Texas Instruments

TLV4112CP - High-Output-Drive Op Amp | Texas Instruments

Teilenummer: TLV4112CP ✓ Aktiv
Approximately 700 µA per channel Vdss More than 300 mA at 5 V Id 8-pin PDIP Package
MOQ: 1 |

TLV4112CP Übersicht

Texas Instruments TLV4112CP is a dual, high-output-drive operational amplifier with rail-to-rail output, a 2.7 MHz unity-gain bandwidth, and a 1.5 V/µs slew rate in an 8-pin PDIP package. It is designed for low-voltage, single-supply systems requiring an amplifier to deliver more than 300 mA at 5 V.

A high-output-drive operational amplifier is a voltage-feedback amplifier optimized for driving capacitive, resistive, and inductive loads beyond the current capability of many general-purpose op amps. The TLV4112CP belongs to the operational-amplifier, analog-signal IC, and power-management IC hierarchy. Its rail-to-rail output stage can approach the positive and negative supply limits, improving dynamic range in low-voltage instrumentation and control systems.

The two amplifier channels provide a 2.7 MHz unity-gain bandwidth, a 1.5 V/µs slew rate, and approximately 700 µA of supply current per channel. Its specified 2.7 V to 6 V operating range supports 3 V and 5 V systems. More than 300 mA of output-drive capability at 5 V makes it useful as a buffer or coil driver when a conventional low-power amplifier would experience excessive distortion or unstable slew behavior.

The TLV4112CP uses rail-to-rail output rather than rail-to-rail input. Its architecture therefore supports wide output swing while requiring the input common-mode range to be checked against the application. Because high output current increases internal power dissipation and reduces available output voltage under load, designers should account for load current, supply voltage, PCB heat spreading, and output-stage stability when driving low-impedance or reactive loads.

Typical uses include audio output stages, transducer excitation, sensor-signal conditioning, low-voltage power-buffer circuits, and small coil drivers. Its dual-channel configuration supports two independent signal paths or a differential driver arrangement when the circuit and load permit it. The 8-pin PDIP package is useful for through-hole prototypes, educational assemblies, and repair applications where a surface-mount footprint is unnecessary.

For reliable high-current operation, decouple the supply pins close to the device, provide adequate copper area for heat dissipation, and isolate large capacitive loads with a series output resistor. Stability should be verified with the actual load because cable capacitance, motor inductance, and output-impedance differences can change the behavior of a high-drive amplifier.

This page combines manufacturer specifications, package details, sourcing guidance, family comparisons, and application-oriented design notes. It also identifies where additional electrical characteristics require direct review of the manufacturer datasheet before a precision design is released.

Drop-in-Alternativen für TLV4112CP – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.

Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.

Alternativen anfordern

TLV4112CP Grenzwerte & elektrische Eigenschaften

Amplifier Type Dual operational amplifier
Topologie Voltage-feedback amplifier
Output Current Capability More than 300 mA at 5 V
Unity-Gain Bandwidth 2.7 MHz
Slew Rate 1.5 V/µs
Versorgungsstrom Approximately 700 µA per channel
Supply Voltage Range 2.7 V to 6 V
Output Rail Capability Rail-to-rail
Number of Channels 2 channels
Shutdown Feature No; shutdown is available on TLV4110 and TLV4113 family variants
Gehäuse 8-pin PDIP
Package Type Through-hole PDIP
Montageart Through-hole

TLV4112CP through-hole pdip Pinbelegungsleitfaden

Pinbelegung für TLV4112CP (through-hole pdip-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.

Pinbelegungsdiagramm für TLV4112CP im through-hole pdip-Gehäuse

Keine detaillierten Pinbelegungsdaten verfügbar für TLV4112CP.

Siehe die Datenblatt für die vollständige Pin-Konfiguration.

Typische Anwendungen

TLV4112CP ist geeignet für 6 Anwendungs: Low-Voltage Audio Buffer, Transducer Excitation, Small Coil Driver, Industrial Sensor Conditioning, Power Buffer Stage, Portable Measurement Interface.

🎧

Low-Voltage Audio Buffer

The TLV4112CP fits low-voltage audio buffers because its rail-to-rail output, 2.7 MHz unity-gain bandwidth, and 1.5 V/µs slew rate support accurate reproduction of moderate-frequency signals on a 2.7 V to 6 V supply. More than 300 mA of drive capability at 5 V provides useful margin for headphone, line-output, or audio distribution stages with higher current than conventional low-power amplifiers can provide. Because the output stage dissipates additional power at high load current, verify thermal rise, output swing, and channel stability against the connected speaker or line network.

🧩

Transducer Excitation

The TLV4112CP can supply the current required by resistive or inductive transducers while preserving a low-voltage control signal. Its more-than-300 mA output-drive capability at 5 V is considerably stronger than the output current normally expected from a small-signal amplifier, while the 2.7 MHz unity-gain bandwidth allows useful control-loop bandwidth. Place the amplifier in an inverting or non-inverting configuration according to the transducer polarity, and add current limiting where the load could exceed the manufacturer electrical limits or introduce excessive power dissipation.

⚡

Small Coil Driver

The high-output-drive architecture makes the TLV4112CP suitable for small electromagnetic coil drivers operating from a 5 V rail. Its output currents in excess of 300 mA at 5 V and 1.5 V/µs slew rate help the amplifier follow current-command waveforms without the severe bandwidth limitation of a low-power op amp. The circuit should include current limiting and flyback protection for inductive kickback, while PCB copper and wiring must be sized to carry the commanded current without excessive voltage drop or thermal stress.

🏭

Industrial Sensor Conditioning

The TLV4112CP can condition sensor signals in a low-voltage industrial module while driving the next stage through a relatively demanding load. Its rail-to-rail output maximizes available signal swing in 3.3 V or 5 V systems, and the 2.7 MHz unity-gain bandwidth supports many moderate-frequency sensing and control applications. Because the amplifier is intended for higher drive current than a precision signal op amp, engineers should evaluate noise, offset, input bias current, and common-mode range against the sensor specification before assigning it to the precision gain stage.

🔋

Power Buffer Stage

The TLV4112CP can serve as a power buffer between a low-current control signal and a resistive or capacitive load in a compact power-management module. The more-than-300 mA drive capability at 5 V and rail-to-rail output reduce the need for a separate output stage in suitable low-voltage systems. Designers must account for the voltage drop across the output impedance, amplifier power dissipation, capacitive-load stability, and the reduced output swing that occurs as load current increases.

📱

Portable Measurement Interface

The TLV4112CP fits portable measurement interfaces that need to drive short cables, sensor inputs, or external analog stages from a 2.7 V to 6 V supply. Its approximately 700 µA per-channel supply current supports low-power operation, while the dual configuration can handle two related analog channels. The 2.7 MHz bandwidth is suitable for signals well below its unity-gain limit. For long interconnects or capacitive inputs, add output isolation, control capacitive loading, and verify the complete signal path with the intended probe or cable.

What is the TLV4112CP?
The TLV4112CP is a dual, high-output-drive operational amplifier designed for single-supply operation from 2.7 V to 6 V. According to the Texas Instruments TLV4112 product page and manufacturer datasheet, each channel has a 2.7 MHz unity-gain bandwidth and a 1.5 V/µs slew rate. The amplifier can source or sink more than 300 mA at a 5 V supply, making it suitable for buffered sensor signals, audio stages, and small coil-driver applications.
How much current can TLV4112CP output?
The TLV4112CP can provide output currents in excess of 300 mA at a 5 V supply, subject to output-voltage headroom, thermal conditions, and load characteristics. The Texas Instruments manufacturer datasheet describes this capability as the defining high-output-drive feature. Continuous maximum current and short-circuit limits must be checked before using the amplifier as a power-output stage rather than a signal amplifier.
What is the supply voltage range of TLV4112CP?
The TLV4112CP operates from 2.7 V to 6 V, making it suitable for 3 V and 5 V single-supply systems. According to the Texas Instruments manufacturer datasheet, the specified 6 V maximum supply is an important boundary for design selection. Designers should also include supply tolerances and transient headroom when defining the operating rail.
Where can I download the TLV4112CP datasheet PDF?
The official TLV4112CP datasheet is reached through the Texas Instruments TLV4112 product page at https://www.ti.com/product/TLV4112. That page provides manufacturer documentation and ordering information. Use the pin-description table, electrical-characteristics table, and application information in the manufacturer datasheet when assigning connections and checking absolute maximum ratings before releasing a PCB design.
Where can I find the TLV4112CP pinout?
The TLV4112CP pinout is defined in the pin-configuration section of the Texas Instruments TLV4112 manufacturer datasheet. This particular TLV4112CP orderable device uses an 8-pin PDIP package. Use the manufacturer pin-description table to map supply, ground, input, output, and any no-connect positions for the exact package rather than relying on a generic diagram from another package in the TLV411x family.
What are the key specifications of TLV4112CP that engineers should know?
The TLV4112CP combines a 2.7 MHz unity-gain bandwidth, 1.5 V/µs slew rate, rail-to-rail output, and more than 300 mA of drive capability at 5 V. According to the Texas Instruments manufacturer datasheet, it also consumes approximately 700 µA per channel and operates from 2.7 V to 6 V. Its 8-pin PDIP package is suited to through-hole assembly and prototype work.
Is TLV4112CP suitable for audio applications?
The TLV4112CP is suitable for audio applications that require more output current than a conventional low-power operational amplifier can provide. Its rail-to-rail output, 2.7 MHz unity-gain bandwidth, and 1.5 V/µs slew rate support low-voltage audio signal paths, while the high-output-drive capability is useful for headphone or line-driver buffers. The actual load impedance and distortion requirements must be checked against the manufacturer electrical-characteristics limits.
Can TLV4112CP drive a coil or inductive load?
The TLV4112CP can drive small inductive loads because its output stage can provide more than 300 mA at 5 V. The Texas Instruments manufacturer page specifically identifies coil-driver use as an application enabled by the high-drive output. Add appropriate current limiting and flyback protection, and verify that load transients do not exceed the amplifier's absolute maximum ratings or destabilize the feedback loop.
What is the difference between TLV4112CP and TLV4113?
The principal family distinction is shutdown capability: the Texas Instruments TLV4112 does not include shutdown, while the TLV4113 family member does. Both are identified by TI as high-output-drive single-supply operational amplifiers in the TLV411x family. Because shutdown changes the circuit function and possibly the pin arrangement, confirm the exact family-member pinout before treating a TLV4113 device as a replacement for TLV4112CP.
What is the difference between TLV4112CP and TLV4110?
The TLV4112 is a dual high-output-drive amplifier without shutdown, while the TLV4110 family member includes shutdown and uses a single-amplifier configuration according to the Texas Instruments family description. The two devices therefore serve different channel-count and shutdown requirements even though they share the high-output-drive concept. Use the exact ordering table and pin configuration for the required suffix before making a PCB-level substitution.
When should I choose TLV4112CP over a general-purpose op amp?
Choose the TLV4112CP when the load requires more than approximately 300 mA at 5 V, where a conventional low-power operational amplifier may become distorted or slew-rate limited. Its 2.7 MHz unity-gain bandwidth and 1.5 V/µs slew rate are useful for moderate-speed signal conditioning, and its dual channels reduce package count in related signal paths. For precision low-current work, a lower-power amplifier may provide lower distortion without the drive burden of the TLV4112CP.
What is the best drop-in replacement for TLV4112CP?
No drop-in replacement should be selected solely from a generic cross-reference result. A valid replacement must match the 8-pin PDIP footprint, pin functions, 2.7 V to 6 V supply range, approximately 300 mA or greater output-drive capability, shutdown arrangement, and thermal constraints of the TLV4112CP. Use the Texas Instruments cross-reference search and the exact manufacturer pinout, then request a quote on this page for the confirmed candidate.
Is there a cross-brand equivalent for TLV4112CP?
A cross-brand equivalent cannot be confirmed from the available component information without risking an incorrect pin or electrical match. A valid substitute must preserve the 8-pin PDIP footprint and maintain the 2.7 V to 6 V supply range, more than 300 mA output-drive capability, rail-to-rail output behavior, and required slew rate. Use the manufacturer cross-reference search for candidate generation and confirm every parameter before approving a replacement.
Where can I buy TLV4112CP online?
Use the Request a Quote form on this page to request TLV4112CP availability, current pricing, minimum order quantity, and lead time. The manufacturer product page identifies the TLV4112 family, while the TLV4112CP orderable device is listed in an 8-pin PDIP package. Providing the exact MPN on the quote request helps avoid confusion with family members that differ in channel count, shutdown capability, or package.
Is TLV4112CP in stock?
Current TLV4112CP inventory and lead time should be confirmed through the Request a Quote form on this page. The exact MPN and package are important because TLV4112 family members can differ in amplifier count, shutdown support, and package configuration. Submit the quantity and target date with the request so the order response reflects the required tube packaging and delivery schedule.
How should I design the PCB around TLV4112CP?
Place the power-bypass capacitor close to the supply pins, keep output-current paths short, and provide enough PCB copper for heat dissipation when driving loads near the device's current capability. Add a small series resistor when capacitive loading could impair stability. The Texas Instruments manufacturer application information should be reviewed for the selected gain setting and load because the high-output stage requires different layout attention from a low-power op amp.

Technische Referenzdaten für TLV4112CP – Vergleich, Designhinweise und Compliance-Informationen.

Auswahlhilfe

Choose the TLV4112CP when a low-voltage circuit needs both dual-channel operation and unusually strong output drive, particularly when the load current can approach or exceed 300 mA at 5 V. Its 2.7 MHz bandwidth and 1.5 V/µs slew rate also make it appropriate for moderate-speed buffers and small coil drivers. Select a conventional precision op amp when noise, offset, input bias current, or micropower operation matters more than load-current capability. Do not substitute a family member with shutdown or a different channel count unless its exact pin configuration is electrically and mechanically interchangeable. Likewise, confirm the 8-pin PDIP footprint and every electrical limit before approving a cross-brand replacement.

Vergleich mit Alternativen

Parameter Dieses Produkt
Brand Texas Instruments
Package 8-pin PDIP
Number of Channels 2 channels
Supply Voltage Range 2.7 V to 6 V
Unity-Gain Bandwidth 2.7 MHz
Slew Rate 1.5 V/µs
Output Drive Capability More than 300 mA at 5 V
Output Swing Rail-to-rail output
Supply Current Approximately 700 µA per channel
Shutdown Feature No

Wichtigste Unterscheidungsmerkmale

  • High output-drive capability (vs. General-purpose low-power operational amplifiers)
  • Rail-to-rail output in a low-voltage device (vs. Non-rail-to-rail amplifiers in the same supply class)
  • Dual-channel high-drive configuration (vs. Single-channel high-output-drive amplifiers)

Designhinweise

High output current increases internal power dissipation even though the TLV4112CP is designed to drive loads above 300 mA at 5 V. Provide continuous copper around the device and through-hole connections, use an appropriate socket or solder joint for thermal conduction, and keep airflow unrestricted when operating near the current capability. Review the manufacturer electrical characteristics for output-current derating and thermal limits before selecting the package for a continuous load.

Do not assume that rail-to-rail output also provides rail-to-rail input operation. Check the input common-mode range in the manufacturer datasheet for the selected TLV4112CP ordering variant and ensure both inputs remain valid during startup, shutdown of upstream circuits, and overdrive. The output can also lose voltage headroom as load current increases, so evaluate output swing at the actual load rather than only at light load.

Use a short, low-impedance supply path and place the bypass capacitor close to the amplifier's supply pins. Keep high-current output wiring physically separate from sensitive input and feedback tracks to reduce feedback through parasitic resistance. If the load is capacitive or connected through a long cable, add a small series output resistor and verify stability at the intended gain. The high-output-drive stage is more likely to interact with load capacitance than a conventional low-power op amp.

Compliance-Informationen

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bleifrei
Unknown
Halogenfrei
Unknown
Konfliktmineralien
Unknown

The manufacturer product page does not expose the requested compliance statuses in the product information used for this page. AEC-Q100 status is therefore recorded as unknown rather than assumed.

Daten verifiziert am: 2026-11-19 – Daten geprüft und kuratiert vom Bauteil-Engineering-Team von XAIPART

Ähnliche Suchanfragen

TLV4112CP datasheet TLV4112CP pinout TLV4112CP datasheet pdf TLV4112CP application circuit TLV4112CP equivalent TLV4112CP replacement TLV4112CP cross reference TLV4112CP 8-PDIP TLV4112CP high output drive TLV4112CP price TLV4112CP stock Texas Instruments TLV4112CP

Verwandte Bauteile & Begriffe

Texas Instruments TLV4112 TLV4112CP TLV4110 TLV4113 OPA828ID High-output-drive operational amplifier Operational amplifier Voltage-feedback amplifier Analog signal IC Power-management IC Rail-to-rail output Unity-gain bandwidth Slew rate Output current Supply current Single-supply operation PDIP-8 Surface-mount family Audio buffer Coil driver Sensor signal conditioning Texas Instruments cross-reference search
Schnellangebot-RFQ
Geben Sie alle Details an – unser Vertriebsteam antwortet innerhalb von 24 Stunden
Teilenummer Hersteller Gehäuse QTY Zielpreis Gesamt
✓
Angebotsanfrage gesendet!

Wir antworten innerhalb von 24 Stunden auf Ihre E-Mail

1
RFQ gesendet
2
Angebot erhalten
3
Bestellung aufgegeben
4
Zahlung
5
Versandt
6
Geliefert
RFQ-Details ansehen