TJA1050T/N1 - 1 Mbit/s High-Speed CAN Transceiver | NXP
MPN: TJA1050T/N1 ✗ סוף ייצורTJA1050T/N1 סקירה
A CAN transceiver is an interface IC within the physical layer of the Controller Area Network communication standard. It converts the controller's TXD logic signal into a differential bus waveform on CANH and CANL, while the differential receiver converts bus activity into an RXD signal for the CAN controller. This physical-layer device does not itself implement CAN frames, arbitration, acknowledgements, or protocol error management; those functions remain in a separate CAN controller or a microcontroller with an integrated CAN peripheral.
Key characteristics of the TJA1050T/N1 include its 1 Mbit/s maximum high-speed CAN operation, half-duplex communication through one transmitter and one receiver, differential bus outputs, and a transmitter silent mode. The device is intended for 5 V systems, and the VREF pin permits a common-mode voltage reference for the receiver in applications where the controller and transceiver supply arrangements differ. The 8-pin SOIC footprint also supports assembly methods commonly used for industrial and automotive control boards.
The TJA1050 is an established NXP high-speed CAN transceiver generation whose documentation emphasizes improved electromagnetic-emission behavior compared with earlier transceiver families. Differential signaling across CANH and CANL improves noise immunity by rejecting common-mode voltage present on the bus. The transceiver provides the physical signaling layer only, so bit timing, loopback, error frames, and bus-off recovery remain controlled by the CAN controller and system firmware.
Typical applications include vehicle body and comfort modules, industrial PLC interfaces, robotics controllers, elevator systems, building automation equipment, and service-bus nodes. In each case, the TJA1050T/N1 can connect a 5 V CAN controller to a terminated two-wire CAN network. Board-level decisions remain important because a high bit rate can make stub lengths, grounding, shielding, and connector layout as important as the transceiver selection itself.
Design with the TJA1050T/N1 by following the manufacturer datasheet for termination, decoupling, and exposed-bus-node requirements. Place the supply capacitor close to VCC, keep the CANH and CANL routes compact and symmetric, and avoid unnecessary test pads that increase parasitic capacitance. A 120 ohm termination resistor is normally installed at each physical end of the bus rather than at every node. Request the current lifecycle and sourcing position through the Request a Quote form on this page.
This page brings together lifecycle information, an SO-8 pin assignment, verified drop-in successors, application guidance, and a parameter comparison that helps engineers plan migrations without confusing a transceiver replacement with a complete CAN-controller redesign.
חלופות תחליף ישיר עבור TJA1050T/N1 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TJA1050T/N1 (אותו גורם צורה וטביעת רגל) — שונים ב Package, Bus Interface, Product Type, Mounting Type, Lifecycle Status.
TJA1051T
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TJA1042T
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TJA1041T/N1
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←SN65HVD251DG4
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
SIT1050T
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TJA1050T/N1 מפרטים
| Product Type | High-speed CAN bus transceiver |
| CAN Transceiver Configuration | 1 transmit / 1 receive half-duplex |
| Maximum Data Rate | 1 Mbit/s |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Nominal Supply Voltage | 5 V |
| Bus Interface | Differential CANH and CANL |
| Logic Inputs | TXD |
| Logic Output | RXD |
| Transmitter Silent Mode | Supported |
| TXD Dominant Timeout | Supported |
| מארז | SOIC-8, 8-SO surface mount |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
| Transceiver Type | CAN transceiver |
| Protocol Support | Controller Area Network physical layer |
| Communication Mode | Half-duplex differential communication |
| Reference Output | VREF pin |
| Primary Markets | Automotive and industrial |
תצורת פינים של TJA1050T/N1
| פין 1 | TXD — Transmit data input from the CAN controller |
| פין 2 | GND — Ground connection |
| פין 3 | VREF — Receiver common-mode reference output |
| פין 4 | RXD — Receive data output to the CAN controller |
| פין 5 | GND — Ground connection |
| פין 6 | CANH — Differential CAN bus high terminal |
| פין 7 | CANL — Differential CAN bus low terminal |
| פין 8 | VCC — Positive 5 V supply connection |
יישומים טיפוסיים
TJA1050T/N1 מתאים עבור 6 יישוםs: Automotive Body and Comfort Modules, Industrial PLC and Factory Automation, Robotics and Mobile Platform Communication, Building Automation and HVAC Control, Elevator and Transport Equipment, Communication Hubs and CAN Gateways.
Automotive Body and Comfort Modules
The TJA1050T/N1 suits 5 V vehicle body controllers, door modules, climate-control units, and seat controllers that communicate over a high-speed CAN network. Its 1 Mbit/s capability provides sufficient bandwidth for switch events, sensor readings, and diagnostic data while differential CANH and CANL signaling improves common-mode noise rejection on vehicle harnesses. The device is used only as the physical-layer transceiver, so a companion CAN controller handles frame identifiers, arbitration, acknowledgements, and fault recovery. Because the TJA1050 is end-of-life, new vehicle platforms should normally evaluate the TJA1051T successor and confirm 3.3 V controller compatibility.
