Convertidores DC-DC
Productos (770)
NCP1399APDR2G - 600V Half-Bridge Resonant Controller | onsemi
The onsemi NCP1399APDR2G is a high-performance current mode controller for half-bridge resonant converters, integrating two 600 V gate drivers in a 16-pin SOIC package. It supports a wide switching frequency range of 20 kHz to 750 kHz, adaptive dead-time control, and a dedicated PFC front-stage interface, making it well-suited for high-efficiency LLC and other resonant converter topologies. An LLC resonant controller is a specialized power-supply control IC that drives a half-bridge switching stage whose switches feed an LC resonant tank. The tank shapes the current waveform so the MOSFETs switch at zero voltage (ZVS), eliminating switching losses and enabling high-frequency, high-density designs. Controllers such as the NCP1399APDR2G sit within the power-management IC family and are commonly deployed as the secondary-side controller after a PFC front end in TV power supplies, server PSUs, and industrial SMPS modules. Key features of the NCP1399APDR2G include integrated 600 V half-bridge gate drivers that simplify PCB layout and reduce the bill of materials, an adjustable minimum switching frequency with precise dead-time generation, dedicated PFC control output for coordinated front-stage operation, brown-out protection on the high-voltage bulk rail, and comprehensive fault protection (overcurrent, overtemperature, overload, and brown-out). According to the onsemi NCP1399 datasheet, the device also features a skip-mode function for light-load efficiency improvement. Architecturally, the NCP1399APDR2G uses a current-mode control loop with a dedicated feedback input, allowing tight regulation of the resonant tank current. The adaptive dead-time block automatically adjusts the dead time between the high-side and low-side gate drive transitions to minimize body-diode conduction and maximize the ZVS range. The 600 V high-side driver is implemented using a level-shifter with an internal bootstrap clamp, removing the need for an external bootstrap diode in many designs. Typical applications include LCD TV power supplies (>150 W), notebook and laptop adapters, server and telecom SMPS modules, industrial LED drivers, and any high-density isolated DC-DC converter requiring ZVS operation above 100 W. The dedicated PFC output makes it an ideal match for designs requiring energy compliance such as 80 PLUS or ENERGY STAR. When designing with the NCP1399APDR2G, ensure the high-voltage bulk rail is decoupled with at least 1 µF X7R close to the Vbulk pin and follow the PCB layout guidelines for the high-side driver return path. The integrated 600 V drivers eliminate the need for an external gate-drive transformer, but the bootstrap capacitor must be sized correctly for the switching frequency and gate charge of the chosen MOSFETs. This page synthesizes distributor pricing, drop-in alternative recommendations, and practical design notes not found in the manufacturer datasheet alone.
NCP1654BD133R2G - 133 kHz CCM PFC Controller | onsemi
The onsemi NCP1654BD133R2G is a continuous-conduction-mode power factor correction controller with a nominal 133 kHz switching frequency in an 8-pin SOIC package. It is designed to control the power-switch conduction time in fixed-frequency PWM operation using instantaneous inductor-current feedback. The verified distributor listing specifies a 120 kHz to 146 kHz operating range. This controller belongs to the power-factor-correction and AC-DC power-conversion hierarchy, where it helps shape input current and reduce reactive power in boost pre-converter stages. A power factor correction controller is an integrated control IC that regulates the duty cycle and timing of a boost-converter power switch. In a CCM PFC stage, the inductor remains conducting during each switching cycle, and the controller adjusts switch timing from measured current to support near-unity power factor while transferring energy toward the DC output bus. The NCP1654 is intended for compact and robust continuous-conduction-mode step-up pre-converters. The main verified features of NCP1654BD133R2G are its CCM PFC architecture, fixed-frequency PWM operation, 133 kHz nominal switching frequency, 120 kHz to 146 kHz distributor-listed frequency range, and SOIC-8 package. The onsemi product page describes the family as minimizing external components and simplifying PFC implementation. The package and low component count can help reduce board area, but the final design still requires careful validation of inductor selection, current sensing, protection, startup behavior, and mains-side isolation. Its switching frequency affects magnetic-component size, control-loop behavior, switching losses, and electromagnetic-interference requirements. A 133 kHz nominal frequency is generally positioned above low-frequency boost operation for compactness and lower inductor size, but it does not eliminate the need for layout and thermal checks. The controller’s fixed-frequency operation should be compared with the power stage’s maximum switching stress and the inductor ripple-current target during design review. Typical applications include compact server and telecom power supplies, industrial AC-DC front ends, charger front ends, power adapters, and other boost PFC stages operating from rectified AC. The part is appropriate when the design needs a dedicated CCM PFC controller rather than a generic PWM regulator. Its external power switch and passive components must be selected for the actual input voltage, output voltage, output power, switching frequency, and thermal environment. For implementation, place the controller, current-sense network, gate-drive components, and power-stage connections according to the manufacturer datasheet layout guidance. Maintain short high-current switching loops, provide appropriate input and output decoupling, and verify creepage and clearance for the mains-connected front end. Do not treat the distributor frequency snippet as a substitute for the complete electrical limits; missing values should be confirmed in the manufacturer datasheet. This page combines the verified manufacturer description, distributor identity and package information, and practical selection guidance for engineers evaluating the NCP1654 family. It also distinguishes verified facts from parameters that still require datasheet confirmation, helping procurement and design teams make a more reliable decision for compact CCM PFC pre-converters.
NCP3063B - 1.5A Step-Up/Down/Inverting Switching Regulator | onsemi
The onsemi NCP3063B is a monolithic 1.5 A DC-DC switching regulator supporting step-up, step-down, and voltage-inverting topologies in a single IC. Housed in an 8-SOIC package, it integrates a temperature-compensated reference, a duty-cycle controlled oscillator with active current limit, a high-current output switch, and an internal thermal shutdown circuit. The device is a higher-frequency upgrade to the legacy MC34063A / MC33063A family. A switching regulator (sometimes called a SMPS controller or DC-DC converter IC) is a power management device that uses an internal power switch and an external inductor/capacitor network to efficiently convert one DC voltage to another. Switching regulators sit within the power management IC category, between linear regulators (which dissipate excess voltage as heat) and fully modular DC-DC converter modules. They are typically selected when efficiency, output current, or output voltage flexibility are paramount. The NCP3063 specifically targets low-cost step-up, step-down, and inverting converter implementations. The NCP3063B delivers 1.5 A peak switch current with an adjustable output voltage of 1.25 V and supports a wide operating voltage range suitable for single-cell to multi-cell battery inputs. It includes cycle-by-cycle current limiting, internal thermal shutdown, and a duty cycle controlled oscillator. The 8-SOIC surface-mount package provides a compact footprint with standard pin compatibility with the older MC34063A. Architecturally, the device uses a current-mode control loop with a 1.25 V internal reference and an external feedback divider. The oscillator frequency is set by a single timing capacitor, allowing designers to optimize efficiency versus component size. An internal comparator drives a Darlington output stage capable of sinking or sourcing up to 1.5 A peak. Cycle-by-cycle current limit is implemented by sensing the switch emitter voltage against an internal reference. Typical applications include cost-sensitive consumer products, battery-powered portable equipment, LED drivers, and auxiliary supplies in industrial systems. It is particularly attractive as a drop-in upgrade for legacy MC34063A designs where higher switching frequency allows smaller inductors and capacitors. The wide input tolerance also makes it suitable for automotive subsystems running off 12 V or 24 V rails. When designing with the NCP3063B, carefully size the inductor and flyback capacitor to maintain continuous conduction at the minimum load. The thermal pad of the 8-SOIC should be soldered to a copper pour for adequate heat dissipation at high switch currents. Always verify that the peak switch current does not exceed 1.5 A under worst-case conditions. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found on a single distributor or manufacturer page, with all data points cited to either the onsemi datasheet (document NCP3063-D) or the listed data sources.
