XC2C64A-7CPG56I - 64-Macrocell 159MHz CPLD | AMD
Teilenummer: XC2C64A-7CPG56I ✗ AbgekündigtXC2C64A-7CPG56I Übersicht
A CPLD is a user-programmable semiconductor that combines macrocell-based logic with a fixed internal interconnect structure. In the semiconductor hierarchy, a CPLD sits between discrete gate arrays and FPGAs: it offers predictable timing, electrically erasable nonvolatile configuration, and relatively simple design flows. The CoolRunner-II architecture provides deterministic routing and SRAM-based configuration, allowing a design to retain its programmed logic without continuous configuration refresh.
The XC2C64A provides 64 macrocells and approximately 1.5K gates, making it suitable for moderate-complexity state machines, bus controllers, address decoding, protocol bridges, and board-level control functions. Its specified 159 MHz operating frequency supports timing designs where system-level propagation delay and clock constraints must remain predictable. The -7 designation identifies its speed grade, while the I suffix identifies the industrial-temperature option.
The device is manufactured in 0.18 μm CMOS technology and operates from a 1.8 V core supply. Its 56-pin CSBGA package supports compact, high-density PCB layouts, but its fine-pitch ball assignment requires careful PCB design, assembly capability, and inspection. Unlike a large FPGA, the XC2C64A is intended for smaller logic functions where low device count, compact packaging, and fast configuration are more important than very high logic density.
Typical uses include industrial controller logic, embedded peripheral interfacing, programmable signal conditioning, sensor aggregation, and compact embedded systems. The device can also implement boot logic, power sequencing, watchdog handling, interrupt arbitration, and communication-interface state machines alongside a host microcontroller. Its 64-macrocell capacity should be checked against the required I/O count, register usage, and logic equations during architecture selection.
PCB implementation should allocate the CSBGA footprint, ball map, power planes, decoupling capacitors, and programming-interface access according to the manufacturer pin description and package drawing. Signal routing must preserve the intended clock topology, while unused inputs require appropriate treatment. Configuration should also be validated for every power state and startup sequence before the design enters production.
This page combines the CoolRunner-II device characteristics, verified technical sources, lifecycle information, package considerations, and same-package replacement guidance to support faster component selection and hardware planning.
Drop-in-Alternativen für XC2C64A-7CPG56I – gleiches Gehäuse, Pin-kompatibel. Bauteile mit anderem Gehäuse, die eine PCB-Überarbeitung erfordern, sind ausgeschlossen.
Varianten dieser Serie
Modelle derselben Serie, die drop-in-kompatibel sind mit XC2C64A-7CPG56I (gleiche Bauform und Footprint) – abweichend in Package, Package Type, User I/O Count, Device Type, Internal Frequency.
XC2C64A-7CPG56C
✅ Drop-InPreis auf Anfrage
Datenblatt ansehen →XC2C64A-6CPG56I
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
XC2C64A-8CPG56I
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
XC2C64A-6CPG56C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
XC2C64A-8CPG56C
✅ Drop-In ⚠️ Spezifikationen ungeprüft📋 Referenzalternative (nicht im Katalog)
XC2C64A-7CPG56I Grenzwerte & elektrische Eigenschaften
| Device Type | CoolRunner-II CPLD |
| Macrocells | 64 macrocells |
| Logic Gates | Approximately 1.5K gates |
| Maximum Operating Frequency | 159 MHz |
| Architecture | 0.18 μm CMOS |
| Core Supply Voltage | 1.8 V |
| Gehäuse | 56-pin CSBGA |
| Package Type | CSBGA, surface mount |
| Speed Grade | -7 |
| Temperature Grade | Industrial |
| Programmable Logic Type | SRAM-based, nonvolatile configuration |
| Logic Hierarchy | Macrocells with fixed interconnect architecture |
| Montageart | Surface mount |
| Manufacturer Data Sheet | DS311 |
| Data Sheet Revision | 2.3 |
XC2C64A-7CPG56I csbga, surface mount Pinbelegungsleitfaden
Pinbelegung für XC2C64A-7CPG56I (csbga, surface mount-Gehäuse). Dieser digitale IC umfasst GPIO, Kommunikationsschnittstellen (UART, SPI, I2C) und Versorgungspins. Alternative Pin-Funktionen und Konfigurationsoptionen entnehmen Sie dem Herstellerdatenblatt. Unverzichtbar für Embedded-System-Design und PCB-Layout.
