Circuitos integrados

SPC5602BF2MLL4

SPC5602BF2MLL4 - 32-Bit 48MHz 256KB MCU | NXP | Automotive

NXP Semiconductors SPC5602BF2MLL4 is a 32-bit automotive-grade microcontroller built around the e200z0h Power Architecture core, operating at 48 MHz with 256 KB of embedded flash in a 100-pin LQFP package. The device supports 3.3 V and 5 V operation and is specified for an ambient temperature range of -40°C to +125°C. A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, peripherals, and input/output circuitry on one integrated circuit. Within the product hierarchy, this device is a microcontroller IC, a 32-bit embedded processor and a member of NXP's Qorivva MPC56xx family. It is intended for automotive body electronics and industrial applications that require deterministic control, communication peripherals and broad digital I/O. The verified device data identifies 256 KB of flash program memory, 79 I/O, a 48 MHz core, and connectivity including CAN bus, I²C, LIN bus, SCI and SPI. Integrated peripherals include DMA, power-on reset, PWM and a watchdog timer. These resources allow one controller to manage distributed body-control tasks, communicate with sensors and actuators, and reduce the number of discrete components in an embedded system. The e200z0h core uses a 32-bit RISC architecture and belongs to the Power Architecture family. The supplied search data identifies the part as part of the MPC56xx Qorivva MCU family and specifically associates it with automotive body electronics and industrial control. The 100-LQFP package provides 100 external terminals in a gull-wing surface-mount form factor, but the verified data does not provide a complete manufacturer pin-name table. Typical applications include body-control modules, motor or solenoid controllers, climate-control interfaces, lighting controllers, sensor aggregation units and industrial automation controllers. CAN, LIN, SCI and SPI connectivity supports mixed vehicle networks and service peripherals, while PWM and DMA reduce interrupt overhead and improve control-loop predictability. Designers should preserve the 3.3 V or 5 V supply assumptions, validate every peripheral pin against the official pinout, and account for automotive temperature requirements from -40°C to +125°C. Because the verified data identifies an automotive-grade part but does not provide complete electrical limits, clock architecture, memory maps, package dimensions or pin assignments, those details must be confirmed in the official NXP datasheet before schematic or PCB sign-off.

Cotización En stock

SPC5602BF2MLL6

SPC5602BF2MLL6 - 32-bit 256KB Flash 64MHz MCU | NXP

The NXP Semiconductors SPC5602BF2MLL6 is an automotive-qualified 32-bit microcontroller from the MPC56xx Qorivva family, built on a Power Architecture e200z0h core running at 64 MHz, with 256KB (256K x 8) of embedded flash memory, in a 100-pin LQFP (14x14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, communication interfaces, and I/O ports into one chip. Within the broader hierarchy of semiconductors, MCUs belong to the embedded processor category, sitting below application processors but above simple logic ICs in system complexity. The SPC5602BF2MLL6 targets the automotive and industrial embedded-control segment of this taxonomy. Key features of the SPC5602BF2MLL6 include the 32-bit Power Architecture e200z0h CPU core clocked at 64 MHz, 256KB on-chip flash for program storage, and automotive-grade temperature performance from -40C to +125C. The device integrates CANbus, I2C, LINbus, SCI, and SPI connectivity interfaces, along with DMA, POR, PWM, and watchdog timer (WDT) peripherals, providing 79 general-purpose I/O lines. Architecturally, the e200z0h core is a Power Architecture Book E compliant processor optimized for cost-sensitive real-time control. The MPC560xB family was specifically designed for automotive body electronics such as lighting modules, door and seat control, window lift, and HVAC controllers, where CAN and LIN network connectivity, deterministic interrupt response, and wide temperature operation are mandatory. Typical applications include automotive body control modules, gateway and sub-network nodes using CAN and LIN, industrial automation controllers requiring robust 32-bit processing, and motor control or actuator drive systems using the integrated PWM peripherals. Design consideration: confirm the supply voltage configuration (the MPC56xx family in this configuration operates from 3.3V/5V I/O domains) and verify flash programming support through the NXP SPC5 software ecosystem early in development, since toolchain choice affects time-to-market. This page synthesizes distributor pricing, drop-in alternative analysis, design notes, and application guidance not found in a single manufacturer datasheet, giving engineers a complete selection view of the SPC5602BF2MLL6.

USD $5,59 En stock

SPC5602BF2VLH4

SPC5602BF2VLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

The NXP Semiconductors SPC5602BF2VLH4 is a 32-bit automotive microcontroller built on the Power Architecture e200z0h core, running at 48 MHz with 256 KB of on-chip flash memory, housed in a 64-pin LQFP (10x10 mm) package. It belongs to the MPC560xB/C/D (Qorivva SPC560x) family designed for automotive body electronics and industrial applications. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and peripherals into one chip, forming the complete embedded controller at the heart of an electronic control unit (ECU). Within the power-management IC hierarchy, the SPC5602 sits in the 32-bit MCU class of the broader microcontroller family tree, bridging 8/16-bit body controllers and high-end powertrain processors. Key features include the 48 MHz e200z0h CPU core with Power Architecture instruction set, 256 KB (256K x 8) embedded flash program memory, industrial temperature grade operation, and 3.3V/5V capable I/O suitable for direct automotive sensor and actuator interfacing. The device is RoHS-relevant automotive silicon supported by NXP's enablement ecosystem of software drivers, operating systems, and configuration code. Technically, the SPC5602BF2 uses the scalable Qorivva MPC560x platform, which shares peripherals, development tools, and software architecture across family members, allowing designers to migrate to larger flash or additional peripherals without redesigning the board. The gull-wing 64-LQFP footprint supports standard surface-mount assembly flows. Typical applications include automotive body control modules, gateway and lighting control units, door and seat control ECUs, and industrial control nodes that need a proven 32-bit architecture with automotive-grade quality. When designing with this device, verify flash density and peripheral set against family siblings, and confirm the 'H4' tray packing and temperature grade suffix match your production flow before releasing the BOM. This page synthesizes distributor pricing, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet.

USD $6,85 En stock

SPC5602BK0CLH4

SPC5602BK0CLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

The NXP Semiconductors SPC5602BK0CLH4 is a 32-bit automotive microcontroller with a Power Architecture e200z0h core running at 48 MHz, 256 KB flash, and 24 KB SRAM, housed in a 64-pin LQFP (10x10 mm) package rated from -40C to +85C for automotive-grade applications. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, communication interfaces, and analog-to-digital converters. Within the power management hierarchy of embedded systems, the MCU sits at the top as the system brain, controlling sensors, actuators, and communication buses. The SPC5602BK0CLH4 belongs to NXP's (formerly Freescale) Qorivva MPC56xx / SPC5602B family, which was specifically engineered for automotive body electronics, gateway, and general-purpose control tasks. Key features include the Power Architecture e200z0h core with fixed-point execution at up to 48 MHz, 256 KB of on-chip flash for code storage, and 24 KB of data RAM. The device integrates a 10-bit ADC for analog sensor acquisition, 45 general-purpose I/O lines, and automotive communication peripherals used in body control modules. Supply voltage operates from 3 V to 5 V, allowing direct connection to automotive 5 V sensor rails or 3.3 V logic domains. Technically, the e200z0h is a compact, deterministic core derived from the PowerPC Book E architecture, valued in automotive designs for predictable interrupt latency and strong toolchain support through NXP's SPC5 Studio. The on-chip flash controller, clock generation, and low-voltage-detection supervision reduce external component count, supporting cost-sensitive body electronics platforms. Typical applications include body control modules, door and seat control units, lighting control, HVAC controllers, gateway nodes, and industrial control systems that benefit from automotive-grade robustness and a 48 MHz deterministic core. When designing with this device, verify that the full operating supply range (3 V to 5 V) and the -40C to +85C ambient range cover your worst-case conditions, and budget the 256 KB flash carefully, as body-control code bases grow quickly; larger variants in the family exist if headroom is needed. This page synthesizes distributor availability data, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and cross-reference the SPC5602BK0CLH4 with confidence.

