TS555CDT - 2.7 MHz CMOS Timer | STMicroelectronics
Teilenummer: TS555CDT ✓ AktivTS555CDT Übersicht
A programmable timer is an integrated circuit that generates or measures a time interval using external resistors and capacitors. The TS555 belongs to the 555 timer family within the broader clock and timing IC hierarchy. Its internal voltage reference, comparators, discharge transistor, and flip-flop allow one device to create periodic waveforms, produce fixed-duration pulses, or measure elapsed time. The CMOS implementation retains the familiar timing architecture while reducing supply current and output-transition current spikes.
Key features include a maximum timer frequency of 2.7 MHz, typical supply current of 110 µA at a 5 V supply, and operation across a 2 V to 16 V supply range. These characteristics suit battery-powered timers, low-cost automation circuits, pulse generators, debounce circuits, and general-purpose delay networks. Compared with a bipolar NE555, the CMOS TS555 provides substantially lower consumption and a much higher maximum frequency, supporting smaller timing capacitors and more compact high-frequency implementations.
The TS555 uses the standard 555 timing architecture and remains pin-compatible with the familiar 8-pin NE555 footprint. Timing accuracy is maintained in astable and monostable modes, while reduced supply-current spikes during output transitions can permit smaller decoupling capacitors than a bipolar implementation. The control-voltage pin provides a means of adjusting the internal threshold reference within the device's allowed range.
Typical applications include low-cost oscillators for LED blinking or clock generation, retriggerable and non-retriggerable monostable pulse circuits, transistor switching circuits, sensor debounce networks, delayed-action controls, and low-power embedded timing. In battery-operated products, its low typical supply current reduces standby burden, while the 16 V upper supply limit supports many 12 V industrial systems when voltage and dissipation conditions permit.
When implementing the device, calculate the timing resistors and capacitors for the required frequency and duty cycle, and place the timing capacitor directly at the threshold and trigger pins to minimize noise pickup. Use a stable reference capacitor at the control-voltage pin and provide adequate input bypassing. Confirm that the maximum frequency, supply voltage, output-load capability, and timing tolerances suit the intended operating environment.
This page combines the TS555CDT's principal electrical characteristics, package and pin information, application guidance, and pin-compatible sourcing considerations. It is intended to help engineers identify where the CMOS 555 architecture improves power consumption and frequency capability while preserving the standard timer interface.
Drop-in-Alternativen für TS555CDT – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TS555CDT (gleiche Bauform und Footprint) – abweichend in Operating Modes, Package, Supply Voltage Range, Typical Supply Current, Timer Type.
TS555IDT
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →TS555CDT Technische Daten
| Device Type | Single CMOS programmable timer and oscillator |
| Maximum Frequency | 2.7 MHz |
| Typical Supply Current | 110 µA at 5 V |
| Supply Voltage Range | 2 V to 16 V |
| Operating Modes | Astable and monostable |
| Technology | CMOS |
| Ausgangskonfiguration | Single timer output |
| Gehäuse | 8-pin SOIC |
| Montageart | Surface mount |
| Output Transition Supply-Current Spikes | Reduced compared with bipolar NE555 |
| Timing Accuracy | Maintained in astable and monostable modes |
| Control Reference | External control-voltage support |
TS555CDT Pin-Konfiguration
| Pin 1 | GND — Ground reference |
| Pin 2 | TRIG — Trigger input |
| Pin 3 | OUT — Timer output |
| Pin 4 | RESET — Reset input |
| Pin 5 | CTRL — Control voltage input |
| Pin 6 | THRES — Threshold input |
| Pin 7 | DISCH — Discharge output |
| Pin 8 | VCC — Power supply |
Typische Anwendungen
TS555CDT ist geeignet für 6 Anwendungs: Low-Power Monostable Pulse Generator, LED Flashing and Visual Indicator Oscillator, Industrial Sensor Debounce Circuit, Delay and Retriggerable Control Circuit, Switching and Driver Interface, High-Rate Low-Power Clock or Oscillator.
Low-Power Monostable Pulse Generator
The TS555CDT is well suited to producing a fixed-duration pulse from a trigger event in battery-powered or low-power control systems. Its CMOS architecture draws a typical 110 µA at 5 V, while astable and monostable timing remain accurate according to the STMicroelectronics datasheet. A resistor and timing capacitor at the threshold and trigger nodes establish the pulse width, while the discharge output can drive a transistor or controlled load. The 2 V minimum supply supports low-energy systems, although the timer, timing capacitor, leakage, and load current must be evaluated together. Use the output pin for the pulse signal and the reset pin for controlled initialization or emergency inhibit.
Empfohlen
LED Flashing and Visual Indicator Oscillator
TS555CDT can create a continuous square wave in astable mode to flash an LED, signal a status condition, or drive a low-cost visual indicator. Its maximum frequency of 2.7 MHz gives substantial timing headroom compared with the 0.1 MHz maximum cited for a bipolar NE555, although most LED indicators operate much lower. Two timing resistors and one capacitor determine frequency and duty cycle. The typical 110 µA supply current at 5 V is useful in compact portable products, while reduced output-transition current spikes simplify local bypassing. A current-limiting resistor is mandatory for an LED, and the indicator driver should not exceed the timer output's load capability.
Empfohlen
Industrial Sensor Debounce Circuit
The TS555CDT provides a practical debounce and normalization stage for mechanical switches, reed sensors, or other slow-changing contacts. In a monostable configuration, contact noise can trigger a fixed output pulse instead of propagating multiple false transitions to a controller. The CMOS timer supports a 2 V to 16 V supply range, making it suitable for 5 V logic and many 12 V industrial arrangements when timing values remain within the required operating limits. Place the timing capacitor close to pins 2 and 6 to limit noise pickup, and connect the reset and control pins according to the manufacturer pin-description table. Validate the pulse width against the downstream controller's input filtering and safety requirements.
Empfohlen
Delay and Retriggerable Control Circuit
TS555CDT can implement a delayed or retriggerable control action for relays, valves, and sequential machinery where a fixed timing interval improves repeatability. The monostable architecture accepts an initiating trigger and produces a controlled pulse whose duration is set by external timing components. Its 2.7 MHz maximum rating allows accurate use of relatively short intervals, and the typical 110 µA consumption at 5 V helps limit standby demand. For inductive loads, use a transistor or suitable driver rather than loading the output directly. Confirm whether retriggering matches the required control behavior, and ensure the external timing capacitor has suitable temperature coefficient and leakage characteristics for the required timing tolerance.
Empfohlen
Switching and Driver Interface
The TS555CDT's discharge and output stages can support simple transistor-switching functions in power-control and signal-routing circuits. The discharge output operates with the standard 555 architecture, while the output provides a buffered timing signal. This arrangement is useful when a logic-level output cannot directly supply a transistor base, relay coil, or other higher-current load. The STMicroelectronics description notes reduced supply-current spikes during output transitions, helping maintain supply stability in compact battery-powered designs. Choose external transistor and resistor values for the load current, provide local supply decoupling, and keep high-current return paths separate from sensitive timing nodes to avoid shifting the switching threshold and degrading timing behavior.
Empfohlen
High-Rate Low-Power Clock or Oscillator
TS555CDT can generate a compact periodic clock where a dedicated oscillator would add unnecessary cost or board area. Its 2.7 MHz maximum frequency is much higher than the 0.1 MHz maximum cited for the bipolar NE555, enabling higher-rate waveforms when timing values and output rise time allow. Typical supply current of 110 µA at 5 V preserves low-power operation in embedded equipment. The frequency is set by the external resistor and capacitor network, while duty cycle depends on the two timing resistors. Keep the timing loop compact and away from switching nodes, and verify the actual waveform frequency and jitter on the final board because parasitic capacitance and supply ripple can alter the timing network.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TS555CDT – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TS555IDT |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | STMicroelectronics | STMicroelectronics |
| Maximum Frequency | 2.7 MHz | 2.7 MHz |
| Typical Supply Current | 110 µA at 5 V | 110 µA at 5 V |
| Supply Voltage Range | 2 V to 16 V | 2 V to 16 V |
| Operating Modes | Astable and monostable | Astable and monostable |
| Technology | CMOS | CMOS |
Wichtigste Unterscheidungsmerkmale
- Higher maximum timing frequency than the cited bipolar NE555 (vs. NE555)
- Lower typical supply consumption than the cited bipolar NE555 (vs. NE555)
- Same-family sourcing option retains CMOS timing characteristics (vs. TS555IDT)
Designhinweise
Connect the timing capacitor directly between the THRES and TRIG pins, and keep the timing resistors close to the timer to minimize parasitic capacitance and noise pickup. Route the timer ground return toward the device ground rather than through high-current switching paths. The control pin normally uses a bypass capacitor to ground; follow the manufacturer reference circuit for the recommended value and stability requirements.
Place a local supply-decoupling capacitor close to VCC and provide a low-impedance return to the ground pin. Although the TS555CDT reduces supply-current spikes relative to a bipolar NE555, high-frequency layout still matters. Keep the decoupling loop compact, avoid sharing narrow return paths with motors or relays, and verify supply ripple at the timer pins because voltage variation can affect timing and threshold behavior.
Do not treat every NE555 as an automatic substitute. TS555CDT reaches 2.7 MHz and typically draws 110 µA at 5 V, while the bipolar NE555 comparison cites a 0.1 MHz maximum and 3 mA typical current. Before replacing TS555CDT, verify the SOIC-8 footprint, pin functions, output-drive capability, supply range, maximum frequency, and temperature-grade requirements in the selected component's datasheet.
Compliance-Informationen
The product descriptions identify a CMOS timer and commercial-oriented suffix context but do not explicitly state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.