CI de interfaz
Subcategorías
Productos (1022)
TUSB8041ARGCR - 4-Port USB 3.1 Hub Controller | Texas Instruments
The Texas Instruments TUSB8041ARGCR is a 4-port SuperSpeed USB 3.1 Gen1 hub controller operating at 5 Gbps, housed in a 64-pin VQFN (RGC) 9x9 mm package with exposed thermal pad. It provides upstream USB 3.0 connectivity and four downstream ports, each capable of SS (5 Gbps), HS (480 Mbps), FS (12 Mbps), and LS (1.5 Mbps) signaling. A USB hub is a USB class-defined device that expands a single upstream USB port into multiple downstream ports while managing power, enumeration, and transaction translation. The TUSB8041 family sits within the broader hierarchy of USB controllers, peripheral interface ICs, and interface ICs in the semiconductor taxonomy. It supports USB Type-A downstream ports and is commonly used to add four ports to a system with a single USB 3.0 upstream port. Key features of the TUSB8041ARGCR include support for USB Battery Charging (BC) 1.2 charging downstream ports, integrated 5-V tolerant I/O, per-port power switching with individual enable control, and configuration via GPIO, I2C, or SMBus interfaces. The device also supports USB Type-C port-reversal logic when used with an external Type-C controller, and offers pin-selectable upstream port configuration. Internal spread-spectrum clocking reduces EMI on the SuperSpeed signal paths. The architecture combines a USB 2.0 hub controller and a USB 3.0 hub controller on a single die, sharing common configuration logic. Per-port SuperSpeed PHY blocks operate independently, and traffic scheduling is managed by a hardware transaction translator. The device enumerates as a compound USB hub and supports standard USB hub class commands plus vendor-specific commands for charger-port behavior and GPIO control. Typical applications include USB expansion in desktop motherboards, docking stations, automotive infotainment head units, industrial PCs, monitor USB hubs, and embedded computing platforms that require multiple downstream USB 3.0 ports from a single host connection. The wide industrial temperature support enables in-vehicle and factory-floor deployment. When designing with this part, observe the PCB layout guidelines in the datasheet: keep the SuperSpeed differential pairs matched to 85 ohm differential impedance, decouple each VBUS supply pin with a 0.1 uF ceramic capacitor, and place the upstream port common-mode chokes close to the connector. Daisy-chained hubs are supported up to 5 tiers per USB specification. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical PCB layout notes not consolidated in the manufacturer datasheet alone.
TUSB8041ARGCT - 4-Port USB 3.1 Gen1 Hub Controller | Texas Instruments
The Texas Instruments TUSB8041ARGCT is a 4-port SuperSpeed 5-Gbps USB 3.1 Gen1 hub controller in a 64-pin VQFN (RGC) 9x9 mm package with an exposed thermal pad. The device integrates four downstream USB ports that simultaneously support Low-Speed, Full-Speed, High-Speed, and SuperSpeed signaling, delivering up to 5 Gbps per downstream port while presenting a single upstream USB 3.1 Gen1 Type-A or Type-C interface to the host. A USB hub controller is an interface IC that multiplies a single upstream USB port into multiple downstream ports while preserving protocol compliance, port power switching, and per-port status reporting. Hubs occupy a fixed position in the USB device-class hierarchy between the host controller root hub and downstream peripherals. Modern SuperSpeed hubs additionally embed PHYs and link-training state machines so legacy USB 2.0 traffic and 5 Gbps SuperSpeed traffic are bridged transparently across the same physical connector stack. The TUSB8041ARGCT provides per-port battery-charging detection, downstream-port power-enable controls routed through GPIO, and over-current flag inputs that simplify USB Type-A VBUS switching designs. Configuration is achieved through pin-strap modes, OTP ROM, an external I2C EEPROM, or an I2C/SMBus slave interface for VID, PID, and custom-string descriptors. The integrated 1.1 V core LDO and 3.3 V I/O supply mean only a single external 3.3 V rail is required for the hub itself. Typical applications include desktop and laptop docking stations, retail POS terminals, industrial PCs, USB 3.0/3.1 port replicators, automotive infotainment hubs, and embedded systems that fan out a single Type-C upstream port into multiple USB Type-A ports. The -40C to +85C industrial temperature range supports deployment in factory automation and vehicle environments. When designing with the TUSB8041ARGCT, route the SuperSpeed differential pairs (USB3_TX/RX) for 85 ohm differential impedance with intra-pair length matching within 150 mil, and provide an external 24 MHz crystal with the datasheet-recommended load capacitors. Place the upstream port ESD protection array adjacent to the USB connector and verify the bulk-decoupling ESR budget against the 5V VBUS load step on hot-plug events. This page synthesizes distributor pricing from DigiKey and Arrow, cross-references the TUSB8041A 'A' revision orderability codes (RGC = tape-and-reel, RGT = tray), and provides drop-in alternatives plus design notes not collected in any single datasheet document.
TUSB8041IPAPRQ1 - Automotive 4-Port USB 3.0 Hub | Texas Instruments
The Texas Instruments TUSB8041IPAPRQ1 is an automotive-grade, four-port, SuperSpeed 5-Gbps USB 3.0 hub controller in a 64-pin HTQFP (PAP) 10x10 mm package with exposed thermal pad, qualified to AEC-Q100 standards and operating across -40C to +85C. It supports simultaneous SuperSpeed, Hi-Speed, Full-Speed and Low-Speed upstream connections while delivering full backward compatibility on every downstream port. A USB hub controller is a class of interface IC that aggregates one upstream USB port into multiple downstream ports, managing enumeration, power switching, transaction translation and battery-charging detection across every port. The TUSB8041 sits in a hierarchy of USB Type-C and USB-C hub ICs, which themselves belong to the broader interface ICs and connectivity category within mixed-signal semiconductors. The Q1 suffix designates AEC-Q100 qualification, meaning the device is engineered and tested for the temperature, vibration and reliability stresses of in-vehicle electronics such as infotainment head units, telematic control units and rear-seat entertainment modules. Key specifications include four downstream ports, integrated USB 2.0 hub with multi-translation support, configurable via I2C, SMBus, GPIO and pin straps, and 1.1V / 3.3V dual-rail operation. The PAP variant of the family uses the 64-HTQFP footprint (10 mm x 10 mm) and offers broad flexibility for USB Type-C deployments when paired with a downstream crosspoint switch or PD controller. Typical applications include automotive head-unit USB expansion, rear-seat USB charging hubs, telematic USB pass-through, factory-floor USB test rigs and embedded computing platforms that need multiple USB-3 connections from a single root port. Because the device supports per-port power switching via the USB specification and individual over-current flags, designers can implement ganged or individual port power policies directly through hardware strap settings. When evaluating USB-3 hub alternatives, confirm that any candidate supports simultaneous SuperSpeed on all four ports, matches the 64-HTQFP land pattern, retains the I2C/SMBus configuration interface and meets AEC-Q100 grade-2 or stricter temperature targets. Note that 3.3 V supply noise from upstream regulators must remain below the threshold documented in TI's USB-3 hub electrical spec section, otherwise link-training jitter on SuperSpeed pairs can rise substantially.
