TS944AIN - Quad Micropower Rail-to-Rail Op Amp | STMicroelectronics
Teilenummer: TS944AIN ✓ AktivTS944AIN Übersicht
An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify small voltage differences. A rail-to-rail output stage can approach the positive and negative supply rails, improving output-voltage range in low-voltage systems. The TS944AIN belongs to the operational-amplifier hierarchy within analog and signal-chain semiconductors, combining four amplifier channels, micropower consumption, and through-hole construction in one package.
The four-channel architecture reduces the number of amplifiers needed for multi-signal conditioning. Each channel offers a typical 10 kHz gain-bandwidth product and 0.0045 V/us slew rate, making the device appropriate for low-frequency buffering, sensor amplification, and general-purpose signal conditioning. Typical input bias current is 1 pA, while typical input offset voltage is 5 mV.
Performance is optimized for low-power rather than high-speed operation. The 10 kHz gain-bandwidth product favors stable operation near unity gain and limits bandwidth in precision measurement stages. The 0.0045 V/us slew rate also means the amplifier requires time to respond to larger output transitions. Its 1.2 uA typical supply current per channel reduces the power budget in portable and always-on equipment.
Typical uses include low-frequency sensor interfaces, battery-powered instrumentation, audio signal conditioning, industrial control inputs, and four-channel acquisition systems. The 14-DIP format is useful for through-hole prototypes, educational circuits, repair work, and industrial assemblies where a socketed or manually inserted package is preferred.
Designers should verify the complete electrical limits, input common-mode range, output swing, supply range, and stability requirements in the STMicroelectronics datasheet before finalizing the circuit. Decoupling capacitors, input bias-current return paths, output loading, and resistor values remain application-dependent and should be selected from the device's recommended operating conditions.
Drop-in-Alternativen für TS944AIN – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit TS944AIN (gleiche Bauform und Footprint) – abweichend in Amplifier Type, Input Offset Voltage, Package, Supply Current.
TS944IN
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →TS944AIN Grenzwerte & elektrische Eigenschaften
| Amplifier Type | General Purpose |
| Number of Circuits | 4 circuits |
| Ausgangstyp | Rail-to-rail |
| Gehäuse | 14-DIP (0.300 in, 7.62 mm) |
| Montageart | Through-hole |
| Versorgungsstrom | 1.2 uA per channel typical |
| Gain Bandwidth Product | 10 kHz |
| Slew Rate | 0.0045 V/us |
| Input Bias Current | 1 pA typical |
| Input Offset Voltage | 5 mV typical |
| Output Current per Channel | 5 mA |
| Terminal Count | 14 terminals |
TS944AIN 14-dip (0.300 in, 7.62 mm) Pinbelegungsleitfaden
Pinbelegung für TS944AIN (14-dip (0.300 in, 7.62 mm)-Gehäuse). Dieses analoge Bauteil verfügt über Eingangs-, Ausgangs- und Versorgungspins. Offset-Null-, Kompensations- und Enable-Pin-Konfigurationen entnehmen Sie dem Herstellerdatenblatt. Ideal für Signalaufbereitung und Verstärkerschaltungen.
Keine detaillierten Pinbelegungsdaten verfügbar für TS944AIN.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
TS944AIN ist geeignet für 6 Anwendungs: Battery-Powered Sensor Conditioning, Industrial Process Measurement, Low-Power Audio Buffering, Portable Medical Monitoring, Test and Measurement Front End, Automotive Low-Speed Control Interface.
Battery-Powered Sensor Conditioning
The TS944AIN fits low-power sensor interfaces because its four channels operate from a supply current of 1.2 uA per channel while providing rail-to-rail outputs. Each amplifier can buffer a high-impedance sensor signal or provide gain before conversion by an ADC. The 10 kHz gain-bandwidth product is appropriate for slow temperature, pressure, and position signals rather than high-speed waveforms. In a battery-powered design, the device helps minimize four-channel signal-path overhead without requiring multiple packages. Confirm the supply range, input common-mode limits, offset contribution, and output-load behavior in the STMicroelectronics datasheet.
Empfohlen
Industrial Process Measurement
The TS944AIN can support four low-frequency industrial measurement channels where compactness and low supply current are important. Its 10 kHz gain-bandwidth product is suitable for buffering slow pressure, level, and temperature signals, while the rail-to-rail output maximizes swing in low-voltage instrumentation systems. Four amplifiers in one 14-DIP package simplify board partitioning when the signal bandwidth is limited. Protection networks, input filtering, grounding, and isolation should be added according to the measured-node environment. Check the common-mode range, offset voltage, output current, and operating-temperature limits before using the device in safety-related or high-noise industrial circuits.
Empfohlen
Low-Power Audio Buffering
The TS944AIN is suitable for low-frequency audio buffering when the design prioritizes low supply current and rail-to-rail output swing. Its four channels can handle stereo differential or single-ended signal paths, and the 0.0045 V/us slew rate accommodates general-purpose audio functions with conservative bandwidth requirements. Because the gain-bandwidth product is only 10 kHz, the device is better suited to audio-frequency signal routing and general conditioning than demanding wideband audio paths. Layout should keep input traces away from switching nodes, provide local supply bypassing, and confirm that the output can drive the intended load without violating the datasheet limits.
