VSC8540XMV-04 - 10/100M Cu PHY | Microchip | Ethernet
Teilenummer: VSC8540XMV-04 ✓ AktivVSC8540XMV-04 Übersicht
A copper PHY, or physical-layer transceiver, is the integrated circuit that translates logical Ethernet data into signals suitable for twisted-pair cabling. In the hierarchy of network semiconductors, a PHY operates below the Ethernet media-access controller: the MAC organizes frames and protocol access, while the PHY manages the physical signaling, line coding, auto-negotiation, and cable connection. The VSC8540XMV-04 therefore belongs to the Ethernet interface and physical-layer transceiver segment of the broader semiconductor market.
The headline capabilities of this device are its single 10/100 Mbps copper channel, 0.95 V and 2.38 V operating rails, and 68-QFN package. Its 10BASE-TX support targets 10 Mbps legacy networks, while 100BASE-TX operation supports Fast Ethernet links. Energy Efficient Ethernet can reduce power consumption when link traffic is low, and Wake-on-LAN allows a connected system to respond when an appropriate network wake event occurs.
Technical integration centers on the combination of low-power PHY operation, Synchronous Ethernet support, FLF2 status indication, and a compact exposed-pad package. Synchronous Ethernet can help maintain synchronized timing for demanding network equipment, while FLF2 indication provides a hardware status signal for link-fault monitoring. The manufacturer datasheet also identifies compatibility with systems that supply power through the MDI or twisted-pair cable under IEEE 802.3af Clause 33, an important consideration for powered-device designs.
Typical uses include industrial Ethernet controllers, EtherCAT equipment, compact network appliances, telecom equipment, and compact communications systems. Its small 8 mm × 8 mm footprint supports designs where board area is limited, while the feature set helps reduce the need for separate link-management or timing circuitry. System designers should still validate magnetics, termination, power sequencing, thermal performance, and signal-integrity margins against the target network environment.
For PCB implementation, follow the manufacturer’s exposed-pad land pattern, thermal-via, and layout guidance. Keep the PHY supply and ground connections compact, provide the specified bypass capacitance at the device pins, and route high-speed copper PHY signals with continuous references and controlled impedance. Treat the exposed pad as both an electrical connection and a thermal path rather than treating it as an optional ground feature.
This product page organizes the manufacturer’s Ethernet PHY information, package details, sourcing path, replacement analysis, and engineering guidance into one practical reference. It highlights how the VSC8540XMV-04 fits compact copper-networking designs while directing engineers to the manufacturer documentation for complete pin assignments, timing limits, magnetic-component recommendations, and layout constraints.
Drop-in-Alternativen für VSC8540XMV-04 – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit VSC8540XMV-04 (gleiche Bauform und Footprint) – abweichend in Energy Efficient Ethernet, Product Type, Synchronous Ethernet, EtherCAT Support, Package.
VSC8540XMV-05
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
VSC8541XMV-05
✅ Drop-In📋 Referenzalternative (nicht im Katalog)
VSC8541XMV-01
✅ Drop-In ⚠️ Spezifikationen ungeprüftPreis auf Anfrage
Datenblatt ansehen →VSC8540XMV-04 Technische Daten
| Product Type | Single-port copper Ethernet PHY |
| Supported Data Rates | 10 Mbps and 100 Mbps |
| Ethernet Mode | 10BASE-TX and 100BASE-TX |
| Core Supply Voltage | 0.95 V |
| I/O Supply Voltage | 2.38 V |
| Channel Count | 1 copper channel |
| Energy Efficient Ethernet | Supported |
| Wake-on-LAN | Supported |
| Synchronous Ethernet | Supported |
| FLF2 Indication | Supported |
| EtherCAT Support | Supported |
| Gehäuse | 68-QFN, 8 mm × 8 mm |
| Exposed Pad | Present |
| Packaging | Tray |
| Powered Ethernet Compatibility | IEEE 802.3af Clause 33 |
| Maximum Link Rate | 100 Mbps |
VSC8540XMV-04 68-qfn, 8 mm × 8 mm Pinbelegungsleitfaden
Pinbelegung für VSC8540XMV-04 (68-qfn, 8 mm × 8 mm-Gehäuse). Pin-Nummerierung, Funktionen und Anschlussdiagramme sind im Herstellerdatenblatt definiert. Entnehmen Sie diesem den genauen Footprint und Lötrichtlinien.
Keine detaillierten Pinbelegungsdaten verfügbar für VSC8540XMV-04.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
VSC8540XMV-04 ist geeignet für 6 Anwendungs: Compact Industrial Ethernet Equipment, EtherCAT Interface Equipment, Low-Power Network Appliances, Telecom Network Equipment, Powered Ethernet Devices, Embedded Control and Communication Systems.
Compact Industrial Ethernet Equipment
The VSC8540XMV-04 fits compact industrial Ethernet equipment that needs a single 10/100 Mbps copper port without allocating a large PHY footprint. Its 68-QFN 8 mm × 8 mm package includes an exposed pad, allowing the device to serve as the physical-layer interface beneath an Ethernet MAC while consuming little board area. The 0.95 V core and 2.38 V I/O supplies suit platforms that already organize low-voltage digital power separately. Industrial designs should pair the PHY with a qualified magnetic device, implement the manufacturer’s exposed-pad and thermal-via pattern, and verify operation across the complete system temperature range.
Empfohlen
EtherCAT Interface Equipment
Microchip identifies the VSC8540 as a PHY suitable for space-constrained EtherCAT equipment, making the VSC8540XMV-04 appropriate for compact master or slave interface designs. The device handles one 10/100 Mbps copper channel and adds EEE, Wake-on-LAN, Synchronous Ethernet, and FLF2 indication to the basic PHY function set. An EtherCAT implementation must still validate the supported physical layer, timing, clocking, and configuration required by the selected network controller. Keep the PHY-to-MAC interface short, follow the recommended magnetics layout, and test cable startup and link behavior under the intended industrial conditions.
Empfohlen
Low-Power Network Appliances
The VSC8540XMV-04 is appropriate for space-constrained network appliances that expose a Fast Ethernet copper port while limiting board area and power. Its single 10/100 Mbps channel avoids allocating circuitry for unused media rates, and Energy Efficient Ethernet provides a mechanism for reducing link power when traffic is light. Wake-on-LAN can support remote activation after a low-power state, while FLF2 indication assists the host with link-fault handling. The system designer should confirm PHY power consumption, sleep behavior, wake timing, and thermal rise in the final enclosure rather than relying on feature names alone.
Empfohlen
Telecom Network Equipment
The VSC8540XMV-04 can serve as the copper front end in telecom equipment requiring one 10/100 Mbps Ethernet management or service port. Synchronous Ethernet is a notable benefit for timing-sensitive equipment, while the 0.95 V core rail and 2.38 V I/O rail support integration with systems partitioned into core and interface power domains. The 68-QFN package keeps the PHY compact but requires careful exposed-pad soldering and thermal-path design. Use the manufacturer reference layout and magnetics guidance, and validate conducted emissions, cable reach, auto-negotiation, and synchronization behavior for the deployment environment.
Empfohlen
Powered Ethernet Devices
The VSC8540XMV-04 is relevant to powered-device designs because the manufacturer datasheet identifies compatibility with systems supplying power through the MDI or twisted-pair cable under IEEE 802.3af Clause 33. A copper PHY with a single 10/100 Mbps channel can serve as the network interface in a compact powered endpoint while the surrounding power-delivery circuit handles isolation and negotiation. Implementation requires the correct isolation components, magnetics, and cable-side power-path architecture. Verify the complete power-delivery design against the applicable clause and do not infer that the PHY alone implements every powered-device function.
Empfohlen
Embedded Control and Communication Systems
The VSC8540XMV-04 fits embedded control systems that need deterministic copper networking for configuration, diagnostics, or supervisory traffic. A 10/100 Mbps PHY supports basic management traffic without imposing the footprint or power requirements of a multi-port transceiver. The host processor or communications controller must initialize the PHY correctly, manage reset and clocking, and implement the required auto-negotiation and link-status behavior. Before layout release, cross-check the exposed-pad geometry, supply decoupling, magnetics spacing, and differential-pair routing against the Microchip hardware guidelines, especially where an embedded enclosure limits heat dissipation.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für VSC8540XMV-04 – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | VSC8540XMV-05 | VSC8541XMV-05 | VSC8541XMV-01 |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) |
Wichtigste Unterscheidungsmerkmale
- Purpose-built compact single-port copper PHY (vs. VSC8541XMV-05)
- Direct VSC8540-family revision option (vs. VSC8540XMV-05)
- Family-level resource availability (vs. VSC8541XMV-01)
Designhinweise
Implement the VSC8540XMV-04 as a complete 68-QFN exposed-pad layout rather than treating the pad as optional. Follow the manufacturer land pattern, place the input and output bypass capacitors close to their associated supply pins, and provide adequate thermal vias beneath the exposed pad. Confirm pad and via geometry against the current Microchip package drawing before fabrication because exposed-pad solder volume strongly affects assembly yield and thermal performance.
Route the PHY-to-MAC and PHY-to-magnetics interfaces as controlled-impedance differential pairs with continuous reference planes and minimal stubs. Keep the magnetics and high-speed copper connections away from noisy switching nodes and maintain the spacing recommended by the manufacturer. Avoid placing test pads or vias in the sensitive differential paths unless their effect on impedance and return loss has been evaluated.
Plan the 0.95 V core and 2.38 V I/O rails as separate, properly sequenced supply domains. Confirm the permitted startup and shutdown relationship in the manufacturer datasheet before assigning power states. Use the specified local bypass capacitance and verify that the exposed pad and thermal-via structure provide adequate heat spreading for the maximum expected operating temperature.
Do not assume that a matching QFN package establishes drop-in compatibility. Before replacing VSC8540XMV-04 with another revision, compare pin names, supply sequencing, clock requirements, register behavior, supported protocols, magnetic-device recommendations, and reset timing. Also verify the operating-temperature grade and any qualification requirements applicable to industrial, telecom, or EtherCAT equipment.
Compliance-Informationen
The manufacturer datasheet identifies compatibility with powered-device systems under IEEE 802.3af Clause 33. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses require confirmation from the current manufacturer product documentation or declaration of compliance.