TUSB8041IRGCT - 4-Port USB 3.0 Hub 5Gbps VQFN-64 | Texas Instruments
The Texas Instruments TUSB8041IRGCT is a four-port SuperSpeed USB 3.0 hub controller delivering 5 Gbps per port, housed in a 64-pin VQFN (RGC, 9x9 mm) package and rated for -40C to +85C industrial operation. A USB 3.0 hub controller is an integrated circuit that fans a single upstream SuperSpeed USB link out to multiple downstream ports, handling enumeration, transaction translation, and power management transparently to the host. Hub controllers sit in the USB interconnect tier of the system I/O hierarchy: host controller -> hub controller -> downstream devices, bridging the gap between a PC or embedded host and the peripherals it must serve. The TUSB8041 supports USB 3.0 SuperSpeed (5 Gbps) operation on all four downstream ports while remaining backward compatible with USB 2.0 and USB 1.1 devices on the same ports. It provides GPIO, I2C, and SMBus interfaces for configuration and status monitoring, allowing designers to customize hub behavior, set port modes, and read fault status in embedded systems. The industrial temperature rating (-40C to +85C) of the TUSB8041I variant makes it suitable for deployments beyond office-climate conditions. Architecturally, the device integrates the SuperSpeed hub repeater, USB 2.0 hub engine, and configuration ROM/EEPROM loading logic in a single die. Configuration can be performed via an external serial EEPROM or through the SMBus/I2C host interface, eliminating external glue logic. Integrated charge-pump and linear regulators generate the internal core supply from a single 3.3 V rail, simplifying power tree design. Typical applications include docking stations, port replicators, industrial PC and HMI USB expansion, embedded computing boards, and test and measurement instrumentation that requires multiple robust SuperSpeed ports from one upstream connection. Design consideration: USB 3.0 is a multi-gigabit differential signaling standard, so the 90-ohm differential impedance routing, length matching, and AC-coupling capacitor placement for the SuperSpeed pairs dominate signal integrity; place the device close to both the upstream connector and EEPROM, and follow the layout guidelines in the manufacturer datasheet. This page synthesizes verified distributor data, drop-in alternatives, pricing tiers, and practical design notes not found in the manufacturer datasheet alone, with pricing references stated as of 2026-09-03.
TUSB8041RGCR - 4-Port USB 3.0 Hub 5Gbps | Texas Instruments
The Texas Instruments TUSB8041RGCR is a four-port SuperSpeed USB 3.0 hub controller delivering 5-Gbps data rates per port, powered from dual 1.1V and 3.3V supplies and housed in a 64-pin VQFN (RGC) package measuring 9x9 mm with an exposed pad. A USB hub controller is an integrated circuit that fans out a single upstream USB connection into multiple downstream ports, handling enumeration, packet routing, and power management per the USB 3.0 specification. Within the system hierarchy it sits at the interface-IC layer, bridging the USB physical layer and the host controller of a computer, docking station, or embedded processor. Key features include four downstream SuperSpeed ports supporting 5 Gbps, backward compatibility with USB 2.0 full-speed and high-speed traffic, and configuration via GPIO, I2C, or SMBus interfaces for flexible SMBus-based platform integration. The device supports battery charging scenarios and standard hub power management, and TI offers both commercial (0C to 70C) and industrial (-40C to 85C) temperature grades in the same 64-pin RGC footprint. Architecturally, the TUSB8041 integrates the SuperSpeed repeater/retimer functions and hub transaction logic on a single die, using internal PLL-based clocking to regenerate the 5-Gbps link. The dual-rail 1.1V core / 3.3V I2V supply scheme reduces core power while maintaining signaling compliance, and the exposed-pad VQFN package provides low-inductance ground return for the high-speed differential pairs. Typical applications include PC motherboards and docking stations, monitors and displays with integrated USB hubs, industrial PCs requiring multiple USB 3.0 ports, and self-powered or bus-powered peripheral hubs. The 5-Gbps throughput makes it suitable for external storage, video capture, and camera aggregation. When designing with the TUSB8041, maintain 90-ohm differential impedance on the SuperSpeed pairs, keep them short and matched, and decouple both the 1.1V and 3.3V rails with low-ESR ceramics close to the pins. Configuration strapping or an I2C EEPROM must be present for non-default VID/PID settings. This page synthesizes distributor pricing, temperature-grade alternatives, and practical design notes not found in the manufacturer datasheet, verified as of 2026-09-03.
TUSB8043RGCT - 4-Port USB 3.1 Gen1 Hub Controller | Texas Instruments
The Texas Instruments TUSB8043RGCT is a 4-Port SuperSpeed USB 3.1 Gen1 hub controller supporting 5.0 Gbps signaling on downstream ports, housed in a 64-pin VQFN (RGC) 9x9 mm package. It integrates USB HID to I2C bridging, allowing host-side configuration of an attached EEPROM without an external bridge chip. The device supports full-speed, high-speed, and SuperSpeed USB operation across all four ports. A USB 3.1 hub is a connectivity expansion device that multiplies one upstream USB port into four downstream USB ports while maintaining protocol-aware traffic management. In the hierarchy of USB silicon, the TUSB8043 sits between USB 2.0 hubs (480 Mbps legacy) and USB 3.2 Gen2 (10 Gbps) hubs, serving the dominant consumer, docking-station, and embedded segment where 5 Gbps SuperSpeed is sufficient and power/area efficiency matter. Key features include per-port transaction translators (TTs) for full-/high-speed traffic, USB Battery Charging specification 1.2 support, integrated USB 2.0 PHY and SuperSpeed PHY per port, and configurable I2C/SMBus access through the HID endpoint. The device draws from a single 3.3 V supply rail and uses an external 25 MHz crystal, simplifying board layout. The RGC VQFN package exposes a thermal pad for heat spreading in sealed enclosures. Architecturally, the TUSB8043 implements a multi-RTL pipeline that schedules USB isochronous, interrupt, bulk, and control transfers independently per port, with split transactions across the 5 Gbps SuperSpeed lane for upstream traffic. Its hardware HID-to-I2C bridge maps vendor-specific USB control requests to I2C writes on the firmware-configured address, enabling platform designers to configure downstream peripherals from the host without an additional MCU. Typical applications include Thunderbolt and USB-C docking stations, industrial PCs and factory workstations, monitor bases with multiple USB peripherals, embedded computing platforms, point-of-sale terminals, and USB expansion cards. With USB-IF compliance built into the silicon, the TUSB8043 also powers medical imaging carts and test instrumentation where certified interoperability is mandatory. Designers should remember that downstream port power-enable and current-limit control require external TPS2041B/TPS2051B load switches; the TUSB8043 itself does not source VBUS. The 25 MHz reference must be a fundamental-mode crystal with ±50 ppm tolerance, and DP/DN traces on each downstream port require 90 Ω differential impedance matching to USB-IF compliance masks. This page aggregates distributor pricing, drop-in equivalents, and application-level design guidance drawn from the manufacturer datasheet and field reference designs, going well beyond a single-source product listing.
