TLV274IPW - 3MHz Quad Rail-to-Rail Op Amp | Texas Instruments
MPN: TLV274IPW ✓ 啟用中TLV274IPW 概覽
An operational amplifier is a voltage-feedback analog IC that amplifies the difference between its differential inputs while rejecting signals common to both inputs. The TLV274 belongs to the operational-amplifier hierarchy, where it serves as a low-dropout signal-conditioning building block within analog, mixed-signal, instrumentation, and embedded-control systems. Rail-to-rail output capability lets its output approach the supply rails, improving dynamic range in low-voltage designs where conventional fixed-output amplifiers would lose useful signal range.
The TLV274 combines a 3 MHz bandwidth with low 550 µA-per-channel supply current, making it suitable for portable and industrial systems that require higher bandwidth than ultra-low-power amplifiers but lower power consumption than high-speed general-purpose devices. Its 2.4 V/µs slew rate supports faster output transitions, while 39 nV/Hz input voltage noise helps preserve small-signal fidelity in filtering and sensor-conditioning circuits. Input bias current is specified at 39 pA, supporting high-impedance source applications.
The device operates across a broad 2.7 V to 16 V supply range and uses a CMOS voltage-feedback architecture. Four independent amplifiers in one package reduce board area in applications requiring parallel signal channels. Its rail-to-rail output stage is the defining feature relative to the TLC27x family, although input common-mode behavior and noise characteristics must still be checked against the system requirements.
Typical uses include portable instrumentation, low-side current measurement, sensor amplification, active filters, buffer stages, and general-purpose signal conditioning. In a current-sense amplifier, the amplifier boosts the small voltage produced across a shunt resistor while its low bias current limits loading of the sensing element. In an active filter, the 3 MHz bandwidth provides headroom for closed-loop response above the filter corner frequency.
Designers should confirm output-current capability, input common-mode range, unity-gain stability, and noise performance for the selected feedback topology. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs should use guarded, short traces to reduce leakage and interference.
直接替換替代品,適用於 TLV274IPW — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
TLV2741IPW
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2742IPW
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2774CPW
✅ 直接替換📋 參考替代品(不在目錄中)
TLV2774AIPW
✅ 直接替換📋 參考替代品(不在目錄中)
TLV274IPW 最大額定值與電氣特性
| Amplifier Count | 4 circuits |
| Architecture | Voltage-feedback CMOS operational amplifier |
| Supply Voltage Range | 2.7 V to 16 V |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 3 MHz per channel |
| Slew Rate | 2.4 V/µs |
| 供應電流 | 550 µA per channel |
| Output Topology | Rail-to-rail output |
| Input Noise Voltage Density | 39 nV/√Hz |
| Input Bias Current | 39 pA |
| 工作溫度範圍 | -40°C to +125°C |
| 封裝 | 14-pin TSSOP |
| 安裝類型 | Surface mount |
| Product Type | General-purpose operational amplifier |
| RoHS 狀態 | Compliant |
TLV274IPW 14-pin tssop 腳位配置指南
TLV274IPW(14-pin tssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV274IPW.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV274IPW 適用於 6 應用s: Portable Instrumentation, Industrial Sensor Conditioning, Low-Side Current Measurement, Active Filters, Mixed-Signal Interface Buffers, Audio and Communications Conditioning.
Portable Instrumentation
The TLV274IPW fits portable instrumentation because four channels operate from 2.7 V to 16 V while each channel consumes only 550 µA. Its 3 MHz gain-bandwidth product provides useful closed-loop bandwidth for sensor conditioning, buffering, and active-filter stages without requiring the higher current associated with much faster amplifiers. Rail-to-rail output operation also helps retain signal range in low-voltage instruments. The principal design consideration is to verify the input common-mode range at each gain and confirm that the selected feedback network remains stable with the 3 MHz device.
推薦
Industrial Sensor Conditioning
The TLV274IPW is useful for conditioning sensor outputs in industrial equipment where low power and an extended -40°C to +125°C temperature range are important. Its 39 pA input bias current minimizes loading on high-impedance sensors, while 39 nV/√Hz input noise supports low-level signal preservation. Each of the four channels can amplify, buffer, or filter a related input. Designers should check input bias-current variation over temperature, confirm common-mode headroom at the selected supply voltage, and provide clean grounding to avoid converting environmental noise into output errors.