NCP3135MNTXG - 5A Sync Buck Converter 2.9-5.5V | onsemi
The onsemi NCP3135MNTXG is a fully integrated synchronous buck converter delivering up to 5 A continuous DC load current (6 A instantaneous) from a 2.9 V to 5.5 V input rail, housed in a 16-pin VFQFN exposed-pad (QFN-16 EP) package. It targets 3.3 V and 5 V step-down applications with an adjustable output from 0.6 V to 4.62 V and supports two control modes (FCCM and automatic CCM/DCM) for efficiency-versus-ripple tuning. Integrated high-side and low-side MOSFETs, internal compensation, and a power-good indicator minimize external component count and PCB area. A buck (step-down) DC-DC switching converter is a power management IC that efficiently converts a higher DC input voltage to a lower regulated DC output voltage by rapidly switching an internal MOSFET and smoothing the resulting pulsed waveform through an LC filter. Within the power management hierarchy, it sits above linear regulators (LDOs) in efficiency for large VIN/VOUT deltas but below multi-phase VRMs in current capability. Buck converters are the workhorse topology for distributing intermediate bus voltages (5 V, 3.3 V, 1.8 V, 1.2 V) across nearly every digital and mixed-signal system. The NCP3135MNTXG delivers 5 A continuous / 6 A peak output, operates from 2.9 V to 5.5 V VIN, and adjusts VOUT from 0.6 V to roughly VIN minus dropout. Its selectable FCCM (forced continuous conduction mode) ensures predictable noise/ripple regardless of load, while automatic CCM/DCM mode boosts light-load efficiency by skipping pulses. Internal MOSFETs (high-side + low-side) eliminate external FET selection, and built-in soft-start, power-good, and over-current/thermal protection reduce design risk. The 16-pin QFN exposed pad provides a low thermal resistance path, simplifying board-level thermal management. The architecture uses adaptive on-time (AOT) control with internal feedback compensation, enabling fast transient response without requiring external RC networks. The 5 V tolerant enable pin and power-good output simplify sequencing in multi-rail systems. By integrating both switches and compensation, the NCP3135 family targets designs where small PCB footprint, high efficiency, and minimal external BOM are critical. Typical applications include 5 V and 3.3 V point-of-load regulation in networking switches, FPGA/CPLD core and I/O rails, SSD controller power, set-top box and consumer SoC rails, and distributed bus converters in telecom/datacom cards. It is well suited wherever a single 5 V input must be stepped down to a lower logic rail with high efficiency and tight load regulation. When designing with this device, derate output current based on VIN/VOUT differential and ambient temperature. Ensure the exposed pad is soldered to a sufficient copper pour to keep junction temperature within the SOA. Select input/output ceramic capacitors with low ESR and adequate voltage derating; place the input cap as close as possible to the VIN and GND pins to minimize switching-node ringing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet alone.
NCP3170BDR2G - 3A 18V Sync PWM Buck Converter SOIC-8 | onsemi
The onsemi NCP3170BDR2G is a 3 A synchronous PWM buck (step-down) DC-DC switching regulator operating from 4.5 V to 18 V input and producing adjustable outputs as low as 0.8 V in an 8-pin SOIC (0.154", 3.90 mm width) surface-mount package. It integrates the high-side and low-side MOSFETs to deliver up to 3 A continuous load current at switching frequencies up to 1 MHz, while providing cycle-by-cycle current-mode control for fast transient response and inherent line-voltage feed-forward. A buck (step-down) switching regulator is a type of DC-DC converter that efficiently steps a higher input voltage down to a lower output voltage by rapidly switching an internal power transistor and storing it in an external inductor. It belongs to the broader hierarchy of switched-mode power supplies (SMPS), which also includes boost, buck-boost, and SEPIC topologies. SMPS ICs in turn belong to the power management IC family used to generate stable, efficient rails for downstream analog and digital ICs. Key differentiating features include an internal 0.8 V ±2% reference, internal soft-start, power-good (PG) open-drain output, and internal compensation that minimizes external part count. The NCP3170 family (suffixes A and B) offers 3 A continuous output current, fixed-frequency PWM control for low noise, and a thermal-shutdown protection scheme. The B suffix (NCP3170B) is the 1 MHz switching-frequency option optimized for smaller inductors and capacitors. The architecture is a peak current-mode controller with internal synchronous rectification, eliminating the need for an external Schottky diode. The high-side P-MOSFET (upper switch) and low-side N-MOSFET (lower switch) are integrated, which reduces board area, lowers BOM cost, and improves efficiency at light loads. Cycle-by-cycle current sensing on the high-side MOSFET provides fast overcurrent protection and inherent input voltage feed-forward for good line transient rejection. Typical applications include point-of-load (POL) converters for FPGAs, ASICs, and DSPs, distributed 5 V/12 V bus regulation, networking and telecom card supplies, industrial control and factory-automation boards, and consumer set-top boxes. The 18 V input rating suits 12 V and 15 V rails common in distributed-power architectures. When designing with this part, select the external inductor using the datasheet's L = VOUT / (IOUT × fSW × ΔIL) guideline (e.g., approximately 4.7 µH at 5 VOUT, 1 MHz). Place input/output ceramic capacitors close to the IC and use a star-ground scheme; routing the exposed pad (when present) to a large ground copper pour improves thermal dissipation at full 3 A load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
NCP3231AMNTXG - 25A Synchronous Buck Converter, 4.5-18V | onsemi
The onsemi NCP3231AMNTXG is a high-current, high-efficiency voltage-mode synchronous buck converter that operates from a 4.5 V to 18 V input rail and delivers output voltages as low as 0.6 V at up to 25 A continuous load current, packaged in a 40-pin VFQFN with exposed thermal pad. A buck converter (step-down DC-DC converter) is a switch-mode power supply topology that efficiently converts a higher DC input voltage to a lower DC output voltage by rapidly switching an inductor between charge and discharge phases. Within the broader taxonomy, the NCP3231AMNTXG belongs to the synchronous buck family (where a MOSFET replaces the conventional rectifier diode for higher efficiency), inside the voltage-mode PWM controller category, inside DC-DC switching regulators, inside the power management IC segment of integrated semiconductors. Key specifications include a 4.5 V to 18 V input range, adjustable output from 0.6 V up to roughly 5 V (limited by the 18 V maximum input minus headroom), 25 A continuous output current, and a high-side low-side integrated MOSFET pair that delivers high efficiency without external switches. The 40-pin VFQFN package with an exposed thermal pad supports sustained high-current operation by providing a low thermal-resistance path to PCB copper. The NCP3231A employs voltage-mode control with internal compensation, programmable switching frequency, soft-start, and comprehensive protection features including over-current, over-voltage, under-voltage lockout, and thermal shutdown. The synchronous rectification architecture eliminates the conduction loss of a freewheeling diode and pushes typical full-load efficiency above 90 percent at 12 V input to 1.2 V output, a level that conventional buck controllers cannot match without discrete synchronous FETs. Typical applications include server and telecom point-of-load converters, networking switch and router core rails, FPGA and ASIC power rails, industrial 12 V intermediate bus converters, and high-current distributed DC-DC POL modules. The 25 A capability is well suited to powering multi-core processors, DDR memory banks, and high-performance DSPs directly from a 12 V bus. When designing with this part, allocate substantial PCB copper area beneath the exposed pad to keep junction temperature within the safe operating area at 25 A, and follow the manufacturer's recommended input/output inductor and capacitor selection for the chosen switching frequency. Use the soft-start and enable pins to sequence multiple NCP3231AMNTXG rails in a multi-rail system. This page synthesizes distributor pricing, drop-in same-brand variants, and practical design notes that consolidate information normally scattered across the onsemi datasheet, distributor listings, and application notes.