TUSB9261-Q1 - USB 3.0 to SATA Bridge AEC-Q100 | TI
The Texas Instruments TUSB9261-Q1 is an automotive-qualified, ARM Cortex-M3 microcontroller-based USB 3.0 to Serial ATA (SATA) bridge delivered in a 64-pin HTQFP package rated for -40C to +85C operation. It provides the hardware and firmware needed to implement a USB Attached SCSI Protocol (UASP)-compliant mass storage device, bridging HDDs, SSDs, optical drives, and other SATA 1.5-Gbps or SATA 3.0-Gbps devices to a SuperSpeed USB 3.0 host. A bridge IC is a dedicated interface converter that sits between two different bus protocols and translates transactions between them. Within the interface IC hierarchy (bridge -> USB interface controller -> interface IC -> semiconductor), the TUSB9261-Q1 belongs to TI's second generation of SuperSpeed USB-to-SATA bridges, specifically qualified for automotive applications per AEC-Q100, with a device CDM ESD classification of Level C3 as the noted exception. Key features include an embedded ARM Cortex-M3 processor core running TI firmware for UASP compliance, native support for SATA 1.5-Gbps and 3.0-Gbps device classes, and USB 3.0 SuperSpeed 5-Gbps connectivity on the host side. UASP support delivers significantly higher command queuing efficiency than legacy BOT (Bulk-Only Transport), reducing latency and improving throughput with modern SSDs. Integrated PHYs reduce external component count and BOM cost. The Cortex-M3 architecture allows TI to update bridge firmware, adding features and fixing interoperability issues without hardware changes, which is valuable for long-lifecycle automotive programs. AEC-Q100 qualification supports infotainment, telematics, and diagnostic ports where USB-attached storage must survive automotive temperature and ESD environments. Typical applications include automotive infotainment USB storage ports, in-vehicle diagnostic data loggers with SSD storage, and external HDD/SSD docking designs requiring automotive grade qualification. Design consideration: this device is flash-based firmware dependent; plan for firmware update provisions (I2C/EEPROM boot) in the PCB layout, and observe the datasheet note regarding SATA pin swapping documented on the TI E2E forum before finalizing routing.
TVP5146M2PFP - 10-bit NTSC/PAL/SECAM Video Decoder | TI HTQFP-80
The Texas Instruments TVP5146M2PFP is a 10-bit high-quality single-chip digital video decoder that digitizes and decodes all popular baseband analog video formats - including NTSC, PAL, SECAM composite, S-Video, component RGB and YPbPr - into digital component video, housed in an 80-pin PowerPAD HTQFP package (12x12 mm). It integrates Macrovision detection, a 5-line adaptive comb filter, SCART support, and four 30 MSPS 10-bit ADC channels, replacing multiple discrete decoder/filter ICs in mainstream consumer video designs. A digital video decoder is a mixed-signal IC that converts legacy analog broadcast and consumer video signals into a digital YCbCr or RGB pixel stream for downstream processing by a scalar, encoder, SoC, or capture ASIC. Within the broader taxonomy of mixed-signal ICs, the TVP5146M2 belongs to the video decoder family, which sits below video processors and above simple video amplifiers in the signal-chain hierarchy. Multi-standard support (NTSC M/N/4.43, PAL B/G/H/I/M/N/60, SECAM) allows one hardware design to ship worldwide without regional BOM variants. Key differentiating specifications include four integrated 10-bit ADCs sampling at up to 30 MSPS, an integrated 5-line adaptive comb filter for superior chroma/luma separation, Macrovision copy-protection detection, and 12 analog front-end inputs that multiplex automatically - composite, S-Video, component YPbPr, RGB, and SCART - under software control via I2C. Programmable gain, clamp, and offset on each channel allow direct connection to consumer-grade video sources without external op-amps. Architecture is built around TI's analog front-end, 10-bit ADC array, comb filter, and digital formatter block. The decoder outputs 8/16-bit ITU-R BT.601/BT.656 or 20-bit ITU-R BT.1120 digital component video, and supports both 2x and 1x oversampling modes. An internal color-space converter generates YCbCr and RGB outputs simultaneously, reducing host CPU overhead and shortening time-to-market for set-top box, DVR, and capture-card designs. Typical applications include set-top boxes and DVRs decoding composite or component broadcast video, USB video capture cards capturing VHS/DVD or legacy consoles, video conferencing codecs, surveillance DVRs, and automotive rear-seat entertainment head units that digitize external composite sources. The wide input tolerance also suits broadcast monitor walls and medical imaging reference inputs. When laying out a PCB, allocate a solid ground plane beneath the PowerPAD and stitch the exposed pad with at least 9 thermal vias to the inner ground layer. Use 75 ohm-controlled-impedance routing on all analog video inputs to preserve 2T pulse response, and place anti-alias RC networks within 5 mm of each analog pin. Decouple both 1.8 V and 3.3 V rails with 0.1 uF X7R ceramics in parallel with 10 uF bulk capacitors at the supply pins. This page synthesizes distributor pricing from Mouser and DigiKey, drop-in same-package alternatives, and practical design notes (PCB layout, thermal pad, decoupling) not found in the manufacturer datasheet alone, giving engineers a one-stop reference for the TVP5146M2PFP.
TVP5147M1PFPR - 10-bit NTSC/PAL/SECAM Video Decoder | TI HTQFP-80
The Texas Instruments TVP5147M1PFPR is a 10-bit high-quality single-chip digital video decoder that digitizes and decodes NTSC, PAL, and SECAM analog composite, S-Video, and component YPbPr signals into digital component video (YCbCr 4:2:2), housed in an 80-pin HTQFP (PFP) PowerPAD package with 12x12 mm body. According to TI product page, it integrates two 10-bit ADCs, a 5-line adaptive comb filter, and Macrovision 1.x/2.x detection, providing a complete analog front-end plus decoder in a single device. What is a video decoder? A video decoder is a type of interface IC that converts analog baseband video signals (composite CVBS, Y/C, or YPbPr component) into digital ITU-R BT.656 or BT.601 video streams. Within the broader taxonomy, video decoders belong to encoders/decoders/converters in interface ICs, sitting between analog video sources (tuners, cameras, DVD players) and digital video processors (DSPs, SoCs, FPGAs). They are essential building blocks in LCD TV/Monitor designs where legacy analog video must be displayed on digital panels. The TVP5147M1's key differentiating features include a hardware Macrovision detection circuit (Macrovision 1.x and 2.x compliant), a 5-line adaptive comb filter for superior luminance/chrominance separation in NTSC/PAL, automatic gain control with peak/average modes, and TI's proprietary chroma transient improvement (CTI) and luminance peaking circuitry. The device supports ten analog input channels selected via I2C, programmable H/V sync outputs, VBI data slicing for teletext/closed caption, and outputs ITU-R BT.656, BT.601, or raw VBI data over an 8- or 16-bit parallel interface. A single 27 MHz reference clock serves all standard video formats. Architecturally, the TVP5147M1 combines two 10-bit, 30 MSPS ADCs with a programmable automatic gain control, a chroma demodulator with subcarrier PLL, a 5-line comb filter, and a digital output formatter. Analog supplies are 1.8 V (analog) and 3.3 V (I/O), while the digital core runs from an internally regulated 1.8 V supply. The HTQFP-80 PowerPAD package provides a thermal pad that must be soldered to a ground plane for adequate heat dissipation; PowerPAD operation lowers junction temperature and improves long-term reliability in always-on consumer equipment. Typical applications include LCD TV and LCD monitor analog video inputs, set-top boxes archiving analog broadcasts, digital video recorders (DVR), video capture cards for PCs, in-car rear-seat entertainment displays, and security DVR systems. The Macrovision detection makes it suitable for licensed playback equipment where copy protection circuitry is mandated by content owners. When designing with this device, ensure the PowerPAD is soldered to a continuous ground copper pour with multiple thermal vias to maximize heat flow. Use a 27 MHz crystal with low jitter (<50 ps RMS) to minimize pixel-clock jitter on the digital output, which directly impacts downstream display quality. Decouple the 1.8 V analog and 3.3 V I/O rails with 0.1 uF and 10 uF ceramic capacitors placed as close to the supply pins as practical. This page synthesizes distributor pricing, drop-in alternatives, Macrovision-equipped pin-compatible parts, and practical design notes not found in the manufacturer datasheet alone.