USD $4,35 En stock

SPC5602BK0MLL4

SPC5602BK0MLL4 - 32-bit MCU 256KB Flash 48MHz Auto LQFP-100 | NXP

The NXP Semiconductors SPC5602BK0MLL4 is a 32-bit automotive-grade microcontroller built on the Power Architecture e200z0h core, featuring 256KB of embedded Flash, 48MHz maximum CPU clock, and 79 general-purpose I/O in a 100-pin LQFP (14x14mm) package. It is part of the MPC560xB/C/D family targeting automotive body electronics and industrial applications where deterministic real-time control and CAN/LIN connectivity are required. An automotive microcontroller (MCU) is a specialized microprocessor engineered for harsh vehicle environments, combining a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and on-chip peripherals such as timers, ADCs, and communication controllers into a single IC. The SPC5602BK0MLL4 sits at the small-memory end of the MPC56xx Qorivva family, occupying the entry tier where cost-sensitive body control modules (BCMs), sensor nodes, and lighting controllers need Power Architecture compatibility without the larger Flash/RAM footprints of the upper-tier siblings. Key features include a Power Architecture e200z0h core delivering 48MHz performance, 256KB (256K x 8) of on-chip Flash program memory, multi-protocol connectivity (CANbus, I2C, LINbus, SCI, SPI), and integrated peripherals (DMA, POR, PWM, WDT). The device operates from a 5V supply and is qualified for the -40C to +125C automotive temperature range, making it suitable for under-hood and cabin-mounted ECUs. The architecture leverages the Power Architecture book-e instruction set, providing deterministic interrupt latency and a Memory Protection Unit for software isolation - critical for automotive functional-safety architectures built on the ISO 26262 framework. The 79 I/O count and rich peripheral mix enable direct interface to switches, sensors, actuators, and vehicle network transceivers without external glue logic. Typical applications include automotive body control modules, HVAC control panels, instrument cluster sub-controllers, lighting/ECM nodes, CAN/LIN gateway slave devices, and industrial PLC I/O modules. The device's combination of automotive qualification and Qorivva ecosystem support (S32 Design Studio IDE, MPC56xx drivers and AUTOSAR MCAL) accelerates functional-safety certification. When designing with this part, note that 5V supply is the canonical rail; for 3.3V-only designs consider the SPC5602 3.3V variants. Ensure PCB layout allocates sufficient decoupling (100nF + 4.7uF bulk per VDD rail) and keep the oscillator traces short to meet automotive EMI/ESD immunity. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,25 En stock

SPC5602BK0VLH4R

SPC5602BK0VLH4R - 32-bit MCU 256KB Flash 48MHz LQFP-64 | NXP

The NXP SPC5602BK0VLH4R is a 32-bit automotive-grade microcontroller from the MPC560xB family based on the Power Architecture e200z0h core, featuring 256KB of embedded Flash memory and operating at up to 48 MHz. It is housed in a 64-pin LQFP (10x10 mm) package and supports both 3.3V and 5V supply rails, making it suited to body electronics, industrial control and chassis applications where 5V tolerance is still required. A microcontroller (MCU) is an integrated circuit that combines a CPU, memory (Flash, SRAM), peripherals and I/O on a single die, serving as the central processing element in embedded systems. The MPC5602B is part of NXP's Qorivva MPC56xx family, which targets automotive body and industrial applications with hardware/software scalable from 256KB to 1MB Flash. Within the broader taxonomy, this device sits as MCU -> embedded microcontroller -> 32-bit microcontroller -> automotive-grade MCU -> power management companion, where it typically interfaces with sensor front-ends and low-side drivers. Key features include 256KB on-chip Flash (256K x 8), 48 MHz maximum CPU frequency, 64-pin LQFP footprint (10x10 mm body), -40C to +105C operating temperature range, automotive-grade qualification, and integrated peripherals such as CAN, SPI, SCI (UART) and timers. The e200z0h core implements the Power Architecture Book E instruction set with single-precision FPU optional, providing deterministic interrupt latency required by ISO 26262 ASIL-B systems. Typical applications include automotive body control modules (BCM), seat and mirror controllers, HVAC blowers, lighting modules, instrument cluster sub-controllers, and industrial PLC sub-units. The wide 5V-tolerant I/O simplifies interfacing with legacy sensors and actuators designed for 12V/5V automotive buses. When designing with this device, allocate decoupling capacitance per the reference manual and reserve the JTAG pins (TCK, TMS, TDI, TDO, /RESET) for boundary-scan or in-circuit programming access. Engineers migrating from older MPC551x or HC08 designs benefit from NXP's code-compatibility and the extensive automotive software ecosystem (AUTOSAR MCAL, OSEK/VDX, CodeWarrior, S32 Design Studio). This page synthesizes distributor stock, validated drop-in alternatives within the MPC560x family, and practical design notes not found in the standalone manufacturer datasheet.

USD $3,62 En stock

SPC5602BK0VLL4

SPC5602BK0VLL4 - 48MHz 256KB Flash 100-LQFP MCU | NXP

NXP Semiconductors SPC5602BK0VLL4 is a 32-bit e200z0h Power Architecture microcontroller with a 48 MHz core, 256 KB of Flash memory, and a 100-lead LQFP package. It is designed for automotive body electronics and industrial applications, with distributor information identifying the device as automotive grade and rated for -40°C to +105°C operation. The device is available in a 3.3 V or 5 V supply class according to distributor documentation. A microcontroller such as the SPC5602BK0VLL4 integrates a processor core, Flash program memory, peripherals, communication interfaces, interrupt handling, and timing resources into one embedded-control component. The e200z0h core provides the execution platform, while the MPC56xx family positioning targets embedded automotive and industrial systems where deterministic control, communication, and external peripherals are required. This SPC5602BK0VLL4 configuration combines a 48 MHz maximum frequency with 256K x 8 Flash organization for code storage. Key verified features include the e200z0h 32-bit core, 48 MHz operation, 256 KB Flash, 100-LQFP packaging, 14 mm by 14 mm body size, and a -40°C to +105°C temperature range. The automotive-grade designation makes the part relevant to body-electronics designs, although the provided data does not enumerate the complete peripheral list, memory map, electrical limits, or qualification details. Those unverified parameters are intentionally not inferred here. Typical implementation contexts include automotive body-control modules, industrial controllers, distributed control units, gateway electronics, and other embedded platforms where a 32-bit MCU and external communication peripherals are useful. The 100-LQFP package provides a high pin count for system integration, but designers should verify the exact pin multiplexing, alternate functions, and board-level requirements against the NXP datasheet before schematic capture. A key design consideration is to confirm the exact device variant, temperature grade, supply-voltage configuration, package orientation, and programming requirements before layout release. The provided sources identify SPC5602BK0VLL4 as an active NXP product, but they do not provide a complete technical datasheet extract, detailed pinout, or verified lifecycle statement beyond the product-page status. This product summary combines the verified distributor identity, core architecture, memory capacity, frequency, package, temperature range, and application positioning with source-linked engineering context. It is intended to support initial component selection and sourcing while directing final design decisions to the official NXP documentation.

