Texas Instruments

TLV274IPW - 3MHz Quad Rail-to-Rail Op Amp | Texas Instruments

Teilenummer: TLV274IPW ✓ Aktiv
2.7 V to 16 V Vdss 550 µA per channel Id 14-pin TSSOP Package
MOQ: 1 |

TLV274IPW Übersicht

Texas Instruments TLV274IPW is a four-circuit, low-power operational amplifier featuring 3 MHz gain-bandwidth product, 2.4 V/µs slew rate, and rail-to-rail output operation from a 2.7 V to 16 V supply. Each amplifier draws 550 µA, and the device is offered in a 14-pin TSSOP package rated for an extended industrial temperature range of -40°C to +125°C.

An operational amplifier is a voltage-feedback analog IC that amplifies the difference between its differential inputs while rejecting signals common to both inputs. The TLV274 belongs to the operational-amplifier hierarchy, where it serves as a low-dropout signal-conditioning building block within analog, mixed-signal, instrumentation, and embedded-control systems. Rail-to-rail output capability lets its output approach the supply rails, improving dynamic range in low-voltage designs where conventional fixed-output amplifiers would lose useful signal range.

The TLV274 combines a 3 MHz bandwidth with low 550 µA-per-channel supply current, making it suitable for portable and industrial systems that require higher bandwidth than ultra-low-power amplifiers but lower power consumption than high-speed general-purpose devices. Its 2.4 V/µs slew rate supports faster output transitions, while 39 nV/Hz input voltage noise helps preserve small-signal fidelity in filtering and sensor-conditioning circuits. Input bias current is specified at 39 pA, supporting high-impedance source applications.

The device operates across a broad 2.7 V to 16 V supply range and uses a CMOS voltage-feedback architecture. Four independent amplifiers in one package reduce board area in applications requiring parallel signal channels. Its rail-to-rail output stage is the defining feature relative to the TLC27x family, although input common-mode behavior and noise characteristics must still be checked against the system requirements.

Typical uses include portable instrumentation, low-side current measurement, sensor amplification, active filters, buffer stages, and general-purpose signal conditioning. In a current-sense amplifier, the amplifier boosts the small voltage produced across a shunt resistor while its low bias current limits loading of the sensing element. In an active filter, the 3 MHz bandwidth provides headroom for closed-loop response above the filter corner frequency.

Designers should confirm output-current capability, input common-mode range, unity-gain stability, and noise performance for the selected feedback topology. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs should use guarded, short traces to reduce leakage and interference.

Drop-in-Alternativen für TLV274IPW – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

TLV2741IPW

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin TSSOP
Adds 1 enable-function difference from the non-enabled TLV274IPW while retaining the 4-channel, 3 MHz, 550 uA per channel family platform

📋 Referenzalternative (nicht im Katalog)

TLV2742IPW

✅ Drop-In ⚠️ Spezifikationen ungeprüft
📦 14-pin TSSOP
Adds 1 shutdown-function difference from the non-enabled TLV274IPW while retaining the 4-channel, 3 MHz, 550 uA per channel family platform

📋 Referenzalternative (nicht im Katalog)

TLV2774CPW

✅ Drop-In
📦 14-pin TSSOP
Uses the same 14-pin TSSOP footprint but changes the amplifier family and therefore at least 1 core bandwidth or power parameter

📋 Referenzalternative (nicht im Katalog)

TLV2774AIPW

✅ Drop-In
📦 14-pin TSSOP
Uses the same 14-pin TSSOP footprint with a different TLV2774 family configuration affecting at least 1 core bandwidth or power parameter

📋 Referenzalternative (nicht im Katalog)

TLV274IPW Grenzwerte & elektrische Eigenschaften

Amplifier Count 4 circuits
Architecture Voltage-feedback CMOS operational amplifier
Supply Voltage Range 2.7 V to 16 V
Maximum Supply Voltage 16 V
Gain-Bandwidth Product 3 MHz per channel
Slew Rate 2.4 V/µs
Versorgungsstrom 550 µA per channel
Output Topology Rail-to-rail output
Input Noise Voltage Density 39 nV/√Hz
Input Bias Current 39 pA
Betriebstemperaturbereich -40°C to +125°C
Gehäuse 14-pin TSSOP
Montageart Surface mount
Product Type General-purpose operational amplifier
RoHS-Status Compliant

TLV274IPW 14-pin tssop Pinbelegungsleitfaden

Pinbelegung für TLV274IPW (14-pin tssop-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für TLV274IPW im 14-pin tssop-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für TLV274IPW.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

TLV274IPW ist geeignet für 6 Anwendungs: Portable Instrumentation, Industrial Sensor Conditioning, Low-Side Current Measurement, Active Filters, Mixed-Signal Interface Buffers, Audio and Communications Conditioning.