推薦
Low-Side Current Measurement
The TLV274IPW can amplify the small differential voltage generated by a low-side shunt resistor while operating from the same low-voltage rail as many sensor systems. Four independent channels allow simultaneous sensing or use of the remaining amplifiers for gain stages and filtering. The 2.4 V/µs slew rate and 3 MHz bandwidth support moderate-frequency measurement channels, while rail-to-rail output helps use more of the available output range. For accurate results, account for shunt resistance, amplifier input offset and bias current, Kelvin routing, and amplifier saturation near the end of the measured current range.
推薦
Active Filters
The TLV274IPW is suitable for first- and second-order active-filter stages that require more bandwidth than an ultra-low-power amplifier but can operate at 550 µA per channel. Its 3 MHz gain-bandwidth product provides closed-loop response headroom above many audio or low-frequency measurement filter corners. The rail-to-rail output stage can improve output swing in 3.3 V or 5 V systems. Filter design must account for gain-bandwidth allocation, op-amp noise, component tolerances, output loading, and stability, especially when high Q or steep cutoff shapes are required.
推薦
Mixed-Signal Interface Buffers
The TLV274IPW can buffer analog signals between sensors, converters, or digital processing systems while keeping power consumption modest. Rail-to-rail output operation is valuable when the ADC input range is close to the available supply voltage, and four channels can support several control or measurement paths. The 3 MHz bandwidth is ample for many low- and mid-frequency mixed-signal nodes. Confirm the ADC settling requirements, sampling rate, source impedance, and output-capacitance limits because fast switching edges can require isolation resistors or additional output drive.
推薦
Audio and Communications Conditioning
The TLV274IPW can serve in low-frequency audio, communications, and control-signal paths where rail-to-rail output, modest supply current, and several megahertz of bandwidth are useful. Its 2.4 V/µs slew rate allows larger output-voltage transitions than very slow micropower devices, while the 550 µA per-channel current supports space-constrained portable designs. Four channels reduce board area for multi-path equipment. Check distortion, output-current capability, input-referred noise, and stability in the intended gain configuration; rail-to-rail output alone does not guarantee full rail-to-rail input operation.
推薦
推薦產品摘要
工程參考資料,適用於 TLV274IPW — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2741IPW | TLV2742IPW | TLV2774CPW | TLV2774AIPW |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin TSSOP | 14-pin TSSOP - same footprint | 14-pin TSSOP - same footprint | 14-pin TSSOP - same footprint | 14-pin TSSOP - same footprint |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
主要差異化特點
- Combines four channels with low per-channel supply current (對比TLV2774CPW)
- Rail-to-rail output supports low-voltage signal range (對比TLV2741IPW)
- Extended industrial temperature operation (對比TLV2774AIPW)
設計說明
Place the supply bypass capacitor as close as practical to the power pins, and route the ground return directly to the device ground pins without long loops around the board. Keep sensitive input and feedback traces short and away from switching nodes. Because the TLV274IPW is specified at only 550 µA per channel, PCB leakage and contamination can materially affect high-impedance designs even though the specified input bias current is 39 pA.
Check the feedback network against the 3 MHz gain-bandwidth product instead of treating the op amp as an ideal voltage source. Higher closed-loop gains reduce bandwidth and can introduce peaking when interacting with parasitic capacitance. Use the manufacturer stability and typical-characteristic plots for the selected topology, and add an isolation resistor between the amplifier and a capacitively loaded ADC or cable when edge-rate control is required.
Do not assume that rail-to-rail output also means fully rail-to-rail input operation. Check the input common-mode range for the exact supply voltage, gain, and temperature. For sensor interfaces, also verify offset voltage, input-bias-current drift, output-current capability, and saturation behavior. The TLV274IPW's 39 pA nominal input bias current is attractive for high-impedance sources but does not remove leakage from PCB contamination or cables.
合規資訊
The component comparison information identifies the TLV274IPW as RoHS compliant. REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status were not established by the manufacturer information used for this page.