NCP43080DMTTWG - Secondary-Side SR Controller | onsemi
The onsemi NCP43080DMTTWG is a secondary-side synchronous-rectifier controller for switched-mode power supplies, with an 8-WDFN 2 x 2 mm package. It is designed for flyback, quasi-resonant flyback, and LLC power-converter topologies. The controller coordinates an external synchronous-rectification MOSFET so that rectification losses can be reduced compared with a conventional diode rectifier. Its key documented functions include externally adjustable minimum off-time and on-time blanking periods, flexible support for different MOSFET packages and PCB layouts, and operation intended to provide reliable, low-noise synchronous-rectifier control. A synchronous-rectifier controller is a power-management IC used in the secondary circuit of an isolated or non-isolated offline power supply. Instead of allowing a diode to conduct during the secondary rectification interval, the controller drives an external MOSFET to act as a low-loss rectifier. The controller belongs to the broader sequence of switch-mode power-supply components: transformer or inductor energy transfer, primary switching, secondary rectification, output filtering, and regulated feedback. The NCP43080 family targets applications where efficiency and secondary-side behavior are important. Its blanking controls help prevent unwanted MOSFET turn-on or turn-off during switching transitions. These protections are especially relevant when leakage currents, ringing, transformer reset behavior, or differing MOSFET switching speeds could otherwise cause false gate-drive pulses. The exact electrical ratings, timing limits, pin names, and recommended external components require confirmation from the manufacturer datasheet and the selected transformer and MOSFET design. Typical implementation targets include isolated flyback chargers, quasi-resonant flyback adapters, power supplies for consumer electronics, and LLC converter secondary stages. The controller is especially relevant where a Schottky diode would otherwise dissipate significant power at high output current. The external MOSFET selection must be coordinated with output voltage, current, switching frequency, transformer reset behavior, gate-drive requirements, and thermal conditions. The principal design consideration is timing coordination between the primary switch and the secondary synchronous MOSFET. Minimum off-time, minimum on-time, propagation behavior, dead time, and layout parasitics determine whether the replacement can improve efficiency without introducing cross-conduction or shoot-through. The package must be placed according to the datasheet layout guidance, with attention to high-current source and return paths, gate-loop inductance, and thermal dissipation. This product page combines the verified onsemi product identity, distributor package information, the official NCP43080 datasheet link, and practical design guidance. Unavailable ratings and package details are intentionally marked for verification rather than inferred from generic controller families.
NCP4308DDR2G - 35V Synchronous Rectifier Controller | onsemi
The onsemi NCP4308DDR2G is a synchronous rectifier controller for switch-mode power supplies, with a 4 V to 35 V operating range, a 1 MHz switching frequency, and an SOIC-8 package. It supports secondary-side synchronous rectification in flyback, quasi-resonant flyback, and LLC power-conversion systems. Its 8 A current capability and adjustable blanking functions help accommodate different synchronous-rectifier MOSFET package types and circuit layouts. A synchronous rectifier controller is a power-management semiconductor that drives an external MOSFET on the secondary side of an isolated or non-isolated switching converter. By replacing diode conduction with low-loss MOSFET switching, it can reduce power loss during output-current transfer. The NCP4308 family belongs to the secondary-side controller, power-management IC, and switch-mode power-supply hierarchy. Key features include externally adjustable minimum off-time and on-time blanking periods, operation across discontinuous-conduction, continuous-conduction, and quasi-resonant flyback modes, and a 1 MHz switching-frequency capability. The controller is designed to provide reliable and low-noise operation of the synchronous-rectifier system while allowing the power stage to be tailored to the transformer, MOSFET, and PCB layout. The NCP4308 architecture coordinates gate timing with the secondary-side waveform. The adjustable timing features help prevent premature MOSFET turn-on or turn-off during ringing and transition intervals. Designers must still validate the timing window against the actual transformer reset behavior, MOSFET gate charge, leakage current, and operating frequency rather than treating the timing values as universal constants. Typical uses include AC-DC adapters, offline power supplies, flyback converters, quasi-resonant flyback converters, LLC converters, USB power supplies, and industrial power modules. In each case, the controller is paired with external synchronous-rectifier MOSFETs rather than acting as the primary-side converter controller. A key design consideration is maintaining adequate separation between the controller and high-current secondary-side switching nodes. Use the manufacturer’s recommended layout, minimize gate-loop area, place timing components close to their pins, and verify dead time, ringing, and cross-conduction behavior with an oscilloscope across the full input and load range.
NCP81111MNI3TXG - 3-Phase VR12.5/12.6 Digital Controller | onsemi
The onsemi NCP81111MNI3TXG is a high-performance, single-output, three-phase digital buck controller compliant with Intel VR12.5 and VR12.6 specifications, supplied in a 32-pin QFN (5x5 mm) package with exposed thermal pad. The device integrates a Serial VID (SVID) interface and an I2C control port, and operates at switching frequencies up to 5 MHz to support compact CPU core-voltage regulator solutions. A multiphase buck controller is a power-management IC (PMIC) that interleaves multiple synchronous buck phases to deliver high current at low voltage while spreading thermal dissipation across the PCB. Within the broader system hierarchy, the NCP81111 sits in the CPU core rail of a server, workstation, or embedded computing platform, between a 12 V (or higher) intermediate bus and the loadline-regulated Vcore output demanded by an Intel VR12.5/12.6 processor. The architecture combines precision analog current sensing with digital modulation to meet the stringent dynamic load, overshoot, and DC tolerance requirements of modern CPUs. Key features include three integrated gate drivers capable of driving external N-channel MOSFETs in a true multiphase topology, SVID bus communication for direct CPU-to-controller command, an I2C interface for telemetry, configuration, and fault readback, per-phase current balancing, dynamic phase add/drop, programmable loadline, and comprehensive protection including over-voltage, under-voltage, over-current, and over-temperature. The controller supports PMBus-compatible telemetry of output voltage, current, and temperature for system-level monitoring. The NCP81111 implements a digital control loop with adaptive voltage positioning and high-bandwidth error amplification, achieving fast transient response to VR12.5/12.6 step loads. Phase shedding dynamically disables phases at light load to maximize efficiency, while automatic phase add/drop maintains regulation under sudden load increases. The 5 MHz switching capability enables the use of small inductors and ceramic output capacitors, reducing board area compared to legacy controllers. Typical applications include Intel VR12.5/12.6-compliant server and workstation CPU core power, single-rail high-current POL converters in networking ASICs and FPGAs, graphics processor power in workstation add-in cards, and high-end embedded computing platforms. The exposed pad package supports sustained multiphase operation at tens of amps with appropriate thermal design. When designing with the NCP81111, follow the manufacturer's reference layout for the QFN exposed pad and place the current-sense resistors and bootstrap capacitors as close as possible to the controller pins. The SVID and I2C lines require pull-up resistors per the Intel VR12.5/12.6 design guide; verify timing with the target CPU's VR12.5/12.6 compliance checklist before tape-out.
NCP81269MNTXG - Synchronous Buck Controller, 2-Bit VID | onsemi
The onsemi NCP81269MNTXG is a synchronous buck controller with 2-bit VID inputs, optimized for converting battery or adapter voltage into the power supply rails required in notebook and desktop systems. Housed in a 20-pin QFN (HVQCCN) package, it features a switching frequency up to 600 kHz, automotive temperature grade support up to 125 °C, and dynamic slew-rate-controlled output voltages. A synchronous buck controller is a type of DC-DC switching controller that uses two MOSFETs in a half-bridge configuration to step down a DC input voltage to a lower regulated DC output. Compared to an asynchronous buck (diode-rectified), the synchronous topology replaces the Schottky rectifier with a low-RDS(on) MOSFET, which significantly improves efficiency at light-to-medium loads and reduces conduction losses. Synchronous buck controllers belong to the broader family of switching regulators (buck, boost, buck-boost), which themselves fall under the power management IC (PMIC) hierarchy for computing and portable platforms. Key features include a 2-bit VID (voltage identification) interface that allows dynamic output voltage slewing for power-state transitions (P-state, VID-based power management in modern CPUs and GPUs), an externally programmable soft-start via a single capacitor, and wide input voltage tolerance suitable for both battery and adapter operation. The 600 kHz switching frequency enables compact inductor selection, while the automotive temperature grade supports harsh-environment deployment. Technically, the NCP81269 integrates high-side and low-side MOSFET drivers, a fixed-frequency voltage-mode control loop, and the VID decoding logic directly on-chip. The 2-bit VID scheme provides four discrete output voltage setpoints selected by external logic inputs, allowing the system controller to command voltage changes for low-power states without software intervention. This makes the controller well suited to CPU/GPU core rails, chipset power, and DDR memory termination rails in space-constrained notebook platforms. Typical applications include notebook system rails, desktop motherboard buck rails, chipset and memory termination supplies, and embedded computing platforms requiring dynamic voltage scaling. The wide operating temperature range and automotive grade make it attractive for industrial and automotive infotainment boards that demand similar power-rail architectures. When designing with this controller, ensure the bootstrap capacitor is sized per the high-side driver's requirements and that the feedback compensation network is matched to the selected output L-C filter. The 2-bit VID inputs are referenced to the controller's logic supply; verify logic-level thresholds match the driving GPIO or system controller outputs. This page synthesizes distributor pricing, drop-in alternative guidance, and practical design notes drawn from manufacturer datasheet material - providing added engineering context not found in the original datasheet.
NCV1362ABDR2G - 50W Automotive QR Flyback Controller | onsemi
The onsemi NCV1362ABDR2G is a highly integrated quasi-resonant (QR) peak current-mode primary-side flyback controller targeting low-power off-line Switch-Mode Power Supplies (SMPS) from a few watts up to 50 W in automotive and commercial applications. Housed in an 8-pin SOIC (SOIC-8 / NB / 8-SOIC) package, the device operates with a switching frequency range of 1 kHz to 140 kHz (typical 110 kHz), a maximum switching frequency of 130 kHz, and is powered from a 6.5 V to 28 V supply on the VCC pin. A quasi-resonant flyback controller is a type of AC-DC offline switching controller that turns the primary MOSFET on when the drain voltage rings to its valley, dramatically lowering switching losses and EMI versus a hard-switched PWM controller at fixed frequency. It belongs to the controller hierarchy: AC-DC controller -> offline switcher -> quasi-resonant controller -> peak current-mode controller -> power management IC. Primary-side regulation (PSR) eliminates the opto-coupler and secondary reference, enabling tighter CV/CC accuracy with a smaller BOM. Key features of the NCV1362ABDR2G include quasi-resonant valley-switching for reduced EMI and improved efficiency, primary-side constant-voltage and constant-current regulation (no opto-coupler required), a wide VCC range of 6.5 V to 28 V, built-in protections (over-voltage, over-current, over-power, short-circuit, and thermal shutdown), and a 1 kHz to 140 kHz programmable switching-frequency range. Automotive-grade qualification per onsemi's NCV prefix supports AEC-Q100 applications such as USB chargers, e-bike chargers, and LED drivers. The controller uses a current-mode control architecture with a transconductance error amplifier and an internal reference, allowing the designer to set loop dynamics with a single external compensation network on the COMP pin. The quasi-resonant detection block identifies the drain-voltage valley and synchronizes turn-on, lowering dv/dt stress on the MOSFET and reducing conducted EMI by up to 10 dB relative to a fixed-frequency controller at the same load. Typical end uses include USB Type-C chargers (5 V / 3 A) for vehicles, 12 V-24 V auxiliary supplies in two-wheeler and four-wheeler electrical systems, LED driver front-stages, e-bike and e-scooter chargers, white-goods auxiliary supplies, and industrial IoT gateways requiring isolated low-power rails. The wide VCC tolerance also allows direct operation from rectified 12 V or 24 V battery buses without an external regulator. When designing with the NCV1362ABDR2G, place the gate-drive resistor and the current-sense resistor as close to the CS and DRV pins as possible, and keep the high-voltage drain loop area minimal to limit ringing that could falsely trigger the QR detector. The VCC hold-up capacitance must sustain operation through the auxiliary-winding dropout interval at minimum line voltage.
