Circuitos integrados

PIC32MX764F128LT-V/PF

PIC32MX764F128LT-V/PF - 32-bit MCU 128KB Flash USB OTG | Microchip

The Microchip PIC32MX764F128LT-V/PF is a 32-bit MIPS M4K microcontroller with 128KB Flash, 32KB SRAM, full-speed USB 2.0 OTG, 10/100 Ethernet MAC, CAN, and 80 MHz CPU clock, housed in a 100-pin TQFP (14x14 mm, PF suffix) package. It integrates a 16-channel 10-bit ADC, multiple UART/SPI/I2C, five 16-bit timers, a 16-bit Parallel Master Port, and a DMA controller, targeting industrial and embedded connectivity designs. The -V temperature grade denotes an operating range of -40 °C to +105 °C, while the trailing L/T indicates the 80 MHz speed grade and tape-and-reel packaging. A 32-bit microcontroller (MCU) is an integrated circuit containing a 32-bit processor core, program memory, data memory, and on-chip peripherals. The PIC32MX family sits at the entry of Microchip's MIPS-based 32-bit portfolio, providing substantially higher throughput than 8/16-bit PIC MCUs while retaining a familiar MPLAB toolchain. M4K is a 5-stage pipeline core originally licensed from MIPS Technologies, augmented by single-cycle MAC, atomic bit manipulation, and a single-wire debug port. PIC32MX5/6/7 devices further add hardware 10/100 Ethernet MAC and full-speed USB OTG, placing them in the embedded-connectivity tier above simple GPIO controllers. Key features include 128 KB Flash (128K × 8), 32 KB SRAM, 80 MHz core with 1.56 DMIPS/MHz throughput, USB 2.0 full-speed OTG with on-chip transceiver, 10/100 Ethernet MAC, two CAN 2.0B controllers, a 16-channel 10-bit 1 Msps ADC, and an integrated DMA controller with 8 channels. The device offers up to 85 general-purpose I/O pins, two I2C, two UART (one with IrDA/ISO7816), two SPI, and a 16-bit Parallel Master Port for off-chip memory expansion. The 100-pin TQFP package supports a wide temperature grade (-V: -40 °C to +105 °C) for industrial environments. Typical applications include industrial control panels with Ethernet/IP connectivity, USB human-interface devices (keyboards, mass storage, vendor-class peripherals), CAN-based automotive sub-modules (non-safety-critical), point-of-sale terminals, and embedded web servers. The combination of Ethernet + USB + CAN + ample RAM lets a single PIC32MX7 device replace what previously required multiple MCUs plus an external PHY. When designing with this part, pay attention to the 3.3 V supply rail noise: the integrated PLL can be sensitive to noisy rails. Decouple VDD with at least one 0.1 µF ceramic per supply pin pair plus bulk, and follow Microchip's recommended decoupling guide in the datasheet for full-speed USB applications.

USD $5,62 En stock

PIC32MX775F256H-80I/MR

PIC32MX775F256H-80I/MR - 80MHz 32-bit MCU, 256KB Flash, 64-VQFN | Microchip

The Microchip Technology PIC32MX775F256H-80I/MR is a 32-bit MIPS M4K microcontroller operating at up to 80 MHz with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 64-pin 9x9 mm VQFN (HVQCCN) package with industrial-grade temperature rating (-40C to +85C). What is a PIC32MX microcontroller? A PIC32MX is Microchip's family of MIPS-based 32-bit microcontrollers that combine the simplicity of the PIC16/24 ecosystem with the throughput required for connected embedded designs. It sits in the broader taxonomy of microcontroller > 32-bit MCU > MIPS core > connectivity MCU > semiconductor. The PIC32MX5/6/7 sub-family adds integrated 10/100 Mbit Ethernet MAC, USB 2.0 FS, and CAN peripherals that target connected industrial, consumer, and audio applications. Key differentiating features of the PIC32MX775F256H-80I/MR include: USB 2.0 Full-Speed On-The-Go (OTG) device/host controller, dual CAN 2.0b modules, 10/100 Ethernet MAC with RMII/MII interface, 16-bit parallel master port (PMP) for external graphics or memory, 8-channel DMA, and 16-bit timers/capture/compare/PWM modules. The 64-VQFN (9x9) footprint offers compact PCB integration while exposing 53+ general-purpose I/O pins. On the architecture side, the MIPS32 M4K core executes most instructions in a single cycle, delivering 1.56 DMIPS/MHz (Dhrystone 2.1) and up to 105 DMIPS at 80 MHz. The bus matrix is multi-layer AHB/APB, allowing simultaneous DMA and CPU transfers. The device supports MPLAB Harmony, MPLAB XC32, and Microchip's library ecosystem, plus a hardware trace port (PGEC2/PGED2) for real-time debug with MPLAB ICD 3 or PICkit 3. Typical applications include industrial control (Modbus TCP gateways, BACnet controllers), connected consumer products (audio streaming docks, smart appliances with Ethernet), automotive infotainment peripherals, point-of-sale terminals, and embedded web servers. The 2.5V/3.3V core with wide 2.3V-3.6V VDD tolerance simplifies mixed-signal designs. Design consideration: at 80 MHz the core current consumption is roughly 70 mA typical, so a clean 3.3V LDO (minimum 100 mA) with low-noise output is required. Decoupling: 100 nF + 4.7 uF bulk cap at each VDD/VSS pair is recommended by the manufacturer datasheet. This page synthesizes distributor pricing, same-family and cross-brand drop-in alternatives, and engineering design notes not found in the manufacturer datasheet.

USD $6,95 En stock

PIC32MX775F256H-80V/MR

PIC32MX775F256H-80V/MR - 80MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MX775F256H-80V/MR is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 256 KB of Flash and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates a 10/100 Mbit Ethernet MAC, two CAN 2.0 controllers, USB-OTG, six UART, five I2C, four SPI, a 16-bit Parallel Master Port, a 16-bit 10-channel ADC and a 10-bit DAC, giving the full PIC32MX5/6/7 connectivity peripheral set in one die. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable peripherals around a shared bus. The PIC32MX family extends Microchip’s legacy PIC architecture into 32-bit MIPS territory, providing deterministic interrupt latency, hardware multiply/divide, and a peripheral set aimed at embedded connectivity, HMI/graphics, and general-purpose control. Within that hierarchy the PIC32MX775F256H sits in the connectivity-rich tier alongside PIC32MX575/575/675 derivatives. The headline specifications include 256 KB Flash with self-programming, 64 KB RAM, 51 GPIO across five ports, and an extended industrial temperature range of -40C to +105C. The on-chip 80 MHz oscillator (with PLL) plus 8 MHz internal RC source give flexible clocking for low-power and high-throughput modes. The integrated 10/100 Ethernet MAC with RMII/MII interface and dedicated DMA channels enables low-BOM-cost networking without an external controller. Architecturally the device uses a 5-stage MIPS32 M4K pipeline with hardware multiply/divide and a tightly-coupled peripheral bus, allowing deterministic DMA-driven I/O. Power management supports run, idle, and sleep modes with switchable clock sources, making the part suitable for both line-powered and battery-operated industrial nodes. Hardware crypto/hash and unique 128-bit device serial number aid in secure boot and node identity. Typical applications include industrial Ethernet gateways, factory automation PLCs, networked sensors and HVAC controllers, USB-OTG device/host bridges, CAN-bused motor control nodes, and embedded HMI panels with graphics. The combination of 256 KB Flash, 64 KB RAM, and the integrated Ethernet+CAN+USB peripheral mix positions this part for industrial IoT edge devices. When designing with this device, allocate the Ethernet MAC pins to dedicated I/O, provide a 25 MHz external reference for the MAC PHY, and use Microchip’s MPLAB Harmony framework for TCP/IP and USB stacks. A 100 nF + 4.7 µF decoupling network is recommended near each power pin; follow the manufacturer pinout to prevent PCB rework. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet, providing an engineer-ready summary of the PIC32MX775F256H-80V/MR.