TVP5150AM1IPBS - Ultra-Low Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5150AM1IPBS is an ultralow-power NTSC/PAL/SECAM video decoder that converts baseband analog video (composite, S-Video, or component Y/C) into 8-bit ITU-R BT.656 digital output. Housed in a 32-pin TQFP (PBS) 5x5 mm package, it integrates a high-speed 9-bit ADC, two composite or one S-Video input, and fully differential CMOS analog preprocessing channels with clamping and automatic gain control (AGC) for best signal-to-noise performance. What is a video decoder? A video decoder is a mixed-signal integrated circuit that digitizes analog broadcast video (NTSC, PAL, SECAM) and reformats it into a standard digital stream that downstream processors, image signal processors (ISPs), or video encoders can consume. In the broader taxonomy, the TVP5150AM1IPBS sits under video front-end ICs -> interface ICs -> integrated circuits, and historically it dominated mobile, surveillance, and set-top box designs where small footprint and low power were non-negotiable. Key features include a robust sync detector for non-standard and weak signals, Genlock/real-time control (RTC) output for synchronizing downstream encoders, complementary 4-line adaptive comb filtering for both luminance and chrominance paths, and a programmable chrominance trap filter. Per the TI datasheet, power consumption is typically below 150 mW, and the device operates from a 1.8 V core supply with a 3.3 V I/O supply via an integrated level shifter. Technically, the device uses a 9-bit pipelined ADC architecture, two fully differential analog preprocessing channels, and an on-chip PLL to generate the 27 MHz sampling clock from a 27 MHz crystal or external reference. The I2C interface is used for configuration of video standard, brightness, contrast, saturation, hue, and comb-filter enable, while the parallel 8-bit output uses the ITU-R BT.601 or BT.656 interface standard. Typical applications include handheld/personal video recorders, mobile phone video capture, portable media players, digital still cameras, automotive infotainment rear-seat displays, and CCTV/DVR surveillance front ends where composite CVBS must be digitized for compression ASICs or SoCs. When designing with this device, provide adequate bulk decoupling on both the 1.8 V (DVDD) and 3.3 V (IO_DVDD) rails and route the analog video inputs with controlled 75 ohm impedance to minimize reflections. The S-Video Y/C pair is preferred over CVBS for best comb-filter performance.
TVP5150AM1PBS - Ultralow-Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5150AM1PBS is an ultralow-power NTSC/PAL/SECAM analog video decoder that converts baseband composite or S-Video inputs to 8-bit ITU-R BT.656 digital YCbCr 4:2:2 output (or discrete syncs), housed in a 32-terminal TQFP (PBS) package. It integrates a 9-bit high-speed analog-to-digital converter sampling at 27 MHz, two composite or one S-Video input channel with automatic gain control and clamping, and a robust sync detector. Operating from 1.65 V to 1.95 V (digital) and 1.65 V to 1.8 V (analog), it accepts NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc), and SECAM (B, D, G, K, K1, L) video standards. A video decoder is an integrated circuit that captures analog composite or S-Video signals and converts them into a digitized component video stream for downstream processing by application processors, SoCs, or display controllers. The device category hierarchy is: video decoder -> analog front-end -> interface IC -> semiconductor. Its role in a typical embedded vision system is to bridge analog cameras or legacy analog video sources (CVBS, Y/C) to modern digital processing pipelines, eliminating the need for external ADCs and sync separators while preserving signal integrity. Key features include a high-speed 9-bit ADC, fully differential CMOS analog preprocessing with AGC and clamping for best signal-to-noise performance, complementary 4-line adaptive comb filtering on both luminance and chrominance paths, Macrovision copy-protection support, and an ultralow-power architecture suited to portable designs. A Genlock/real-time control (RTC) output is generated for synchronizing downstream video encoders in multi-camera or PIP architectures. Technically, the TVP5150AM1 uses a differential analog front end that rejects common-mode noise and supports extended temperature operation from 0°C to 70°C in the PBS package variant. Its register-based I²C control interface exposes luminance, chrominance, hue, brightness, contrast, and sharpness adjustments to the host processor. Typical applications include portable media players, set-top boxes, digital video recorders, video capture cards, automotive infotainment rear-seat entertainment, IP cameras with analog CVBS input, and surveillance DVRs. The wide standard coverage and ultralow-power operation make it suitable for any embedded design that must decode legacy analog video. When designing with this part, pay attention to the I/O supply sequencing constraint: IO_DVDD must track the 1.8 V digital supply and must not be back-powered; an external power-on-reset (POR) or supply sequencing network may be required for multi-supply rails. Place the 27 MHz crystal or clock source within 5 mm of the XTAL pin and use a star-ground topology for the CVBS traces. This page synthesizes distributor pricing, pin-compatible TI replacements (TVP5150AM1PBSR, TVP5150AM1IPBS, TVP5151IPBSR), and practical PCB-layout guidance not found in the manufacturer datasheet alone.
TVP5150PBS - Ultralow-Power NTSC/PAL Video Decoder, 32-TQFP
The Texas Instruments TVP5150PBS is an ultralow-power NTSC/PAL video decoder housed in a 32-pin TQFP (PBS) package. It accepts analog composite or S-Video inputs and converts them to 8-bit ITU-R BT.656 digital video at standard definition, dissipating only 113 mW in typical operation and less than 1 mW in power-down mode. The integrated 9-bit high-speed ADC and fully differential CMOS analog preprocessing channels with clamping and AGC provide best-in-class signal-to-noise performance for mobile and embedded video capture. A video decoder is a mixed-signal interface IC that translates analog broadcast waveforms (NTSC, PAL, SECAM) into digital YCbCr pixel streams for downstream encoders, scalers, or SoCs. Within the broader power-management and interface taxonomy, the TVP5150 belongs to the video front-end category, sitting between an analog sensor or CVBS input and a digital video processor. Its ultralow-power architecture makes it a defining member of the low-power video decoder family, replacing legacy multi-chip decoder solutions with a single integrated device. Key features include support for NTSC (M, N, 4.43) and PAL (B, D, G, H, I, M, N) standards with ITU-R BT.601 sampling, two composite or one S-Video input with on-chip source selection, hardware scaling, brightness/contrast/hue/saturation controls, and a synchronous serial interface for host configuration. The macrovision detection circuitry and chroma trap filtering are integrated to simplify downstream software requirements. The TVP5150 uses a 27 MHz reference clock and produces ITU-R BT.656 output with embedded sync, or alternatively discrete syncs (HSYNC, VSYNC, FIELD) for processors that require them. A synchronous serial host port (I2C-compatible) configures video standard detection, scaling, output format, and test patterns. Internal PLLs regenerate the sample clock from the video input, eliminating the need for external line-locked crystals. Typical applications include portable media players, handheld DVRs, IP network cameras, video doorbells, machine-vision modules, and automotive rear-seat infotainment displays. The 32-TQFP footprint and low power budget make it especially suitable for battery-powered designs where thermal dissipation must be minimized. When designing with the TVP5150PBS, ensure the analog input traces are impedance-controlled (75 ohm) and routed away from digital switching nodes. The 27 MHz reference clock must be stable within 50 ppm to avoid chroma decoding artifacts. Decouple AVDD and DVDD separately with 0.1 uF and 10 uF ceramic capacitors placed within 5 mm of the supply pins. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes that extend beyond the manufacturer datasheet, providing a single reference for engineers selecting or replacing the TVP5150PBS.
TVP5151IPBSR - Ultralow-Power NTSC/PAL/SECAM Video Decoder | TI
The Texas Instruments TVP5151IPBSR is an ultralow-power NTSC/PAL/SECAM video decoder housed in a 32-pin TQFP (PBS) package measuring 5x5 mm. It accepts composite (CVBS) and S-Video analog inputs and converts them to 8-bit ITU-R BT.656 digital video with embedded syncs, or to 8-bit 4:2:2 with discrete syncs. The decoder supports NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc), and SECAM (B, D, G, K, K1, L) standards with automatic standards detection and Macrovision copy-protection detection. A video decoder is a mixed-signal integrated circuit that digitizes analog baseband video from cameras, set-top boxes, or playback devices so a digital processor, image signal processor, or display controller can consume the stream. Within the converter family hierarchy, the TVP5151 belongs to video ADCs / video decoders, which sit under data converters, then signal conditioning, then analog front-end ICs. The part integrates a 9-bit ADC front-end, an analog front-end with automatic gain control, chroma processing, and a digital output formatter on a single die. Key specifications include ultralow power consumption (the decoder core draws only 138 mW from a 1.7 V analog and 1.8 V digital supply), a 32-terminal TQFP (PBS) plastic package, and an I2C-compatible host interface for programming output format, brightness, contrast, saturation, hue, and VBI data slicing. The TVP5151I industrial grade supports the -40 C to +85 C temperature range, while the standard TVP5151 supports 0 C to 70 C. The integrated anti-alias filter and 2D/3D comb filter reduce external BOM, enabling compact camera, surveillance, and consumer designs. Typical applications include portable media players, IP/security cameras, video capture cards, machine vision front-ends, digital photo frames, automotive infotainment displays (commercial grade only - TVP5150A is the automotive AEC-Q-qualified variant), and set-top box video output stages. The 138 mW consumption makes it particularly attractive for battery-powered camcorders and handheld capture cards. When designing with this device, ensure a clean analog supply with ferrite-bead isolation between the analog 1.8 V rail and digital 1.8 V rail. Provide a stable 14.31818 MHz VCO reference for the decoder's internal timing recovery. Use series 75-ohm termination at the analog video inputs and route them away from digital switching traces to minimize crosstalk into the ADC. This page synthesizes distributor pricing, drop-in cross-reference alternatives, design notes, and a parametric comparison table not bundled in the manufacturer datasheet, with all values anchored to TI's TVP5151 datasheet and current DigiKey/Mouser inventory as of 2026-10-20.
TVP5154AIPNP - 4-Ch Video Decoder 128-HTQFP | Texas Instruments
The Texas Instruments TVP5154AIPNP is a 4-channel, low-power NTSC/PAL/SECAM video decoder with independent scalers, housed in a 128-pin HTQFP (PNP) PowerPAD package measuring 14x14 mm. Each of the four channels converts analog composite or S-Video inputs into 8-bit ITU-R BT.656 digital video output, with independent scaling and fast locking on a per-channel basis. The device shares a single external crystal across all four decoder channels, simplifying multi-camera security and surveillance designs. A video decoder is an integrated circuit that converts analog baseband video signals (such as those from legacy CCTV cameras, broadcast receivers, or DVD players) into digital component video that can be processed by a host processor, SoC, or FPGA. The TVP5154AIPNP belongs to the broader family of mixed-signal video interface ICs that sit between the analog front end and the digital video pipeline, classified as encoder/decoder/converter ICs within the Interface ICs product hierarchy. Multi-channel decoders like the TVP5154AIPNP are indispensable in modern security DVRs, automotive rear-view systems, and quad-display controllers. Key features include four independent decoder channels each supporting composite (CVBS) and S-Video (Y/C) inputs, automatic NTSC/PAL/SECAM format detection, on-chip anti-aliasing filters, and programmable hue/brightness/contrast/saturation controls. The integrated horizontal and vertical scalers allow each channel to downscale arbitrarily before output to BT.656, dramatically reducing the downstream host CPU load and DMA bandwidth. Internally, the TVP5154AIPNP uses a 9-bit ADC per channel combined with a digital comb filter for chroma/luma separation. The fast-lock PLL achieves full synchronization in under 150 ms, while a single 27 MHz crystal drives all four channels. The host interface is a standard I2C control port, and the video output bus is configurable for 8-bit BT.656 or discrete syncs. Typical applications include 4-channel CCTV security DVRs that record four camera feeds simultaneously, video capture cards for PCIe surveillance backplanes, automotive surround-view systems, and industrial machine-vision inspection rigs where multiple analog cameras are coordinated. Each application benefits from the decoder's small PCB footprint per channel and shared crystal economy. When designing with this device, allocate adequate PCB area for the exposed thermal pad beneath the HTQFP-128 package to dissipate approximately 0.6 W of total power across all four active channels. Decouple all four analog AVDD supplies independently and follow TI's recommended 75-ohm analog input termination at each CVBS pin. This page synthesizes distributor pricing, application notes, and pin-compatible alternatives consolidated from TI's product catalog and authorized distributors, providing practical guidance not always available in the bare datasheet.