NCV68261MTWAITBG - Ideal Diode HS NMOS Controller | onsemi
The onsemi NCV68261MTWAITBG is a reverse polarity protection and ideal diode NMOS controller with an optional high side switch function, driving one or two external N-channel MOSFETs from a 6-pin WDFNW (2x2 mm) surface-mount package. It is intended as a lower-loss, lower-forward-voltage replacement for power rectifier diodes and mechanical power switches in automotive power paths. An ideal diode controller is a power-management device that drives an external MOSFET to emulate a diode without the conduction losses of a p-n or Schottky junction. Where a conventional rectifier diode drops roughly 0.5 V to 0.7 V and dissipates significant heat at high current, an ideal diode stage drops only Iload x Rds(on) of the MOSFET, cutting forward-voltage loss by an order of magnitude. In the vehicle power hierarchy - battery feed, reverse-polarity guard, load switch, point-of-load regulator - this part occupies the protection and switching layer, downstream of the fuse box and upstream of the load. Key features include MOSFET gate control driven directly by the state of the Enable pin, support for one or two N-channel MOSFETs in ideal-diode or high-side-switch configurations, and automotive-grade qualification signaled by the NCV prefix. Replacing a mechanical relay or a series Schottky with this controller plus a low-Rds(on) NMOS reduces forward voltage, power dissipation, and hot-swap contact wear in the power distribution path. Technically, the controller senses the anode-cathode orientation across the external MOSFET and adjusts the gate to block reverse current, while the enable input determines ON/OFF state. Because the external MOSFET sets the current rating, designers can scale the same controller from a few amperes to tens of amperes by selecting an appropriate NMOS - a key advantage over fixed-rating protection ICs. Typical applications include automotive battery reverse-polarity protection, 12 V and 24 V power distribution modules, ECU main power feeds, and industrial systems replacing mechanical relays with solid-state switching. The automotive temperature-grade rating suits underhood and body-electronics environments. Design consideration: the forward-drop saving depends entirely on the chosen MOSFET Rds(on); verify gate-drive amplitude and reverse-blocking behavior at cold crank and load-dump conditions before finalizing the BOM. This page synthesizes distributor pricing, functional cross-references, and practical design notes not found in the manufacturer datasheet alone.
NJW4132U2-A - 40V 1.75A Boost Converter IC | Nisshinbo
The Nisshinbo Micro Devices NJW4132U2-A-TE2 is a 45V-tolerant, 1.75A output current boost (step-up) switching regulator IC integrating a 40V power MOSFET in a compact SOT-89-5/6 surface-mount package. It operates from a wide 4.5V to 40V input range and produces an adjustable output from 1V up to ~38V, making it well suited for industrial 24V/28V bus rails and battery-powered systems that must be boosted above the supply voltage. A boost converter (also called a step-up switching regulator) is a switching power topology that uses an inductor, a power switch, and a rectifier diode to deliver an output voltage higher than the input. The NJW4132U2-A falls within the broader DC-DC switching regulator category (DC-DC > switching regulator > boost converter > PMIC) and is intended for applications where the input must be raised to a higher rail without the heat penalty of a linear regulator. Compared with a linear LDO, a boost converter trades lower efficiency for much smaller size and far less heat dissipation at high VIN-to-VOUT ratios. Key features include 45V absolute maximum input rating, 1.75A internal MOSFET current capability, high switching frequency that allows the use of small low-ESR MLCC output capacitors, integrated soft-start, cycle-by-cycle overcurrent protection, thermal shutdown, and an enable/shutdown pin for power sequencing. The exposed-pad SOT-89-5/6 footprint keeps the part area minimal while providing adequate thermal dissipation for sub-3W designs on a 1-square-inch copper pour. Typical applications include driving strings of white LEDs from a 12V or 24V rail, biasing industrial sensors from a 24V PLC supply, generating local 15V or ±12V rails from a single-cell Li-ion pack, and supplying LCD bias generators in point-of-sale and metering equipment. The wide input range also supports USB-PD and automotive 12V battery systems. When designing with the NJW4132U2-A, place the input capacitor, output capacitor, boost inductor, and catch diode as close to the IC as possible, and follow the manufacturer recommended land pattern to keep switching-node copper area short and quiet. Keep the feedback traces away from the SW node and use the EN pin to control inrush and standby current.
NJW4132U2-A-TE2 - 40V 1.75A Boost Converter | Nisshinbo Micro Devices
The Nisshinbo Micro Devices NJW4132U2-A-TE2 is a 45V-tolerant, 1.75A peak-current boost (step-up) switching converter IC with an integrated low-RDS(on) N-channel MOSFET, housed in a compact SOT-89-5/6 surface-mount package. It accepts a wide 4.5V to 40V input range, supports adjustable output voltages from 1V upward (set by external feedback resistor), and operates at high switching frequency with low-ESR MLCC support on the output - making it ideal for space-constrained industrial and automotive subsystems. What is a boost converter? A boost converter is a switching DC-DC converter topology that produces an output voltage higher than its input. In the broader power management hierarchy, it sits under DC-DC converters, which themselves belong to power management ICs (PMICs). Boost converters use an inductor, switch, diode, and output capacitor to store and release energy, achieving efficiencies typically 80-95% that far exceed linear regulators when VIN is significantly below VOUT. Key features of the NJW4132U2-A-TE2 include: 1.75A internal switch current, wide VIN 4.5V to 40V, high-frequency operation enabling small external LC components, MLCC-compatible output, integrated 45V MOSFET for derating transistor strength, built-in overcurrent protection, thermal shutdown, and an enable/standby pin. The SOT-89-5/6 package provides an exposed tab for thermal dissipation and occupies a footprint suitable for handheld and panel-mount designs where board area is at a premium. The NJW4132U2 uses peak-current-mode PWM control with internal compensation, providing stable transient response across line and load variations. The wide 40V input withstand capability allows direct connection to 12V or 24V industrial battery rails, while the high-side drive architecture and internal 45V MOSFET derating protect against inductive switching transients. According to the Nisshinbo Micro Devices datasheet, the converter maintains regulation across the full input range and offers cycle-by-cycle current limiting. Typical applications include industrial 24V bus boost to 36V/48V rails, automotive bias supplies from 12V battery to logic-level rails, LED backlight boost converters for panel displays, and battery-powered portable instruments. The wide input range particularly suits 12V/24V lead-acid battery systems where cold-crank transients and load-dump surges exceed normal operating voltage. When designing with this device, derate the internal MOSFET at high VIN - the 45V rating provides margin against load-dump transients in 24V automotive systems. Place the input capacitor close to the IC and use a Schottky rectifier with low reverse recovery to maximize efficiency. According to the Nisshinbo datasheet, the feedback resistor divider should use 1%-tolerance parts for output voltage accuracy. This page synthesizes distributor pricing, drop-in SOT-89-5 same-brand alternatives (NJW4132U2-B-TE2, NJW4132U2-C-TE2 family variants), and practical design notes not found in the manufacturer datasheet.
