3 V controller-based design, plan the footprint around the TJA1051T because it supports direct 3.3 V controller interfacing and provides improved ESD protection. If the TJA1050T/N1 must be retained, verify the controller's TXD output amplitude and the transceiver's RXD output level against the controller input thresholds. Revalidate bit timing, propagation delay, bus fault behavior, and EMC performance after any substitution; an identical package does not by itself guarantee identical system timing.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

NXP identifies the TJA1050T as end-of-life. Compliance attributes require confirmation from the current manufacturer product documentation or a supplied declaration for the exact order code.

Daten verifiziert am: 2026-11-14 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

tja1050t datasheet tja1050t cm 118 datasheet tja1050t cm 118 nxp tja1050t schematic TJA1050T/N1 datasheet pdf TJA1050T/N1 pinout TJA1050T/N1 replacement TJA1050T/N1 drop-in equivalent TJA1050T/N1 vs TJA1051T TJA1050T/N1 SOIC-8 CAN transceiver TJA1050T 1 Mbit/s CAN transceiver TJA1050T/N1 buy TJA1050T/N1 lifecycle NXP TJA1050T/N1

Verwandte Bauteile & Begriffe

NXP Semiconductors TJA1050T/N1 TJA1050T/N1,118 TJA1051T TJA1042T TJA1041T/N1 SN65HVD251DG4 SIT1050T Controller Area Network CAN bus CAN transceiver high-speed CAN differential signaling CANH CANL TXD RXD VREF 1 Mbit/s 4.75 V to 5.25 V SOIC-8 surface mount transmitter silent mode TXD dominant timeout automotive electronics industrial automation
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen