TLV4112CP - High-Output-Drive Op Amp | Texas Instruments
부품 번호: TLV4112CP ✓ 활성TLV4112CP 개요
A high-output-drive operational amplifier is a voltage-feedback amplifier optimized for driving capacitive, resistive, and inductive loads beyond the current capability of many general-purpose op amps. The TLV4112CP belongs to the operational-amplifier, analog-signal IC, and power-management IC hierarchy. Its rail-to-rail output stage can approach the positive and negative supply limits, improving dynamic range in low-voltage instrumentation and control systems.
The two amplifier channels provide a 2.7 MHz unity-gain bandwidth, a 1.5 V/µs slew rate, and approximately 700 µA of supply current per channel. Its specified 2.7 V to 6 V operating range supports 3 V and 5 V systems. More than 300 mA of output-drive capability at 5 V makes it useful as a buffer or coil driver when a conventional low-power amplifier would experience excessive distortion or unstable slew behavior.
The TLV4112CP uses rail-to-rail output rather than rail-to-rail input. Its architecture therefore supports wide output swing while requiring the input common-mode range to be checked against the application. Because high output current increases internal power dissipation and reduces available output voltage under load, designers should account for load current, supply voltage, PCB heat spreading, and output-stage stability when driving low-impedance or reactive loads.
Typical uses include audio output stages, transducer excitation, sensor-signal conditioning, low-voltage power-buffer circuits, and small coil drivers. Its dual-channel configuration supports two independent signal paths or a differential driver arrangement when the circuit and load permit it. The 8-pin PDIP package is useful for through-hole prototypes, educational assemblies, and repair applications where a surface-mount footprint is unnecessary.
For reliable high-current operation, decouple the supply pins close to the device, provide adequate copper area for heat dissipation, and isolate large capacitive loads with a series output resistor. Stability should be verified with the actual load because cable capacitance, motor inductance, and output-impedance differences can change the behavior of a high-drive amplifier.
This page combines manufacturer specifications, package details, sourcing guidance, family comparisons, and application-oriented design notes. It also identifies where additional electrical characteristics require direct review of the manufacturer datasheet before a precision design is released.
드롭인 대체품: TLV4112CP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청TLV4112CP 최대 정격 & 전기적 특성
| Amplifier Type | Dual operational amplifier |
| 토폴로지 | Voltage-feedback amplifier |
| Output Current Capability | More than 300 mA at 5 V |
| Unity-Gain Bandwidth | 2.7 MHz |
| Slew Rate | 1.5 V/µs |
| 공급 전류 | Approximately 700 µA per channel |
| Supply Voltage Range | 2.7 V to 6 V |
| Output Rail Capability | Rail-to-rail |
| Number of Channels | 2 channels |
| Shutdown Feature | No; shutdown is available on TLV4110 and TLV4113 family variants |
| 패키지 | 8-pin PDIP |
| Package Type | Through-hole PDIP |
| 실장 유형 | Through-hole |
TLV4112CP through-hole pdip 핀 구성 가이드
TLV4112CP(through-hole pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: TLV4112CP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
TLV4112CP 적합 용도: 6 애플리케이션s: Low-Voltage Audio Buffer, Transducer Excitation, Small Coil Driver, Industrial Sensor Conditioning, Power Buffer Stage, Portable Measurement Interface.
Low-Voltage Audio Buffer
The TLV4112CP fits low-voltage audio buffers because its rail-to-rail output, 2.7 MHz unity-gain bandwidth, and 1.5 V/µs slew rate support accurate reproduction of moderate-frequency signals on a 2.7 V to 6 V supply. More than 300 mA of drive capability at 5 V provides useful margin for headphone, line-output, or audio distribution stages with higher current than conventional low-power amplifiers can provide. Because the output stage dissipates additional power at high load current, verify thermal rise, output swing, and channel stability against the connected speaker or line network.
추천
Transducer Excitation
The TLV4112CP can supply the current required by resistive or inductive transducers while preserving a low-voltage control signal. Its more-than-300 mA output-drive capability at 5 V is considerably stronger than the output current normally expected from a small-signal amplifier, while the 2.7 MHz unity-gain bandwidth allows useful control-loop bandwidth. Place the amplifier in an inverting or non-inverting configuration according to the transducer polarity, and add current limiting where the load could exceed the manufacturer electrical limits or introduce excessive power dissipation.
추천
Small Coil Driver
The high-output-drive architecture makes the TLV4112CP suitable for small electromagnetic coil drivers operating from a 5 V rail. Its output currents in excess of 300 mA at 5 V and 1.5 V/µs slew rate help the amplifier follow current-command waveforms without the severe bandwidth limitation of a low-power op amp. The circuit should include current limiting and flyback protection for inductive kickback, while PCB copper and wiring must be sized to carry the commanded current without excessive voltage drop or thermal stress.
추천
Industrial Sensor Conditioning
The TLV4112CP can condition sensor signals in a low-voltage industrial module while driving the next stage through a relatively demanding load. Its rail-to-rail output maximizes available signal swing in 3.3 V or 5 V systems, and the 2.7 MHz unity-gain bandwidth supports many moderate-frequency sensing and control applications. Because the amplifier is intended for higher drive current than a precision signal op amp, engineers should evaluate noise, offset, input bias current, and common-mode range against the sensor specification before assigning it to the precision gain stage.
추천
Power Buffer Stage
The TLV4112CP can serve as a power buffer between a low-current control signal and a resistive or capacitive load in a compact power-management module. The more-than-300 mA drive capability at 5 V and rail-to-rail output reduce the need for a separate output stage in suitable low-voltage systems. Designers must account for the voltage drop across the output impedance, amplifier power dissipation, capacitive-load stability, and the reduced output swing that occurs as load current increases.
추천
Portable Measurement Interface
The TLV4112CP fits portable measurement interfaces that need to drive short cables, sensor inputs, or external analog stages from a 2.7 V to 6 V supply. Its approximately 700 µA per-channel supply current supports low-power operation, while the dual configuration can handle two related analog channels. The 2.7 MHz bandwidth is suitable for signals well below its unity-gain limit. For long interconnects or capacitive inputs, add output isolation, control capacitive loading, and verify the complete signal path with the intended probe or cable.
추천
추천 제품 요약
엔지니어링 참조 데이터: TLV4112CP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.7 V to 6 V |
| Unity-Gain Bandwidth | 2.7 MHz |
| Slew Rate | 1.5 V/µs |
| Output Drive Capability | More than 300 mA at 5 V |
| Output Swing | Rail-to-rail output |
| Supply Current | Approximately 700 µA per channel |
| Shutdown Feature | No |
주요 차별점
- High output-drive capability (vs General-purpose low-power operational amplifiers)
- Rail-to-rail output in a low-voltage device (vs Non-rail-to-rail amplifiers in the same supply class)
- Dual-channel high-drive configuration (vs Single-channel high-output-drive amplifiers)
설계 노트
High output current increases internal power dissipation even though the TLV4112CP is designed to drive loads above 300 mA at 5 V. Provide continuous copper around the device and through-hole connections, use an appropriate socket or solder joint for thermal conduction, and keep airflow unrestricted when operating near the current capability. Review the manufacturer electrical characteristics for output-current derating and thermal limits before selecting the package for a continuous load.
Do not assume that rail-to-rail output also provides rail-to-rail input operation. Check the input common-mode range in the manufacturer datasheet for the selected TLV4112CP ordering variant and ensure both inputs remain valid during startup, shutdown of upstream circuits, and overdrive. The output can also lose voltage headroom as load current increases, so evaluate output swing at the actual load rather than only at light load.
Use a short, low-impedance supply path and place the bypass capacitor close to the amplifier's supply pins. Keep high-current output wiring physically separate from sensitive input and feedback tracks to reduce feedback through parasitic resistance. If the load is capacitive or connected through a long cable, add a small series output resistor and verify stability at the intended gain. The high-output-drive stage is more likely to interact with load capacitance than a conventional low-power op amp.
규정 준수 정보
The manufacturer product page does not expose the requested compliance statuses in the product information used for this page. AEC-Q100 status is therefore recorded as unknown rather than assumed.