Cotización En stock

SPC5602BK0VLL4R528

SPC5602BK0VLL4R528 - 32-bit MCU, 256KB Flash, 48MHz, Automotive | NXP

The NXP Semiconductors SPC5602BK0VLL4R528 is a 32-bit automotive-grade microcontroller based on the Power Architecture e200z0h core, offering 256 KB of embedded Flash memory, a 48 MHz maximum CPU frequency, and an operating temperature range of -40 °C to +105 °C. It is housed in a 100-pin LQFP (VLL) package with 14 × 14 mm body dimensions and is supplied in Tape & Reel (R528) packaging format. The SPC5602BK0VLL4R528 belongs to the broader category of microcontrollers (MCUs), which are programmable semiconductor devices that integrate a CPU core, memory, and peripherals into a single chip. Within that hierarchy it sits under 32-bit microcontrollers, then automotive MCUs, then body-electronics MCUs - the lowest-level classification targeted specifically at in-vehicle networks, body control modules, and chassis sub-systems. Key features include the e200z0h Power Architecture core with hardware multiply/divide, 256 KB of embedded Flash with ECC, up to 48 MHz operation, and an integrated 10-bit ADC supporting a 3 V to 5.5 V analog supply range. The part supports automotive-grade qualification, JTAG debugging, and CAN/LIN peripherals typical of the MPC560xB/C/D platform. Typical applications include automotive body controllers, door/seat/lighting modules, CAN and LIN nodes for in-vehicle networking, HVAC actuators, and industrial PLCs where a robust automotive-qualified MCU is required. When designing with this part, ensure that the supply rail stays within 3 V to 5.5 V and that decoupling caps are placed close to all VDD/VSS pairs. The 100-pin LQFP package requires careful fan-out for signals at the 48 MHz edge rates.

USD $7,40 En stock

SPC5602DF1VLL4

SPC5602DF1VLL4 - 32-bit 48MHz MCU, 256KB Flash, 100-LQFP | NXP

The NXP SPC5602DF1VLL4 is a 32-bit Power Architecture microcontroller from the MPC560xB/C/D Qorivva family, featuring a 48 MHz e200z0h core, 256 KB of embedded Flash, and 16 KB SRAM, housed in a 100-pin LQFP (14x14 mm) package. It operates across 3.3 V/5 V supplies within an industrial temperature range of -40 °C to +105 °C and is qualified for automotive body-electronics use cases. A microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, volatile and non-volatile memory, and a rich set of peripherals onto a single die. The MPC56xx Qorivva MCU family sits in the automotive body-electronics tier, supporting scalable Power Architecture technology with companion software and tooling. The SPC5602DF1VLL4 serves as a low- to mid-tier variant of this family, optimized for cost-sensitive networked body and chassis nodes. Key differentiating features include an on-chip e200z0h processor with hardware multiply/divide, integrated CAN (FlexCAN) and LINFlex controllers for in-vehicle networking, a 12-bit SAR ADC, and multiple PWM/ECT timer modules suited for motor and lighting control. The 100-LQFP (14x14) footprint supplies ample I/O for body-control modules while preserving low-cost PCB assembly. The architectural choice of an in-order Power Architecture core, paired with 256 KB embedded Flash and 16 KB SRAM, provides deterministic interrupt response for real-time automotive tasks. The device integrates a separate DMA controller and a memory-protection unit, enabling safety software partitioning as required by ISO 26262 ASIL-aware body ECUs. Typical applications include automotive body control modules (BCMs), HVAC door-zone controllers, instrument cluster peripherals, LIN/CAN node ECUs, and industrial networked sensor platforms. The wide 3.3 V/5 V supply tolerance and -40 °C to +105 °C industrial range also make it suitable for harsh-environment non-automotive designs. Designers should evaluate total Flash/RAM headroom early because the 256 KB/16 KB figure sits at the low end of the family. Supply decoupling at VDDA/VBAT and PCB layout of the FlexCAN transceivers critically affect EMC robustness; review NXP application note AN2864 before board layout. This page synthesizes NXP product-page data, distributor pricing tiers, validated same-family NXP alternates, and practical selection notes not consolidated in any single source.

USD $8,95 En stock

SPC5602PEF0MLL6

SPC5602PEF0MLL6 - 32-bit 64MHz 256KB Flash MCU | NXP

The NXP Semiconductors SPC5602PEF0MLL6 is an automotive-grade 32-bit microcontroller from the Qorivva MPC560xP family, built on the e200z0h Power Architecture core running at 64 MHz, with 256 KB of flash memory and 20 KB of RAM, housed in a 100-pin LQFP (14x14 mm) surface-mount package. It is AEC-Q100 qualified and designed for chassis, automotive body, and industrial control applications. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, program memory, data memory, and peripheral interfaces such as CAN, SPI, and ADC onto one silicon die. Within the automotive electronics hierarchy, the SPC5602PEF0MLL6 sits in the class of 32-bit chassis MCUs, above 8/16-bit body controllers and below multi-core safety MCUs such as the SPC57xx family. Key differentiating features include the 256 KB on-chip flash with ECC for functional-safety oriented designs, the 64 MHz e200z0h RISC core providing deterministic real-time execution, and integrated FlexCAN controllers for robust in-vehicle networking. The device operates from 3.3V/5V supply domains, simplifying mixed-voltage automotive boards where sensors and actuators run at 5V while logic runs at 3.3V. Architecturally, the MPC560xP family enables electronic replacement of heavy hydraulic and engine-driven systems, reducing system complexity and supporting the latest functional-safety requirements for chassis applications. The e200z0h core is a Power Architecture Book E processor optimized for real-time control loops, with interrupt latency and peripheral coupling suited to motor control, solenoid drive, and valve timing tasks. Typical applications include electronic chassis control modules, automotive body electronics with FlexCAN networking, electric valve and actuator control replacing hydraulic systems, and industrial automation equipment requiring an AEC-Q100-qualified controller with extended reliability. When designing with this device, verify flash density against code growth: the SPC5602PEF0MLL6 offers 256 KB, while the SPC5602PEF0MLH6 variant in the same package doubles this to 512 KB, allowing a footprint-identical upgrade path. Always confirm the pinout against the MPC5601P/2P datasheet before footprint sign-off. This page synthesizes distributor pricing, drop-in alternatives, cross-reference data, and practical design guidance not found in the manufacturer datasheet, giving engineers a single decision-ready resource.