USD $2,84 En stock

PIC32MX775F256HT-80V/MR

PIC32MX775F256HT-80V/MR - 256KB Flash 80MHz MCU w/ USB-OTG & Ethernet | Microchip

The Microchip PIC32MX775F256HT-80V/MR is a 32-bit MIPS M4K microcontroller with 256KB Flash and 64KB SRAM, delivering 80 MHz (80 MIPS) performance while running from a 2.3 to 3.6V rail and integrating USB-OTG, two CAN controllers, 10/100 Ethernet MAC, and a rich analog/digital peripheral set inside a 64-pin 9x9 mm VQFN package. Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program storage (Flash), data memory (SRAM), and programmable peripherals. The PIC32MX family belongs to the 32-bit MCU category in the broader semiconductor hierarchy of microcontrollers -> embedded processors -> ICs. PIC32MX parts use the MIPS M4K core licensed from MIPS Technologies and are designed for embedded connectivity designs where high throughput and rich peripherals are required. Key features of the PIC32MX775F256HT-80V/MR include a MIPS32 M4K 32-bit CPU at 80 MHz (80 MIPS), 256KB Flash program memory, 64KB SRAM, integrated 10/100 Mbps Ethernet MAC for wired networking, USB 2.0 Full-Speed On-The-Go (OTG) controller, two independent CAN 2.0b modules for industrial/automotive fieldbus, 51 general-purpose I/O pins, multiple UART/SPI/I2C peripherals, 16-channel 10-bit ADC, five 16-bit timers, and a parallel master port for external bus/FPGAs. The wide 2.3-3.6V supply range simplifies designs running from a single Li-ion or 3.3V regulated rail. The architecture combines Harvard-style separate Flash/SRAM buses with DMA, prefetch cache, and a peripheral bus matrix, delivering deterministic interrupt latency at 80 MHz. The 9x9 mm 64-VQFN package exposes all peripherals while keeping the PCB footprint modest, and the -80V speed grade + -40C to +105C extended temperature rating supports industrial and consumer connectivity products. Typical applications include industrial Ethernet gateways, USB-OTG device/host controllers, CAN-based automotive/industrial node controllers, building automation panels, RFID readers, and graphical HMI displays with external bus peripherals. When designing with this MCU, allocate sufficient decoupling (100 nF + 10 uF bulk) close to each VDD pin pair and follow the 64-VQFN land recommendations in the datasheet to keep the lead-free thermal pad soldered for low theta-JA. This page synthesizes cross-distributor stock and pricing, drop-in PIC32MX alternatives, and practical design notes not consolidated in the manufacturer datasheet, giving an engineer an explicit BOM decision and PCB layout aid.

USD $5,46 En stock

PIC32MX775F256HT-80V/PT

PIC32MX775F256HT-80V/PT - 80MHz 32-bit MCU, 256KB Flash, USB, ETH, CAN | Microchip

The Microchip Technology PIC32MX775F256HT-80V/PT is a 32-bit MIPS M4K microcontroller from the PIC32MX5/6/7 family, integrating 256KB Flash, 64KB SRAM, 10/100 Mbps Ethernet MAC, USB-OTG, dual CAN, and 51 GPIOs in a 64-pin TQFP (10x10 mm) package operating at up to 80 MHz. It is the tape-and-reel, V-grade (-40C to +105C) variant of the PIC32MX775F256H silicon, optimized for industrial and harsh-environment designs requiring high-speed connectivity. A 32-bit microcontroller (MCU) is a programmable processor with a 32-bit data path, on-chip Flash program memory, SRAM, and a peripheral set. MCUs form the control tier of embedded systems: sensor acquisition, communication stack execution, and actuator control all run on the MCU. The PIC32MX775 series adds integrated 10/100 Ethernet MAC, USB-OTG, and CAN, eliminating the external PHY/MAC bridge in connected designs. Within Microchip's portfolio, the PIC32MX5/6/7 family targets cost-sensitive connected nodes; higher-integration needs (DSP, graphics, larger memory) move to PIC32MZ. Key features include 256KB Flash, 64KB SRAM, 80 MHz CPU with 1.56 DMIPS/MHz, 51 digital I/O, USB-OTG, dual CAN 2.0B, 10/100 Ethernet MAC (MII/RMII), 16-bit parallel master port, up to 6 UART, 4 SPI, 5 I2C, 16-bit timers and 5 PWM/OC channels, 16-channel 10-bit ADC at 1 Msps, and integrated DMA. The 2.3-3.6 V Vdd range simplifies 3.3 V system design. The architecture combines a MIPS M4K 32-bit core with Microchip peripherals. Dedicated DMA channels offload UART/SPI/I2C/ADC transfers, freeing the CPU for protocol or application tasks. The Ethernet MAC is industry-standard MII/RMII; pairing with a Microchip KSZ8041 PHY yields a complete 10/100 link without glue logic. Typical applications include industrial Ethernet gateways, CAN-bus bridges, USB-OTG device controllers, building-automation controllers, and embedded web-server modules. MPLAB Harmony framework and XC32 toolchain support firmware development. When designing with this part, allocate a 4-layer PCB for Ethernet signal integrity, place the 0.1 uF decoupling within 5 mm of each Vdd pin, and ensure the V-temp grade is matched to your enclosure thermal profile. This page synthesizes real distributor stock and pricing, drop-in V/I-grade alternatives, and design notes that complement the manufacturer datasheet for procurement and engineering decisions.

USD $7,65 En stock

PIC32MX775F256L-80I/BG

PIC32MX775F256L-80I/BG - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX775F256L-80I/BG is a 32-bit MIPS32 M4K microcontroller operating at 80 MHz with 256 KB Flash and 64 KB RAM, integrated 10/100 Ethernet MAC, USB-OTG, dual CAN, and 8-channel DMA. It is housed in a 121-pin TFBGA package (10x10 mm) with 83 GPIO lines and is specified for the industrial temperature range. A 32-bit microcontroller is an integrated circuit that combines a high-performance processor core, volatile memory (SRAM), non-volatile program memory (Flash), and a rich set of peripherals on a single die. The PIC32MX family from Microchip implements the MIPS32 M4K architecture, which supports the MIPS instruction set and offers deterministic interrupt handling. Within the broader embedded taxonomy, the PIC32MX sits between 8/16-bit MCUs (PIC16, PIC24) and higher-end Cortex-M parts, delivering MHz-class processing with deterministic peripheral behavior and a 32-bit data path. This product type belongs to the hierarchy: microcontroller -> embedded processor -> semiconductor IC -> electronic component. Key features include a maximum clock speed of 80 MHz, 256 KB of Flash program memory, 64 KB of SRAM, integrated 10/100 Mbps Ethernet MAC, USB-OTG full-speed PHY, two CAN 2.0b modules, eight DMA channels, and a 10-bit ADC. The 83 I/O pins support 5V-tolerant inputs, and the part operates from 2.3 V to 3.6 V, simplifying designs powered from a single Li-ion cell or 3.3 V regulated rail. The PIC32MX775F256L uses the MIPS32 M4K core with 5-stage pipeline, hardware multiply/divide, and a single-cycle shadow register set for fast interrupt response. The dual CAN, USB-OTG, and Ethernet MAC make it suitable for connected-embedded applications where the MCU must manage multiple wired protocols concurrently without an external PHY bridge. DMA offloads memory-to-peripheral and peripheral-to-memory transfers, freeing the core for application code. Typical applications include industrial Ethernet gateways, CAN-bridge automotive ECUs, USB Human Interface Devices, embedded web servers, and factory automation controllers. The combination of Ethernet + USB + dual CAN in a single 32-bit MCU reduces BOM and PCB area for connectivity-rich designs. When designing with this part, pay attention to the BGA package - it requires a 4-layer PCB with laser-via fanout for reliable assembly. The MPLAB Harmony framework and XC32 compiler are the canonical toolchain. Decoupling must include 100 nF on every VDD/VSS pair and a bulk 4.7 uF tantalum near the analog supply. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing an engineer-ready reference for sourcing PIC32MX775F256L-80I/BG.

USD $6,42 En stock

PIC32MX775F256L-80I/PF

PIC32MX775F256L-80I/PF - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX775F256L-80I/PF is a 32-bit MIPS M4K microcontroller operating at 80 MHz (105 DMIPS) with 256 KB Flash and 64 KB SRAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates 10/100 Ethernet MAC, USB 2.0 On-The-Go with integrated PHY, two CAN 2.0b controllers, 8 DMA channels, and 83 general-purpose I/O lines, making it one of the most feature-rich members of the PIC32MX5/6/7 family. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and GPIO into a single chip. The PIC32MX architecture belongs to the broader category of 32-bit embedded microcontrollers (hypernym: MCU -> microcontroller -> embedded processor -> semiconductor) and is designed for connected, real-time, and graphically-rich embedded systems where both deterministic control and high-bandwidth connectivity are required. Key differentiating specifications of this part include 256 KB of self-programmable Flash, 64 KB SRAM, 16-bit parallel master port (PMP) for graphics or external memory, a 10-bit 1 Msps ADC with up to 16 channels, five 16-bit timers/counters, and operation across 2.3V to 3.6V with industrial-grade -40C to +85C temperature range. The 'L' (large pin count) variant offers the maximum 100-pin I/O complement for the family. Architecturally, the PIC32MX775 executes instructions through a 5-stage pipeline with Harvard bus architecture, supporting single-cycle multiplication and hardware divide for high computational throughput. Integrated DMA offloads USB, Ethernet, and CAN transfers from the CPU, freeing cycles for application logic. The USB 2.0 OTG controller embeds the physical transceiver, eliminating external PHY cost and board area. Typical applications include industrial Ethernet gateways, building automation controllers, USB peripherals and HID devices, automotive infotainment and telematics interfaces, CAN-based industrial sensor hubs, and point-of-sale terminals. The combination of Ethernet + USB OTG + dual CAN positions the part uniquely for bridged industrial networks. When designing in this part, ensure the 2.5V/3.3V core supply decoupling is robust - use at least 0.1uF and 10uF ceramic capacitors close to every VDD/AVDD pin. Because the device is supplied in 100-pin TQFP, hand-rework is straightforward, but high-density multilayer routing is recommended to keep analog and digital grounds properly partitioned. This page synthesizes distributor pricing, drop-in Microchip and cross-brand alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $7,94 En stock

PIC32MX775F256L-80V/BG

PIC32MX775F256L-80V/BG - 32-bit MCU 80MHz 256KB Flash | Microchip

The Microchip PIC32MX775F256L-80V/BG is a 32-bit MIPS M4K microcontroller running at up to 80 MHz (105 DMIPS), integrating 256 KB Flash and 64 KB SRAM with USB-OTG, dual CAN 2.0b, and a 10/100 Ethernet MAC in a 121-ball TFBGA (10x10 mm) package. It operates from 2.3V to 3.6V and is qualified for the -40C to +105C industrial temperature range, supported by the MPLAB Harmony ecosystem. Background: a 32-bit microcontroller (MCU) is a programmable processor-on-a-chip that integrates CPU core, Flash program memory, SRAM, and peripherals (timers, ADC, communication blocks). The PIC32MX family implements the MIPS32 M4K core, a Harvard-architecture RISC with 5-stage pipeline optimized for deterministic interrupt response. Within Microchip's portfolio, PIC32 sits between PIC16/PIC24 (lower pin counts, simpler peripherals) and the Cortex-M class (often faster cores, similar peripheral richness). It is best understood as: MCU -> 32-bit MCU -> MIPS MCU -> PIC32MX family -> connectivity class (Ethernet + USB-OTG + CAN). Key features: 8-channel DMA, 16-bit parallel master port, 5 16-bit timers/capture/compare, two I2C, two SPI, four UART, USB-OTF 2.0 peripheral with integrated PHY, dual CAN 2.0b modules with 1024 message buffers, and a 10/100 Ethernet MAC with MII/RMII interfaces. The IC ships in 121-ball TFBGA (10x10 mm) and provides up to 83 I/O pins for mixed-signal or connectivity-heavy designs. Technical depth: the M4K pipeline plus 8 dedicated DMA channels offload USB-OTG, Ethernet, and CAN traffic from the CPU, enabling deterministic throughput on the simultaneous-communication scenarios this part is designed for. The 16-bit PMP plus DMA simplifies connection to graphic controllers, external bus memories, or FPGA co-processors. Typical applications: industrial Ethernet gateways, CAN/J1939 nodes, USB-OTG device/host controllers, embedded web servers, and motor-control HMIs. Design tip: ensure the BGA substrate via-in-pad microvia stack matches the 0.65 mm ball pitch; JTAG/Trace must be brought out for MPLAB ICD 3 / REAL ICE in-circuit debug.

USD $6,55 En stock

PIC32MX775F256L-80V/PF

PIC32MX775F256L-80V/PF - 80MHz 32-bit MCU w/ 256KB Flash | Microchip

The Microchip Technology PIC32MX775F256L-80V/PF is a 32-bit MIPS32 M4K microcontroller running at up to 80 MHz with 256 KB of Flash program memory and 64 KB of SRAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates a 10/100 Mbit Ethernet MAC, USB-OTG, two CAN modules, and a 10-bit ADC, making it a connectivity-rich MCU for embedded networking applications. A 32-bit microcontroller (MCU) is a single-chip computer built around a 32-bit data path and instruction set, offering higher throughput, larger addressable memory, and richer peripherals than 8-bit or 16-bit MCUs. The PIC32MX family sits in the hierarchy: 32-bit MCU -> MIPS-based MCU -> PIC32 family -> PIC32MX5/6/7 sub-family, which Microchip positions as the entry-level 32-bit platform with on-chip connectivity peripherals. Key features of the PIC32MX775F256L-80V/PF include: 256 KB Flash organized as 256K x 8, 64 KB SRAM, a 10-bit ADC with up to 16 channels and 1 Msps conversion rate, 5 general-purpose 16-bit timers/counters, an RTCC, and a DMA controller with 4 channels. The device operates from 2.3V to 3.6V and supports an industrial temperature range of -40C to +105C, making it suitable for harsh environments. Communication peripherals include USB-OTG, two CAN 2.0B controllers, 10/100 Ethernet MAC with MII/RMII interface, four UARTs, three SPI ports, and two I2C ports. Architecturally, the PIC32MX uses the MIPS32 M4K core, a 5-stage pipeline RISC architecture with single-cycle multiply and hardware divide. The 80 MHz clock delivers 1.56 DMIPS/MHz (Dhrystone 2.1) of integer performance. The integrated DMA controller offloads data movement between peripherals and memory, freeing the CPU for application logic. Code is fully supported by MPLAB X IDE, MPLAB Harmony v3 framework, and the XC32 compiler. Typical applications include industrial Ethernet nodes (Modbus TCP, EtherNet/IP gateways), CAN-based automotive body and powertrain networks, USB-OTG device/host peripherals, building automation controllers, and embedded web servers. The wide peripheral integration makes the device particularly suited for connected sensor hubs and IoT edge nodes requiring multiple wired interfaces. A key design consideration is that this MCU does not include an integrated PHY - Ethernet applications require an external PHY such as the LAN8720A or DP83848. Decoupling: place 0.1 uF ceramic capacitors on each VDD pin and a bulk 10 uF tantalum or ceramic near the voltage regulator; the device is sensitive to supply noise during ADC conversions. This page synthesizes verified distributor pricing, drop-in alternative MPNs in the same 100-pin TQFP footprint, and practical design notes not collected in any single datasheet page, helping procurement and firmware engineers shorten BOM selection cycles.