TVP5154AIPNPR - 4-Ch PAL/NTSC/SECAM Video Decoder | TI
The Texas Instruments TVP5154AIPNPR is a 4-channel, low-power NTSC/PAL/SECAM video decoder with independent scalers and fast lock, housed in a 128-pin HTQFP (PNP) PowerPAD package measuring 14x14 mm. Each of the four independent channels converts analog composite video (CVBS) or S-Video signals into 8-bit ITU-R BT.656 digital output, with discrete syncs also available. The device operates from a 1.8 V core supply and a 3.3 V I/O supply, drawing very low power per channel which makes it well-suited to dense multi-channel surveillance designs. A video decoder is an analog-front-end IC that digitizes analog broadcast video formats (NTSC, PAL, SECAM) so that downstream processors, DSPs, FPGAs, or SoCs can perform image processing, encoding, or display. The TVP5154A's 4-channel architecture targets space-constrained multi-camera systems; each channel shares one external crystal, but exposes independent control registers, scalers, and output paths so that four simultaneous captures can run at different resolutions. Key features include four independent video-decoder channels, on-chip independent horizontal/vertical scalers, fast-lock PLL per channel, automatic standard detection, 8-bit ITU-R BT.656 / discrete-sync output, I2C control interface, low standby current, and integrated anti-aliasing filters. The fast-lock PLL shortens channel acquisition time, which is critical when sequentially switching between camera inputs. Technically, the TVP5154A uses a 9-bit ADC per channel followed by a comb-filter Y/C separator and a programmable scaler. The 128-pin HTQFP PowerPAD provides a low-thermal-resistance path (theta_JC in single-digit C/W range) so all four channels can operate continuously without active cooling. The device is qualified to the industrial temperature range (-40C to +85C). Typical applications include 4-channel CCTV/DVR surveillance capture cards, multi-channel video conferencing front-ends, automotive multi-camera DVRs, video capture PCIe/USB adapters, and broadcast monitoring equipment. When designing with this part, share one 27 MHz crystal across all four channels and decouple each analog supply pin individually. Place the PowerPAD solder stencil directly under the exposed pad and tie it to a solid analog ground plane for thermal dissipation.
TVP5158IPNPR - 4Ch NTSC/PAL Video Decoder, 128-HTQFP | Texas Instruments
The Texas Instruments TVP5158IPNPR is a four-channel high-quality NTSC/PAL video decoder that digitizes and decodes all popular base-band analog video formats into digital video output. Each of the four channels integrates a 10-bit 27-MSPS analog-to-digital converter (ADC) preceded by an analog input conditioning circuit that clamps the input to a reference and applies anti-alias filtering. The device is offered in a 128-pin HTQFP (PNP) package measuring 14x14 mm with an exposed thermal pad, targeting multi-channel security and machine-vision applications. A video decoder is a mixed-signal integrated circuit that converts analog composite video signals (such as those from CCTV cameras or legacy broadcast outputs) into a digital component video stream for downstream processing by a host processor, SoC, or DSP. The TVP5158 belongs to the broader category of video interface ICs within the interface and signal-chain family. It supports NTSC (J, M, 4.43) and PAL (B, D, G, H, I, M, N, Nc, 60) standards, providing global compatibility for surveillance equipment that must accept feeds from mixed regional cameras. Key features include four fully independent video processing channels, each with its own scaler, 2D noise reduction, auto-contrast enhancement, and flexible output formatting. Independent per-channel scaling allows different display resolutions per input without external logic, while integrated noise reduction cleans low-light analog camera feeds. An I²C control interface manages all programming. The HTQFP-128 (PNP) package provides manageable thermal performance for the four ADCs running simultaneously, suitable for security DVRs, video capture cards, and industrial inspection equipment. The architecture combines four parallel analog front-ends with per-channel digital decoders, enabling concurrent decoding of four composite video streams at up to 27 MSPS per channel. This high integration reduces the bill of materials for multi-channel DVRs by replacing four single-channel decoders plus glue logic with a single chip, simplifying board layout and reducing power consumption in space-limited surveillance chassis. Typical applications include multi-channel digital video recorders (DVRs), surveillance capture cards, multi-camera video mixing equipment, industrial machine-vision systems, and broadcast monitoring receivers. Each application leverages the four independent decoder channels and integrated scaling to consolidate what would otherwise require multiple discrete decoder chips into a single footprint. Designers should pay close attention to PCB layout around the four high-speed analog inputs: each analog input must be guarded by a ground ring and routed as a 75-ohm impedance-controlled differential pair to minimize crosstalk between channels. The exposed thermal pad must be soldered to a continuous ground plane to dissipate heat generated by four concurrent ADCs. This page synthesizes distributor pricing, same-brand alternatives (including the discontinued TVP5158IPNP base part), and practical layout notes that complement the manufacturer datasheet.
TVP5160PNP - NTSC/PAL/SECAM 10-Bit Video Decoder HTQFP-128 | TI
The Texas Instruments TVP5160PNP is a high-quality digital video decoder that digitizes and decodes all popular baseband analog video formats into digital component video, integrating two 11-bit 60-MSPS analog-to-digital converters with analog preprocessors, fixed RGB-to-YUV color space conversion, and Macrovision detection. Housed in a 128-pin HTQFP (PNP) package measuring 14x14 mm, the device supports NTSC (J, M, 4.43), PAL (B, D, G, H, I, M, N, Nc, 60) and SECAM (B, D, G, K, K1, L) composite and S-Video inputs as well as component YPbPr and RGB (SCART) signals. A video decoder is an analog front-end IC that converts legacy analog video waveforms - originally designed for CRT displays - into digital YCbCr component streams for downstream processing by display controllers, scalar ASICs, video processors, or application processors. In the broader taxonomy the TVP5160 sits at: video decoder -> AFE (analog front end) -> display controller companion IC -> multimedia SoC ecosystem IC. Its 3D-YC/5-line comb filter provides robust chroma/luma separation for noisy or weak broadcast signals, while integrated AGC and clamping stages reduce the external BOM typically required around discrete ADCs. Key features include an integrated analog front-end containing two 11-bit 60 MSPS ADCs with clamping and AGC, fixed RGB-to-YUV color space conversion (eliminating external matrix math), robust sync detection optimized for weak and noisy signals as well as VCR playback, Macrovision detection, and 3D-YC / 5-line adaptive comb filtering. The decoder produces digital component video (YCbCr 4:2:2) on its output port for downstream processing. Operating voltage spans 3.0V to 3.6V (3.3V typical) with typical power dissipation of 904 mW. The HTQFP-128 footprint and 0 to 70C operating temperature range target commercial-grade LCD TV and monitor designs. Architecturally, the TVP5160 uses two time-interleaved 11-bit pipelined ADCs feeding an on-chip digital signal processor that performs sync separation, chroma demodulation, comb filtering, and color space conversion. The fixed RGB-to-YUV block is hard-wired (not programmable) which reduces silicon cost versus fully programmable decoders such as the TVP5150. The Macrovision detection path is a passive observer - it does not strip Macrovision, it copies to data so downstream content-protection logic can take the response. Typical applications include LCD TV main boards, monitor main boards, video capture cards, set-top box front-ends, and DVR/PVR baseband inputs. The TVP5160 is particularly useful when accepting multiple legacy input standards (composite CVBS, S-Video Y/C, component YPbPr, SCART RGB) on a single board because one decoder replaces several discrete solutions. The Macrovision detection path also enables DRM-aware DVR designs. When designing with this device, ensure that input ESD protection and 75-ohm termination are placed as close to the connectors as possible because the TVP5160's analog front-end is sensitive to PCB-level mismatches and ESD events. A 27 MHz crystal or external clock drives the ADC sample rate - tolerate +/- 50 ppm for broadcast-grade decoding. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet, enabling a faster engineering decision for LCD TV and monitor main-board designs.