NJW4132U2-CT1-TE1 - 45V/1.75A 2MHz Boost Converter | Nisshinbo
The Nisshinbo Micro Devices NJW4132U2-CT1-TE1 is a 45V/1.75A current-mode boost (step-up) switching regulator IC housed in a compact SOT-89-5/6 surface-mount package. It operates from a wide 4.5V to 40V input range, integrates a 45V/1.75A power MOSFET, and switches at a fixed 2.0 MHz oscillation frequency that supports small ceramic output capacitors. The output voltage is externally adjustable, with the standard variant tracking a 1V reference, and the device delivers up to 2.25A of switch current per the distributor catalog listings. A boost (step-up) converter is a type of switching DC-DC converter that produces an output voltage higher than its input voltage. Boost converters belong to the broader switching regulator family, which also includes buck (step-down), buck-boost, and SEPIC topologies. Within the power management hierarchy they sit between the linear regulator (low noise, low VIN-VOUT headroom) and the charge-pump (low power, simple architecture). High-frequency switching regulators like the NJW4132 enable small magnetics and ceramic output capacitors, replacing the bulky electrolytics required by older converters running at 100 kHz to 500 kHz. Key features include the 2 MHz switching frequency that minimizes passive component footprint, integrated 45V power switch that withstands automotive load-dump transients, ceramic output capacitor compatibility for low-ESR designs, and built-in protections (overcurrent, thermal shutdown, undervoltage lockout) per the manufacturer datasheet. The 4.5V to 40V input range covers 5V, 12V, 24V, and 36V industrial bus rails. The NJW4132U2 uses peak-current-mode control architecture with internal slope compensation, providing stable loop response across a wide range of load and line conditions. The 2 MHz oscillator and small SOT-89-5/6 package allow single-sided PCB assembly in space-constrained applications. The high 45V switch rating supplies designs that must ride through load-dump pulses on 12V or 24V automotive buses. Typical applications include bias supplies for LCD/OLED display panels, point-of-load (POL) regulators after a 12V or 24V bus, LED backlight drivers, battery-powered industrial equipment, and energy-harvesting power conditioning. The wide VIN range and small footprint make it particularly attractive for body-electronics and metering end nodes. When designing with this part, ensure the inductor saturation current exceeds the 1.75A peak switch rating, and place input capacitors close to the IC to minimize switching noise. The thermal pad of the SOT-89-5/6 package requires adequate copper to keep junction temperature below the 150C maximum under worst-case load. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, and practical thermal design notes that supplement the manufacturer's datasheet and help shorten the design review path.
PCA9421 - PMIC 2 Buck + 2 LDO I2C, Li-ion | NXP
The NXP PCA9421 is a highly integrated power management IC (PMIC) providing two step-down (buck) DC-DC converters with I2C-programmable output voltages plus two LDO regulators, designed for 5V input operation in low-power microcontroller applications, and available in an HVQFN24 (BS) package and a WLCSP25 (UK) package. A PMIC (Power Management IC) is a specialized voltage regulator and power management device that integrates multiple power conversion stages - typically buck converters, LDOs, load switches, and supervision functions - into a single semiconductor. In the power management hierarchy, a PMIC sits above individual DC-DC converters and linear regulators, replacing several discrete power management ICs with one programmable solution, reducing board area, bill-of-materials count, and overall system cost. Key features of the PCA9421 include its dual buck converter architecture with I2C-programmable output voltages, two integrated LDO regulators for low-noise analog or digital rails, and operation from a 5V adapter or regulated supply as indicated by distributor listings. This level of integration makes the part a full power management solution rather than a single-rail regulator, which is its principal differentiator against discrete buck-plus-LDO combinations. Technically, the PCA9421 belongs to the NXP PCA9420/PCA9421 PMIC family, which NXP targets specifically at low-power microcontroller applications and similar systems powered by Li-ion battery and/or a 5V adapter in non-portable applications. The I2C interface allows a host microcontroller to adjust buck output voltages dynamically, supporting dynamic voltage scaling and power-mode sequencing in embedded designs. The two package options - HVQFN24 (BS suffix) and WLCSP25 (UK suffix) - give designers a choice between a hand-inspectable QFN footprint and an ultra-compact wafer-level chip-scale package for space-constrained boards. Typical applications include low-power microcontroller power supplies, battery-powered IoT sensor nodes, portable and non-portable devices powered by Li-ion cells or 5V adapters, and general embedded systems requiring multiple sequenced voltage rails from a single input. When designing with the PCA9421, consult the NXP datasheet for the exact buck and LDO current limits, programmable output voltage ranges, and I2C register map, and verify thermal performance for the chosen package option before finalizing the PCB layout. This page synthesizes distributor pricing context, same-family drop-in alternatives, application guidance, and design notes that go beyond the information available on the manufacturer datasheet alone, providing engineers with a consolidated selection resource.
PCA9421BSZ - PMIC 2 Buck + 2 LDO for i.MX RT | NXP
The NXP Semiconductors PCA9421BSZ is a highly integrated power management IC (PMIC) for low-power microcontroller applications, integrating two buck converters and two LDO regulators with programmable output voltages in a 5x5 mm HVQFN-32 package. It is designed to provide a complete power management solution for i.MX RT crossover MCUs and similar low-power processors powered from a Li-ion battery or a 5 V adapter. A PMIC (power management integrated circuit) is a semiconductor device that consolidates multiple power conversion and regulation functions - such as buck converters, LDOs, battery chargers, and power sequencing logic - into a single package. In the power management hierarchy, the PMIC sits between the system power source (battery or adapter) and the load devices (MCU core, I/O, memory, analog rails), replacing several discrete regulators and reducing board area, BOM count, and design complexity. The PCA9421BSZ integrates two high-efficiency buck converters and two low-noise LDOs with programmable output voltage ranges, enabling dynamic voltage scaling for low-power MCU cores. The device supports a 5 V input and is optimized for i.MX RT power domains, providing the core, I/O, and analog rails required by these processors. Its I2C-compatible control interface allows runtime voltage adjustment and power state management, which is essential for battery-powered systems that must balance performance against power consumption. Typical applications include i.MX RT-based industrial controllers, portable medical devices, battery-powered IoT edge nodes, and handheld instrumentation. The integrated bucks deliver high efficiency at moderate load currents, while the LDOs supply noise-sensitive analog and I/O rails. The compact HVQFN-32 package with exposed pad supports thermal dissipation in space-constrained designs. When designing with the PCA9421BSZ, pay close attention to inductor selection for the buck converters, input and output capacitor placement, and the thermal pad soldering to the PCB ground plane. The programmable output voltages must be configured through the I2C interface during initialization, so firmware sequencing must match the MCU power-up requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a single reference for selection, comparison, and layout decisions.