USD $5,55 En stock

PIC32MX775F256L-80V/PT

PIC32MX775F256L-80V/PT - 80MHz 256KB Flash MCU w/ USB-OTG | Microchip

The Microchip PIC32MX775F256L-80V/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz (105 DMIPS) with 256 KB Flash and 64 KB SRAM, housed in a 100-pin TQFP (12x12 mm) package. It integrates USB 2.0 On-The-Go (OTG) with integrated PHY, two independent CAN 2.0b modules, and a 10/100 Ethernet MAC with MII/RMII interfaces, enabling connected-embedded designs on a single die. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, peripherals, and I/O on a single silicon die. The PIC32MX7 family is a high-performance MIPS32 M4K-based MCU line from Microchip's PIC32 portfolio, positioned between the PIC32MX5 (no USB-OTG) and PIC32MX6 sub-families. Within the broader taxonomy it belongs to: 32-bit MCU -> MIPS32 MCU -> PIC32 family -> PIC32MX7xx sub-family -> PIC32MX775F256L. This hierarchy helps engineers locate compatible parts within Microchip's PIC32 catalog. Key features include 8 dedicated DMA channels for USB-OTG, Ethernet, and CAN peripherals, a 5-stage Harvard pipeline, and 83 programmable I/O lines. Peripherals include a 10-bit 1 Msps ADC (16 channels), five 16-bit timers/counters, five input-capture and five output-compare modules, and a Parallel Master Port for off-chip memory expansion. An industrial-grade -40C to +105C operating range is supported via the -80V speed grade. Technical depth: the M4K core executes one instruction per cycle with single-cycle hardware multiply, reaching 105 DMIPS at 80 MHz. The on-chip 256 KB Flash is single-cycle accessible from the prefetch buffer, while 64 KB SRAM supports unified program/data access. The integrated 10/100 MAC offloads TCP/IP processing, leaving the CPU free for application logic. Dedicated DMA channels remove CPU intervention from USB, Ethernet, and CAN transfers, reducing interrupt load in networked real-time systems. Typical applications include industrial Ethernet gateways, USB-OTG device/host controllers, automotive CAN nodes (non-safety), connected HMI panels with parallel LCD, and multi-protocol embedded routers. The dual-CAN capability also supports CANopen and DeviceNet bridges. Design consideration: route the 80 MHz traces as impedance-controlled length-matched pairs, and place the 12 MHz crystal within 10 mm of the OSCI/OSCO pins to meet USB-OTG jitter spec. This page synthesizes verified distributor pricing, true drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

USD $2,75 En stock

PIC32MX775F256LT-80I/BG

PIC32MX775F256LT-80I/BG - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX775F256LT-80I/BG is a 32-bit MIPS M4K microcontroller operating from a 2.3V to 3.6V supply with 256KB of Flash and 64KB of SRAM in a 121-pin TFBGA (10x10 mm) package. It integrates a 10/100 Mbit Ethernet MAC, USB 2.0 Full-Speed OTG, two CAN 2.0b controllers, eight DMA channels and a rich mix of analog and digital peripherals for industrial connectivity applications. The 80 MHz core delivers up to 1.56 DMIPS/MHz and 3.28 CoreMark/MHz of compute performance for embedded control tasks. A 32-bit microcontroller (MCU) is a programmable processor with on-chip Flash program storage, SRAM data memory, and integrated peripherals such as timers, ADC, communication controllers and DMA. Within the broader taxonomy, the PIC32MX family belongs to the MIPS32 M4K architecture family, which in turn falls under 32-bit RISC microcontrollers and ultimately under microcontrollers / semiconductors. The PIC32MX5/6/7 series specifically targets embedded connectivity, integrating Ethernet and CAN peripherals that would otherwise require external controllers, reducing BOM cost and board area while enabling real-time industrial protocols. Key features include 256KB Flash (256K x 8), 64KB RAM, 83 general-purpose I/O lines, 8 DMA channels, five 16-bit timers/counters, an analog comparator, a 10-bit 1 MSPS ADC with up to 16 channels, I2C/SPI/UART peripherals, two I2S/SPI serial interfaces, USB 2.0 Full-Speed OTG, two CAN 2.0b modules, 10/100 Ethernet MAC with MII/RMII interfaces, and an RTCC. The 121-ball TFBGA package provides a compact 10x10 mm footprint at 0.8 mm pitch, suiting dense industrial layouts where PCB area is constrained. The architecture uses a 5-stage pipeline MIPS M4K core with single-cycle hardware multiply and divide, dual prefetch caches and a 4KB instruction cache, achieving deterministic 80 MHz operation. Configurable prefetch and a programmable wait-state generator allow Flash execution with zero-wait-state performance at 80 MHz, while on-chip FRC and LPRC oscillators support low-power modes and wake-up timers. Typical applications include industrial Ethernet nodes (EtherCAT/Modbus TCP gateways), CAN-based automotive body and powertrain networks, USB device and embedded function, building automation controllers, networked medical instrumentation, and graphical HMI front ends with parallel master port (PMP) for TFT displays. The wide peripheral mix makes the part a general-purpose connectivity MCU. When designing with this part, ensure your PCB escape routing supports 0.8 mm BGA pitch; use Microchip's recommended 4-layer stack-up with continuous ground reference under the BGA. Plan for proper decoupling (0.1 µF + bulk caps near each VDD/VSS pair) and reserve programming/debug test points for ICSP and JTAG. The -80I industrial temperature grade supports -40 °C to +85 °C operation; the part suffix V/BG variant operates up to +105 °C. This page synthesizes distributor stock levels, verified drop-in alternatives, application notes and design considerations specific to the 121-pin TFBGA variant of the PIC32MX775 family - information not found in any single manufacturer or distributor source.