Empfohlen
Portable Medical Monitoring
The TS944AIN is a candidate for portable monitoring equipment that conditions several low-frequency physiological or environmental sensors. Its four amplifier channels and 1.2 uA typical supply current per channel help conserve battery capacity, while rail-to-rail outputs improve signal utilization at low supply voltages. The 10 kHz gain-bandwidth product fits slow biopotential or sensor-trend signals rather than wideband acquisition. In medical instrumentation, the signal-chain accuracy, isolation strategy, protection level, and applicable quality requirements must be evaluated independently; the amplifier itself does not establish medical certification. Validate offset, noise, common-mode range, and patient-circuit protection at the system level.
Empfohlen
Test and Measurement Front End
The TS944AIN can provide four general-purpose buffers or amplifiers ahead of slow measurement circuits in laboratory and field-test equipment. The 14-DIP package is convenient for prototypes, manual assembly, and repairable through-hole boards, while four channels reduce the number of discrete amplifier packages. The 10 kHz gain-bandwidth product and 5 mV typical input offset voltage set practical expectations for low-frequency measurements rather than precision instrumentation. High-impedance sources need a suitable bias-current return path, and grounding must be arranged to avoid injecting errors into the measured signal. Confirm output settling, loading, and noise behavior against the intended bandwidth.
Empfohlen
Automotive Low-Speed Control Interface
The TS944AIN may be considered for non-safety-critical, low-speed automotive interface circuits when its electrical and temperature limits are verified for the vehicle environment. Four rail-to-rail amplifier channels can condition position, pressure, or switch-status signals, while the 1.2 uA typical supply current per channel supports low quiescent power. The 14-DIP package is primarily suited to prototypes and specialized through-hole assemblies rather than compact automotive modules. Engine-bay applications require careful review of temperature range, transient protection, electromagnetic compatibility, vibration, and qualification. The suffix and ordering information should be checked for the exact deployment requirements before production use.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für TS944AIN – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | TS944IN |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 14-DIP (0.300 in, 7.62 mm) | 14-DIP (0.300 in, 7.62 mm) |
| Number of Amplifier Circuits | 4 | 4 |
| Output Type | Rail-to-rail | Rail-to-rail |
| Supply Current per Channel | 1.2 uA typical | 1.2 uA typical |
| Gain Bandwidth Product | 10 kHz | 10 kHz |
| Slew Rate | 0.0045 V/us | 0.0045 V/us |
| Input Bias Current | 1 pA typical | 1 pA typical |
| Input Offset Voltage | 5 mV typical | 5 mV typical |
| Output Current per Channel | 5 mA | 5 mA |
Wichtigste Unterscheidungsmerkmale
- Four micropower amplifier channels in one through-hole package (vs. TS944IN)
- Rail-to-rail output reduces low-voltage signal-range constraints (vs. TS944IN)
- Very low typical input bias current supports high-impedance signal sources (vs. TS944IN)
- A defined ordering suffix supports exact procurement and qualification control (vs. TS944IN)
Designhinweise
Place a local bypass capacitor close to each supply connection and route return current directly to the device ground. Because the typical current is 1.2 uA per channel, leakage through board contamination, sockets, and protection components can become significant. Use low-leakage diodes where input protection is required, avoid excessive resistive bias networks, and confirm that shutdown or leakage currents remain acceptable for the complete analog system.
Do not select the TS944AIN for signal paths requiring megahertz bandwidth, fast edge capture, or very low input-offset error. Its 10 kHz gain-bandwidth product, 0.0045 V/us slew rate, and 5 mV typical input offset define its practical operating class. Also verify that the source impedance and feedback network do not create excessive noise gain or amplifier instability. The manufacturer gain-bandwidth and stability guidance should be used for final resistor selection.
Keep the 14-DIP footprint on a through-hole board with adequate spacing from high-current switching nodes and motor-drive wiring. Route each amplifier's input and feedback traces away from supply-current edges and digital clock lines. For high-impedance sensors, use a short guarded input path and provide a defined bias-current return voltage. The rail-to-rail output reduces headroom requirements, but it does not remove the need to verify the allowed output swing at the selected supply voltage.
The low 10 kHz gain-bandwidth product generally simplifies stability compared with high-speed amplifiers, but the feedback network still determines noise gain and bandwidth. Check the source impedance against the bias-current and offset requirements, and ensure the load does not force the output outside its permitted current or swing limits. When driving an ADC, place any anti-alias capacitor according to the ADC's acquisition requirements and observe the resulting feedback-network constraints.
Compliance-Informationen
Compliance attributes are not stated in the manufacturer-linked information used for this page. The component is a general-purpose industrial instrumentation amplifier rather than an automotive-qualified ordering variant.