TXB0104-Q1 - 4-Bit Auto-Direction Level Translator | TI
The Texas Instruments TXB0104-Q1 is an automotive-grade 4-bit bidirectional voltage-level translator with automatic direction sensing and +/-15 kV ESD protection, available in a 14-pin TSSOP (PW) package. It translates between two independent supply rails: the A port tracks VCCA from 1.2 V to 3.6 V, while the B port tracks VCCB from 1.65 V to 5.5 V, enabling any-to-any translation between 1.2 V, 1.8 V, 2.5 V, 3.3 V and 5 V logic domains. A voltage-level translator is a logic-family device that allows integrated circuits operating at different supply voltages on the same PCB to exchange digital signals safely. Within the power-and-signal-management hierarchy, it sits alongside buffers and bus switches as a fundamental interface IC, preventing overvoltage damage and ensuring valid logic thresholds between low-voltage MCUs, FPGAs, and 5 V peripherals. Key features include auto-direction sensing, which eliminates the DIR control pins required by '245-style translators, a data rate of up to 100 Mbps, and VCC isolation: when either supply is at GND, all I/O enters Hi-Z. The AEC-Q100-qualified TXB0104-Q1 also carries +/-15 kV HBM ESD protection, exceeding the standard JESD ratings cited in the TI datasheet family. Architecturally, the TXB0104 uses a self-directed, edge-rate-driven one-shot scheme that detects the direction of each transition and briefly strengthens the opposite driver, allowing it to drive 4 channels in either direction without software intervention. The OE pin three-states all outputs for power sequencing and bus isolation. Typical applications include SPI and UART level conversion between 3.3 V MCUs and 5 V peripherals, GPIO expansion in automotive body and infotainment modules, and mixed-voltage FPGA I/O. Note that the push-pull architecture is not recommended for open-drain buses such as I2C or 1-Wire; use the TXS0104E-Q1 for those. Design consideration: keep unloaded outputs low-impedance driven or grounded, since the auto-direction circuitry can oscillate on lightly loaded or capacitively large nets; series resistors above 25 k-ohm are not supported. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in alternatives (NXP NTS0304E, ADI ADG3304), and practical design notes for automotive level-shifter selection.
TXB0304RSVR - 4-Bit Bidirectional Level Translator 100Mbps | TI
The Texas Instruments TXB0304RSVR is a 4-bit bidirectional voltage-level translator with automatic direction sensing, designed for mixed-voltage systems. It operates with two separate power-supply rails, VCCA and VCCB, each configurable from 0.9V to 3.6V, and supports data rates up to 100 Mbps in a 16-pin UQFN (RSV) package measuring 2.6mm x 1.8mm, ideal for space-constrained designs. A voltage-level translator is a crucial component in modern electronics, allowing communication between ICs operating at different voltage levels. For example, a 1.8V microcontroller can interface with a 3.3V sensor or memory device without risking damage or logic errors. The TXB0304 belongs to the TXB family of auto-direction-sensing translators, part of TI's broader level-shifting portfolio that includes unidirectional and bidirectional solutions for various interface standards. Key features include a fully symmetric supply range (0.9V to 3.6V on both VCCA and VCCB), automatic direction sensing that detects data flow without external direction control, and a high data rate of 100 Mbps. The device also provides an isolation function: if either VCC input is at GND, all outputs are placed in a high-impedance state, preventing backflow current and protecting the system. Technically, the TXB0304 uses a one-shot circuit to accelerate rising edges, ensuring fast signal propagation even with capacitive loads. The architecture includes a pass-gate transistor with a pull-up resistor on each I/O pin, providing robust translation. The device is specified from -40C to +85C, is RoHS compliant and lead-free. Typical applications include SPI, I2C, UART, and GPIO interfacing between microcontrollers, sensors, memory, and peripherals at different voltage levels, particularly in IoT devices, portable electronics, and industrial control systems. Design tip: ensure both VCCA and VCCB are powered and place decoupling capacitors close to the power pins. Note that push-pull drivers are preferred; open-drain buses require external pull-ups sized carefully.
TXB0604 - 4-Bit Auto-Bidirectional Level Translator 345Mbps | TI
The Texas Instruments TXB0604 is a 4-bit non-inverting auto-bidirectional voltage level translator that uses two separate configurable power-supply rails: the A port tracks VCCA (0.9V to 2V) and the B port tracks VCCB (1.65V to 3.6V), with the constraint VCCA <= VCCB. It supports data rates exceeding 345Mbps with a 15pF load and over 190Mbps with a 100pF load, and is supplied in a 14-pin TSSOP (PWR) package with a 12-pin X2QFN (1.6x1.6mm) option (RWBR). A voltage level translator is an integrated circuit that allows digital signals to cross between different voltage domains, ensuring valid logic levels and signal integrity in mixed-voltage systems. Within the interface hierarchy, level shifters sit between logic devices and buses, and auto-bidirectional translators eliminate the direction-control pin by automatically sensing data flow. Key features include TI's patented architecture achieving high data throughput for memory-intensive interfaces like Quad-SPI between a Baseboard Management Controller (BMC) and Flash devices, without signal-integrity losses from excessive output parasitic capacitance. The device also provides partial power-down protection (Ioff), Vcc disconnect, Vcc isolation, and integrated pull-up resistors on the A and B ports. Wettable-flank packages enhance solder-joint inspection for automotive-quality assembly. Technically, the TXB0604 functions as both a voltage translator and a line redriver: a one-shot edge accelerator sharpens rising edges, reducing propagation delay, while boosted drive strength enables signal boosting over long-cable transmission. Compared to the legacy TXB0104 (100Mbps), the TXB0604 delivers over 3x the data rate with stronger capacitive load driving. Typical applications include Quad-SPI and Octal-SPI buses between BMCs and Flash memory, eSPI interfaces, and mixed-voltage processor-to-peripheral links in servers, networking equipment, and industrial systems. Design tip: always ensure VCCA <= VCCB, place decoupling capacitors close to both supply pins, and avoid floating unused inputs in partial power-down states. Pricing below is as of 2026-08-30.