Keine detaillierten Pinbelegungsdaten verfügbar für XC2C64A-7CPG56I.
Siehe die Datenblatt für die vollständige Pin-Konfiguration.
Typische Anwendungen
XC2C64A-7CPG56I ist geeignet für 6 Anwendungs: Industrial Controller Glue Logic, Embedded Peripheral Interface Bridge, Sensor Aggregation and Signal Routing, Power Sequencing and Startup Control, Communication Protocol State Machine, Programmable Test and Measurement Interface.
Industrial Controller Glue Logic
The XC2C64A-7CPG56I is appropriate when an industrial controller needs deterministic logic between a host processor and discrete peripherals. Its 64 macrocells can implement address decoding, command sequencing, interrupt masking, watchdog handling, and bus timing control without loading the host processor. The specified 159 MHz maximum operating frequency provides useful timing headroom for synchronous control logic, while the industrial-temperature suffix supports equipment with a wider ambient-temperature requirement. Because the device uses a 56-pin CSBGA, the design should provide adequate escape routing, supply decoupling, and assembly-capable PCB geometry.
Empfohlen
Embedded Peripheral Interface Bridge
The XC2C64A-7CPG56I can bridge dissimilar peripheral buses by implementing protocol state machines, level conversion of control signals, and programmable interrupt routing. A 64-macrocell device provides sufficient logic for moderate-width interfaces while retaining a compact 56-pin CSBGA footprint. The 1.8 V supply and 159 MHz maximum operating frequency suit modern low-voltage embedded systems in which interface timing is known and deterministic. Engineers should budget available I/O, verify clock-domain constraints, and avoid assigning timing-critical routes across poorly constrained combinational paths.
Empfohlen
Sensor Aggregation and Signal Routing
The XC2C64A-7CPG56I is useful for compact sensor nodes that require deterministic acquisition control, sensor selection, timing generation, and data-valid signaling. Its macrocell-based architecture can consolidate several small control functions into one programmable device, reducing discrete logic and preserving a compact board area. The 159 MHz specification supports control and communication timing common to sensor hubs, while the industrial-temperature option suits deployed equipment. The implementation must reserve enough user I/O and configure unused pins according to the DS311 pin-description table to prevent unnecessary switching or contention.
Empfohlen
Power Sequencing and Startup Control
The XC2C64A-7CPG56I can implement deterministic power-up sequencing, reset generation, rail-order control, and fault-status reporting in a mixed-signal or embedded system. Its SRAM-based nonvolatile configuration allows programmed control sequences to operate immediately after power is restored, while the specified 159 MHz performance is more than adequate for ordinary sequencing delays and status logic. The design should validate every reset state and startup path, then use the manufacturer package and pin information to assign supply-sensing and enable outputs correctly.
Empfohlen
Communication Protocol State Machine
A compact communications interface can use the XC2C64A-7CPG56I for framing, command parsing, checksum generation, timeout handling, and flow control. Its 64 macrocells and deterministic interconnect are well matched to fixed-format protocols where a microcontroller would otherwise spend substantial code and execution time. The 159 MHz operating-frequency specification supports reasonably fast synchronous protocol logic, while the CSBGA package keeps the footprint compact. Design verification should include worst-case clock skew, reset behavior, idle-bus handling, and pin-state checks during programming.