USD $7,65 En stock

PIC32MX775F256LT-80V/BG

PIC32MX775F256LT-80V/BG - 80MHz 32-bit MCU with ETH/USB/CAN | Microchip

The Microchip Technology PIC32MX775F256LT-80V/BG is a 32-bit MIPS32 M4K microcontroller operating at up to 80 MHz, integrating 256 KB of Flash program memory and 64 KB of SRAM in a 121-pin TFBGA (10x10 mm) surface-mount package. It features 10/100 Mbit Ethernet MAC, USB-OTG, two CAN modules, and up to 105 DMIPS of processing performance for connected-embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. The PIC32MX family belongs to the broader 32-bit MCU taxonomy: 32-bit microcontroller -> MIPS32 M4K core -> Microchip PIC32 -> Microchip Connectivity Line, sitting under the wider category of microcontrollers (semiconductor -> IC -> microcontroller). The '5/6/7' series specifically targets connected-embedded applications with on-chip Ethernet, USB, and CAN. Key features of the PIC32MX775F256LT-80V/BG include: 256 KB Flash (256K x 8) for code storage, 64 KB SRAM for runtime data, 80 MHz maximum operating frequency delivering 105 DMIPS, integrated 10/100 Ethernet MAC with MII/RMII interface, USB 2.0 Full-Speed OTG controller, two independent CAN 2.0B modules, sixteen 10-bit ADC inputs, five 16-bit timers/counters, and a wide operating voltage of 2.3 V to 3.6 V. The 'T' suffix indicates tape-and-reel packaging, 'V' denotes the -40C to +105C industrial-grade temperature range, and 'BG' identifies the 121-pin TFBGA package. Architecturally, the device uses a 5-stage pipelined MIPS32 M4K core with hardware multiply/divide, separate program Flash bus and SRAM bus (Harvard architecture), and a peripheral bus that supports DMA for high-throughput Ethernet and USB transfers. Code execution is in-place from Flash via an instruction cache, allowing zero-wait-state performance at 80 MHz. Typical applications include industrial Ethernet gateways, USB-OTG device controllers, CAN-based automotive body controllers, point-of-sale terminals, and connected medical devices. The integrated triple-connectivity (Ethernet + USB + CAN) makes the part especially well suited for protocol-bridging nodes that must translate between factory, automotive, and IT networks. When designing with this part, pay attention to the 121-ball TFBGA layout (0.8 mm pitch): it requires via-in-pad PCB fabrication and 4-layer routing for clean Ethernet signal integrity. Also confirm the 'V' temperature grade matches your end-environment, and use MPLAB Harmony or MPLAB XC32 for firmware development with the integrated peripheral libraries. This page synthesizes distributor pricing across DigiKey/Mouser/Octopart, Microchip-recommended drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, providing engineering decision support beyond the basic parametric page.

USD $7,48 En stock

PIC32MX775F256LT-80V/PF

PIC32MX775F256LT-80V/PF - 80MHz 32-bit MCU, 256KB Flash, USB-OTG, 100-TQFP

The Microchip Technology PIC32MX775F256LT-80V/PF is a 32-bit MIPS MCU from the PIC32MX5/6/7 family, featuring a MIPS32 M4K core running up to 80 MHz, with 256 KB Flash and 64 KB RAM, integrated USB-OTG, dual CAN, 10/100 Ethernet MAC, 16-channel 10-bit ADC, and DMA, housed in a 100-pin TQFP package. The part suffix "/PF" denotes the 100-pin TQFP (14x14 mm) lead-free package, while "LT" indicates tape-and-reel packing and "80V" denotes the 80 MHz speed grade with the -40C to +105C extended industrial temperature range. Operating voltage spans 2.3 V to 3.6 V across 51 GPIO pins, giving designers flexible I/O assignment for embedded connectivity designs. A PIC32MX microcontroller is a 32-bit MIPS-based MCU that bridges 8/16-bit PIC legacy code with modern connected-embedded workloads. Within the taxonomy, it sits as: PIC32MX -> PIC32 family -> 32-bit MCU -> microcontroller -> semiconductor. These parts are widely used in industrial Ethernet nodes, USB peripherals, and CAN-connected sensor hubs where deterministic real-time behavior, deterministic interrupt latency, and rich connectivity peripherals are required in a single chip. Key features include 256 KB single-cycle Flash with prefetch, 64 KB SRAM with DMA, hardware crypto engine (the F775 suffix implies AES/Random Number Generator availability on certain family members - confirm per datasheet revision), parallel master port, and five 16-bit timers. The 80 MHz core delivers 1.56 DMIPS/MHz (Dhrystone 2.1) and executes most instructions in one clock cycle, while the 10-bit ADC supports 1 Msps conversion with up to 16 analog inputs. The PIC32MX775F256L architecture pairs an MIPS M4K pipeline with peripheral pin select via PPS, USB-OTG full-speed and high-speed (when paired with external PHY on related parts), and 10/100 Mbps Ethernet MAC. The device supports MPLAB Harmony, MPLAB X IDE, XC32 compiler, and Microchip's TCP/IP, USB, and graphics stacks. The F775 variant specifically integrates an Ethernet MAC plus dual CAN controllers plus USB-OTG, distinguishing it from lower-pinout PIC32MX3xx/4xx parts. Typical applications include industrial Ethernet gateways, building automation controllers, USB-to-UART bridges with CAN diagnostics, point-of-sale terminals, medical patient monitors, and motor-control inverters with CANopen. The wide 2.3-3.6 V supply and extended industrial temperature make it attractive for factory-floor equipment. Design consideration: place 0.1 uF decoupling capacitors on every VDD/VSS pair within 3 mm of the pins, route the 80 MHz crystal traces symmetrically with ground guard rings, and use MPLAB Harmony's free TCP/IP stack to shorten firmware time-to-market. For high-EMI environments, enable the on-chip FPLL jitter filter and gate unused peripherals via the peripheral clock control registers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $6,74 En stock

PIC32MX775F512H-80I/MR

PIC32MX775F512H-80I/MR - 80MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC32MX775F512H-80I/MR is a 32-bit MIPS32 M4K microcontroller IC operating at 80 MHz with 512 KB of Flash and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates a 10/100 Ethernet MAC, USB 2.0 On-The-Go with integrated PHY, two CAN 2.0b modules, 8 dedicated DMA channels, and 51 general-purpose I/O pins in an industrial -40C to +85C temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one device. Within the embedded system hierarchy, the PIC32MX775F512H sits in the high-performance 32-bit MCU class, above 8/16-bit MCUs and below MPU-based application processors. It targets connected-embedded designs where Ethernet, USB, and CAN are required simultaneously. Key features include 105 DMIPS performance from the MIPS32 M4K core with single-cycle hardware multiply, 16-bit (MX789) or 32-bit instructions, hardware trace and JTAG debug support, and a 5-stage pipeline. The Ethernet MAC supports both MII and RMII interfaces, the USB 2.0 OTG peripheral includes a transceiver and pull-up/pull-down resistors, and the two CAN modules include 1024-message buffers each. Typical applications include industrial Ethernet gateways, USB device/host controllers, CAN-based automotive networks, building automation controllers, and embedded web servers. The wide peripheral set reduces external component count, while the 80 MHz MIPS32 core leaves headroom for TCP/IP stacks such as Microchip's MPLAB Harmony. When designing with this MCU, ensure your PCB layout follows the VQFN-9x9 thermal pad soldering guidelines (a continuous ground plane under the exposed pad is mandatory) and place the 8 MHz crystal within 1 cm of the OSC1/OSC2 pins. The USB PHY requires a 48 MHz clock derived from the PLL; consult Microchip application note AN1429 (USB on PIC32) for hub/host listings.

USD $5,41 En stock

PIC32MX775F512H-80I/PT

PIC32MX775F512H-80I/PT - 80MHz 512KB Flash 32-bit MCU | Microchip

The Microchip Technology PIC32MX775F512H-80I/PT is a 32-bit MIPS32 M4K microcontroller running at up to 80 MHz (105 DMIPS), integrating 512 KB Flash and 128 KB SRAM in a 64-pin TQFP (10x10 mm) package. It combines USB 2.0 On-The-Go, 10/100 Ethernet MAC with MII/RMII, two CAN 2.0b controllers, eight DMA channels and 51 general-purpose I/Os, targeting connected embedded applications. A 32-bit microcontroller (MCU) is a single-chip processor with on-chip Flash, SRAM and peripherals that executes instructions on 32-bit data paths. PIC32 devices extend Microchip's PIC architecture into the MIPS32 M4K core, sitting at the high-performance end of the PIC family above 8-bit PIC16/PIC18 and 16-bit PIC24/dsPIC. They run C/C++ firmware with industry-standard toolchains and are supported by MPLAB X IDE and MPLAB Harmony framework. Key features include a 5-stage pipeline core delivering 105 DMIPS at 80 MHz, hardware multiplier/divider for DSP-class math, USB 2.0 OTG with integrated PHY, parallel master port (PMP) for external bus/graphics, two I2C, two SPI, six UART, two CAN 2.0b modules, 16-bit timers/capture/compare/PWM and a 16-channel 10-bit ADC at 1 Msps. Operating voltage is 2.3 V to 3.6 V, junction temperature -40 °C to +105 °C (industrial). Typical applications are industrial Ethernet nodes, CAN-bridge gateways, USB-OTG devices, multi-protocol sensor hubs, point-of-sale terminals, HVAC controllers and graphics HMI with PMP. Engineered for deterministic real-time performance, the integrated DMA offloads USB, Ethernet and CAN from the core, leaving headroom for the application stack. Design tip: route Ethernet differential pairs (TPIN+/-, TPOUT+/-) with 100 Ω controlled impedance and place the 50 MHz RMII crystal within 10 mm of the OSCI/OSCO pins to meet IEEE 802.3 timing. This page synthesizes XAIPART distributor pricing, drop-in Microchip family alternatives, and practical Ethernet/USB layout notes beyond the manufacturer datasheet.