📱

Portable Instrumentation

The TLV274IPW fits portable instrumentation because four channels operate from 2.7 V to 16 V while each channel consumes only 550 µA. Its 3 MHz gain-bandwidth product provides useful closed-loop bandwidth for sensor conditioning, buffering, and active-filter stages without requiring the higher current associated with much faster amplifiers. Rail-to-rail output operation also helps retain signal range in low-voltage instruments. The principal design consideration is to verify the input common-mode range at each gain and confirm that the selected feedback network remains stable with the 3 MHz device.

🏭

Industrial Sensor Conditioning

The TLV274IPW is useful for conditioning sensor outputs in industrial equipment where low power and an extended -40°C to +125°C temperature range are important. Its 39 pA input bias current minimizes loading on high-impedance sensors, while 39 nV/√Hz input noise supports low-level signal preservation. Each of the four channels can amplify, buffer, or filter a related input. Designers should check input bias-current variation over temperature, confirm common-mode headroom at the selected supply voltage, and provide clean grounding to avoid converting environmental noise into output errors.

⚡

Low-Side Current Measurement

The TLV274IPW can amplify the small differential voltage generated by a low-side shunt resistor while operating from the same low-voltage rail as many sensor systems. Four independent channels allow simultaneous sensing or use of the remaining amplifiers for gain stages and filtering. The 2.4 V/µs slew rate and 3 MHz bandwidth support moderate-frequency measurement channels, while rail-to-rail output helps use more of the available output range. For accurate results, account for shunt resistance, amplifier input offset and bias current, Kelvin routing, and amplifier saturation near the end of the measured current range.

🔧

Active Filters

The TLV274IPW is suitable for first- and second-order active-filter stages that require more bandwidth than an ultra-low-power amplifier but can operate at 550 µA per channel. Its 3 MHz gain-bandwidth product provides closed-loop response headroom above many audio or low-frequency measurement filter corners. The rail-to-rail output stage can improve output swing in 3.3 V or 5 V systems. Filter design must account for gain-bandwidth allocation, op-amp noise, component tolerances, output loading, and stability, especially when high Q or steep cutoff shapes are required.

🖥️

Mixed-Signal Interface Buffers

The TLV274IPW can buffer analog signals between sensors, converters, or digital processing systems while keeping power consumption modest. Rail-to-rail output operation is valuable when the ADC input range is close to the available supply voltage, and four channels can support several control or measurement paths. The 3 MHz bandwidth is ample for many low- and mid-frequency mixed-signal nodes. Confirm the ADC settling requirements, sampling rate, source impedance, and output-capacitance limits because fast switching edges can require isolation resistors or additional output drive.

🌐

Audio and Communications Conditioning

The TLV274IPW can serve in low-frequency audio, communications, and control-signal paths where rail-to-rail output, modest supply current, and several megahertz of bandwidth are useful. Its 2.4 V/µs slew rate allows larger output-voltage transitions than very slow micropower devices, while the 550 µA per-channel current supports space-constrained portable designs. Four channels reduce board area for multi-path equipment. Check distortion, output-current capability, input-referred noise, and stability in the intended gain configuration; rail-to-rail output alone does not guarantee full rail-to-rail input operation.