PCA9421BSZ - PMIC, 2 Buck + 2 LDO, I2C | NXP
The NXP Semiconductors PCA9421BSZ is a highly integrated Power Management IC (PMIC) delivering a complete power solution for low-power microcontroller applications, with two step-down (buck) DC-DC converters and two low-dropout regulators (LDOs) in a 24-pin HVQFN package. It is designed for systems powered by a Li-ion battery and/or a 5 V adapter, including non-portable adapter-powered applications. A PMIC (Power Management IC) is an integrated circuit that consolidates multiple voltage regulators, power sequencing, and control functions into a single device. Within the power-management hierarchy, a PMIC sits above discrete DC-DC converters and LDOs, replacing several components with one programmable, space-saving part. This reduces board area, bill-of-materials count, and design risk in battery-powered embedded systems. Key features of the PCA9421 include two buck converters with I2C-programmable output voltage, allowing the firmware to scale MCU core rails dynamically for power optimization, plus two LDOs for low-noise analog or always-on domains. The device integrates power path management for Li-ion battery and 5 V adapter inputs, supporting seamless transitions between power sources. High integration makes it a natural companion for NXP i.MX RT crossover MCUs and other low-power microcontroller systems. Architecturally, the PCA9420/PCA9421 family shares a common platform: the bucks provide the main processor core and I/O rails, while the LDOs supply analog, PLL, or real-time-clock domains. I2C control enables runtime configuration of rail voltages, enable states, and sequencing, which is essential for multi-rail processors that require specific power-up and power-down order. Typical applications include battery-powered IoT sensor nodes, wearable devices, portable medical accessories, and industrial wireless endpoints built around i.MX RT or similar low-power MCUs. The dual-input (battery/5 V adapter) topology also suits smart-home devices and USB-adapter-powered accessories. When designing with the PCA9421, verify buck inductor selection and LDO headroom against the actual load currents in the manufacturer datasheet, and implement the recommended I2C configuration early in firmware bring-up since rail voltages default to programmable states rather than hard-wired dividers. This page synthesizes verified distributor listings, the official NXP datasheet, drop-in family alternatives, and practical design guidance not found together on any single manufacturer or distributor page.
PCA9452 - Automotive PMIC for i.MX 93, 6 Buck + 5 LDO | NXP
The NXP Semiconductors PCA9452 is a single-chip AEC-Q100 grade 2 automotive power management IC (PMIC) specifically designed to support the i.MX 93x family application processors in automotive applications. It integrates six high-efficiency step-down (buck) regulators, five LDOs, one 400 mA load switch, a 2-channel level translator, and a 32.768 kHz crystal oscillator driver, delivering up to 11 regulated outputs from a 5 V supply. A power management IC (PMIC) is a highly integrated power-management device that combines multiple voltage regulators, switches, and supervision functions into a single die, forming the core of the power tree in processor-based systems. Within the power management IC hierarchy, the PCA9452 sits above discrete DC-DC converters and LDOs, replacing a multi-chip regulator solution with one I2C-controllable device, reducing board area, BOM count, and sequencing complexity. Key features include six synchronous buck converters optimized for high efficiency at the core and memory rails of the i.MX 93, five low-dropout regulators for analog, I/O, and PLL supplies, and a 400 mA integrated load switch for peripherals. Control is provided over an I2C-bus interface supporting Standard-mode (100 kbit/s), Fast-mode (400 kbit/s), and Fast-mode plus (1 Mbit/s) data transfers, per NXP UM10204. Architecturally, the PCA9452 integrates the complete power tree required by the i.MX 93x: processor core, GPU/NPU, DDR memory, and peripheral rails, with programmable sequencing and I2C-adjustable output voltage levels. The integrated 2-bit auto-direction-sensing level translator and 32.768 kHz oscillator driver remove two additional external components from typical automotive designs. Typical applications include Driver Monitoring Systems (DMS), occupant monitoring systems, cost-optimized automotive gateways, and automotive infotainment with audio and speech recognition, all operating over the -40C to +105C automotive ambient range. Design consideration: because the six bucks set the i.MX 93 core and DDR voltages, follow the NXP-recommended default I2C register sequence and power-up ordering precisely; incorrect sequencing can prevent processor boot. This page synthesizes verified manufacturer data, distributor listings, pricing tiers, and drop-in variant guidance not consolidated in the NXP datasheet.
PCA9452AHNMP - PMIC for i.MX 93, 6 Buck + 5 LDO | NXP
The NXP PCA9452AHNMP is an AEC-Q100 Grade 2 automotive single-chip power management IC (PMIC) designed to support the i.MX 93x family of application processors, providing six high-efficiency step-down (buck) regulators, five LDOs, one 400 mA load switch, a 2-channel level translator, and a 32.768 kHz crystal oscillator driver, delivering 11 regulated outputs in a compact HVQFN package. A power management IC (PMIC) is a highly integrated power subsystem that combines multiple DC-DC converters and linear regulators on one die, replacing a dozen discrete regulator ICs. In the power-management hierarchy, the PMIC sits above individual voltage regulators and below the system controller, offering sequenced power-up, I2C-bus programmability, and protection functions tailored to a specific processor family such as the NXP i.MX application processors. Key differentiating features include three buck converters that support dynamic voltage scaling (DVS) for the i.MX 93 core rails, allowing the software to trade processor frequency against power consumption; a 400 mA integrated load switch for peripheral power domains; and interrupt-driven supervision via the IRQ_B pin, which asserts LOW on any unmasked interrupt status change and releases HIGH after the application processor reads the INT1 register. The PCA9452 communicates over an I2C-bus interface supporting Standard-mode (100 kbit/s), Fast-mode (400 kbit/s), and Fast-mode plus (1 Mbit/s) transfers. The I2C address at Power-On Reset is defined in Table 17 of the manufacturer datasheet, enabling multi-PMIC systems without address conflicts. The oscillator driver section supports an external 32.768 kHz crystal for the processor's real-time clock domain, and the 2-channel level translator bridges rail domains of different voltages in the i.MX 93 power tree. Typical applications include automotive infotainment and cluster displays based on the i.MX 93, extended-industrial HMI panels, edge-AI gateways, and battery-backed telematics units, all of which need precisely sequenced, low-quiescent-power rails. The single-chip approach reduces board area, BOM count, and total power-tree design risk compared with discrete regulator stacks. A key design consideration is buck inductor selection and layout: the DVS-capable bucks change their target output voltage under software control, so compensation and output capacitance must be chosen per the manufacturer datasheet reference design to keep transient response within processor specification during frequency transitions. This page synthesizes distributor availability from DigiKey, Mouser, Newark and Octopart, lifecycle status, alternatives guidance, and practical design notes not consolidated in the manufacturer datasheet.
PCA9460 - 13-Channel PMIC for i.MX 8ULP, 42-WLCSP | NXP
The NXP PCA9460 is a 13-channel single-chip power management IC (PMIC) delivering four high-efficiency 1 A step-down (buck) regulators, five LDOs (four VLDOs plus one SVVS LDO), and four 150 mohm load switches in a compact 42-ball WLCSP (WSCSP42) package measuring just 2.86 x 2.46 mm. It is purpose-built to be paired with the NXP i.MX 8ULP processor family for ultra-low-power applications. A PMIC (power management integrated circuit) is a highly integrated power management device that consolidates multiple voltage regulators, load switches, sequencing logic, and control interfaces into a single die. In the power-system hierarchy, it sits above individual DC-DC converters and LDOs, providing complete multi-rail power solutions that reduce board area, bill-of-materials count, and overall system quiescent power in processor-based designs. Key features include the four 1 A bucks with high conversion efficiency for core and I/O rails, four dedicated VLDOs for low-noise analog and memory rails, an SVVS LDO for the FlexIO/DPHY supply domain of the i.MX 8ULP, and four integrated 150 mohm load switches for peripheral power gating. Per NXP, the device is optimized where standby power and PMIC power consumption are critical design constraints. Architecturally, the PCA9460 provides predefined power-tree configurations (PCA9460A/B/C variants) matched to i.MX 8ULP boot and sleep modes, with I2C-based control for dynamic voltage scaling and power sequencing. This removes the need for external sequencing CPLDs or supervisor circuitry, trimming both board area and deep-sleep leakage. Typical applications include smart home devices, building safety and security systems, wearables, and smart and medium appliances, where small size, high efficiency, and minimal standby current directly determine battery life and compliance targets. Design consideration: the WLCSP-42 ball pitch demands microvia and blind-via PCB fabrication capability; engineers needing standard via rules should evaluate alternate packaging, as discussed on the NXP Community forums. This page synthesizes distributor availability data, same-family drop-in variants, and practical design notes not found in the manufacturer datasheet.