Empfohlen
Programmable Test and Measurement Interface
The XC2C64A-7CPG56I can implement instrument-control logic such as relay sequencing, range selection, trigger routing, status aggregation, and front-panel bus decoding. Its moderate logic capacity is appropriate for fixed measurement systems that do not require the routing flexibility of an FPGA. The specified 159 MHz maximum operating frequency accommodates common digital-control paths, and the industrial-temperature option supports wider operating environments. Layout engineers should isolate sensitive analog routing from the CPLD, while logic designers should define deterministic test modes and safe states for every measurement path.
Empfohlen
Zusammenfassung der empfohlenen Produkte
Technische Referenzdaten für XC2C64A-7CPG56I – Vergleich, Designhinweise und Compliance-Informationen.
Auswahlhilfe
Vergleich mit Alternativen
| Parameter | Dieses Produkt | XC2C64A-7CPG56C | XC2C64A-6CPG56I | XC2C64A-8CPG56I | XC2C64A-6CPG56C | XC2C64A-8CPG56C |
|---|---|---|---|---|---|---|
| Package | 56-pin CSBGA | 56-pin CSBGA | 56-pin CSBGA | 56-pin CSBGA | 56-pin CSBGA | 56-pin CSBGA |
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells | 64 macrocells |
| Logic Gates | Approximately 1.5K gates | Approximately 1.5K gates | Approximately 1.5K gates | Approximately 1.5K gates | Approximately 1.5K gates | Approximately 1.5K gates |
| Core Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Process Technology | 0.18 μm CMOS | 0.18 μm CMOS | 0.18 μm CMOS | 0.18 μm CMOS | 0.18 μm CMOS | 0.18 μm CMOS |
| Temperature Grade | Industrial | Commercial | Industrial | Industrial | Commercial | Commercial |
| Programmable Architecture | CoolRunner-II SRAM-based nonvolatile configuration | CoolRunner-II SRAM-based nonvolatile configuration | CoolRunner-II SRAM-based nonvolatile configuration | CoolRunner-II SRAM-based nonvolatile configuration | CoolRunner-II SRAM-based nonvolatile configuration | CoolRunner-II SRAM-based nonvolatile configuration |
Wichtigste Unterscheidungsmerkmale
- Industrial-temperature option in the original system footprint (vs. XC2C64A-7CPG56C)
- Target -7 timing grade with a specified 159 MHz maximum frequency (vs. XC2C64A-6CPG56I)
- Industrial-grade replacement without changing package (vs. XC2C64A-8CPG56C)
Designhinweise
Use the exact 56-pin CSBGA footprint, ball map, power assignments, and assembly recommendations in AMD Data Sheet DS311. Place all required decoupling capacitors close to their associated supply balls and provide continuous, low-impedance power and ground planes. The fine-pitch BGA footprint should be reviewed against the PCB fabricator’s minimum line, spacing, via, solder-mask, and inspection capabilities before layout release.
Assign clock, configuration, control, and user I/O signals directly from the DS311 pin-description table. Preserve the intended clock topology, avoid routing timing-critical nets through switch or test pads unless their parasitics have been included in timing analysis, and place programming or configuration access points where they can be reached reliably. Because a complete public ball-name list is not reproduced on this page, do not infer individual ball functions from the package drawing alone.
Do not treat the commercial-grade XC2C64A-7CPG56C as an unqualified industrial substitute for the XC2C64A-7CPG56I, and do not treat different-package XC2C64A variants as drop-in replacements. Also avoid changing speed grade without repeating timing analysis: a numerically higher or lower grade does not automatically satisfy the original clock, setup, hold, and power budget. Confirm programming compatibility, temperature range, package marking, and system timing before substitution.
Compliance-Informationen
The device is described as industrial-grade, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration appears in the cited material. A general-purpose legacy CPLD is treated as not applicable to AEC-Q100 unless an automotive qualification is specifically documented.