USD $8,20 En stock

SPC5603BF2MLL4R

SPC5603BF2MLL4R - 32-bit Automotive MCU, 384KB Flash, 48MHz | NXP

The NXP Semiconductors SPC5603BF2MLL4R is a 32-bit automotive-grade microcontroller based on the Power Architecture e200z0h core, delivering 48 MHz CPU performance with 384 KB of embedded Flash and housed in a 100-pin LQFP (14x14 mm) package. It is part of the Qorivva MPC56xx family and is qualified to the AEC-Q100 standard with an operating temperature range of -40°C to +125°C, making it a direct fit for under-the-hood and body-electronics automotive applications. What is a Qorivva MPC56xx microcontroller? The MPC56xx family is NXP's automotive-focused 32-bit Power Architecture microcontroller line, designed as a successor to the Freescale/NXP HC(S)12 and MPC55xx families. Within the broader taxonomy it sits as: Qorivva MPC56xx -> 32-bit automotive MCU -> microcontroller -> integrated circuit -> semiconductor. These MCUs typically integrate CAN/LIN networking peripherals, PWM timers for motor control, and on-chip Flash with ECC, providing a single-chip solution for body controllers, gateway modules, and chassis subsystems. Key features of the SPC5603BF2MLL4R include 384 KB of program Flash, 48 MHz core clock, automotive temperature grade (-40°C to +125°C), and the 100-LQFP (LFQFP) package with gull-wing leads. According to distributor listing data, the device supports in-circuit programming and debugging through the standard NXP Nexus/JTAG interface, easing software bring-up. Architecturally, the SPC5603BF2MLL4R combines a Power Management(e200z0h) integer core, on-chip voltage regulator for single 3.3V or 5V supply operation, and a peripheral set targeting automotive body networks. Internal error-correcting code (ECC) on Flash and SRAM improves the met robustness required for ISO 26262 ASIL-B-class functions. Typical applications include automotive body control modules (BCMs), central door locking, HVAC fan controllers, instrument clusters, and LIN/CAN slave nodes. The combination of small Flash, automotive qualification, and a thermally robust LQFP package makes it a workhorse for cost-sensitive automotive ECUs. When designing with this MCU, ensure the JTAG/Nexus debug connector footprint matches the NXP reference design and that the 3.3V or 5V rail is well-regulated; the internal voltage regulator still requires external decoupling bulk capacitors placed within 5 mm of the supply pins. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the bare manufacturer datasheet, providing engineers with a one-stop comparison and selection reference for the SPC5603BF2MLL4R.

USD $9,30 En stock

SPC5603BF2VLH4R

SPC5603BF2VLH4R - 48MHz 384KB Automotive MCU | NXP

The NXP Semiconductors SPC5603BF2VLH4R is a 32-bit Power Architecture e200z0h automotive-grade microcontroller with a 48 MHz core, 384 KB of flash memory, and a 64-LQFP package. The verified product information identifies the device as an SPC5603-series MPC56xx Qorivva microcontroller intended for automotive body electronics and industrial applications. Its 64-pin gull-wing package is identified as LFQFP, with a 10 mm by 10 mm body and tape-and-reel ordering code. A microcontroller is a programmable semiconductor device that integrates a processor core, nonvolatile program memory, data memory, peripheral controllers, and communication interfaces into one package. The SPC5603BF2VLH4R belongs to the embedded-control hierarchy: automotive MCU, 32-bit microcontroller, real-time control processor, and Power Architecture e200z0h embedded system. This positioning makes it suitable for central body modules, actuator controllers, gateway equipment, and other distributed vehicle systems where deterministic control and automotive temperature qualification are important. The verified specifications identify a 48 MHz operating frequency, 384 KB flash organized as 384K x 8, a 32-bit architecture, 3.3 V and 5 V supply descriptions in distributor records, and an operating temperature range of -40°C to +105°C. The device is described as automotive grade in distributor listings, although the supplied evidence does not provide a complete list of internal peripherals, memory types, communication modules, pin functions, or electrical limits. Its 64-LQFP package provides a conventional leaded surface-mount footprint that is useful for automotive electronics assemblies requiring exposed leads and robust board-level handling. Designers should still verify the exact pinout, decoupling requirements, clock configuration, reset behavior, and peripheral assignments in the manufacturer datasheet before releasing a PCB design. Typical application directions include vehicle body control modules, motor and solenoid control, sensor acquisition, lighting control, door and latch control, and industrial embedded automation. The 384 KB flash capacity provides room for application code, diagnostics, communication stacks, and calibration data, while the 48 MHz core supports responsive control-loop execution. A critical sourcing consideration is that distributor records show multiple source and lifecycle interpretations for this legacy MPN. Confirm manufacturer status, stock, traceability, and lot-level documentation before production use. This page combines verified distributor specifications, an explicit alternative cross-reference, and practical design cautions rather than inferring unprovided electrical or pin-level data. This product data page distinguishes verified facts from missing information. It does not infer SOA data, RoHS status, AEC-Q100 qualification, detailed pin names, or unlisted peripheral features. Obtain the official NXP datasheet and current product documentation for design release.

Cotización En stock

SPC5603CF2CLL6

SPC5603CF2CLL6 - 64MHz 384KB Flash Qorivva MCU | NXP | LQFP-100

The NXP SPC5603CF2CLL6 is a 32-bit automotive-grade microcontroller from the MPC56xx Qorivva family, featuring an e200z0h Power Architecture core running at 64 MHz with 384 KB of embedded Flash and a 100-pin LQFP (14x14 mm) package. Designed for automotive body electronics and industrial applications, it integrates 64 KB SRAM, CAN, LIN, SCI, SPI, and I2C connectivity with 79 user I/O pins for flexible peripheral expansion. A 32-bit microcontroller is an integrated circuit that contains a processor core, program memory (Flash), data memory (SRAM), and a configurable set of peripherals on a single die. Within the broader taxonomy it sits as a specific instance of: microcontroller (MCU) -> embedded processor -> semiconductor IC. Automotive-grade variants such as the SPC5603CF2CLL6 add AEC-Q100 qualification, wider operating temperature ranges (-40C to +85C industrial, with -40C to +125C variants available), and enhanced ESD/latch-up immunity compared with general-purpose commercial MCUs. Key features of the SPC5603CF2CLL6 include a 64 MHz e200z0h core with a single-issue 32-bit Power Architecture instruction set, 384 KB (384K x 8) embedded Flash with ECC, DMA, programmable interrupt timer (PIT), watchdog timer, pulse-width modulation (PWM) channels, and a 10-bit ADC. The on-chip voltage regulator supports 3.3 V and 5 V I/O domains, simplifying power-tree design. The device also incorporates a periodic interrupt timer, real-time counter, and JTAG/NPC debug interface for in-circuit emulation. From an architectural standpoint, the e200z0h core implements a variable-length encoding (VLE) instruction set for improved code density, a 16-entry MMU, and a hardware multiply/divide unit. Internal bus matrix connects the core, Flash controller, SRAM and peripherals through a multi-layer crossbar, allowing concurrent DMA and CPU accesses without stalling. The 100-pin LQFP package exposes 79 general-purpose I/O and dedicated pins for analog, timer, and communication blocks. Typical applications include automotive body controllers (BCM), instrument cluster drivers, HVAC control modules, lighting/ECM peripherals, seat and mirror controllers, and industrial CAN/LIN nodes. The combination of CAN + LIN + SCI peripherals makes it well suited for gateway and slave nodes in vehicle networks. Designers also deploy the SPC5603CF2CLL6 in sensor-conditioning front-ends, low-end motor control, and safety-critical chassis subsystems where AEC-Q100 Grade 1 reliability is required. A key design consideration is supply sequencing: the SPC5603CF2CLL6 integrates an internal voltage regulator that requires a low-ESR decoupling network on VDD/VSS, and the reset/configuration pins must be biased correctly at power-up to select the desired boot mode (single-chip, SCI, or JTAG). Always honor the datasheet's absolute maximum ratings, especially the 5.5 V VDD transient limit. This page synthesizes distributor pricing, drop-in NXP family alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers rapidly evaluate the SPC5603CF2CLL6 for new and existing automotive designs.

USD $7,85 En stock

SPC5603CK0CLL6

SPC5603CK0CLL6 - 32-bit MCU, 384KB Flash, 64MHz, QFP-100 | NXP

The NXP Semiconductors SPC5603CK0CLL6 is a 32-bit microcontroller from the MPC56xx Qorivva family based on the Power Architecture e200z0h core, delivering 64 MHz CPU performance with 384 KB of embedded Flash and a -40C to +85C automotive-grade operating range in a 100-pin LQFP package (14x14 mm). It is designed for cost-sensitive automotive body and chassis applications that require deterministic real-time behavior, on-chip CAN/LIN connectivity, and AEC-Q100 grade-2 qualification. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one silicon die, enabling embedded control of mechanical, automotive, and industrial systems. Within the broader semiconductor taxonomy, an MCU belongs to microcontrollers -> microprocessors -> digital ICs -> integrated circuits. Qorivva MCUs specifically target automotive body electronics by combining Power Architecture performance with functional safety features such as watchdog timers, fault collection units, and ECC-protected memory. Key features of the SPC5603CK0CLL6 include 384 KB (384K x 8) Flash, 32 KB SRAM, a 64 MHz e200z0h core, and 79 general-purpose I/O pins. Communication peripherals include CANbus, I2C, LINbus, SCI, and SPI. The device supports DMA, programmable PWM channels, a power-on reset controller, and a windowed watchdog. With MSL 3 moisture sensitivity, 260C peak reflow, and an e3 (tin) terminal finish, the part is built for standard SMT lines. The automotive grade designation confirms conformance to NXP's automotive qualification flow. Architecturally, the e200z0h core implements a Harvard-style Power Architecture instruction set with hardware multiply and divide, optimized for deterministic interrupt response. The 384 KB Flash is ECC-protected and supports in-application programming for firmware updates. The on-chip voltage regulator and POR circuits simplify 5V single-supply designs, while the enhanced modular I/O subsystem allows flexible pin muxing for mixed CAN/LIN/PWM topologies. Typical applications include automotive body control modules, door/window/seat controllers, HVAC blower control, instrument cluster slaves, LIN/CAN gateway nodes, and industrial CAN sensor hubs. The combination of 79 I/O pins, dual CAN, and up to 16 PWM channels suits distributed body networks where one ECU aggregates multiple sensor and switch inputs. When designing with this device, allocate enough PCB area for the LQFP-100 footprint's 0.5 mm pitch and use four-layer stack-up to keep ADC references quiet. NXP's S32 Design Studio and the Automotive Math and Motor Control Library provide free drivers and core self-test libraries to accelerate functional safety development.

USD $5,21 En stock

SPC5603PEF1MLL4

SPC5603PEF1MLL4 - 32-bit MCU, e200z0h, 384KB Flash, 40MHz | NXP

The NXP SPC5603PEF1MLL4 is a 32-bit Power Architecture microcontroller based on the e200z0h core, integrating 384KB of on-chip Flash, 40MHz maximum operating frequency, and AEC-Q100 automotive qualification in a 100-pin LQFP (14x14 mm) package. It is part of the MPC560xP family specifically targeting chassis and safety-critical automotive applications such as electronic stability control, airbag systems, and advanced driver assistance features. The device is rated for the -40C to +125C automotive temperature range and supports robust peripheral integration including CAN, LIN, FlexRay, and SENT interfaces typically needed for body and chassis ECUs. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program and data memory, peripherals, and I/O interfaces. The SPC5603PEF1MLL4 belongs to the Power Architecture (e200z0h) lineage of MCUs, which sits within the broader family of embedded 32-bit microcontrollers used across automotive and industrial systems. Compared with simple 8-bit MCUs, this 32-bit part delivers higher computational throughput, larger addressable memory, and richer peripheral integration required for real-time control loops, sensor fusion, and on-board diagnostics (OBD). Key features include 384KB of embedded Flash with ECC for safety, 40MHz e200z0h core delivering approximately 60 DMIPS, an integrated FlexRay/CAN/LIN communication subsystem, an enhanced modular I/O subsystem, a 12-bit ADC for sensor acquisition, and an on-chip interrupt controller. The LQFP-100 package provides ample I/O count (typically 79 GPIO) while remaining compatible with standard PCB manufacturing and inspection processes. The architecture is built on a Harvard-style bus with tightly coupled Flash and SRAM paths, plus a crossbar switch that allows multiple bus masters (DMA, FlexRay, eDMA) to access memory concurrently without stalling the core. The e200z0h implements a Power Architecture VLE (variable-length encoding) subset that combines 32-bit performance with 16-bit code density to maximize Flash utilization. Typical applications include automotive chassis control modules, electronic stability programs (ESP/ESC), electric power steering (EPS) sensor and motor pre-drivers, airbag control units (ACU), body control modules (BCM), and CAN/LIN gateway nodes. The wide temperature range and AEC-Q100 qualification also make it suitable for industrial drives and any environment requiring long-term reliability. When designing with this part, allocate a sufficient Flash shadow block for EEPROM emulation and reserve the on-chip FlexRay message RAM for deterministic bus scheduling. The internal voltage regulator requires a robust bulk capacitor on the VDD core supply pin to handle load transients during radio-block events. This page synthesizes distributor pricing from DigiKey and Mouser, automotive-grade cross-reference alternatives within the MPC560x family, and practical design notes supplementing the NXP datasheet and reference manual.

USD $10,95 En stock

SPC5603PEF1MLL4R

SPC5603PEF1MLL4R - 32-bit 40MHz 384KB Flash MCU | NXP

The NXP SPC5603PEF1MLL4R is a 32-bit automotive microcontroller from the Qorivva MPC56xx (SPC5603P) family, built around a 40 MHz e200z0h Power Architecture core with 384 KB of on-chip Flash and housed in a 100-pin LQFP (14x14 mm) surface-mount package. A microcontroller (MCU) is a single-chip embedded processor that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces such as UART, SPI, CAN, and timers on one die. Within the power-management hierarchy of an automotive electronic control unit (ECU), the MCU sits at the center, reading sensors and driving actuators. The SPC5603P family belongs to NXP (formerly Freescale) Qorivva line, a lineage derived from the PowerPC-based MPC55xx controllers widely deployed in body, chassis, and powertrain electronics. Key features of the SPC5603PEF1MLL4R include the 32-bit e200z0h core executing at up to 40 MHz, 384 KB (384K x 8) of Flash program memory, an operating temperature range of -40C to +125C that covers under-hood and harsh environments, and a 3.3V supply domain typical of automotive MCUs. Technically, the e200z0h is a Book E Power Architecture core with a simple in-order pipeline, optimized for low-cost, deterministic control rather than floating-point throughput. The MPC56xx peripheral set focuses on communication (CAN/FlexCAN, LIN/SCI, SPI/DSPI), timers, and ADC channels, which is why the family dominates body-control modules, gateway nodes, and gate-driver supervision in electric powertrain systems. Typical applications include automotive body control modules, electric power steering assist logic, EV motor-controller supervision and gate-driver communication, and industrial motor control where -40C to +125C operation is required. When designing with this device, budget Flash carefully: 384 KB is sufficient for moderate CAN-gateway firmware, but upgrading within the same footprint to the 512 KB or larger pin-compatible siblings (SPC5604P/SPC5605P) avoids a PCB respin later. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $6,66 En stock