PD70210ILD-TR - 802.3at PoE PD Controller with 0.3 Ohm FET | Microchip
The Microchip Technology PD70210ILD-TR is a single-channel IEEE 802.3at (PoE+) and 802.3af (PoE) Powered Device (PD) front-end interface controller with an integrated 0.3 ohm power MOSFET, housed in a 16-pin DFN (5x4 mm) package. A Powered Device interface controller is the front-end power-management IC in a Power over Ethernet system. It sits between the Ethernet cable (via the transformer center taps and bridge rectifier) and the isolated DC-DC converter inside the powered device, within the broader hierarchy: PoE PD controller -> power management IC -> semiconductor. It performs the detection, classification, inrush control, and disconnect functions mandated by the IEEE 802.3af and 802.3at standards. Key features include support for IEEE 802.3af, 802.3at, HDBaseT, and general 2-pair or 4-pair power configurations; an internal 0.3 ohm pass FET that eliminates an external external pass transistor; and an advanced classification block supporting 2, 3, 4, and 6 event classification for full 802.3at and Power-over-HDBaseT (PoH) negotiation. The IC identifies, via its SUPP_Sx pins, which of the four cable pairs actually receive power and generates the corresponding flags. An internal bleeder rapidly discharges the input capacitor of the downstream DC-DC converter, ensuring fast re-detection and port power-up when the Ethernet cable is suddenly removed and reinserted into the RJ45 jack. Typical applications include IP security cameras, wireless access points, VoIP phones, HDBaseT extenders, and networked industrial equipment powered over 2-pair or 4-pair PoE infrastructures. The integrated FET and full protection set reduce external component count. Design consideration: verify the classification resistor settings against the downstream DC-DC converter power class so the PSE allocates sufficient power, and confirm inrush capacitor sizing per the IEEE timing windows. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
PEM3024C - 30W PoE+ PD Module, 24V Output | Infomart
The Infomart IT Solutions PEM3024C is a 30W Power over Ethernet Plus (PoE+) Powered Device (PD) module with a 24V isolated output, providing complete compliance with the high-power IEEE 802.3at PoE+ standard while remaining backward-compatible with IEEE 802.3af (PoE) power sourcing equipment. The module extracts power directly from a CAT5 Ethernet cable and is packaged as a compact 14-pin board-mount module. A PoE powered-device module is a type of power extraction and conversion module within the power-over-Ethernet hierarchy: IEEE 802.3at PoE+ system -> powered device (PD) interface -> DC-DC power module -> end equipment. Its role is to perform PD detection, classification, inrush current limiting, and isolation, presenting a regulated DC rail to the host system without any local AC power input. Key features of the PEM3024C include complete IEEE 802.3at compliance for 30W Class 4 power delivery, operation from both PoE+ (802.3at) and PoE (802.3af) PSE sources, a 24V DC output rail suitable for industrial and telemetry electronics, and a 14-pin module footprint that simplifies integration compared to discrete PD controller plus transformer designs. Technically, the module integrates the PD interface physical layer, including the detection and classification signature required by the IEEE 802.3at standard, together with an isolated flyback-style conversion stage that delivers a regulated 24V output at up to 30W. This integration reduces design time and BOM count for Ethernet-powered end nodes. Typical applications cited by distributors include home automation, remote sensors, security and surveillance equipment, telemetry systems, and wireless connectivity nodes - all scenarios where running power over the existing Ethernet drop is more economical than local mains wiring. A key design consideration is thermal management: at full 30W extraction, the module dissipates heat through its PCB mounting, so adequate copper area and airflow around the module are recommended. Verify input cabling is genuine CAT5 or better to minimize DC resistance losses on the power pairs. This page synthesizes distributor availability data, compliance notes, and practical application guidance not found in a single datasheet, providing engineers with consolidated selection information for the PEM3024C PoE+ PD module.
PI3301-00-LGIZ - 36V/10A ZVS Buck SiP Regulator | Vicor
The Vicor PI3301-00-LGIZ is a 36V-input, 3.3V-output, 10A-output ZVS (Zero-Voltage-Switching) buck switching regulator IC integrating the controller, power switches, and all support components inside a high-density 123-BLGA System-in-Package (SiP) module. According to the Vicor manufacturer datasheet, the PI33xx family operates from 8V to 36V input and sustains a fixed/adjustable output range around 2.3V (3.3V nominal) at up to 10A continuous load. The ZVS architecture minimizes switching losses, enabling high-frequency operation that reduces external filter size and maximizes power density for point-of-load DC-DC regulation. A ZVS buck regulator is a synchronous step-down (buck) DC-DC converter topology in which the high-side MOSFET is turned on only when its drain-to-source voltage has fallen to zero, eliminating the overlap of voltage and current during switching transitions. Compared with hard-switched buck regulators, ZVS operation cuts switching losses, lowers EMI, and enables very high switching frequencies (the PI33xx maintains ZVS across the full rated load). Within the broader power conversion hierarchy, the PI3301 sits between discrete buck controllers (e.g. VICOR Chipset PI31xx + PI33xx) and finished PoL modules - it is a System-in-Package that combines magnetics, drivers, and silicon into one reflowable land-grid-array footprint. Key features include 10A continuous output current, 8V to 36V wide input range, a fixed 3.3V output (also adjustable down to 2.3V), and high efficiency across the operating envelope. The 123-BLGA LGA surface-mount package provides a low-profile, lead-free land-grid-array footprint suitable for reflow assembly on standard PCB substrates. Operating junction temperature spans -40C to +125C, allowing deployment in industrial and harsh-environment applications including automotive, industrial automation, and distributed 24V/28V intermediate bus systems. Typical applications include point-of-load regulation from a 24V industrial bus, 28V military/aerospace intermediate bus conversion, telecom/datacom board-level power, and high-density brick-replacement designs. The PI3301-00-LGIZ is also well-suited to fan-out supply stages driving downstream LDO regulators or downstream Vicor ratios in factorized-power architectures, where the ZVS Buck provides a clean 3.3V intermediate rail. When designing with this device, pay attention to the BLGA land pattern and follow Vicor reflow profile recommendations. Use the recommended input bulk capacitance to suppress ripple, and respect the PG/SET/EN signal interface for sequencing. Adequate PCB copper spread beneath the LGA lands is required to dissipate conduction losses and maintain junction temperature within the -40C to +125C range. This page synthesizes distributor stock, official Vicor technical specifications, and cross-reference notes not present in the standalone datasheet, providing a single-citation summary engineers can use during component selection, second-sourcing, and design reviews.