TXE8124-Q1 - 24-Bit Automotive SPI I/O Expander | TI
The Texas Instruments TXE8124-Q1 is an automotive-grade 24-bit SPI bus I/O expander with interrupt output, reset input, and I/O configuration registers, operating from a 1.65V to 5.5V VCC supply and available in a VQFN-32 (RHB) package. An SPI I/O expander is a type of interface IC within the broader semiconductor hierarchy (interface IC -> I/O expander -> logic/integration device) that adds general-purpose parallel input/output pins to a microcontroller or processor using the four-wire Serial Peripheral Interface protocol. It belongs to the same product family as GPIO extenders and port expanders, and is the SPI counterpart to I2C expanders such as the PCX857x family, offering higher speed and deterministic timing. Key features include 24 configurable GPIO channels with individual I/O configuration registers, a dedicated interrupt output (INT) that flags input state changes to the host controller, and a reset input (RST) for rapid recovery of the register map to a known default state. The device supports both standard point-to-point SPI communication and daisy-chaining of multiple devices, allowing several expanders to share a single SPI chip-select in dense I/O designs. Performance scales with supply voltage: according to the Texas Instruments datasheet, the TXE8124-Q1 supports a 10MHz SPI clock when VCC is 3.3V to 5.5V and 5MHz when VCC is 1.65V to 5.5V. This voltage-flexible operation allows direct interfacing with 1.8V, 2.5V, 3.3V, and 5V logic domains without level translation in many systems. Typical applications include automotive body control modules, gateway ECUs, and infotainment boards that need additional GPIO for switches, push-buttons, sensors, LEDs, fans, and relay drivers when the host processor has exhausted its native GPIO. Daisy-chaining suits seat-control modules and door zones where dozens of switches must share one SPI port. When designing with this device, plan daisy-chain timing budgets around the 10MHz maximum clock and account for the added shift-register latency per cascaded device; also verify the interrupt output is polled or serviced before the register state can change again. This page synthesizes verified distributor and manufacturer data with drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers a single citable reference.
TXE8148DGGR - 48-Bit SPI I/O Expander 10MHz | Texas Instruments
The Texas Instruments TXE8148DGGR is a 48-bit SPI bus I/O expander with interrupt output, reset input, and I/O configurable registers, delivering 48 general-purpose I/Os across six 8-bit ports with 10 MHz SPI operation from a 1.65 V to 5.5 V supply in a 56-pin TSSOP package. An I/O expander is a peripheral interface IC that increases the number of input/output pins available to a host microcontroller or processor without changing the host silicon. In the digital system hierarchy it sits between the host bus master (SPI in this case) and the GPIO load, functioning as a bridge in the broader family of interface ICs. I/O expanders such as the TXE8148 offload pin-count-constrained MCUs, allowing one SPI bus to control dozens of additional digital signals with only four host wires plus chip select. Key features include per-I/O programmable open-drain or push-pull outputs, programmable pullup and pulldown resistors, bus-hold latchable inputs, maskable interrupts with an interrupt status register, and a fail-safe operating mode. The device also supports daisy-chaining of multiple TXE8148 units on a single SPI bus, and documentation is available to aid functional safety system design. Technically, the TXE8148 maintains a 10 MHz SPI bus frequency across the entire 1.65 V to 5.5 V VCC range, which is significant for mixed-voltage designs where many expanders derate speed at low supply. The six-port, eight-I/O-per-port register map gives engineers byte-aligned access to all 48 channels, and the reset input provides deterministic recovery of all registers to a known default state after a fault or watchdog event. Typical applications include industrial control panels that need many switch inputs and relay outputs, functionally safe systems requiring documented failure modes, and server or networking backplanes where a processor must monitor dozens of card-present, fault, and status signals. Design consideration: plan your interrupt strategy early - the maskable interrupt and status register let the host poll a single register instead of 48 GPIOs, but interrupt masks must be configured after every reset since registers return to defaults. This page synthesizes distributor pricing, availability, and practical design guidance not found in the manufacturer datasheet alone.
TXG1010 - 1-Bit ±10V Ground-Level Translator | Texas Instruments
The Texas Instruments TXG1010DSER is a 1-bit, fixed-direction, non-galvanic voltage and ground-level translator supporting logic-level shifting between 1.71V and 5.5V and ground-level shifting of up to ±10V, housed in a small 8-pin SOT-23 (DSE) surface-mount package. A level translator (also called a level shifter or voltage translator) is a logic IC that enables communication between digital circuits operating at different supply voltages, for example a 1.8V microcontroller driving a 5V peripheral. Within the signal-chain hierarchy, the TXG1010 belongs to the voltage-level-translation family of interface ICs. What distinguishes the TXG1010 family from traditional level translators is its ability to shift signals not only between different logic levels but also across different ground domains, solving the challenge of voltage translation between subsystems whose grounds differ by up to ±10V. Key features include a wide 1.71V to 5.5V logic-level translation range, ±10V ground-level shifting capability, a fixed-direction architecture that removes the need for a direction-control pin, and a single-channel (1-bit) topology that minimizes board area. The non-galvanic approach means there is no isolation barrier; the device tolerates ground potential differences rather than providing reinforced isolation, which is an important distinction from digital isolators. Technically, the device translates a logic input referenced to one ground domain into an output referenced to a second ground domain, while simultaneously performing standard low-voltage logic up- or down-translation. The fixed-direction design simplifies control logic and reduces pin count, making it suitable for one-way status, enable, and control signals. Typical applications include ground-offset compensation between a controller and a motor driver, level shifting in automotive and industrial subsystems where ground lift occurs under load, and interfacing between negative-rail or high-side circuitry and a low-voltage MCU. When designing with the TXG1010, remember that it is non-galvanic: sustained ground differences must remain within the ±10V rating, and it should not be used where safety isolation is required. Refer to the manufacturer datasheet for the exact truth table and supply sequencing requirements. This page synthesizes verified distributor and manufacturer data, practical design notes, and selection guidance not found in the datasheet alone. Pricing and stock figures are as of 2026-10-19.
TXG1021-Q1 - ±10V 2-bit Ground-Level Translator | TI
The Texas Instruments TXG1021-Q1 is an automotive-qualified 2-bit, fixed-direction, non-galvanic ground-level translator supporting DC ground shifts up to ±10V and logic-level shifting between 1.71V and 5.5V, with propagation delay under 5ns and data rates above 250Mbps in an 8-pin SOIC package. A ground-level translator is a specialized voltage translator that solves a problem conventional level shifters cannot: signals referenced to grounds that sit at different DC potentials. In a classic automotive or industrial system, heavy load currents lifted through shared harness returns create millivolt-to-volt offsets between a sensor ground and a controller ground. Standard level shifters interpret those offsets as logic errors, while a non-galvanic ground-level translator tolerates the DC offset directly on its inputs while still reproducing clean logic edges at the destination domain. Key features include AEC-Q100 qualification for automotive deployments, DC shift tolerance up to ±10V, AC noise rejection of 20VPP up to 45MHz, and common-mode transient immunity (CMTI) of 1kV/us. Channel-to-channel skew is below 0.20ns and propagation delay stays under 5ns, so the device does not become a timing bottleneck even in fast digital links. Quiescent power consumption is low at approximately 0.8mA per the manufacturer datasheet. Architecturally, the TXG102x family uses a non-galvanic coupling approach rather than isolation barriers, giving it near-zero added latency compared with digital isolators while still rejecting ground potential differences. This makes it attractive for bridging control grounds in battery-managed, motor-driven, or switched-load environments where return paths are far from ideal. Typical applications include automotive body-control and gateway modules, motor inverter gate-drive signaling across shifted grounds, industrial PLC I/O with grounded sensor offsets, and battery-management communication lines where cell-stacking creates ground potential differences. Design consideration: verify that expected DC ground offset stays within the ±10V rating under all load and fault conditions, and follow the datasheet layout guidance for the ground-shifted domain. This page adds value beyond the manufacturer datasheet by synthesizing drop-in alternatives, comparison tables, and practical design notes in one place.