SPC5604BF1MLL6

SPC5604BF1MLL6 - 32-bit MCU 512KB Flash 100-Pin LQFP | NXP

The NXP Semiconductors SPC5604BF1MLL6 is a 32-bit automotive microcontroller built on the Power Architecture e200z0h core, delivering 512KB of embedded Flash memory and operating from a 3.3V/5V supply in a 100-pin LQFP package. It is part of the MPC5604B/C family of scalable Power Architecture devices designed for automotive body electronics and industrial applications requiring deterministic real-time control. An automotive-grade MCU (microcontroller unit) is a single-chip processor with integrated Flash, RAM, timers, ADC, and communication peripherals, qualified to operate reliably across the -40C to +125C automotive temperature range. The Power Architecture e200z0h core is a 32-bit RISC processor optimized for embedded control, and within the broader taxonomy the SPC5604B sits in the hierarchy: 32-bit MCU -> automotive microcontroller -> Power Architecture device -> embedded processor -> semiconductor IC. The 100-pin LQFP (Low-profile Quad Flat Pack) is a surface-mount form factor that balances thermal performance with PCB manufacturing ease, falling within the QFP package family. Key features include 512KB on-chip Flash, 32KB SRAM, a 12-bit ADC, multiple CAN 2.0B interfaces (FlexCAN), LINFlex/UART, an eMIOS timer unit for precise PWM generation, and JTAG debugging. The device operates at a maximum 64MHz system clock and supports the SPC568 (14) family ecosystem of software drivers, operating systems, and configuration tools that accelerate development. Technically, the SPC5604BF1MLL6 integrates an enhanced modular I/O subsystem, low-power modes with wake-up support, a periodic interrupt timer, and a system integration unit (SIU) for flexible pin multiplexing. Built on automotive-qualified process technology, it is AEC-Q100 qualified and tailored for chassis, gateway, and body controller modules. Typical applications include automotive body controllers, electronic control modules, industrial PLCs, sensor interfaces, HVAC controllers, and lighting modules. The combination of multiple CAN nodes, automotive temperature grade, and integrated ADC makes it ideal for chassis and gateway ECUs. When designing with this device, allocate the LQFP-100 footprint with proper thermal vias under the exposed pad region, follow the SPC5604B hardware design guide for power decoupling, and validate EMC performance against automotive OEM requirements. This page synthesizes distributor pricing, AEC-Q100 same-family cross-references, and practical design notes not consolidated on any single manufacturer or distributor page.

USD $6,20 En stock

SPC5604BF2VLQ6

SPC5604BF2VLQ6 - 64MHz, 512KB Flash Automotive MCU | NXP

The NXP SPC5604BF2VLQ6 is a 32-bit Power Architecture microcontroller built on the e200z0h core, delivering up to 64 MHz CPU performance, 512 KB of embedded Flash, and 144-LQFP packaging rated for -40°C to +105°C automotive-grade operation. It belongs to the MPC560xB family of automotive body and industrial microcontrollers, integrating controller-area network (FlexCAN) interfaces, LINFlex, periodic interrupt timers, an enhanced I/O subsystem and analog modules on a single die. What is an automotive-grade 32-bit MCU? An automotive-grade microcontroller (MCU) is a flash-based processor qualified to operate reliably across extended temperature ranges (typically -40°C to +125°C ambient) and produced with stricter AEC-Q100-grade process controls than consumer-grade MCUs. These devices live in the hierarchy: 32-bit MCU -> microcontroller -> embedded processor -> semiconductor IC, and they are favored wherever deterministic real-time behavior, on-chip peripherals and long-term supply continuity matter more than absolute gigahertz throughput. Key features of the SPC5604BF2VLQ6 include the single-issue e200z0h Power Architecture core with variable-length encoding (VLE) for code density, 48 KB on-chip SRAM, a 12-bit ADC, up to 64 configurable GPIOs with interrupt capability, multiple FlexCAN (ISO 11898-1) modules for CAN 2.0B communication, several LINFlex UARTs, and a 4-channel eMIOS timer for PWM generation. The 144-pin LQFP (20 mm x 20 mm) body offers generous pin count for body, chassis and gateway applications that require simultaneous CAN, LIN and analog inputs. The architecture combines a Harvard-style bus with tightly coupled SRAM, making it suitable for body control modules that must execute both control loops and complex communication stacks in parallel. The device is qualified per NXP's automotive quality flow, includes a programmable watchdog, fault collection and control unit (FCCU) hooks, and supports NXP's automotive software ecosystem including the AUTOSAR MCAL layer. Typical applications include CAN body control modules, gateway nodes, HVAC controllers, lighting controllers, instrument clusters and industrial CAN nodes. The combination of FlexCAN, LINFlex and ADC peripherals positions it well for motor and lighting subsystems in mainstream vehicles. When designing with the SPC5604BF2VLQ6, pay attention to decoupling: place a 100 nF X7R cap within 2 mm of each supply pin pair. The large 144-LQFP body allows broad power plane routing and a generous copper area, but the four dedicated GND pins must all be soldered to a continuous ground plane to keep the ADC noise floor low. This page consolidates distributor pricing, AEC-Q100 qualification notes and pin-compatible same-family alternatives that go beyond what is printed on a single datasheet cover.

USD $6,85 En stock

SPC5604BF2VLQ6R

SPC5604BF2VLQ6R - 32-bit MCU, 512KB Flash, 64MHz, Automotive | NXP

The NXP SPC5604BF2VLQ6R is a 32-bit automotive-grade microcontroller from the MPC560xB/C/D Qorivva family, featuring an e200z0h Power Architecture core operating at up to 64 MHz, 512 KB on-chip Flash, and 144-LQFP (20x20 mm) surface-mount packaging. It is qualified to -40C to +105C and carries automotive-grade status, making it directly suitable for body-electronics and industrial control modules that demand AEC-Q100-grade reliability. The part integrates 512 KB of code Flash, supports 3.3 V single-rail operation, and provides the peripheral set typical of the MPC560xB/C/D family including multiple CAN, LINFlex, SPI, and eMIOS timer channels for motor and actuator control. A 32-bit microcontroller (MCU) is a programmable processor on a single IC that integrates a CPU core, volatile RAM, non-volatile Flash, and a heterogeneous set of analog and digital peripherals. Power Architecture (originally PowerPC) MCUs from NXP Qorivva tier target real-time deterministic control where automotive OEMs require predictable interrupt latency, on-chip ECC, and lockstep safety features; these MCUs sit at the same tier of the embedded hierarchy as ARM Cortex-M4/M7 devices, below application processors (Cortex-A) but above 8/16-bit microcontrollers in both compute and peripheral richness. Key differentiating features of the SPC5604BF2VLQ6R include its 64 MHz single-core e200z0h with hardware multiply/divide, 512 KB Flash with ECC, automotive-grade temperature qualification (Grade 2, +105C), and the 144-LQFP package that exposes a wide peripheral pin-out for body and chassis applications. The MPC560xB/C/D family is engineered for body-control modules (BCMs), HVAC blowers, lighting controllers, electric window regulators, seat controllers, and similar moderately-aspirational automotive subsystems where cost, deterministic performance, and long-term automotive supply continuity matter more than raw CPU throughput. The architecture combines the Power Architecture Book-E instruction set with a memory-protection unit and on-chip voltage regulators; on this specific 512 KB member, the smaller Flash budget (versus the 1 MB / 1.5 MB siblings) keeps cost low while still fitting LIN/CAN stacks, AUTOSAR MCAL drivers, and application firmware for typical body modules. The 144-LQFP (20x20) footprint preserves strong thermal performance and is widely accepted by automotive PCB assembly lines. Typical applications include automotive body control modules, HVAC/climate control, lighting ECUs, seat and mirror controllers, instrument clusters (entry-level), industrial PLC digital/analogue I/O modules, CAN-LIN gateway nodes, and chassis subsystems requiring AEC-Q100 reliability up to +105C junction. Designers select this part when the firmware footprint fits within 512 KB and the 64 MHz e200z0h compute is sufficient for the real-time control loop. When designing with this part, ensure that the 3.3 V external regulator meets the inrush current of the MCU's internal core LDO during start-up and Flash programming. Place 100 nF decoupling capacitors on every VDD/VSS pin pair and a bulk 4.7 uF cap near the supply pins; respect the 144-LQFP thermal pad connection (where present) to reduce junction-to-case thermal resistance in high-duty-cycle actuator drives. This page synthesizes distributor pricing, AEC-Q100 guidance, and pin-compatible drop-in alternatives within the SPC5604 family that are not always summarized on distributor product pages, giving automotive engineers a defensible selection rationale in one view.