USD $6,20 En stock

PIC32MX775F512H-80V/PT

PIC32MX775F512H-80V/PT - 80MHz 512KB Flash MCU w/ ETH+USB-OTG+CAN | Microchip

The Microchip PIC32MX775F512H-80V/PT is a 32-bit MIPS M4K microcontroller operating at 80 MHz (105 DMIPS), integrating 512 KB Flash, 64 KB RAM, USB 2.0 On-The-Go with integrated PHY, 10/100 Ethernet MAC, two CAN 2.0b controllers, and 51 to 53 general-purpose I/O in a 64-pin TQFP (10x10 mm) package. The -80V speed grade and industrial temperature range (-40C to +105C) make it suitable for harsh-environment embedded designs. A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU, memory, and programmable peripherals around a 32-bit data path. Microcontrollers sit within the broader taxonomy of microprocessors -> RISC processors -> embedded microcontrollers -> 32-bit MCUs, and within Microchip's PIC32MX family they are the MIPS-based high-performance tier above PIC24/dsPIC. The PIC32MX5/6/7 series specifically adds integrated connectivity peripherals (Ethernet MAC, USB-OTG, CAN) that historically required external components, simplifying BOM and reducing PCB area. This product belongs to the integrated circuits and microcontrollers module family hierarchy. Key features include a 5-stage pipeline MIPS32 M4K core with hardware multiply/divide and single-cycle MAC, eight dedicated DMA channels that offload the CPU for USB-OTG, Ethernet, and CAN transfers, dual CAN 2.0b modules with 1024 message buffers, parallel master port (PMP) for graphics or external memory, and a 16-channel 10-bit ADC at 1 Msps. The work group also provides five 16-bit timer/counters, two UARTs, two SPI ports, and two I2C ports. The architectural combination of dedicated DMA, separate peripheral buses, and on-chip PHY allows deterministic real-time performance for industrial networking stacks such as Modbus TCP/IP, EtherNet/IP, and CANopen, while leaving CPU bandwidth for the application layer. Fail-Safe Clock Monitor and multiple power management modes support robust field deployments. Typical applications include industrial Ethernet gateways, USB-OTG device/host peripherals, CAN-based motor control nodes, embedded web servers, and graphical HMI panels using PMP to drive TFT LCDs. When designing with this device, ensure the 2.3 V to 3.6 V supply is well decoupled near each VDD/VSS pair; use the on-chip LDO for the 1.8 V internal core, and follow the package land pattern with continuous thermal vias under the exposed pad. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers shortlist the PIC32MX775F512H against modern alternatives.

USD $8,59 En stock

PIC32MX775F512HT-80I/MR

PIC32MX775F512HT-80I/MR - 80MHz 512KB MCU USB/CAN/Ethernet | Microchip

The Microchip Technology PIC32MX775F512HT-80I/MR is a 32-bit MIPS32 M4K PIC microcontroller delivering 80 MHz CPU performance, 512 KB of Flash program memory and 64 KB of SRAM, housed in a 64-pin VQFN (9x9 mm) industrial-grade (-40C to +85C) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and a rich set of peripherals into one package. Within the broader taxonomy, the PIC32MX775 sits under 32-bit MCU -> RISC MCU -> microcontroller -> integrated circuit -> semiconductor. Compared with 8-bit and 16-bit MCUs, a 32-bit MCU executes instructions on 32-bit data paths, allowing larger address spaces, higher throughput, and richer peripheral integration for connected embedded applications. Key features of the PIC32MX775F512HT-80I/MR include 80 MHz core speed, 512 KB Flash, 64 KB SRAM, integrated USB 2.0 Full-Speed device/host/OTG, two CAN 2.0b controllers, a 10/100 Mbit Ethernet MAC, 8-channel DMA, and 5 timers / 5 IC/OC / 5 I2C / 4 UART / 2 SPI peripherals. The 64-VQFN (9x9 mm) package exposes 53 digital I/O pins and supports industrial operating temperatures from -40C to +85C. The device uses the MIPS32 M4K core with 5-stage pipeline and prefetch cache, executing most instructions in a single clock cycle. The dual Flash panel and live update partition allow firmware field updates via bootloader, while 8 DMA channels offload data movement between peripherals and RAM. USB, CAN, and Ethernet MACs share DMA, reducing CPU interrupt load in connected designs. Typical applications include industrial Ethernet nodes, CAN-connected motor and building automation controllers, USB peripherals and embedded hosts, factory automation gateways, and connected medical or instrumentation devices. The PIC32MX5/6/7 series is fully supported by MPLAB Harmony and MPLAB X IDE for firmware development. When designing, ensure the USB D+/D- trace impedance is 90 ohms differential and add a 1 uF bulk capacitor near the VBUS pin. Use the internal pull-up on D+ only in bus-powered designs; for self-powered devices, drive D+ through an external switchable resistor to avoid back-powering the host port. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $7,88 En stock

PIC32MX775F512HT-80V/MR

PIC32MX775F512HT-80V/MR - 80MHz 512KB Flash MCU | Microchip

The Microchip PIC32MX775F512HT-80V/MR is a 32-bit MIPS32 M4K microcontroller operating at up to 80 MHz, integrating 512 KB Flash, 64 KB RAM, USB-OTG, dual CAN, and 10/100 Ethernet MAC in a 64-pin VQFN (MR) 9x9 mm package. A 32-bit microcontroller (MCU) is a programmable processor core built on a wider data path than legacy 8/16-bit parts, allowing a single instruction to operate on 32-bit words. Within the broader taxonomy, this device sits as: microcontroller -> embedded MCU -> 32-bit MCU -> MIPS-based MCU -> PIC32 family. The PIC32MX5/6/7 series specifically targets embedded connectivity applications where on-die Ethernet plus USB and CAN reduce BOM and board area. Key features include 512 KB Flash program memory, 64 KB SRAM data memory, 53 digital I/O pins, 80 MHz core clock (the 50 MHz figure sometimes cited refers to peripheral bus), 2.3 V to 3.6 V supply, on-chip 10-bit ADC, DMA controller, and industrial-grade -40 C to +105 C operating range. The T-suffix denotes tape-and-reel delivery for high-volume assembly. Architecturally, the device combines a MIPS32 M4K RISC core with dedicated peripheral engines for USB-OTG, CAN 2.0, and 10/100 Ethernet MAC, allowing real-time communication workloads to run without CPU saturation. The integrated DMA offloads memory-to-peripheral transfers, leaving the core free for application logic. Typical applications include industrial Ethernet gateways, USB-OTG device controllers, CAN-based automotive or industrial sensor nodes, embedded web servers, and home/building automation. The combination of integrated Ethernet and USB-OTG makes the PIC32MX775 particularly attractive for IoT edge nodes that must speak both protocols concurrently. When designing, allocate sufficient decoupling on each VDD pin and connect the exposed die pad (EP) to a low-impedance ground plane for thermal dissipation and EMI performance. Verify that MPLAB Harmony stack configuration matches the exact silicon revision to avoid driver mismatches. This page synthesizes distributor pricing, drop-in alternative MPNs, and design notes not found in the standalone datasheet, giving procurement and engineering teams a one-stop reference.