מומלץ
Industrial PLC and Factory Automation
The TJA1050T/N1 provides the physical CAN link between a PLC module, robot controller, sensor hub, and remote actuator. At a maximum 1 Mbit/s, the interface can carry real-time process data and diagnostics over the same differential bus while providing noise immunity suitable for electrically noisy production equipment. Its 4.75 V to 5.25 V supply range fits established 5 V industrial control boards, and the 8-pin SOIC-8 package simplifies assembly by reusing standard surface-mount footprints. For new equipment, verify whether the newer TJA1042T or TJA1051T offers a better combination of bus timing, protection, and supply availability.
מומלץ
Robotics and Mobile Platform Communication
The TJA1050T/N1 can connect motor controllers, joint modules, grippers, and a central robot supervisor through a high-speed CAN network. The 1 Mbit/s interface supports coordinated commands, position feedback, fault flags, and diagnostic responses with predictable differential signaling across CANH and CANL. Because the transceiver offers no galvanic isolation, the design must address ground offsets, cable routing, shielding, and bus protection separately. New robotic platforms designed around 3.3 V microcontrollers should give the TJA1051T priority because its 3.3 V logic compatibility can simplify the controller interface.
מומלץ
Building Automation and HVAC Control
The TJA1050T/N1 is appropriate for building-control nodes that exchange sensor values, damper commands, alarms, and service data over a high-speed CAN segment. Differential bus signaling helps the transceiver reject common-mode disturbances associated with lighting systems, motor drives, and long building wiring. The 5 V operating range integrates directly with established 5 V controller hardware, while the compact SOIC-8 package leaves board area for communications isolation and protection components. Designers should still define termination, maximum stub length, and fault behavior in the bus topology, and should select a supported successor for equipment with a long production lifetime.
מומלץ
Elevator and Transport Equipment
The TJA1050T/N1 can serve as the CAN physical interface for elevator controllers, door systems, level sensors, and service diagnostics. Its 1 Mbit/s maximum rate provides bandwidth for coordinated motor commands and status reporting, while the half-duplex transmitter and receiver match the normal CAN bus architecture. Transport environments place emphasis on reliable differential reception and defined fault states, so protection components and grounding should be designed alongside the transceiver rather than added only after troubleshooting. For new transport programs, verify the lifecycle, timing, and safety-fit assessment of the TJA1051T or TJA1042T successor.
מומלץ
Communication Hubs and CAN Gateways
The TJA1050T/N1 fits a CAN-to-embedded gateway that collects diagnostic messages from several 5 V nodes and forwards them to a higher-level processor or network interface. The transceiver's differential CANH and CANL outputs can support 1 Mbit/s communication, making it useful for high-throughput diagnostic aggregation rather than only slow sensor polling. Its 8-pin SOIC-8 package is convenient for compact gateway boards and can be paired with a microcontroller CAN peripheral or a dedicated controller. For a new gateway using 3.3 V logic, the TJA1051T is generally more direct because it removes concerns about RXD and TXD interface levels.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TJA1050T/N1 — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TJA1051T | TJA1042T | TJA1041T/N1 | SN65HVD251DG4 | SIT1050T |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 - same package | SOIC-8 - same package | SOIC-8 - same package | SOIC-8 - same package | SOIC-8 / SOP-8 - same 8-pin footprint |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Texas Instruments | Silan Microelectronics |
| Device Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | CAN bus transceiver | High-speed CAN transceiver |
מבדילים עיקריים
- Documented pin-compatible migration path (לעומתTJA1051T)
- Established high-speed CAN performance (לעומתSN65HVD251DG4)
- Direct NXP ecosystem continuity (לעומתSIT1050T)
הערות תכנון
Route CANH and CANL as a short, tightly coupled pair with symmetric geometry and a continuous ground reference beneath them. Keep the transceiver, its decoupling capacitor, and the bus connector in the same physical region so the protected logic side is separated from the external bus connector. Avoid long stubs, unnecessary vias, and isolated copper shapes around the differential traces. These layout practices reduce radiated emissions and improve differential signal integrity when the bus operates at the 1 Mbit/s maximum rate.
Connect both ground pins, pins 2 and 5, to the board ground plane, and place the supply bypass capacitor immediately between VCC at pin 8 and the adjacent ground connection. Follow the capacitor value and placement guidance in the manufacturer datasheet. The VREF pin at pin 3 should only be connected or configured according to the receiver reference arrangement specified for the design. Avoid using the VREF pin as a general-purpose supply source for unrelated circuitry.
Install the usual 120 ohm bus termination only at the two physical ends of the CAN network, not at every node, and confirm that the transceiver's TXD input is actively driven during reset. Do not leave TXD floating, because an undefined TXD state can place the transmitter into an unintended state. Also avoid treating the TJA1050T/N1 as a complete CAN controller: frame handling, bit timing, error confinement, and bus-off recovery must be implemented by the CAN controller or microcontroller peripheral.
For a new 3.3 V controller-based design, plan the footprint around the TJA1051T because it supports direct 3.3 V controller interfacing and provides improved ESD protection. If the TJA1050T/N1 must be retained, verify the controller's TXD output amplitude and the transceiver's RXD output level against the controller input thresholds. Revalidate bit timing, propagation delay, bus fault behavior, and EMC performance after any substitution; an identical package does not by itself guarantee identical system timing.
מידע על תאימות
NXP identifies the TJA1050T as end-of-life. Compliance attributes require confirmation from the current manufacturer product documentation or a supplied declaration for the exact order code.