TS932AIN - Dual 100 kHz Rail-to-Rail Op Amp | STMicroelectronics
Teilenummer: TS932AIN ✗ AbgekündigtTS932AIN Übersicht
An operational amplifier is a voltage-feedback analog IC that compares an amplified error signal with a feedback network to control its output. The TS932AIN belongs to the dual operational amplifier category, combining two amplifier channels in one package. Its rail-to-rail output architecture is useful when signals must remain usable near the available supply limits, while its micropower design suits battery-operated and low-power instrumentation.
The principal features of the TS932AIN include two amplifier circuits, rail-to-rail output, a 100 kHz gain-bandwidth product, and an industrial temperature grade. The 100 kHz bandwidth supports general-purpose low-frequency signal conditioning rather than demanding high-speed waveform applications. The through-hole 8-DIP construction supports prototyping, repair, legacy equipment, and industrial control boards where leaded packages remain convenient to assemble.
The TS932AIN is specified as a general-purpose amplifier rather than a precision or high-voltage part. Because the device uses an 8-pin DIP, it provides two complete amplifier channels with shared supply pins. Designers should verify the manufacturer's pin description and operating limits against the target circuit before substituting it into safety-critical, automotive, or medical equipment.
Typical uses include low-frequency sensor conditioning, current-loop and voltage-amplifier stages, industrial control interfaces, audio preamplification, and portable measurement systems. Its dual-channel configuration can reduce component count when two similar low-frequency signals must be conditioned. The 100 kHz gain-bandwidth rating also makes it appropriate for slow control loops and modest instrumentation bandwidth, rather than pulse or data-conversion applications demanding much higher bandwidth.
For a new design, check input bias current, output swing, supply range, noise, and stability requirements against the manufacturer datasheet before committing to the TS932AIN. Place bypass capacitors close to the supply pins, keep feedback paths compact, and observe the standard dual-op-amp pin arrangement shown below. This page also identifies package and function alternatives while clearly separating true PCB drop-ins from options that require a layout change.
Drop-in-Alternativen für TS932AIN – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Für dieses Produkt sind keine Drop-in-Alternativen verfügbar.
Alternativen anfordernTS932AIN Grenzwerte & elektrische Eigenschaften
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 2 circuits |
| Gain-Bandwidth Product | 100 kHz |
| Output Architecture | Rail-to-rail output |
| Power Class | Micropower operational amplifier |
| Temperature Grade | Industrial |
| Package Type | 8-pin DIP |
| Package Code | DIP |
| Package Shape | Rectangular |
| Montageart | Through-hole |
| Number of Terminals | 8 terminals |
| Number of Amplifier Channels | 2 |
| RoHS-Status | Compliant |
TS932AIN Pin-Konfiguration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN-1 — Amplifier 1 inverting input |
| Pin 3 | IN+1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply |
| Pin 5 | IN+2 — Amplifier 2 non-inverting input |
| Pin 6 | IN-2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | V+ — Positive supply |
Typische Anwendungen
TS932AIN ist geeignet für 6 Anwendungs: Low-Frequency Sensor Conditioning, Industrial Control Signal Interface, Portable Battery-Powered Measurement, Audio Preamplifier Stage, Precision Test and Measurement Front End, Legacy Equipment Repair and Continuation.
Low-Frequency Sensor Conditioning
The TS932AIN fits two-channel sensor conditioning because each package provides two general-purpose operational amplifiers with rail-to-rail output and a 100 kHz gain-bandwidth product. One channel can amplify a sensor signal while the other handles a reference or monitor signal, reducing duplicated components. The 8-pin DIP construction is particularly convenient for industrial instrumentation prototypes and repair boards that use through-hole footprints. Before finalizing the stage, verify the sensor impedance, amplifier input bias current, common-mode range, and output-swing limits in the manufacturer datasheet. The 100 kHz bandwidth is appropriate for slow process variables, resistive sensors, and supervisory signals rather than fast pulse measurement.
Empfohlen
Industrial Control Signal Interface
The dual TS932AIN is useful in industrial control boards that must translate low-level voltage signals into control-system ranges. Its two rail-to-rail-output amplifier channels can be assigned to separate command or feedback paths, while the 100 kHz gain-bandwidth product covers most slow closed-loop and signal-conditioning tasks. The through-hole 8-DIP package simplifies assembly and repair on legacy PLC or instrumentation boards. Designers should confirm the operating voltage, input common-mode range, output capability, and stability with the required feedback network. Industrial qualification also requires checking the exact temperature grade and any application-specific isolation or safety requirements.
Empfohlen
Portable Battery-Powered Measurement
The TS932AIN's micropower operational-amplifier positioning makes it applicable to portable, battery-powered measurement circuits where power consumption and analog conditioning must be balanced. Two amplifier channels can process related sensor outputs without requiring two separate packages, and the 100 kHz gain-bandwidth product is sufficient for many portable health, environmental, and industrial monitoring signals. Rail-to-rail output can improve utilization of limited signal headroom, although actual swing limits depend on the supply and load. Verify quiescent current, input offset, noise, and achievable output range in the manufacturer datasheet before setting battery-life expectations or designing the enclosure and power tree.
Empfohlen
Audio Preamplifier Stage
The TS932AIN can serve in low-level audio preamplifier and buffering paths where two channels must be handled by one dual package. Rail-to-rail output supports use of more of the available signal range, and the 100 kHz gain-bandwidth product is ample for common audio-band conditioning stages. The 8-pin DIP package is useful in prototype audio equipment, educational designs, and legacy amplifier boards where through-hole construction is preferred. Audio performance still depends on input-noise behavior, offset voltage, output drive, and the selected gain network, all of which must be checked in the manufacturer datasheet. Stable feedback layout and adequate supply decoupling are especially important near microphone-level inputs.
Empfohlen
Precision Test and Measurement Front End
The TS932AIN can support low-frequency instrumentation and test-equipment front ends where a dual general-purpose amplifier is needed for excitation, buffering, or gain stages. Its 100 kHz gain-bandwidth product covers many slowly varying measurement channels, and the two channels provide flexibility for processing a sense signal and a reference within one package. The industrial temperature grade supports appropriate equipment categories when the complete operating-range requirements are met. For precision work, engineers must review offset voltage, bias current, noise density, common-mode range, and drift rather than relying on bandwidth alone. The manufacturer datasheet should supply the values needed for error-budget calculations.
Empfohlen
Legacy Equipment Repair and Continuation
The TS932AIN is especially relevant to repairing and maintaining equipment designed around 8-pin through-hole DIP operational amplifiers. The rectangular DIP package, two amplifier channels, and documented general-purpose rail-to-rail function make it a practical candidate for restoring failed analog sections in legacy instrumentation, control, and signal-processing equipment. Before ordering, compare the failed device's pin functions, supply requirements, gain-bandwidth behavior, offset, bias current, and load capability. Because the part is obsolete, request current condition and traceability through the Request a Quote form. For a new board, use the original footprint and verify every electrical limit rather than assuming every dual DIP amplifier is interchangeable.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TS932AIN – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TS932AID | TS932AIDT | LM2902N/PB |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Amplifier Circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
Designhinweise
Use the manufacturer pin-description table when assigning the eight DIP connections. The TS932AIN contains two complete amplifiers but only one pair of supply pins, so both channels share the same positive and negative rails. Keep the two feedback networks separate and route each output only to its intended load. If a board change from DIP to SO-8 is considered, treat it as a layout redesign rather than a drop-in conversion because the lead pattern and body dimensions differ.
Confirm the device's supported supply range and total supply current before selecting the bypass network. Place a suitable low-ESR bypass capacitor close to the positive supply pin and return its ground path directly to the device ground connection. Because the TS932AIN is a dual amplifier, both channels share supply pins; excessive output loading or inadequate rail decoupling can therefore affect both channels simultaneously.
Keep each feedback loop physically short and use the lowest practical source resistance at the non-inverting input. The 100 kHz gain-bandwidth product makes the TS932AIN suitable for slow signals, but high gain combined with excessive parasitic capacitance can reduce stability or alter bandwidth. Check the manufacturer stability guidance for the intended noise gain and keep sensitive input nodes away from output and supply-return paths.
Do not treat every dual 8-pin amplifier as a substitute for the TS932AIN. Rail-to-rail output, 100 kHz bandwidth, micropower operation, input bias, offset, noise, common-mode range, and output swing all affect interchangeability. Also distinguish the through-hole TS932AIN from related surface-mount TS932AID variants; changing package type requires a different PCB land pattern and careful assembly-process review.
Compliance-Informationen
A distributor product listing explicitly identifies the exact TS932AIN as RoHS compliant. No additional compliance declarations are stated for the component.