USD $4,40 En stock

PIC32MX775F512HT-80V/PT

PIC32MX775F512HT-80V/PT - 80MHz 512KB Flash MCU w/ USB-OTG | Microchip

The Microchip Technology PIC32MX775F512HT-80V/PT is a 32-bit MIPS32 M4K microcontroller running at 80MHz with 512KB Flash and 64KB SRAM in a 64-pin TQFP (10x10 mm) package. It integrates USB-OTG, dual CAN, 10/100 Ethernet MAC, a 10-bit ADC, and a DMA controller in a single chip designed for embedded connectivity applications. A 32-bit MCU (microcontroller unit) is an integrated circuit containing a processor core, program memory (Flash), data memory (SRAM), and a rich mix of peripherals (USB, CAN, Ethernet, ADC, timers, GPIO). Compared with 8- or 16-bit MCUs, 32-bit parts execute instructions on wider registers, allowing faster arithmetic and more deterministic handling of communication stacks. The PIC32MX5/6/7 family specifically targets connected applications by integrating high-bandwidth peripherals (USB-OTG, Ethernet, dual CAN) that previously required an external MCU plus dedicated controller ICs. Key features include 512KB Flash organized as 512K x 8, 64KB SRAM, 51 usable I/O pins, four-wire SPI, I2C, dual CAN 2.0b, USB-OTG, 10/100 Mbps Ethernet MAC, 16-channel 10-bit ADC at 1 Msps, a 16-bit parallel master port, and a 4-channel DMA. The part operates from 2.3V to 3.6V, supports industrial temperature range (-40C to +105C), and is pin-compatible with most PIC24/dsPIC DSC devices in the same package footprint. The MIPS32 M4K core provides single-cycle multiplication, hardware divide, and a five-stage pipeline, delivering 1.56 DMIPS/MHz. Multiple power management modes (idle, sleep, deep sleep) and the Fail-Safe Clock Monitor reduce dynamic and standby power. Interrupt latency is deterministic and individually programmable in priority, which simplifies real-time fieldbus handling. Typical applications include industrial Ethernet gateways, CAN-based automotive body controllers, USB-OTG medical peripherals, building-automation controllers, and connected sensors in IoT edge nodes. The combination of Ethernet MAC, dual CAN, and USB-OTG in a single MCU removes the need for external interface bridges and shortens BOM cost. When designing with this part, plan the clock tree carefully - the 80MHz SYSCLK requires an 8MHz primary oscillator with on-chip PLL. Decouple VDDCORE pins with 1uF and 0.1uF ceramics close to the package and keep the analog AVdd rail separate to preserve ADC SNR. This page synthesizes distributor stock and pricing, lists pin-compatible drop-in alternatives from the same PIC32MX7 family, and provides practical design notes you will not see in the manufacturer datasheet.

USD $8,10 En stock

PIC32MX775F512L-80I/BG

PIC32MX775F512L-80I/BG - 80MHz 32-bit MCU 512KB Flash | Microchip

The Microchip PIC32MX775F512L-80I/BG is a 32-bit MIPS M4K microcontroller with 512KB Flash and 64KB RAM running at 80MHz, housed in a 121-pin TFBGA package (10x10mm). It integrates 10/100 Ethernet MAC, USB OTG, dual CAN, six UART, five I2C and four SPI peripherals, targeting embedded connectivity applications. A 32-bit microcontroller (MCU) is a programmable processor with integrated Flash program memory, RAM, peripherals and a CPU core, used as the central controller in embedded systems. PIC32 sits in the hierarchy: microcontroller -> embedded processor -> semiconductor. The MX775 sub-family specifically addresses connectivity by combining an Ethernet MAC, USB OTG and CAN on-chip, replacing external PHY-bridge chips in many designs and reducing BOM cost. Key features include 51 I/O ports, 8-channel DMA, 16-bit timers, a 10-bit ADC up to 1 Msps, an RTCC, and JTAG/ICSP debug. The 121-TFBGA package exposes the full peripheral set and gives 51 usable GPIO, but the 0.8mm ball pitch demands PCB fabrication with 4/4 mil trace/spacing and microvia stackups for fan-out, a constraint the Notice and trade-off guidance covers in the design notes. The PIC32MX775F512L-80I/BG also provides five I2C buses, four SPI buses, six UART modules, two CAN controllers and a full-speed USB OTG with on-chip transceiver. Code execution is 1.56 DMIPS/MHz, so 80 MHz delivers about 125 DMIPS, more than enough for protocol stacks such as TCP/IP, USB CDC and CANopen while leaving headroom for an RTOS. Typical applications include industrial Ethernet gateways, USB-CAN bridges, building-automation controllers, embedded web servers, and point-of-sale terminals. The integrated 10/100 MAC lets designers add Ethernet without an external controller, while USB OTG supports device, host and OTG roles for storage, charging or peripherals. When designing with this part, validate the 80 MHz operation against voltage and temperature (2.3-3.6V, -40 to +85C for the -80I industrial grade) and pay attention to the 121-ball TFBGA escape - place at least 4 layers with microvia-in-pad and a continuous ground plane under the BGA. This page synthesizes pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet.

USD $5,86 En stock

PIC32MX775F512L-80V/BG

PIC32MX775F512L-80V/BG - 80MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC32MX775F512L-80V/BG is a 32-bit MIPS M4K microcontroller running up to 80MHz, integrating 512KB of Flash program memory and 64KB of SRAM in a 121-ball TFBGA package (10x10mm). The device belongs to the PIC32MX5/6/7 family and adds a built-in 10/100 Mbit Ethernet MAC, USB-OTG, and dual CAN peripherals that target connected-embedded designs. Core logic operates from a 2.3V to 3.6V supply and the part offers up to 51 general-purpose I/O. A 32-bit microcontroller is a programmable processor that executes instructions from on-chip memory, exposes configurable peripherals, and serves as the central compute unit of an embedded system. Within the broader semiconductor hierarchy it sits inside the microcontroller family, which itself belongs to logic ICs, integrated circuits, and ultimately to the wider electronics component taxonomy. The PIC32MX5/6/7 family uses a Harvard-class MIPS32 core paired with Microchip's peripheral library, and is fully supported by the MPLAB Harmony integrated software framework, MPLAB X IDE, and XC32 compiler toolchain. This puts the PIC32MX775F512L-80V/BG in the application-processor tier of microcontrollers, with on-chip connectivity IP that historically required an external MAC plus PHY. Differentiating features include the integrated Ethernet MAC, USB-OTG full-speed controller, two independent CAN 2.0b modules, a 16-channel 10-bit 1 Msps ADC, and a parallel master port for external memory. DMA, five 16-bit timer/counters, and four IC SPI interfaces further offload the core. A 10-bit ADC combined with DMA enables deterministic analog sampling for motor, sensor, and power-conversion feedback loops. Typical deployments include industrial gateways, factory-automation controllers, automotive telematics modules, medical patient monitors, USB-OTG device or host peripherals, and Ethernet-attached data-acquisition nodes. The 512KB code region supports the TCP/IP stack plus application code without external boot memory, while dual CAN enables bridge-node access in a CAN-Ethernet gateway. Design considerations include signal integrity on the 80MHz LVPBA outputs, supply decoupling of the analog AVDD rail to preserve 10-bit ADC linearity, and thermal performance inside the 10x10mm TFBGA footprint for sustained Ethernet + USB workloads. This page synthesizes Microchip datasheet figures, distributor pricing from DigiKey and Mouser (as of 2026-10-03), drop-in alternative listings from Microchip's own cross-reference portal, and design notes not found in the manufacturer datasheet.

USD $6,80 En stock

PIC32MX775F512L-80V/PF

PIC32MX775F512L-80V/PF - 32-bit 80MHz MCU 512KB Flash 100-TQFP

The Microchip Technology PIC32MX775F512L-80V/PF is a 32-bit MIPS32 M4K PIC microcontroller IC delivering 80 MHz CPU performance with 512 KB (512K x 8) of Flash and integrated connectivity peripherals, housed in a 100-pin TQFP (14x14 mm) package. It features a 2.3V to 3.6V supply voltage range, 51 digital I/O ports, and full USB OTG, dual CAN, 10/100 Ethernet MAC, and multiple UART/SPI/I2C interfaces for embedded networking designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and on-chip peripherals. The PIC32MX5/6/7 family belongs to the 32-bit MCU category within Microchip's portfolio, sitting above 16-bit PIC24/dsPIC devices and below MIPS-based higher-end MPU/MPU lines. Its position in the taxonomy is: 32-bit MCU -> embedded microcontroller -> microcontroller IC -> semiconductor. Compared with 8-bit and 16-bit MCUs, 32-bit MCUs enable larger code size, higher throughput, RTOS support, and richer connectivity stacks. Key features of the PIC32MX775F512L include 512 KB of Flash program memory, 64 KB SRAM (typical PIC32MX775 spec - confirm with datasheet), 8 DMA channels, hardware crypto engine, and integrated 10/100 Mbps Ethernet MAC plus USB 2.0 Full-Speed OTG. The 100-pin TQFP package provides 51 user I/O and 5 dedicated timers/capture inputs. Industrial-grade operating temperature range supports harsh environments, and full MIPS32 instruction compatibility eases firmware portability. Typical applications include industrial Ethernet gateways, CAN-based automotive body controllers, USB peripherals, embedded web servers with MPLAB Harmony TCP/IP stack, and multi-protocol industrial sensor hubs. The combination of CAN + Ethernet + USB on a single die removes external PHY/transceiver complexity for connected-device designs. When designing with this MCU, ensure the 2.3-3.6V supply is regulated within tolerance, allocate 4-10 LED I/O for the USB D+/D- differential pair routing, and follow Microchip's hardware design checklist for the 100-pin TQFP land pattern. JTAG/ICSP programming access must be brought out for production programming. This page synthesizes distributor pricing, same-brand drop-in alternatives from the PIC32MX5/6/7 family, and practical design notes that go beyond the manufacturer datasheet summary to support both prototyping and volume sourcing decisions.

USD $8,95 En stock

PIC32MX775F512L-80V/PT

PIC32MX775F512L-80V/PT - 32-bit MCU, 512KB Flash, USB, CAN, Ethernet, 100-TQFP | Microchip

The Microchip Technology PIC32MX775F512L-80V/PT is a 32-bit MIPS32 M4K microcontroller (MCU) integrating 512 KB of Flash program memory and 64 KB of SRAM in a 100-pin TQFP (PT, 12x12 mm) package. It operates at up to 80 MHz, supplies 51 usable I/O pins, and runs from a 2.3 V to 3.6 V supply. The -80V speed grade and V temperature range make it suited to industrial-grade embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of on-chip peripherals. PIC32MX7xx devices sit in Microchip's PIC32 family, which is positioned between 8-bit PIC MCUs and 32-bit ARM Cortex-M parts. Within that family, PIC32MX775 specifically adds an integrated 10/100 Ethernet MAC, USB-OTG, and dual CAN controllers - features normally requiring external components on simpler MCUs. Key features include USB-OTG full-speed host/device, two CAN 2.0B modules, a 10/100 Mbps Ethernet MAC with MII/RMII interface, 16-channel 10-bit ADC at 1 Msps, five 16-bit timers, two I2C, two SPI, and a parallel master port. The PIC32MX775 implements the MIPS32 M4K core with single-cycle multiply, hardware multiply-accumulate, and a five-stage pipeline, enabling up to 1.56 DMIPS/MHz. A dedicated DMA controller offloads memory transfers from the CPU across peripherals. Architecturally, the part is built on a 0.25 µm flash process, with prefetch cache to hide Flash latency at high CPU clock rates. Peripherals are connected to the CPU via a multi-layer bus matrix that allows concurrent DMA and CPU traffic to SRAM and peripheral FIFOs. Typical applications include industrial Ethernet gateways, CAN-based automotive body controllers, USB peripherals (HID, CDC, MSD, audio class), PLCs, building-automation nodes, embedded web servers, and POS terminals. The combination of integrated Ethernet, USB-OTG, dual CAN, and 512 KB Flash removes the need for external PHY or interface ICs in many designs. Design tip: at 80 MHz and 3.3 V, full Flash read requires the prefetch cache enabled and one wait state. Place a 100 nF decoupling capacitor on every VDD/VSS pair and a 10 µF bulk capacitor near the regulator. The Ethernet MAC still requires an external PHY (e.g., LAN8720A, DP83848); the PIC32MX775 provides only the MAC layer. This page synthesizes distributor pricing, drop-in alternatives, and engineering guidance not found in the bare datasheet - including cross-vendor equivalents, same-family pin-compatible upgrades, and quantified thermal and power notes.

USD $7,45 En stock

PIC32MX775F512LT-80I/PF

PIC32MX775F512LT-80I/PF - 80MHz 512KB Flash MCU | Microchip

The Microchip Technology PIC32MX775F512LT-80I/PF is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 512 KB of Flash program memory and 64 KB of SRAM, housed in a 100-pin TQFP (14x14 mm) package. It integrates USB 2.0 (full-speed), two CAN modules, 8-channel DMA, 16-bit parallel master port, and 10/100 Ethernet MAC in the silicon. A 32-bit microcontroller (MCU) is a single-chip processor that integrates CPU core, program memory, data memory, and peripherals. The PIC32 family uses the MIPS32 M4K core, which places it in the broader taxonomy of MIPS-based 32-bit microcontrollers -> microcontrollers (MCU) -> embedded processors -> semiconductors. Compared with 8-bit or 16-bit MCUs, 32-bit devices like the PIC32MX775 enable higher computational throughput, larger addressable memory, and richer peripheral sets, making them suitable for connected embedded systems. Key features include 83 general-purpose I/O lines, five 16-bit timers/counters, two analog comparators, two UART modules, two SPI interfaces, two I2C buses, an analog-to-digital converter and a CTMU (Charge Time Measurement Unit). The integrated 10/100 Ethernet MAC and dual CAN 2.0B controllers give designers direct access to industrial and automotive networking without external PHY hardware. Industrial temperature range -40C to +85C supports harsh environment deployments. Typical applications include industrial Ethernet gateways, CAN-based automation controllers, USB peripherals and embedded web servers. The wide peripheral mix makes the PIC32MX775 well-suited to designers consolidating multiple legacy 8/16-bit MCUs into one 32-bit platform while preserving pin-compatible footprints within the PIC32MX family. When designing with this part, plan oscillator and decoupling layout early: place the 8 MHz primary crystal within 1 cm of the OSC1/OSC2 pins with short traces and guard ring, and add 0.1 uF + 10 uF decoupling near each VDD/VSS pin pair. Always reference the Microchip PIC32MX5XX/6XX/7XX family datasheet for configuration bit settings and peripheral pin mapping. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $8,20 En stock

Subcategorías

Productos (32725)