What are the key specifications of TLV274IPW that engineers should know?
The TLV274IPW is a four-channel, rail-to-rail-output operational amplifier with 3 MHz gain-bandwidth product, 2.4 V/µs slew rate, and 550 µA supply current per channel. It operates from 2.7 V to 16 V over -40°C to +125°C and is packaged in a 14-pin TSSOP. According to the Texas Instruments TLV274 data sheet, these characteristics position the device between ultra-low-power amplifiers and much faster, higher-current precision amplifiers.
What is the operating voltage of TLV274IPW?
The TLV274IPW operates from 2.7 V to 16 V, with 16 V listed as the maximum supply voltage. According to the Texas Instruments TLV274 data sheet, this range supports single 3.3 V and 5 V systems as well as higher-voltage analog and industrial circuits. Designers should maintain the specified supply limits and provide local bypass capacitance at the device pins.
What is the gain-bandwidth product of TLV274IPW?
The TLV274IPW provides a 3 MHz gain-bandwidth product per amplifier channel. According to the Texas Instruments TLV274 data sheet, this bandwidth is supported by a 2.4 V/µs slew rate and 550 µA per-channel supply current. The combination is useful for moderate-frequency active filters, buffers, sensor amplifiers, and general signal-conditioning stages where low power and useful bandwidth are both important.
Does TLV274IPW have rail-to-rail output?
Yes, the TLV274IPW has a rail-to-rail output stage. According to the Texas Instruments TLV274 part-details information, this makes the device suitable where the output must swing close to either supply rail. The rail-to-rail output characteristic is one reason the TLV27x family is often considered instead of the TLC27x family, although input common-mode limits must be checked independently.
Where can I download the TLV274IPW datasheet PDF?
The official TLV274IPW technical information is available through the Texas Instruments TLV274 product page at https://www.ti.com/product/TLV274. The manufacturer datasheet contains the ordering table, electrical characteristics, pin configuration, typical application circuits, and package information. Use the manufacturer document for design decisions rather than relying on secondary copies, and verify the ordering suffix against TLV274IPW before releasing a schematic.
Where can I find the TLV274IPW pinout?
The TLV274IPW pin configuration is shown in the pin-configuration section of the Texas Instruments TLV274 data sheet. This 14-pin TSSOP device contains four operational amplifiers with their associated supply and ground connections. Before assigning PCB nets, use the manufacturer pin table and package drawing, paying particular attention to channel assignments and the exposed package geometry used by the selected board footprint.
How much current does each TLV274IPW amplifier channel consume?
Each TLV274IPW amplifier channel is specified at 550 µA of supply current. According to the Texas Instruments TLV274 data sheet, four active channels can therefore consume about 2.2 mA before considering additional application-level load. This low current is a principal advantage over 3 MHz amplifiers that operate from substantially higher supply-current levels, particularly in portable instrumentation.
Is TLV274IPW suitable for low-voltage sensor amplification?
The TLV274IPW is suitable for many low-voltage sensor-amplification tasks because it operates from 2.7 V, has rail-to-rail output, and specifies 39 pA input bias current. According to the Texas Instruments TLV274 data sheet, its 39 nV/√Hz input noise supports low-level signal conditioning. The source impedance, output swing, common-mode range, and stability topology should still be evaluated for the exact sensor and gain configuration.
What is the temperature range of TLV274IPW?
The TLV274IPW is specified for an extended industrial operating range of -40°C to +125°C. According to the Texas Instruments TLV274 part-details information, the device supports industrial-temperature operation while drawing only 550 µA per channel. At the upper temperature limit, check output-current limits, DC gain behavior, noise variation, and layout-induced thermal effects across the complete operating environment.
Where to buy TLV274IPW online?
Use the Request a Quote form on this page to request the TLV274IPW, current commercial availability, and any required production quantities. The exact Texas Instruments ordering code is TLV274IPW, and the device is described as an active four-channel, 14-pin TSSOP operational amplifier. Providing the target quantity and required delivery timing directly in the form allows the request to be processed without relying on changing marketplace inventory.
What is the price of TLV274IPW?
The current commercial price for TLV274IPW is handled through the Request a Quote form on this page. Quote pricing can reflect quantity, production schedule, packaging requirements, and market availability, so a static figure may not represent the purchasable terms for a particular order. Submit the required quantity, delivery location, and target date with the quote request for a transaction-specific response.
What is the lead time and stock status for TLV274IPW?
Request the current lead time and stock allocation for TLV274IPW using the Request a Quote form on this page. Texas Instruments identifies the TLV274 family as active, but component availability can vary by order quantity and production schedule. Providing the annual usage, forecast horizon, and required delivery date gives the buyer the most useful basis for confirming allocation and scheduling.
TLV274IPW vs TLV2774CPW: which is better for a 3 MHz design?
The TLV274IPW is the better match when the design specifically targets the TLV27x family behavior of 3 MHz bandwidth and 550 µA per-channel current. The TLV2774CPW belongs to a different amplifier family and should be selected for its own bandwidth, power, and functional requirements rather than treated as an automatic substitute. Compare the two data sheets for input range, output drive, enable behavior, stability, and noise before deciding.
What is the difference between TLV274IPW and TLV2774AIPW?
The TLV274IPW and TLV2774AIPW are different amplifier families with different feature sets and electrical characteristics. The TLV274IPW is specified at 3 MHz bandwidth and 550 µA per channel, while the TLV2774AIPW belongs to the TLV2774 family. Use the manufacturer data sheets to compare rail-to-rail input behavior, output drive, slew rate, supply current, and any shutdown or enable functions relevant to the target circuit.
What can replace TLV274IPW?
A valid replacement for TLV274IPW must use the same 14-pin TSSOP footprint, preserve the pin connections, and remain close in the critical electrical characteristics: 2.7 V to 16 V operation, approximately 3 MHz bandwidth, 550 µA per-channel current, and rail-to-rail output operation. The TLV2741IPW and TLV2742IPW are closely related same-brand candidates, but their enable or shutdown functions must be checked before installation.
When should I choose TLV274IPW over TLV2774CPW?
Choose the TLV274IPW when the circuit was designed around the TLV274 family and prioritizes its specified 3 MHz bandwidth, 550 µA per-channel consumption, and rail-to-rail output operation. Choose the TLV2774CPW instead when its family-specific features meet a higher or more specialized signal-chain requirement. A valid change requires checking the footprint, every pin function, input range, output drive, and stability in the actual feedback network.

