VSC8531XMW-01 - 1-Port Gigabit Copper PHY | Microchip
Teilenummer: VSC8531XMW-01 ✓ AktivVSC8531XMW-01 Übersicht
A copper PHY is an interface integrated circuit that converts data between a digital network processor and physical copper wiring. It belongs to the Ethernet interface IC hierarchy: PHY transceiver, physical-layer device, network interface IC, and semiconductor. The VSC8531XMW-01 combines 10/100/1000BASE-T physical signaling with configurable MAC-facing interfaces, allowing a network processor, router, switch, or embedded system to communicate through standard twisted-pair Ethernet links.
Key features include one Gigabit copper port, RGMII and RMII support, IEEE 802.3az Energy Efficient Ethernet, Wake-on-LAN operation, hardware-configured operating modes, and configurable MAC-interface drive strength. The broad I/O LVCMOS support is useful when the PHY must interface with systems using different logic levels. Hardware configuration is performed by sampling output pins on the rising edge of reset and holding selected pins high or low, reducing the need for complex register initialization in straightforward designs.
The device is designed for space-constrained equipment where a 6 mm x 6 mm surface-mount package is valuable. Its single-row 48-QFN construction supports compact routing while providing separate Ethernet and MAC-side interfaces. According to the Microchip VSC8531-01 datasheet, the device can also operate in systems that power terminal equipment through the twisted pair in accordance with the power-over-Ethernet arrangement described in IEEE 802.3af Clause 33. Exact operating limits, internal clock requirements, and recommended magnetics depend on the selected system configuration.
Typical applications include compact routers, Ethernet switches, industrial control equipment, set-top and network appliances, USB-to-Ethernet products, and embedded systems requiring 10/100/1000BASE-T connectivity. RGMII is appropriate for higher-throughput parallel processor interfaces, while RMII reduces pin count in cost- and power-sensitive embedded designs. Wake-on-LAN can support remote wake-up behavior in network equipment, and Energy Efficient Ethernet can reduce link activity when the traffic load is low.
PCB implementation should follow the manufacturer's hardware design checklist for magnetics, termination, clocking, decoupling, and differential pair routing. Keep the PHY, Ethernet magnetics, and high-speed copper traces close together, provide the specified decoupling capacitors close to their supply pins, and route each differential pair as a controlled-impedance pair with minimal vias. Do not infer the complete pin configuration from a marketplace summary; use the pin-description and layout sections in the manufacturer datasheet before releasing a PCB.
This page organizes the principal device identity, package information, application guidance, comparison points, and design considerations into one engineering-focused reference. It also distinguishes the exact VSC8531XMW-01 order code from related VSC8531 variants so procurement and PCB reuse decisions can be made against the appropriate Microchip ordering information.
Drop-in-Alternativen für VSC8531XMW-01 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit VSC8531XMW-01 (gleiche Bauform und Footprint) – abweichend in MAC Interface, Package, Product Type, Wake-on-LAN.
VSC8531XMW-05
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →VSC8531XMW
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →VSC8531XMW-01 Technische Daten
| Product Type | Single-port Gigabit Ethernet copper PHY |
| Ethernet Port Count | 1 port |
| Maximum Data Rate | 1000 Mbps |
| Supported Ethernet Rates | 10/100/1000BASE-T |
| MAC Interface | RGMII or RMII |
| Energy Efficient Ethernet | IEEE 802.3az EEE |
| Power over Ethernet Support | IEEE 802.3af Clause 33 system compatibility |
| Wake-on-LAN | Supported |
| Interface Logic | LVCMOS |
| Gehäuse | 48-QFN, 6 mm x 6 mm |
| Package Construction | Single-row QFN |
| Terminal Pitch | 0.4 mm |
| Montageart | Surface mount |
| Configuration Method | Hardware strap configuration sampled on rising edge of reset |
| MAC Drive Strength | Configurable |
VSC8531XMW-01 single-row qfn Pinbelegungsleitfaden
Pinbelegung für VSC8531XMW-01 (single-row qfn-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für VSC8531XMW-01.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
VSC8531XMW-01 ist geeignet für 6 Anwendungs: Compact Ethernet Router, Industrial Ethernet Control, USB-to-Ethernet Adapter, Network Appliance, Low-Power IoT Gateway, Set-Top and Media Device.
Compact Ethernet Router
The VSC8531XMW-01 fits a compact router requiring one 10/100/1000BASE-T copper port. Its RGMII interface supports a parallel MAC connection to a network processor at a maximum 1 Gbps physical rate, while RMII can reduce host-interface pin count in lower-complexity designs. The 6 mm x 6 mm 48-QFN package also conserves board area compared with larger Ethernet PHY packages. A practical implementation places the PHY near the RJ45 connector and Ethernet magnetics, then routes the copper pairs as short differential pairs. Configuration straps must be assigned according to the manufacturer reset-sampling requirements, and the clock source must satisfy the selected MAC-interface mode.
Empfohlen
Industrial Ethernet Control
The VSC8531XMW-01 can support an industrial Ethernet control endpoint with one copper network connection. Its 10/100/1000BASE-T support allows interoperability across common industrial and office network speeds, and hardware-configured operating modes help simplify systems that do not need extensive software initialization. The device should be paired with magnetics and isolation components appropriate to the installation's isolation and surge requirements. Engineers should verify the exact operating-temperature limits, creepage requirements, grounding strategy, and conducted-emissions performance for the final enclosure and power architecture before using the PHY in a safety- or mission-critical installation.
Empfohlen
USB-to-Ethernet Adapter
The VSC8531XMW-01 is suitable for a USB-to-Ethernet adapter that needs one gigabit copper port. Its configurable parallel MAC interface can accommodate suitable USB-to-Ethernet controller arrangements, while the 6 mm x 6 mm package helps maintain a compact dongle or USB card form factor. The RGMII path can support higher-throughput traffic, whereas RMII may be preferable for a lower-cost or lower-power host connection. Because adapter boards often rely on a shared USB and Ethernet power source, the implementation must maintain clean PHY, magnetics, and digital supplies with local decoupling close to the relevant pins.
Empfohlen
Network Appliance
The VSC8531XMW-01 is appropriate for a compact network appliance that requires a single wired network connection. The PHY handles copper physical signaling at rates up to 1000 Mbps and offers RGMII or RMII host connectivity, allowing the system architect to match the interface to the application processor. Its single-row 48-QFN package supports dense board layouts, although careful magnetics placement and controlled-impedance routing remain necessary. IEEE 802.3az Energy Efficient Ethernet can reduce activity during low-traffic periods, while Wake-on-LAN supports compatible remote-wakeup functions. The exact power-management behavior should be validated through the manufacturer's register and application guidance.
Empfohlen
Low-Power IoT Gateway
The VSC8531XMW-01 can serve as the wired Ethernet interface in a low-power IoT gateway. The device combines one Gigabit copper port with IEEE 802.3az Energy Efficient Ethernet, allowing the link to reduce signaling activity when traffic is light. Wake-on-LAN can support remote activation when the remote endpoint is configured for that function. The 6 mm x 6 mm 48-QFN package is useful in gateways where connector placement and board area are constrained. Designers should still evaluate total board power, magnetics loss, thermal behavior, and the PHY's clocking configuration, because low-power link operation does not remove the need for correct high-speed layout and supply decoupling.
Empfohlen
Set-Top and Media Device
The VSC8531XMW-01 suits a set-top or media device that needs one Ethernet port for network services and content delivery. A 1 Gbps copper PHY provides a high-bandwidth link for local-network media, while RGMII or RMII lets the design match a selected host processor. The compact 48-QFN package supports space-constrained consumer electronics, and Energy Efficient Ethernet can benefit intermittent-traffic networks. Engineering teams should confirm operating-temperature limits for the enclosure environment and follow the manufacturer hardware checklist for transformer selection, center-tap capacitance, reference-clock routing, and differential-pair geometry to maintain reliable link performance.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für VSC8531XMW-01 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | VSC8531XMW-05 | VSC8531XMW |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 48-QFN (6 mm x 6 mm) | 48-QFN (6 mm x 6 mm) | 48-QFN (6 mm x 6 mm) |
| Port Count | 1 copper port | 1 copper port | 1 copper port |
| Maximum Data Rate | 1000 Mbps | 1000 Mbps | 1000 Mbps |
| Supported Ethernet Rates | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T |
| Order Code | VSC8531XMW-01 | VSC8531XMW-05 | VSC8531XMW |
Wichtigste Unterscheidungsmerkmale
- Combines one Gigabit copper port with both RGMII and RMII host options (vs. VSC8531XMW-05)
- Adds IEEE 802.3az Energy Efficient Ethernet for link-power control (vs. VSC8531XMW)
- Uses a compact single-row surface-mount package (vs. VSC8531XMW-05)
Designhinweise
Follow the VSC8531 Hardware Design Checklist when placing the PHY, magnetics, and RJ45 interface. Position the Ethernet transformer close to the PHY and keep the four copper pairs short, symmetric, and routed as controlled-impedance differential pairs. Minimize vias and keep switching nodes and unrelated high-current paths away from the PHY and magnetics region. The checklist also addresses Auto-MDIX magnetics requirements, which should be resolved before schematic release.
Assign the hardware configuration straps using the datasheet's reset-sampling method and validate every pulled-high or pulled-low state against the intended operating mode. Resistor values, nearby return paths, and the reset transition sequence can determine the final configuration. Check the selected strap against the VSC8531XMW-01 datasheet rather than copying a layout from a different VSC8531 suffix without comparing its ordering information.
Use the manufacturer-recommended supply network and place the required bypass capacitors immediately adjacent to the corresponding VSC8531XMW-01 supply pins. Keep the switching supply, PHY, magnetics, and digital circuitry separated to limit coupling into the Ethernet signal path. Because exact supply-voltage limits and capacitor values are not stated in the accessible product summaries, the final schematic and layout must use the values in the manufacturer datasheet.
Treat the RGMII or RMII interface as a timing-critical parallel bus. Route MAC signals over a continuous reference plane, minimize stubs, and follow the source-synchronous timing requirements in the datasheet. Confirm the required reference clock and its jitter margin with the host controller. Auto-MDIX operation also requires suitable magnetics, so validate the complete PHY-magnetics combination instead of treating the copper interface as a generic digital port.
Compliance-Informationen
The accessible product information does not state the device's RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. IEEE 802.3az and IEEE 802.3af Clause 33 are functional Ethernet references, not product-compliance certifications.