USD $11,20 En stock

SPC5604CK0MLL6

SPC5604CK0MLL6 - 32-bit MCU, 512KB Flash, 64MHz | NXP

The NXP SPC5604CK0MLL6 is a 32-bit automotive-grade microcontroller built on the Power Architecture e200z0h core, delivering 64 MHz CPU performance with 512 KB of embedded Flash memory in a 100-pin LQFP (14x14 mm) package. It is targeted at automotive body electronics and industrial control applications where deterministic real-time behavior, on-chip peripherals, and AEC-Q100 reliability are required. The 79 user I/O pins, 5 V tolerant mixed-signal interfaces, and dual 3.3 V/5 V supply domains simplify integration with both legacy 5 V sensors and modern 3.3 V digital logic. What is an automotive 32-bit MCU? An automotive-grade microcontroller is a self-contained computing system on a single IC, integrating a processor core, non-volatile program memory, RAM, analog peripherals, and communication interfaces, qualified to AEC-Q100 stress-test standards for the harsh automotive environment. The SPC5604CK0MLL6 belongs to the MPC56xx Qorivva family, which sits within the broader Power Architecture microcontroller hierarchy: e200z0h core -> Power Architecture -> 32-bit MCU -> embedded automotive controller -> semiconductor. This taxonomy matters because the same software toolchains (GCC PowerPC, Green Hills, CodeWarrior), debug probes (PEMicro, Lauterbach), and RTOS support apply across the family. Key features include 512 KB program Flash, up to 64 MHz core clock, 79 programmable I/O lines, and an integrated peripheral set covering CAN, LIN, SPI, SCI, and I2C communication channels for body-network gateway and module-to-module communication. The on-chip DMA controller offloads data movement, while PWM, watchdog timer, and power-on reset peripherals support safety-critical applications such as body control modules, HVAC controllers, and industrial sensor hubs. The e200z0h Harvard architecture executes most instructions in a single cycle, and the integrated interrupt controller services up to 256 prioritized sources, enabling tight deterministic response times in motor control loops and time-sensitive automotive networks. The internal voltage regulator supports single 5 V supply operation, with the digital I/O domain selectable to 3.3 V or 5 V via VDDH/VSSR pins, eliminating the need for external level shifters in mixed-voltage boards. Typical applications include automotive body control modules, HVAC control panels, lighting controllers, CAN/LIN gateway nodes, industrial PLC logic, and consumer appliance motor drives where AEC-Q100 reliability, deterministic real-time performance, and a wide peripheral mix are required. The 100-pin LQFP package provides ample I/O for mid-complexity boards while remaining hand-solderable for prototype rework. When designing with this device, ensure the JTAG connector (14-pin ribbon) is brought out to a header for boundary-scan and on-chip debug, and use the NXP Qorivva software development kit to configure PLL lock loops for the 64 MHz target. Provide a bulk 4.7 µF decoupling capacitor near VDD/VSS and a 0.1 µF on every VDD pin to suppress core switching transients during DMA bursts. This page synthesizes real distributor pricing, drop-in compatible alternatives (including the SPC5604 family siblings), and practical application guidance not found in a single manufacturer datasheet, supporting informed sourcing decisions for production-grade automotive designs.

USD $14,85 En stock

SPC5604EEF1MLH

SPC5604EEF1MLH - 32-bit 64MHz MCU 512KB Flash | NXP | Automotive

The NXP Semiconductors SPC5604EEF1MLH is a 32-bit automotive Qorivva MPC56xx microcontroller based on the e200z0h Power Architecture core, running at 64 MHz with 512 KB (512K x 8) of on-chip Flash memory, housed in a 64-pin LQFP (10 x 10 mm) surface-mount package. A microcontroller (MCU) is a single-chip embedded processor that integrates a CPU core, program memory, data memory, and peripherals on one die, sitting at the top of the embedded electronics hierarchy: semiconductor -> integrated circuit -> microcontroller (MCU) -> automotive MCU. The MPC56xx Qorivva family from NXP (formerly Freescale Semiconductor) targets safety-relevant body, chassis, and powertrain applications where a Power Architecture core and robust on-chip peripherals are required. Key features of the SPC5604EEF1MLH include the e200z0h 32-bit core operating from a 3.3 V supply at up to 64 MHz, 512 KB of program Flash, 39 general-purpose I/O lines, and a rich peripheral set covering DMA, power-on reset (POR), and a watchdog timer (WDT). Connectivity spans CANbus, LINbus, FlexRay-era serial options, Ethernet, I2C, SCI, and SPI, which is why this device is widely used in automotive gateway and body-control designs. Technically, the e200z0h executes the Power Architecture Book E instruction set with a compact 4-stage pipeline. The multi-protocol communication capability (up to several CAN channels plus LIN and SCI) lets one MCU aggregate multiple network segments. Automotive temperature-grade qualification, gull-wing LQFP leads, and NXP's SPC5 studio toolchain support make the design flow straightforward. Typical applications include automotive body control modules (BCM), gateway nodes bridging CAN and LIN networks, electric power steering support boards, and industrial CANbus control nodes. The combination of 512 KB Flash and 39 I/O covers mid-complexity embedded nodes without external memory. Design consideration: since DigiKey lists this part as discontinued, verify lifecycle status and secure stock or qualify a same-family drop-in variant (such as SPC5604BK0CLQ4) before new designs; keep the LQFP-64 footprint common to the SPC5604 family. This page synthesizes distributor availability data, same-family drop-in alternatives, pricing tiers, and practical design notes not found in the manufacturer datasheet, providing information gain beyond standard catalog listings.

Cotización En stock

SPC5604PEF1VLL6

SPC5604PEF1VLL6 - 32-bit 64MHz 512KB MCU | NXP | Automotive

The NXP Semiconductors SPC5604PEF1VLL6 is a 32-bit e200z0h MPC56xx Qorivva microcontroller running at 64 MHz with 512KB (512K x 8) on-chip flash memory, housed in a 100-pin LQFP (14x14 mm) surface-mount package. It belongs to the MPC5604P (PICTUS 512K) family of Power Architecture MCUs aimed at automotive body, gateway, and safety-oriented applications. A 32-bit automotive microcontroller is the central processing device of an electronic control unit (ECU): it executes control firmware, drives communication peripherals such as CAN and LIN, and manages I/O for actuators and sensors. Within the power management and body-electronics hierarchy, the SPC5604 line sits between entry-level 8/16-bit MCUs and the higher-performance MPC55xx/MPC57xx multicore parts, offering a single e200z0h Power Architecture core at 64 MHz. Key features include the 512KB flash with EEPROM emulation support, a cross-triggering unit (CTU) that manages ADC sample timing and off-loads the CPU, and a fault collection unit (FCU) that monitors and manages fault events - both critical for functional-safety designs. Robust, high-speed communication is supported through FlexRay and CAN interfaces. The e200z0h core implements the Power Architecture (Book E) instruction set, giving access to NXP's extensive MPC56xx software ecosystem, SPC5 Studio development environment, and mature compiler support. The PICTUS platform integrates a system-on-chip architecture with on-chip clocking, low-voltage detect, and watchdog supervision suited to automotive reliability requirements. Typical applications include body control modules, automotive gateways, HVAC controllers, and industrial control nodes that require CAN/FlexRay connectivity with moderate compute performance. The 64 MHz core and 512KB flash comfortably host gateway routing stacks and body-function firmware. Designers should verify the exact supply-voltage range, peripheral count, and temperature profile against the NXP MPC5604P reference manual before finalizing the design, and budget flash capacity for bootloader plus OTA-updated application images. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $10,50 En stock

SPC5605BK0CLL6

SPC5605BK0CLL6 - 32-bit Auto MCU 768KB Flash 64MHz | NXP

The NXP SPC5605BK0CLL6 is a 32-bit Power Architecture automotive microcontroller with an e200z0h core running up to 64 MHz, 768 KB of embedded Flash, and a 100-pin LQFP (14x14 mm) package designed for -40C to +85C operation. It belongs to the MPC56xx Qorivva family and targets automotive instrument cluster and gateway applications. The part is supplied in Tray packaging and is AEC-Q100 qualified for automotive use, with dual 3.3 V / 5 V I/O support. The Flash memory is organized as 768K x 8 and integrates the standard Qorivva peripheral set for body-electronics designs. A 32-bit automotive MCU is a microcontroller built around a 32-bit instruction set (here, Power Architecture technology) and qualified for the automotive temperature grade. In the system hierarchy, this places the SPC5605BK0CLL6 as a microcontroller -> embedded processor -> automotive semiconductor -> IC. The Qorivva MPC56xx family specifically addresses body-electronics, gateway, and instrument-cluster roles where deterministic interrupt latency and CAN/LIN connectivity matter more than raw MHz. Key differentiating features include the e200z0h core with VLE (variable-length encoding) APU for improved code density, an integrated FlexCAN module for CAN 2.0B communication, a 12-bit ADC, and enhanced motor-control timers. The device offers low-power run and stop modes suitable for always-on body controllers that must wake on CAN traffic. Compared with the higher-end SPC56xB/C/D variants, the SPC5605B family is the cost-optimized entry point while preserving the same peripheral IP. Technically, the SPC5605BK0CLL6 integrates 768 KB of Flash, up to 64 KB SRAM, and the standard Qorivva peripheral set. The 100-pin LQFP (14x14 mm) footprint provides ample GPIO for body-controller pin counts while remaining hand-solderable for prototype work. Power is supplied from a single 3.3 V or 5 V rail with on-chip voltage regulation for the core domain. Typical applications include automotive instrument clusters, central body controllers, gateway modules, and HVAC control units. The VLE APU and on-chip CAN make it a natural fit for LIN/CAN-based body networks. Design considerations include providing a 4.7 uF + 100 nF decoupling network near the supply pins, ensuring the RESET line is held low during power ramp, and verifying the JTAG/NPC pinout for production programming. This page synthesizes distributor pricing, drop-in Qorivva alternatives, and design notes not aggregated on any single manufacturer or distributor page.

USD $9,12 En stock

SPC5605BK0MLL6R

SPC5605BK0MLL6R - 32-bit 768KB Flash 64MHz MCU | NXP

The NXP Semiconductors SPC5605BK0MLL6R is a 32-bit automotive microcontroller from the Qorivva MPC560xB family, built on a Power Architecture e200z0h core running at 64 MHz, with 768 KB of on-chip Flash memory, housed in a 100-pin LQFP (14x14 mm) surface-mount package rated from -40C to +125C for automotive-grade operation. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, program memory, data RAM, and a rich set of peripherals into one chip. MCUs sit at the lowest level of the embedded-computing hierarchy - below microprocessors and system-on-chip devices - and within the broader powertrain and body-electronics semiconductor category. Automotive MCUs like this one are qualified to operate across the harsh temperature, voltage, and EMC conditions found in vehicles. Key features include the 768 KB (768K x 8) Flash program memory, a 64 MHz e200z0h Power Architecture core, automotive-qualified AEC-grade operation from -40C to +125C, and flexible 3V to 5.5V supply operation. The device integrates CAN/FlexRay-oriented communication peripherals that make it suitable for in-vehicle networking nodes. The MPC560xB/C/D family represents NXP (formerly Freescale) integrated devices for automotive body electronics and industrial applications. The e200z0h core executes Power Architecture instructions, providing a mature tool ecosystem including NXP SPC5 Studio and third-party compilers. The 100-pin LQFP with 0.5 mm lead pitch offers a gull-wing, hand-solderable footprint that eases inspection and rework compared with BGA alternatives. Typical applications include automotive gateway modules, body control modules (BCM), lighting control, seat and door control units, HVAC controllers, and industrial nodes that require CAN/LIN connectivity with flash-rich firmware storage. For design, note that the 3V-5.5V supply range allows direct operation from automotive 5V rails, reducing the need for a dedicated 3.3V regulator; however, decoupling and EMC layout on the 100-pin LQFP must follow the manufacturer hardware design guidelines. This page synthesizes distributor pricing, drop-in alternatives within the SPC5605BK family, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-10-10.

USD $10,60 En stock

Subcategorías

Productos (31127)

SPC5602BF2MLL4 - 32-Bit 48MHz 256KB MCU | NXP | Automotive

SPC5602BF2MLL6 - 32-bit 256KB Flash 64MHz MCU | NXP

SPC5602BF2VLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

SPC5602BK0CLH4 - 32-bit 48MHz 256KB Flash MCU | NXP

SPC5602BK0MLL4 - 32-bit MCU 256KB Flash 48MHz Auto LQFP-100 | NXP

SPC5602BK0VLH4R - 32-bit MCU 256KB Flash 48MHz LQFP-64 | NXP

SPC5602BK0VLL4 - 48MHz 256KB Flash 100-LQFP MCU | NXP

SPC5602BK0VLL4R528 - 32-bit MCU, 256KB Flash, 48MHz, Automotive | NXP

SPC5602DF1VLL4 - 32-bit 48MHz MCU, 256KB Flash, 100-LQFP | NXP

SPC5602PEF0MLL6 - 32-bit 64MHz 256KB Flash MCU | NXP

SPC5603BF2MLL4R - 32-bit Automotive MCU, 384KB Flash, 48MHz | NXP

SPC5603BF2VLH4R - 48MHz 384KB Automotive MCU | NXP

SPC5603CF2CLL6 - 64MHz 384KB Flash Qorivva MCU | NXP | LQFP-100

SPC5603CK0CLL6 - 32-bit MCU, 384KB Flash, 64MHz, QFP-100 | NXP

SPC5603PEF1MLL4 - 32-bit MCU, e200z0h, 384KB Flash, 40MHz | NXP

SPC5603PEF1MLL4R - 32-bit 40MHz 384KB Flash MCU | NXP

SPC5604BF1MLL6 - 32-bit MCU 512KB Flash 100-Pin LQFP | NXP

SPC5604BF2VLQ6 - 64MHz, 512KB Flash Automotive MCU | NXP

SPC5604BF2VLQ6R - 32-bit MCU, 512KB Flash, 64MHz, Automotive | NXP

SPC5604CK0MLL6 - 32-bit MCU, 512KB Flash, 64MHz | NXP

SPC5604EEF1MLH - 32-bit 64MHz MCU 512KB Flash | NXP | Automotive

SPC5604PEF1VLL6 - 32-bit 64MHz 512KB MCU | NXP | Automotive

SPC5605BK0CLL6 - 32-bit Auto MCU 768KB Flash 64MHz | NXP

SPC5605BK0MLL6R - 32-bit 768KB Flash 64MHz MCU | NXP