Technische Referenzdaten für TLV274IPW – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the TLV274IPW for low-voltage, low-power signal conditioning requiring four channels, 3 MHz bandwidth, 2.4 V/µs slew rate, and rail-to-rail output. Its 550 µA per-channel current is especially useful in portable and industrial systems where four amplifiers would otherwise raise the power budget. Consider TLV2741IPW or TLV2742IPW when an enable or shutdown function would simplify rail management, but verify that the added control function does not change startup behavior or board requirements. Evaluate TLV2774CPW and TLV2774AIPW only when their family-specific electrical characteristics provide a clear advantage over the TLV274 platform. Before replacing any device, compare the manufacturer pin tables, input common-mode range, output drive, noise, bias current, stability curves, and temperature limits. A matching 14-pin TSSOP footprint alone does not establish functional drop-in compatibility.

Vergleich mit Alternativen

Parameter Dieses Produkt TLV2741IPW TLV2742IPW TLV2774CPW TLV2774AIPW
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 14-pin TSSOP 14-pin TSSOP - same footprint 14-pin TSSOP - same footprint 14-pin TSSOP - same footprint 14-pin TSSOP - same footprint
Amplifier Count 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits

Wichtigste Unterscheidungsmerkmale

  • Combines four channels with low per-channel supply current (vs. TLV2774CPW)
  • Rail-to-rail output supports low-voltage signal range (vs. TLV2741IPW)
  • Extended industrial temperature operation (vs. TLV2774AIPW)

Designhinweise

Place the supply bypass capacitor as close as practical to the power pins, and route the ground return directly to the device ground pins without long loops around the board. Keep sensitive input and feedback traces short and away from switching nodes. Because the TLV274IPW is specified at only 550 µA per channel, PCB leakage and contamination can materially affect high-impedance designs even though the specified input bias current is 39 pA.

Check the feedback network against the 3 MHz gain-bandwidth product instead of treating the op amp as an ideal voltage source. Higher closed-loop gains reduce bandwidth and can introduce peaking when interacting with parasitic capacitance. Use the manufacturer stability and typical-characteristic plots for the selected topology, and add an isolation resistor between the amplifier and a capacitively loaded ADC or cable when edge-rate control is required.

Do not assume that rail-to-rail output also means fully rail-to-rail input operation. Check the input common-mode range for the exact supply voltage, gain, and temperature. For sensor interfaces, also verify offset voltage, input-bias-current drift, output-current capability, and saturation behavior. The TLV274IPW's 39 pA nominal input bias current is attractive for high-impedance sources but does not remove leakage from PCB contamination or cables.

Compliance-Informationen

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The component comparison information identifies the TLV274IPW as RoHS compliant. REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status were not established by the manufacturer information used for this page.

Daten verifiziert am: 2026-11-19 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

TLV274IPW datasheet TLV274IPW pinout TLV274IPW datasheet pdf TLV274IPW equivalent TLV274IPW replacement TLV274IPW vs TLV2774CPW TLV274IPW price TLV274IPW stock Texas Instruments TLV274IPW TLV274IPW 14-TSSOP amplifier TLV274IPW 3MHz 550uA TLV274IPW sensor signal conditioning

Verwandte Bauteile & Begriffe

Texas Instruments TLV274IPW TLV2741IPW TLV2742IPW TLV2774CPW TLV2774AIPW operational amplifier voltage-feedback amplifier quad amplifier rail-to-rail output CMOS TSSOP-14 TSSOP surface-mount package gain-bandwidth product slew rate input bias current input voltage noise density sensor signal conditioning active filter low-side current measurement portable instrumentation RoHS
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen