Microcontroladores

Productos (19.000+)

PIC18F26K83-E/SSVAO - 64KB Flash, CAN, AEC-Q100 8-bit MCU | Microchip
PIC18F26K83-E/SSVAO

PIC18F26K83-E/SSVAO - 64KB Flash, CAN, AEC-Q100 8-bit MCU | Microchip

The Microchip Technology PIC18F26K83-E/SSVAO is a 28-pin, 8-bit PIC18 microcontroller with 64 KB Flash, 4 KB RAM, and 1 KB EEPROM, integrated with CAN technology and a 12-bit ADC with Computation (ADC2). It operates up to 64 MHz, supports an extended temperature range, and is qualified to AEC-Q100 for automotive applications, all housed in an SSOP-28 package. This device belongs to the PIC18 (L)F25/26K83 family of low-power, high-performance microcontrollers. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working RAM, EEPROM, and a rich set of peripherals such as timers, ADC, communication controllers, and I/O into one package. The K83 sub-family adds CAN, ADC2 with Capacitive Voltage Divider (CVD) for touch sensing, vector interrupts, DMA, and comparators, placing it in the mid-range of Microchip's enhanced PIC18 portfolio, suitable for industrial and automotive designs requiring deterministic real-time response. Key features include 64 KB self-programmable Flash, 4 KB SRAM, 1 KB EEPROM, a 12-bit ADC2 with up to 24 channels, three op-amps configurable as comparators, multiple communication peripherals including CAN FD, SPI, I2C, UART with LIN, and DMA for offloading core data movement. The core executes most instructions in one cycle at 64 MHz, delivering up to 16 MIPS, while the integrated nanoWatt XLP power management minimizes active and sleep currents for battery-aware designs. Architecturally, the device couples a Harvard RISC core with a wide peripheral set and Direct Memory Access (DMA), allowing deterministic data flow between ADC, communication modules, and memory without CPU intervention. ADC2 adds hardware averaging, oversampling, filtering, and threshold comparisons, enabling capacitive touch and precision sensor measurements while freeing the CPU for application logic. Typical applications include automotive body and comfort modules (lighting, seat, HVAC, mirror control), industrial CAN nodes (sensor hubs, motor control companions, isolated gateways), touch-sensing user interfaces using CVD, and home appliances requiring AEC-Q100 grade reliability and a CAN bus interface. When designing with this part, ensure the SSOP-28 land pattern is used and that unused pins are tied to defined logic levels per Microchip guidance. Verify CAN bus termination (typically 120 ohm at each end of the trunk) and place decoupling capacitors close to VDD/VSS pairs to support the ADC2 and CAN transceiver cleanly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18F26K83-I/ML - 8-Bit 64MHz 64KB Flash MCU w/ CAN | Microchip
PIC18F26K83-I/ML

PIC18F26K83-I/ML - 8-Bit 64MHz 64KB Flash MCU w/ CAN | Microchip

The Microchip Technology PIC18F26K83-I/ML is a 64 MHz 8-bit PIC18 XLP microcontroller with 64 KB Flash, 4 KB RAM, and integrated CAN, offered in a 28-pin QFN (6x6 mm) package with an exposed thermal pad. It operates across 2.3V-5.5V with XLP (eXtreme Low Power) technology, integrates a 12-bit ADC with Computation (ADC2) supporting Capacitive Voltage Divider (CVD) touch sensing, and provides Functional Safety (FuSa) features for safety-critical designs. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM), and programmable peripherals that engineers configure to read sensors, drive actuators, and exchange data via serial busses. PIC18 MCUs use a modified Harvard architecture optimized for deterministic real-time control, and the K-series extends that line with enhanced peripherals like ADC2, DMA, and CIP (Core Independent Peripherals). Within Microchip's 8-bit portfolio, the PIC18F26K83 sits in the K83 sub-family that combines an MSSP-based CAN module, 12-bit differential ADC, and XLP battery-friendly sleep currents below 100 nA. Key features of the PIC18F26K83-I/ML include 64 KB self-programmable Flash (32K x 16 words), 4 KB SRAM, 1 KB EEPROM, four 16-bit timers, two I2C, two SPI, four UART, and a CAN 2.0B module. ADC2 automates oversampling, averaging, and threshold comparison without CPU intervention, freeing cycles for higher-level control loops. The device also includes a Peripheral Pin Select (PPS) engine that remaps most digital peripherals to any I/O pin, simplifying PCB routing on dense boards. Designed for industrial-grade reliability, the PIC18F26K83-I/ML supports -40C to +85C operation, watch timers, windowed WDT, and CRC/SCAN memory integrity checking. The 28-QFN exposed pad provides a low theta_JA footprint suitable for compact industrial modules and energy-meter PCBs that previously required larger SSOP packages. Internal DMA moves data between peripherals and RAM without CPU load, enabling efficient noise-filter pipelines and high-speed UART/CAN traffic. Typical applications include industrial CAN node controls (sensor hubs, motor pre-drivers, building automation), touch-sensing human-machine interfaces using CVD, automotive body and accessory ECUs, e-metering, and battery-powered IoT sensor nodes. Designers benefit from MPLAB X IDE, MCC pin/clock code generators, and the PIC18F26K83 Plug-In Module (MA180037) for rapid prototyping on Microchip development boards. When selecting this part, consider that the 28-QFN variant (-I/ML, industrial -40 to +85C) is drop-in compatible with the 28-SSOP (-I/SS) and 28-SOIC (-I/SO) variants, but PCB re-layout is required to migrate between QFN and leaded packages. Designers migrating from the older PIC18F25K80 gain ADC resolution (12-bit vs 10-bit), CAN-FD capability, DMA, and CIP peripherals with software-level compatibility through the XC8 toolchain. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's K80/K42 families, design notes covering ADC2 configuration and CAN bus termination, and an AEO-optimized FAQ tailored to engineers evaluating this MCU for new designs or replacement of legacy K80 silicon.

Cotización Contacto
PIC18F26K83-I/MX - 64KB Flash 8-bit MCU with CAN, 28-UQFN | Microchip
PIC18F26K83-I/MX

PIC18F26K83-I/MX - 64KB Flash 8-bit MCU with CAN, 28-UQFN | Microchip

The Microchip PIC18F26K83-I/MX is a low-power, high-performance 8-bit PIC microcontroller running up to 64 MHz with 64 KB of Flash, 4 KB of SRAM, and integrated CAN, in a 28-pin UQFN (6x6 mm) package. It belongs to the PIC18(L)F25/26K83 family with Functional Safety (FuSa) and XLP extreme low-power technology. An 8-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU core, non-volatile program memory (Flash), working RAM, and a rich set of peripherals (ADC, timers, communication ports) onto a single die. MCUs are the basic building block of every embedded system - from simple sensor nodes to industrial controllers. The PIC18 family sits in Microchip's mainstream 8-bit portfolio, positioned above baseline PIC10/12/16 parts by offering higher MIPS, more memory, CIPs (Core Independent Peripherals), and richer communication peripherals. Key features of the PIC18F26K83 include a 12-bit ADC with Computation (ADC²) supporting Capacitive Voltage Divider (CVD) for advanced touch sensing, averaging, filtering, and oversampling; a 5-bit DAC; multiple Core Independent Peripherals such as CWG, CCP, PWM, and NCO; and an integrated CAN module for automotive and industrial networking. The device supports up to 64 MHz operation from a 2.3V-5.5V supply, with XLP technology providing sub-microamp sleep currents for battery-powered applications. Architecturally, the part uses an enhanced mid-range PIC18 CPU with a hardware multiplier, indexed addressing, and a 31-level stack, allowing efficient C compilation through the MPLAB XC8 toolchain. The 28-UQFN package is the smallest footprint option in this family, with a 6x6 mm body and 0.6 mm pitch, suiting space-constrained designs that still need full peripheral integration. Typical applications include automotive body and comfort modules, industrial sensor nodes with CAN bus, low-power IoT edge devices, capacitive touch human-machine interfaces, and functional-safety systems where the FuSa documentation aids certification. The CAN bus and 12-bit ADC² make it especially strong in distributed sensor networks where deterministic low-latency conversion and reliable communication matter. When designing in this part, plan your I/O assignments carefully against the 28-pin budget: many peripherals are multiplexed onto shared pins, and CAN, the ADC, and PWM share I/O. Always consult the device pinout table before locking in the PCB layout, and provide adequate decoupling on VDD/VSS pairs near each pin cluster. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone - giving procurement and embedded engineers a faster path to a working BOM.

Cotización Contacto
PIC18F26K83-I/SP - 8-bit 64MHz 64KB Flash MCU w/ CAN | Microchip
PIC18F26K83-I/SP

PIC18F26K83-I/SP - 8-bit 64MHz 64KB Flash MCU w/ CAN | Microchip

The Microchip Technology PIC18F26K83-I/SP is a full-featured 8-bit PIC18 XLP microcontroller integrating a 64 MHz CPU core, 64 KB of Flash program memory, 4 KB of SRAM, and a hardware CAN 2.0B controller, all in a 28-pin SPDIP (SP) through-hole package. It is part of the PIC18(L)F25/26K83 family targeted at functional-safety (FuSa), industrial, and automotive applications where deterministic CAN communication and low-power XLP operation are required. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program and data memory, plus configurable peripherals on one silicon die. The PIC18F26K83 belongs to the broader taxonomy of 8-bit microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. The 'K83' silicon combines legacy PIC18 peripherals with newer-generation IP such as a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) touch sensing, averaging, filtering and oversampling, allowing advanced touch and sensor interfaces without software state machines. Key features include the 12-bit ADC2 with up to 24 channels, four 8-bit timers plus four 16-bit timers, four 10-bit PWM modules, two USART, two SPI, two I2C, and one CAN 2.0B controller. The XLP nanoWatt XLP technology provides deep-sleep currents down to the sub-microamp range, while the integrated peripheral pin-select (PPS) remaps most digital peripherals to any I/O pin, dramatically simplifying PCB routing. Hardware DMA and vectored interrupts further offload the CPU in deterministic CAN-message handling and motor-control loops. Typical applications include CAN nodes in automotive body and chassis ECUs, industrial sensor and motor-control modules, capacitive touch user interfaces, building-automation controllers, and battery-powered IoT edge devices that require functional safety. The wide 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V rails commonly found in industrial CAN networks. When designing in this part, confirm the extended (-40 C to +125 C) 'I' temperature grade matches your environment, allocate the 28-SPDIP footprint with a socket-friendly pitch for through-hole rework, and reserve the ICD3/ICD4 pins for in-circuit debugging during firmware bring-up. Always validate the CAN bus termination and dominant-bit timing using Microchip's MPLAB X IDE and the CAN peripheral library before production release. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC18F K-series, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F26K83-I/SS - 8-bit 64MHz 64KB Flash MCU | Microchip | CAN+ADC2
PIC18F26K83-I/SS

PIC18F26K83-I/SS - 8-bit 64MHz 64KB Flash MCU | Microchip | CAN+ADC2

The Microchip Technology PIC18F26K83-I/SS is an 8-bit PIC18 XLP microcontroller with CAN bus and 64KB Flash, packaged in a 28-pin SSOP. It operates at up to 64MHz, integrates a 12-bit ADC with Computation (ADC2), and offers 25 I/O pins in an industrial -40C to +85C temperature range. A microcontroller (MCU) is an integrated circuit that combines a CPU core, volatile memory (RAM), non-volatile program memory (Flash/ROM), and configurable peripherals on a single die. Within the broader taxonomy, the PIC18F26K83 sits in the 8-bit PIC18 family -> PIC microcontrollers -> microcontrollers (MCU) -> microcontrollers and processors -> embedded semiconductors. Its XLP (eXtreme Low Power) pedigree targets battery-powered and always-on designs where nanoWatt sleep currents and fast wake-up times are critical. Key features include 64KB (32K x 16 words) Flash program memory, 4KB RAM, 1KB EEPROM, a 64MHz internal oscillator, and a 12-bit ADC2 with Capacitive Voltage Divider (CVD) hardware automation for advanced touch sensing, oversampling, averaging and filtering. Communication peripherals include CAN, I2C, SPI, UART/USART and LINbus, supported by DMA, vector interrupts, a 16-bit PWM module, and a windowed watchdog timer. Functional Safety (FuSa) features suit IEC 60730 class B-capable appliance designs. Architecturally the PIC18F26K83 uses Microchip's enhanced Harvard RISC core with a 16-bit instruction word and an 8-bit data path, augmented by a hardware multiplier and a 32-level stack. The ADC2 peripheral offloads sensor post-processing via dedicated hardware, reducing CPU wake events and enabling lower system power. Typical applications include CAN-connected industrial sensors, automotive body and comfort modules, capacitive touch user interfaces, appliance control boards, building automation nodes, and LIN/CAN gateways. Its combination of CAN, ADC2 and XLP makes it a strong fit for space-constrained, networked, low-power embedded systems. When designing with this device, place a 100 nF decoupling capacitor on VDD within 3 mm of the pin and a bulk 10 uF near the IC, route the 28-pin SSOP thermal pad and unused I/O per Microchip's guidelines, and reserve ICSP programming pins (PGC/PGD) with test-point access for production. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F26K83T-I/MX - 64KB Flash, CAN, 8-bit MCU | Microchip
PIC18F26K83T-I/MX

PIC18F26K83T-I/MX - 64KB Flash, CAN, 8-bit MCU | Microchip

The Microchip PIC18F26K83T-I/MX is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 4KB RAM, integrated CAN 2.0B, and a 12-bit ADC with Computation (ADC²) for advanced touch sensing and signal conditioning, packaged in a 28-UQFN (6x6 mm). It operates up to 64MHz across 2.3V–5.5V with eXtreme Low Power (XLP) sleep currents under 1 µA, and is part of the Functional Safety (FuSa) family. An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that combines a RISC instruction set, on-chip Flash program memory, SRAM data memory, and a rich set of peripherals (timers, ADC, PWM, communication modules) into a single die. Within the broader taxonomy, the PIC18F26K83 sits below the PIC18 family → 8-bit MCU → microcontroller → embedded controller → semiconductor, and is positioned for low-power mixed-signal applications where CAN connectivity and analog integration are required. Key differentiating features include ADC² (12-bit, with Capacitive Voltage Divider, averaging, filtering, and automatic threshold comparison), up to four dedicated PWM channels with edge-aligned and center-aligned modes, a Configurable Logic Cell (CLC), three 16-bit timers, four CCP modules, two UART, two SPI, and an I²C module. The integrated CAN 2.0B controller with filtering supports robust industrial and automotive networked nodes. The PIC18F26K83 implements a 16-bit instruction word with a modified Harvard bus, dual 16-level hardware stack, and a peripheral pin select (PPS) scheme that lets designers remap digital peripherals onto a wide range of I/O pins, simplifying PCB layout. The on-chip 32kHz oscillator and PLL enable low-jitter operation while preserving XLP sleep performance. Typical applications include industrial sensor nodes with CAN, HVAC controls, building automation, low-power IoT sensor hubs, capacitive touch user interfaces, and small motor-control stages where the integrated PWM and ADC simplify the BOM. When designing with this device, take advantage of the ADC² CVD hardware for cap-touch buttons and sliders to eliminate external touch ICs, and use the PPS system to place peripheral signals on convenient pins without board rework. This page synthesizes Microchip datasheet specifications, current distributor pricing, pin-compatible alternatives, and practical design notes that go beyond the catalog summary.

Cotización Contacto
PIC18F26K83T-I/SO - 8-Bit 64MHz MCU, 64KB Flash, 28-SOIC | Microchip
PIC18F26K83T-I/SO

PIC18F26K83T-I/SO - 8-Bit 64MHz MCU, 64KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC18F26K83T-I/SO is an 8-bit PIC microcontroller from the PIC® XLP™ 18K family with Functional Safety (FuSa) capability, running at 64 MHz with 64 KB of Flash program memory, 4 KB of SRAM, and 1 KB of EEPROM, all housed in a 28-pin SOIC package. It integrates a 12-bit ADC with Computation (ADC²) for automated Capacitive Voltage Divider (CVD) touch sensing, a 5-bit DAC, multiple communication peripherals, and an integrated CAN module. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that processes data in 8-bit wide paths and integrates CPU core, non-volatile Flash program memory, volatile SRAM data memory, peripherals, and I/O on one die. 8-bit MCUs sit within the broader category of microcontrollers -> embedded processors -> semiconductor ICs. They remain dominant in cost-sensitive and low-power applications because of mature toolchains, predictable real-time behavior, and very low standby current draw, all of which make them the workhorse of the embedded industry. Key features of the PIC18F26K83 include XLP (eXtreme Low Power) technology for sub-µA sleep currents, a 12-bit ADC with computation engine for averaging and oversampling, hardware CAN 2.0B, four 16-bit timers, two I²C, two SPI, two UART, a 5-bit DAC, and CTMU for capacitive touch. The 28-SOIC variant (the SO package) gives 25 user I/O pins, sufficient for sensor nodes and human-interface designs. Architecturally, the part uses a modified Harvard architecture with a 16-bit instruction word and 8-bit data path, a 31-level hardware stack, and a priority-level interrupt controller. ADC² offloads averaging, oversampling, filtering, and threshold detection from the CPU, freeing MIPS for application logic and reducing firmware complexity for touch and sensor signal chains. Typical applications include automotive body and sensor nodes (via CAN), industrial control and sensor hubs, capacitive touch human interfaces, low-power IoT edge nodes, and functional-safety designs that require IEC 61508 SIL capable documentation. The wide 2.3 V to 5.5 V operating range and robust peripherals support battery-powered systems as well as 5 V industrial buses. Design tip: reserve a stable, low-impedance ground plane under the MCU and keep analog traces short when routing the 12-bit ADC inputs to preserve signal integrity. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.

Cotización Contacto
PIC18F26Q10-E/ML - 8-Bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/ML

PIC18F26Q10-E/ML - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/ML is an 8-bit PIC18 XLP microcontroller delivering 64 MHz CPU performance with 64 KB Flash, 4 KB SRAM, and 256 B EEPROM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It operates from 2.5 V to 5.5 V with 5 V tolerance on digital I/O, integrates a 10-bit ADC with Computation (ADC2), a 5-bit DAC, four 10-bit PWM outputs, configurable logic cells (CLC), complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and scan/CRC for functional-safety applications. An 8-bit microcontroller (MCU) is a single-chip computer optimized for embedded control, executing one byte per instruction cycle while integrating CPU, non-volatile program memory, RAM, and peripherals on one die. Within the semiconductor hierarchy, the PIC18F26Q10-E/ML is a microcontroller belonging to the 8-bit MCU class, a sub-category of microcontrollers, which themselves sit under embedded processors, broader mixed-signal ICs, and finally the semiconductor taxonomy. Its 8-bit RISC core, modified Harvard architecture, and 5 V I/O tolerance make it distinct from 3.3 V ARM Cortex-M parts. Key features include Functional Safety (FuSa) support, ultra-low-power XLP sleep currents, 36 instruction set, hardware multiplier, direct and indirect addressing modes, multiple I/O ports (PORTA/PORTB/PORTC), and on-board debug via ICD/ICSP. The 64 KB Flash supports 100K endurance cycles typical, with self-programmability and code protection. The 28-QFN (6x6) package provides 23 I/O pins and a low thermal resistance path through the exposed pad for high-current GPIO drive. The PIC18-Q10 architecture pairs a deterministic 8-bit core with Core Independent Peripherals (CIPs) - CLC, CWG, HLT, and ADC2 - which offload timing-critical tasks from the CPU, improving real-time responsiveness. The 5 V operation directly interfaces to industrial sensors, motor drivers, and noisy environments without external level shifters, reducing BOM and PCB area. Typical applications include industrial sensor nodes, BLDC/PMSM motor control, LED lighting controllers, home appliances, automotive body and chassis ECUs (non-safety), IoT edge nodes with long battery life, and human-machine interfaces. The XLP nanoWatt technology enables sleep currents below 50 nA typical, suiting battery-backed designs. When designing with this device, allocate the exposed pad (EP) as the primary thermal dissipation path, place a 100 nF decoupling capacitor on each VDD pin, and reserve the ICSP/ICD pins for in-circuit programming to simplify firmware iteration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - enabling faster vendor comparison and supply-chain decisions.

Cotización Contacto
PIC18F26Q10-E/SO - 8-Bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/SO

PIC18F26Q10-E/SO - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/SO is a 28-pin 8-bit microcontroller from the PIC18-Q10 family, operating at up to 64 MHz with 64 KB of Flash program memory in a 28-SOIC package. This XLP (eXtreme Low Power) device integrates intelligent analog peripherals, configurable logic cells (CLCs), and 5V operation for enhanced noise immunity in harsh environments. A microcontroller (MCU) is a single-chip computer that contains a CPU, RAM, non-volatile program memory, and peripherals such as ADCs, timers, and communication interfaces. MCUs form the lowest tier of embedded computing hierarchy: microcontroller -> embedded processor -> SoC -> computing platform. PIC18 MCUs use a modified Harvard architecture with separate program and data buses, enabling single-cycle instruction execution while accessing both Flash and SRAM in the same cycle. Key features of the PIC18F26Q10 include 64 KB (64K x 8) of self-programmable Flash, 4 KB of SRAM, 256 bytes of EEPROM, and a 10-bit ADC with up to 24 channels. The device also integrates a 5-bit DAC, complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and CRC/SCAN hardware for functional safety. Its extended voltage range of 1.8V to 5.5V supports both battery and 5V regulated rails, and the Functional Safety (FuSa) classification simplifies IEC 61508 SIL-aware designs. Architecturally, the PIC18F26Q10 employs Microchip's enhanced mid-range core with a 16-bit instruction word and 8-bit data path, achieving 16 MIPS at 64 MHz. Configurable Logic Cells (CLCs) allow on-chip inter-peripheral routing without external glue logic, while the Peripheral Pin Select (PPS) enables flexible signal mapping to I/O pins. This combination reduces BOM count, PCB area, and firmware complexity for sensor nodes and motor control loops. Typical applications include industrial sensor nodes, IoT edge devices, low-power remote controls, home appliances, and automotive body controllers. The 5V tolerance and integrated op amps suit analog front-end designs where signal conditioning must coexist with digital control. Designers should enable the on-chip voltage regulator for 5V operation and use the CLCs to implement simple state machines that would otherwise require a CPLD. The PIC18F26Q10-E variant carries the extended operating temperature range of -40C to +125C suitable for industrial environments. This page synthesizes XAIPART distributor pricing, pin-compatible drop-in alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F26Q10-E/SP - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q10-E/SP

PIC18F26Q10-E/SP - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q10-E/SP is an 8-bit RISC microcontroller built on the PIC18 CPU core, operating up to 64 MHz with 64 KB of Flash program memory, 3.6 KB of SRAM and 256 bytes of EEPROM, housed in a 28-pin SPDIP (SP) through-hole package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, peripherals and I/O. Within the broader semiconductor taxonomy the PIC18F26Q10 belongs to the 8-bit MCU family, the PIC® XLP™ 18Q sub-family, and Microchip's Functional Safety (FuSa) line; it sits inside the microcontroller -> embedded controller -> power management-aware signal processing node class. Its 5V-native operation increases noise immunity for industrial sensor and real-time control nodes. Key features include a 10-bit ADC with computation (ADC2), a 5-bit DAC, two comparators, a zero-cross detect (ZCD), complementary waveform generator (CWG), 10-bit PWM with CCP, windowed watchdog timer (WWDT), hardware limit timer (HLT), CRC/SCAN accelerator, peripheral pin select (PPS) and four configurable logic cells (CLC). The CIP (Core Independent Peripherals) blocks let the CPU offload deterministic tasks, improving real-time response. Architecturally, the part uses an 8-bit modified Harvard bus with a 16-bit instruction word, a hardware multiplier and 49 instructions; the 64 MHz internal oscillator drives a 16 MIPS instruction throughput. The non-volatile memory is rated for high-endurance Flash and EEPROM suitable for frequent parameter storage. Typical applications include industrial sensor nodes, motor and pump control, white goods, automotive body and lighting subsystems, IoT edge nodes and low-power battery-powered metering. The Q10 family's noise-tolerant 5V I/O and CIP mix make it a strong fit for BLDC and AC-DC power-conversion auxiliary control. When designing, prefer using the CLCs and CWG for hard-real-time signaling, leave the WWDT enabled for safety, and use ADC2 computation modes to average the analog channel in hardware before waking the CPU. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18F26Q10-E/SS - 64KB Flash 8-bit MCU, 64MHz, 28-SSOP | Microchip
PIC18F26Q10-E/SS

PIC18F26Q10-E/SS - 64KB Flash 8-bit MCU, 64MHz, 28-SSOP | Microchip

The Microchip Technology PIC18F26Q10-E/SS is an 8-bit PIC18 XLP microcontroller featuring 64KB of Flash program memory, 4KB of SRAM, and 256 bytes of EEPROM, operating at up to 64MHz in a 28-pin SSOP (5.30mm body) package with extended (-40C to +125C) temperature grade. Designed for robust real-time control and sensor node applications, the PIC18F26Q10 family integrates intelligent analog peripherals, configurable logic cells (CLCs), and 5V operation for enhanced noise immunity in industrial environments. The part's broad peripheral set includes a 10-bit ADC with computation (ADC2), a 5-bit DAC, multiple PWM channels, a complementary waveform generator (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), and SCAN/CRC for functional safety applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals around an 8-bit data path. The PIC18 architecture is an enhanced 8-bit Harvard RISC core with 16-bit instructions, sitting within the broader hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor. PIC18 "XLP" parts target ultra-low-power designs, and the PIC18F26Q10 is part of Microchip's Functional Safety (FuSa) capable family with built-in CRC/SCAN for IEC 61508 SIL-aware designs. Key features include 25 general-purpose I/O pins, two 16-bit timers, configurable logic cells for custom hardware glue, zero-cross detect, and on-chip temperature indicator. The device supports 1.8V to 5.5V operation, providing flexibility across 3.3V and 5V rails common in industrial and consumer designs. The 28-SSOP package offers a compact, surface-mount form factor with a standard 0.65mm pin pitch. Typical applications include industrial control loops, IoT sensor nodes, touch-sensing front-ends, automotive body/comfort modules, and low-power battery-driven edge devices. The 5V tolerant I/O and integrated analog simplify designs that interface with legacy 5V sensors and actuators. When designing with this MCU, plan oscillator and ICSP layout to keep the ICSPDAT/ICSPCLK traces short, and verify CRC/SCAN configuration in MPLAB X Code Configurator (MCC) before code freeze for functional safety projects. The device supports in-circuit serial programming (ICSP) and debugging via Microchip's ICD tools. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the same PIC18 family, and practical design notes not always consolidated in the manufacturer datasheet.

Cotización Contacto
PIC18F26Q10-I/ML - 8-bit MCU, 64KB Flash, 64MHz, 28-QFN | Microchip
PIC18F26Q10-I/ML

PIC18F26Q10-I/ML - 8-bit MCU, 64KB Flash, 64MHz, 28-QFN | Microchip

The Microchip Technology PIC18F26Q10-I/ML is an 8-bit PIC microcontroller from the PIC18 Q10 family, featuring 64KB of Flash program memory, 3.6KB (3600 bytes) of SRAM, and 1024 bytes of EEPROM in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It operates up to 64 MHz, supports 2.3V to 5.5V supply voltage, and integrates intelligent analog peripherals including a 10-bit ADC, a 5-bit DAC, configurable logic cells, complementary waveform generators, and a hardware scan/CRC block for functional-safety applications. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a Harvard-architecture microcontroller based on an 8-bit data path with separate program and data buses, designed for deterministic real-time control. The PIC18 Q10 family sits within Microchip's broader PIC18 (8-bit) -> PIC microcontroller -> microcontroller -> embedded processor hierarchy, offering more peripherals, memory, and CIPs (Core Independent Peripherals) than baseline PIC10/12/16 parts. The "Q10" family name is a Microchip branding convention denoting the integrated analog and CIP feature set. Key features of the PIC18F26Q10-I/ML include Core Independent Peripherals that offload timing-critical tasks from the CPU, eXtreme Low Power (XLP) technology for energy-sensitive designs, 5V operation for increased noise immunity in industrial environments, and a Functional Safety (FuSa) feature set targeting IEC 61508 / SIL-capable applications. The 28-QFN package provides a small 6x6 mm footprint suitable for space-constrained sensor nodes and motor-control boards. Typical applications include IoT sensor nodes, real-time control loops, lighting ballast controllers, white-goods motor drivers, automotive body and sensor modules, and any cost-sensitive embedded design requiring deterministic CIP-based timing. The 5V tolerant I/O makes it well suited for industrial environments with long cable runs where ground bounce and EMI are concerns. When designing with this device, ensure proper decoupling (100 nF + bulk capacitor near VDD), review the device's errata for any CIP-specific limitations, and confirm whether the I/ML (28-QFN) package matches your PCB layout - the same PIC18F26Q10 die is also offered in SOIC-28, SSOP-28, and QFN-28 variants for layout flexibility.

Cotización Contacto
PIC18F26Q10-I/SO - 64KB Flash 8-bit MCU 64MHz SOIC-28 | Microchip
PIC18F26Q10-I/SO

PIC18F26Q10-I/SO - 64KB Flash 8-bit MCU 64MHz SOIC-28 | Microchip

The Microchip Technology PIC18F26Q10-I/SO is an 8-bit PIC® XLP™ microcontroller delivering 64 MHz CPU performance, 64 KB Flash, 4 KB SRAM and 1024 B EEPROM in a 28-pin SOIC (SO) package. It features an integrated 10-bit ADC with computation (ADC2), a 5-bit DAC, configurable PWM/CWG/HLT peripherals and a functional-safety (FuSa) capable core with WWDT and CRC/SCAN. A PIC18 microcontroller is an 8-bit Harvard-architecture RISC MCU from Microchip's PIC18 family, used widely in real-time control, sensor conditioning and low-power embedded applications. Within the broader taxonomy it sits under: 8-bit microcontroller -> microcontroller (MCU) -> embedded processor -> semiconductor. The Q10 sub-family specifically targets low-power (XLP), 5V-noise-immune designs with intelligent analog and rich configurable peripherals for sensor nodes and IoT endpoints. Key features of this part include 64 KB self-programmable Flash with program flash write/read protection, 1024 B high-endurance EEPROM rated for 100k erase/write cycles, four 16-bit timers, two USART modules, two SPI/I2C modules, 25-channel 10-bit ADC2 with hardware accumulation and threshold compare, a 5-bit DAC, two comparators and CWG (Configurable Logic Cell plus Complementary Waveform Generator). The CIP (Core Independent Peripherals) approach lets designers implement motor drive, lighting, power conversion and sensor signal chains without CPU intervention. Operating voltage spans 2.3V to 5.5V with 5V-tolerant digital I/O, allowing direct interface to noisy 5V industrial buses. Power-managed modes (Run/Idle/Doze/Sleep) plus Peripheral Module Disable (PMD) yield nanoWatt XLP sleep currents suitable for battery-powered sensor nodes. The functional-safety subsystem (Windowed WWDT, CRC, SCAN, HLT) supports IEC 60730 / Class B safety requirements in home appliances and industrial sensors. Typical applications include industrial control, robust sensor nodes, consumer electronics, automotive body and accessory modules, touch sensing, IoT edge nodes, and home appliance Class-B safety controllers. The device is particularly well-suited for designs migrating from older PIC16/PIC18F K-series parts that need modern CIP peripherals without leaving the 8-bit ecosystem. When designing with this part, ensure the 28-pin SOIC footprint matches your PCB land pattern (JEDEC MS-013) and that decoupling includes a 100 nF + bulk capacitor pair within a few millimeters of VDD/AVDD. The -I industrial temperature grade (-40C to +85C) and SOIC package suit through-hole-friendly wave soldering or hand rework on mixed-technology boards. This page synthesizes distributor pricing across DigiKey, Mouser, Win-Source and Octopart plus practical drop-in alternatives and design notes not found in the manufacturer datasheet itself.

Cotización Contacto
PIC18F26Q10-I/SS - 64KB Flash 8-bit MCU 28-SSOP | Microchip
PIC18F26Q10-I/SS

PIC18F26Q10-I/SS - 64KB Flash 8-bit MCU 28-SSOP | Microchip

The Microchip Technology PIC18F26Q10-I/SS is an 8-bit PIC® XLP™ microcontroller with 64KB Flash, 4KB RAM, and 256B EEPROM, operating up to 64MHz core clock in a 28-pin SSOP package. The device integrates intelligent analog peripherals including a 10-bit ADC with computation (ADC2), a 5-/10-bit DAC, configurable logic cells (CLCs), Complementary Waveform Generator (CWG), and hardware limit timer (HLT), all in a 5V-capable architecture with enhanced noise immunity. An 8-bit microcontroller (MCU) is a compact single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), non-volatile EEPROM, and digital/analog peripherals onto one silicon die. Within the broader taxonomy, the PIC18F26Q10 belongs to the 8-bit MCU category, which itself sits inside microcontrollers, which fall under integrated circuits (ICs), and ultimately semiconductors. The 'F' prefix denotes Flash program memory; 'Q10' identifies the family introduced for robust real-time control and sensor-node applications. Compared with 32-bit ARM Cortex-M MCUs, 8-bit PIC18 devices typically trade raw computational throughput for deterministic latency, lower power consumption, and lower BOM cost. Key features include 64KB self-programmable Flash with high-endurance program memory, 4KB SRAM, 256 bytes EEPROM, 25 general-purpose I/O pins, and a peripheral set encompassing two USART, two SPI, two I²C, 10-bit ADC2, 5-/10-bit DAC, CLC, CWG, HLT, Windowed WWDT, and CRC/SCAN. The 'I' suffix denotes the industrial -40°C to +85°C operating range, and the 5V-tolerant I/O architecture permits direct interfacing with legacy 5V logic. The device uses a Harvard RISC architecture with a 16-bit instruction word and an 8-bit data path, executing most instructions in a single cycle for a peak throughput of 16 MIPS at 64MHz. Core Independent Peripherals (CIPs) such as CLC and CWG can implement custom combinational/sequential logic and complementary PWM without CPU intervention, offloading deterministic tasks and reducing firmware complexity. Typical applications include industrial control nodes, sensor signal conditioning, touch and proximity interfaces, automotive LIN slave nodes, IoT edge devices, and consumer appliances. Designers should leverage the 5V-tolerant I/O for robust interfaces and use ADC2 with computation for sensor averaging and oversampling in low-power sensor hubs.

Cotización Contacto
PIC18F26Q10-I/STX - 64KB Flash 8-bit MCU 64MHz | Microchip
PIC18F26Q10-I/STX

PIC18F26Q10-I/STX - 64KB Flash 8-bit MCU 64MHz | Microchip

The Microchip Technology PIC18F26Q10-I/STX is a 28-pin VQFN (4x4 mm) 8-bit microcontroller from the PIC18-Q10 family, featuring 64KB of Flash program memory, 4KB SRAM, and 256 bytes of EEPROM, with a 64 MHz CPU core and integrated intelligent analog peripherals including a 10-bit ADC with Computation (ADC2), a 5-bit DAC, configurable peripherals, and 5V operation for increased noise immunity. Key features include the eXtreme Low Power (XLP) technology, Configurable Logic Cells (CLCs), Complementary Waveform Generator (CWG), Hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), SCAN/CRC functional safety features, and 25 MIPS CPU performance. The 28-VQFN (4x4) compact package is suitable for space-constrained designs while exposing all peripherals through dedicated pins. An 8-bit microcontroller (MCU) is a programmable computing device that executes instructions on 8-bit data words. The PIC18 family uses a modified Harvard RISC architecture with separate program and data buses, enabling single-cycle instruction execution. 8-bit MCUs occupy the lowest tier of the MCU hierarchy (8-bit -> 16-bit -> 32-bit), providing deterministic timing, low cost, and low power for applications where computational headroom of higher-bit MCUs is not required. They remain dominant in appliance control, sensor nodes, motor control, and industrial real-time control. The PIC18F26Q10 silicon integrates core-independent peripherals such as CLCs and the CWG that offload logic and waveform generation from the CPU, freeing MIPS for application code. Functional Safety (FuSa) features such as Flash ECC, SRAM parity, and WWDT simplify IEC 61508 / ISO 26262 safety system development. Typical applications include IoT sensor nodes, robust real-time control, appliance control, low-power edge sensing, touch/proximity human-machine interfaces, and motor control where 5V analog I/O and integrated digital peripherals reduce BOM cost. When designing with this MCU, plan pin allocation for the analog/digital shared pins early because the 28-VQFN package leaves no unused pins; ensure the PCB layout exposes the ICSP/PGD/PGC pins for in-circuit programming and provides a stable VDDCORE decoupling network. This page synthesizes DigiKey and Mouser distributor pricing, drop-in package-compatible alternatives from the PIC18-Q10 family, and practical design notes not duplicated in the Microchip datasheet.

Cotización Contacto
PIC18F26Q10T-I/SS - 8-Bit 64MHz 64KB Flash MCU 28-SSOP | Microchip
PIC18F26Q10T-I/SS

PIC18F26Q10T-I/SS - 8-Bit 64MHz 64KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC18F26Q10T-I/SS is an 8-bit PIC microcontroller from the PIC18-Q10 family, featuring 64KB Flash program memory in a 28-pin SSOP package. It operates at 64MHz, includes 4KB RAM and 256B EEPROM, and supports an industrial temperature range of -40C to +85C. The 'T' suffix indicates tape-and-reel packaging, while 'I' designates the industrial temperature grade and 'SS' refers to the SSOP-28 form factor. An 8-bit microcontroller (MCU) is a programmable semiconductor that integrates a CPU, memory, and peripheral interfaces onto a single chip, executing instructions one byte at a time and serving as the embedded control brain for countless consumer, industrial, and automotive products. The PIC18 family sits within Microchip's broader 8-bit MCU hierarchy (PIC10/12/16/18), which itself belongs to the microcontroller category under microcontrollers and digital ICs. Key features of the PIC18F26Q10 include 5V operation for increased noise immunity, integrated intelligent analog peripherals (10-bit ADC with computation, 5-bit DAC, comparators), configurable logic cells (CLCs), peripheral pin select (PPS) for flexible signal routing, and Core Independent Peripherals (CIPs) including CWG, HLT, WWDT, SCAN and CRC. The PIC18-Q10 family is optimized for real-time control and sensor node applications with functional safety (FuSa) features and XLP (eXtreme Low Power) technology. Architecturally, the device uses Microchip's enhanced PIC18 CPU core with hardware multiplier, support for both C and assembly programming via MPLAB X IDE, and a modified Harvard architecture enabling simultaneous instruction fetch and data access. The PIC18F26Q10 also provides up to 25 I/O pins, multiple communication peripherals (I2C, SPI, UART with LIN support), and PWM/SCCP modules for motor and power control. Typical applications include industrial sensor nodes, home appliance control, motor control loops, automotive body electronics, IoT edge devices, and battery-powered products requiring low standby current. The 5V capability makes this MCU especially suited to noise-tolerant environments like HVAC controls, white goods, and automotive subsystems where signal integrity over long harnesses is critical. When designing with the PIC18F26Q10, ensure the integrated high-performance signal routing (PPS) is configured early in the firmware to remap peripherals to the chosen pins. For low-power designs, leverage the XLP modes combined with the Windowed Watchdog Timer (WWDT) and Hardware Limit Timer (HLT) for autonomous safety behavior independent of CPU execution. This page synthesizes distributor pricing tiers, drop-in same-package alternatives drawn from the PIC18 family, practical MPLAB-based design notes, and parametric comparison data not assembled in any single manufacturer document.

Cotización Contacto
PIC18F26Q10T-I/STX - 64KB Flash 8-bit MCU | Microchip
PIC18F26Q10T-I/STX

PIC18F26Q10T-I/STX - 64KB Flash 8-bit MCU | Microchip

The Microchip PIC18F26Q10T-I/STX is an 8-bit PIC microcontroller from the PIC18-Q10 family, featuring 64KB Flash program memory, 4KB SRAM, and 256B EEPROM, operating at up to 64MHz in a 28-pin VQFN (4x4 mm) package with an industrial temperature grade (-40C to +85C). The device belongs to Microchip's eXtreme Low Power (XLP) family with Functional Safety (FuSa) capability and 5V operation for increased noise immunity in harsh environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and configurable peripherals onto one silicon die. PIC microcontrollers use a modified Harvard architecture with separate program and data buses, enabling single-cycle instruction execution and deterministic interrupt response. The PIC18 core family extends the baseline PIC16 instruction set with 16-bit instructions, a hardware multiplier, linear memory addressing, and prioritized interrupts, while remaining code-compatible with older PIC16 designs. Key features include a 10-bit ADC with Computation (ADC2), a 5-bit DAC, complementary waveform generators (CWG), hardware limit timer (HLT), windowed watchdog timer (WWDT), configurable logic cells (CLC), scan/CRC for code integrity, and up to 25 channels of 10-bit ADC. The integrated Core Independent Peripherals (CIPs) reduce CPU load and code complexity by handling timing-critical operations in hardware, enabling faster time-to-market for sensor node and real-time control applications. The PIC18F26Q10 architecture uses a 16-bit modified Harvard design with a 31-level hardware stack, eight priority levels for interrupts, and a single-cycle hardware multiplier for 8x8 signed/unsigned operations. The 5V operating range (1.8V-5.5V supply tolerance, 5V nominal logic) provides better noise margin than 3.3V-only MCUs, making the device well suited for industrial environments with motor or relay transients. Typical applications include IoT sensor nodes, home appliance control, motor control, LED lighting controllers, battery management front-ends, and automotive body electronics. The combination of XLP sleep currents below 50 nA and 5V analog performance allows battery-powered sensor designs with reliable industrial communication links. When designing with this part, allocate at least one UART, I2C, and SPI channel for sensor and host communication, and use the CLC to combine peripheral outputs without CPU intervention. Reserve the WWDT for fail-safe operation in safety-relevant applications; the scan/CRC peripheral provides firmware integrity verification for Functional Safety targets. This page synthesizes Microchip datasheet specifications, distributor pricing snapshots, drop-in same-package alternatives, and practical firmware/hardware design notes that are not aggregated on a single manufacturer page.

Cotización Contacto
PIC18F26Q43-E/SO - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q43-E/SO

PIC18F26Q43-E/SO - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q43-E/SO is an 8-bit RISC microcontroller from the PIC18-Q43 family, delivering 64 MHz CPU performance, 64 KB of Flash program memory, 4 KB of SRAM, and 1024 bytes of EEPROM in a 28-pin SOIC (Wide, 7.50 mm body) package. The -E suffix denotes an extended operating temperature grade of -40 °C to +125 °C, qualifying the device for industrial and automotive-grade environments. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash/ROM), volatile data memory (SRAM), non-volatile data memory (EEPROM), and configurable peripherals such as timers, communication interfaces, and analog blocks on a single silicon die. Within the broader taxonomy, the PIC18F26Q43-E/SO sits in the 8-bit MCU category, itself a subclass of embedded microcontrollers, which in turn fall under integrated circuits and semiconductors. The XLP™ (eXtreme Low Power) designation indicates power-optimized sleep modes engineered for battery-powered applications. Key differentiating features include a 12-bit Analog-to-Digital Converter with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) acquisition for advanced touch sensing, averaging, filtering, oversampling, and threshold comparison. The device integrates three 16-bit Pulse-Width Modulation (PWM) peripherals with new core-independent flexibility, a 12-bit differential ADC, an 8-bit DAC, six-channel DMA, and a zero-cross detect (ZCD) module. Voltage reference outputs of 1.024 V, 2.048 V, and 4.096 V provide calibrated precision references for ADC and comparator channels. Architecturally, the PIC18-Q43 family uses the high-performance PIC18 Harvard CPU core with hardware multiplier and C-aware instruction set, complemented by peripheral pin select (PPS) for flexible signal routing and CLC (Configurable Logic Cell) blocks for hardware-level customization without CPU intervention. The 5x UART (one supporting LIN/DMX/DALI), SPI, I2C, and DMA engine allow deterministic real-time control with minimal firmware overhead. Typical applications include capacitive touch user interfaces, LED lighting control with high-resolution dimming, motor control (BLDC/PMSM/stepper), sensor signal conditioning, battery-powered IoT nodes, and industrial control panels. The 28-SOIC package supports hand-soldering and standard reflow profiles, simplifying prototyping and low-volume manufacturing. When designing with this MCU, confirm that the supply voltage range of 1.8 V to 5.5 V matches your system rail and route PPS-reassigned pins carefully to avoid bus contention.

Cotización Contacto
PIC18F26Q43-E/SP - 64KB Flash 8-bit MCU 64MHz SPDIP-28 | Microchip
PIC18F26Q43-E/SP

PIC18F26Q43-E/SP - 64KB Flash 8-bit MCU 64MHz SPDIP-28 | Microchip

The Microchip PIC18F26Q43-E/SP is an 8-bit RISC microcontroller built on the PIC18 CPU core running at up to 64MHz, packaged in a 28-pin SPDIP (Skinny Plastic DIP) through-hole format. It integrates 64KB of Flash program memory, 4KB of SRAM data memory, and 1KB of EEPROM, with on-chip peripherals aimed at real-time control applications such as motor drive, lighting, power conversion, and capacitive touch sensing. An 8-bit microcontroller is a single-chip computer whose internal data path and arithmetic logic unit are 8 bits wide; the PIC18 family extends the classic PIC mid-range architecture with a 16-bit instruction word, linear memory, and a C-friendly compiler model. The PIC18F26Q43 belongs to the PIC18-Q43 sub-family, which sits within Microchip's broader PIC18 product hierarchy (PIC10/12/16/18 family -> 8-bit MCU -> microcontroller -> semiconductor). Q43 devices are distinguished by high-resolution peripherals that operate independently of the CPU (so-called Core Independent Peripherals, or CIPs). Key features of this device include a 12-bit Analog-to-Digital Converter with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) touch sensing, averaging, filtering, oversampling and threshold detection. The chip also integrates a 5-bit DAC, two comparators, three 16-bit dual-output PWMs (six PWM channels), Complementary Waveform Generator (CWG), CLC, Hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), zero-cross detect (ZCD), and scan/CRC engine. Vectored interrupt handling with selectable high/low priority delivers fixed three-instruction-cycle latency. Six DMA controllers move data between peripherals and memory without CPU intervention. Architecturally the device is implemented in CMOS with Microchip's eXtreme Low Power (XLP) technology, supporting down to nanoWatt sleep currents. Communication is provided by multiple UARTs, SPI, and I2C modules; timers include 8/16-bit timer/counters suitable for capture, compare, and PWM. The 64MHz system clock is derived from an internal 64MHz HFINTOSC or an external crystal, with PLL options. Typical applications include industrial automation, BLDC/PMSM motor control via the CWG and PWM peripherals, LED lighting drivers using the high-resolution PWM, capacitive touch user interfaces using the ADCC + CVD, USB-less consumer appliances, and general-purpose digital control loops. The wide 1.8V-5.5V VDD range simplifies battery-powered designs. When designing, ensure the device's ICE/ICD pins are routed to an in-circuit debugger header, the VDD/VSS pair has at least 100nF of decoupling near each pin pair, and the MCLR pull-up is sized for the in-system capacitance to avoid spurious resets. This page synthesizes distributor stock and pricing, drop-in Microchip alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten their evaluation and BOM decision.

Cotización Contacto
PIC18F26Q43-E/SS - 8-Bit 64MHz MCU, 64KB Flash, 28-SSOP | Microchip
PIC18F26Q43-E/SS

PIC18F26Q43-E/SS - 8-Bit 64MHz MCU, 64KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC18F26Q43-E/SS is an 8-bit PIC18 microcontroller running at up to 64 MHz core speed with 64 KB of Flash program memory, 4 KB of SRAM, and 256 bytes of EEPROM, housed in a 28-pin SSOP package with extended (-40C to +125C) operating range. It combines the legacy PIC18 instruction set with modern peripherals - six DMA controllers, three 16-bit dual PWMs providing six PWM outputs, a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting Capacitive Voltage Divider (CVD), configurable logic cells (CLCs), and an 8-bit DAC. According to the Microchip PIC18F26/46/56Q43 datasheet (document family DS40002171E), this device targets low-power real-time control applications. A PIC18 microcontroller is an 8-bit Harvard-architecture MCU from Microchip Technology belonging to the broader category of microcontrollers (MCU), which themselves sit inside the integrated circuits taxonomy (MCU -> 8-bit MCU -> PIC18 family -> peripheral-rich sub-family). The PIC18 core provides 16-bit wide instructions for compact code, deterministic interrupt latency of three cycles, and an instruction set that is forward-compatible with older PIC16 designs while adding vectored interrupts and a programmable vector table base address. Key features of the PIC18F26Q43 include 64 KB self-programmable Flash with program memory access partitions, hardware capacitive touch support via ADCC CVD, six DMA channels that move data without CPU involvement, three 16-bit PWMs (six outputs total), three CLCs for glue-logic customization, two comparators, two I2C, three UART, one SPI, and XLP (eXtra Low Power) technology. The 12-bit ADCC includes oversampling, averaging, and threshold-detection hardware that offloads common signal-conditioning tasks from the CPU. The architecture pairs a modified Harvard core with Core Independent Peripherals (CIPs) - blocks that operate without code intervention. CIPs like CLC, NCO, DSM, and the ADCC automate signal processing, allowing real-time responses measured in microseconds. Six DMA controllers move data between memory and peripherals without waking the CPU, enabling ultra-low-power average current profiles even with high peripheral throughput. Typical applications include capacitive touch user interfaces, LED lighting control, motor control with field-oriented control loops, IoT sensor nodes, automotive body and climate modules, and consumer appliance front-panel controllers. The wide temperature range and AEC-Q100-grade variants support harsh-environment deployments. When designing with this part, plan the brown-out and watchdog configuration early because the XLP Sleep current depends on which peripherals remain active. Designers should also review the vector-table base address feature when porting legacy PIC18 firmware, as it changes interrupt vector placement relative to classic PIC18 devices. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a single consolidated reference for sourcing and engineering decisions.

Cotización Contacto
PIC18F26Q43-I/SP - 8-bit 64MHz 64KB Flash MCU 28-SPDIP | Microchip
PIC18F26Q43-I/SP

PIC18F26Q43-I/SP - 8-bit 64MHz 64KB Flash MCU 28-SPDIP | Microchip

The Microchip Technology PIC18F26Q43-I/SP is an 8-bit PIC microcontroller in the PIC18-Q43 family, built around an enhanced mid-range RISC core and offered in a 28-pin SPDIP (0.300") through-hole package. The device integrates 64 KB of Flash program memory, 4 KB of SRAM, and 1 KB of EEPROM, and operates at up to 64 MHz across a 1.8 V to 5.5 V supply range, making it directly compatible with both 3.3 V and 5 V rails. According to the Microchip PIC18F26/46/56Q43 datasheet (Document 40002171E), the part is rated for the industrial temperature range of -40 °C to +85 °C. An 8-bit microcontroller (MCU) is a small, low-power processor on a single chip that combines a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and a set of on-chip peripherals such as timers, communication interfaces, and analog blocks. PIC microcontrollers use a modified Harvard architecture with separate program and data buses, and the PIC18 family extends the baseline 8-bit instruction set with hardware multiply, indexed addressing, and a C-friendly design. Within the Microchip portfolio, the PIC18 sits between the PIC16 baseline family and the 16-bit dsPIC/PIC24 family, targeting real-time control, sensor processing, and general-purpose embedded designs. Key features of the PIC18F26Q43 include a 12-bit Analog-to-Digital Converter with Computation (ADCC) that automates capacitive voltage-divider (CVD) touch sensing, averaging, filtering, oversampling, and threshold comparison. A new 16-bit Pulse-Width Modulation (PWM) peripheral, multiple Core Independent Peripherals (CIPs), and configurable logic cells let sophisticated hardware behaviour be implemented without CPU intervention. The device also integrates a 5-bit DAC, comparators, configurable communications (UART/SPI/I2C), and a windowed watchdog timer for functional-safety-capable designs. Typical applications for the PIC18F26Q43-I/SP include capacitive touch user interfaces, LED lighting control, sensor hub nodes, motor and fan control, low-cost IoT edge nodes, and industrial automation controllers. Its 64 KB Flash, 4 KB SRAM, and rich peripheral set allow designers to consolidate what would otherwise require an external ADC plus logic into a single 28-pin through-hole part, simplifying layout and BOM. When designing with this MCU, reserve a 100 nF decoupling capacitor close to each VDD pin, configure the MCLR pin correctly for in-circuit serial programming (ICSP), and review the ADCC sequencing if capacitive touch performance is critical. The 28-SPDIP footprint also makes it an easy hand-solderable option for prototypes, education, and field-service replacements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers an at-a-glance comparison against same-package PIC18 K-series and Q-series options.

Cotización Contacto
PIC18F26Q43-I/SS - 8-Bit 64MHz 64KB Flash MCU 28-SSOP | Microchip
PIC18F26Q43-I/SS

PIC18F26Q43-I/SS - 8-Bit 64MHz 64KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC18F26Q43-I/SS is an 8-bit PIC® XLP™ microcontroller with Functional Safety (FuSa) capabilities, integrating 64KB of Flash program memory and 4KB of RAM in a 28-pin SSOP package. It operates at up to 64MHz core clock speed, delivering high-performance deterministic control for real-time embedded applications. The device features a 12-bit Analog-to-Digital Converter with Computation (ADCC), three 16-bit Pulse-Width Modulators, a 6-channel DMA controller, an 8-bit DAC, and advanced Core Independent Peripherals (CIPs). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and peripherals around an 8-bit data path. The 8-bit MCU category occupies the broader hierarchy of microcontroller -> embedded processor -> semiconductor IC, and remains widely deployed for cost-sensitive deterministic control tasks. Functional Safety variants add documentation, development process rigor, and design features that help designers achieve IEC 61508 SIL capability and ISO 26262 ASIL capability at the system level. Key features include eXtreme Low Power (XLP) technology with nanoWatt sleep modes, hardware Custom Logic (CLC), Configurable Logic Cell (CLC), 16-bit PWM with complementary outputs and fault inputs, and zero-cross detection on the ADCC for capacitive voltage divider (CVD) touch sensing. The device operates from 1.8V to 5.5V, supports internal 64MHz oscillator, and offers multiple communication peripherals including UART, SPI, and I2C with SMBus support. The PIC18F26Q43 architecture uses a RISC-style Harvard bus with a 16-bit instruction word and 8-bit data path, featuring a hardware multiplier, interrupt controller with vector table, and peripheral pin select (PPS) for flexible I/O mapping. The integrated ADCC performs automated averaging, oversampling, threshold comparison, and accumulation, offloading signal-conditioning tasks from the CPU. Typical applications include capacitive touch user interfaces, LED lighting control with smooth dimming, motor control (BLDC, stepper, and brushed DC), functional safety systems, industrial sensor conditioning, and low-power battery-powered IoT nodes. The combination of CIPs and DMA enables complex timing chains to run without CPU intervention. When designing with this device, leverage the Peripheral Pin Select (PPS) feature to route digital peripherals to any available I/O pin, reducing PCB layout constraints. For functional safety designs, follow Microchip application note AN2950 and the Functional Safety data sheet supplement for diagnostic and failure-modes guidance. This page synthesizes distributor pricing, same-package drop-in alternatives drawn from Microchip's Q43 family and cross-brand 28-pin SSOP equivalents, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F26Q43T-I/STX - 8-bit 64MHz 64KB Flash MCU | Microchip
PIC18F26Q43T-I/STX

PIC18F26Q43T-I/STX - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F26Q43T-I/STX is an 8-bit PIC® XLP™ microcontroller running up to 64 MHz, with 64 KB of Flash program memory, 4 KB of SRAM, and 1 KB of EEPROM, housed in a 28-pin VQFN (4x4 mm) package. It belongs to the PIC18-Q43 family, which combines Core Independent Peripherals (CIPs) with advanced interconnection fabric for real-time control and capacitive-touch applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and integrated peripherals such as ADCs, timers, communication controllers, and GPIO. The PIC18 family sits within Microchip's 8-bit MCU portfolio and is widely deployed in consumer, industrial, and IoT designs where deterministic interrupt response, low power, and rich analog integration matter more than raw clock speed. Key features of this part include a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting capacitive voltage divider (CVD) touch sensing, three 16-bit dual PWMs providing six PWM outputs, six Direct Memory Access (DMA) controllers, vectored interrupts with selectable priority and 3-instruction-cycle fixed latency, and CLC (Configurable Logic Cell) hardware customization blocks. The device operates from 1.8 V to 5.5 V and includes XLP extreme-low-power sleep modes. The architecture is built on an enhanced PIC18 Harvard core with 16-bit instructions, a hardware multiplier, and a 31-level stack. Internal high-frequency oscillator, PLL, and low-power LFINTOSC minimize external components. Six DMA channels offload data movement between peripherals and memory, freeing the CPU for application logic and improving real-time response in motor control, lighting, and sensor-fusion designs. Typical applications include capacitive touch user interfaces, BLDC/PMSM motor control using the 16-bit PWMs and PGA-equipped ADCC, LED lighting and signage controllers, IoT sensor nodes, battery-powered consumer appliances, and industrial control front-ends. The combination of XLP sleep currents and DMA-driven peripherals enables long battery life in always-on systems. When designing with the PIC18F26Q43T-I/STX, follow Microchip AN2931 and AN2407 for PCB layout guidelines, place a 0.1 µF decoupling capacitor on each VDD pin with trace length under 5 mm, and use the MPLAB X IDE with MPLAB Code Configurator (MCC) for peripheral setup. Keep in mind that the 28-pin VQFN variant differs from the 28-pin SPDIP/SOIC variants only in thermal pad connection—review the pinout diagram before routing. This page synthesizes distributor pricing, drop-in alternatives within the PIC18-Q43 family, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18F26Q84-E/SO - 8-bit MCU, 64KB Flash, CAN FD, 28-SOIC
PIC18F26Q84-E/SO

PIC18F26Q84-E/SO - 8-bit MCU, 64KB Flash, CAN FD, 28-SOIC

The Microchip Technology PIC18F26Q84-E/SO is an 8-bit PIC microcontroller with 64KB Flash, 64 MHz CPU speed, and Controller Area Network Flexible Data Rate (CAN FD) support, housed in a 28-pin SOIC (SO) wide-body package. It integrates an extensive set of Core Independent Peripherals (CIPs) including CWG, CCP, DSM, NCO, math accelerator, 12-bit ADC, and high-speed comparators, enabling deterministic real-time control without CPU intervention. What is a PIC18-Q84 microcontroller? The PIC18-Q84 family is part of Microchip's 8-bit PIC microcontroller portfolio, combining Core Independent Peripherals (CIPs) with CAN FD connectivity for automotive and industrial applications. These cost-optimized MCUs include time-saving CIPs in 28/40/44/48-pin packages, sit within the broader PIC18 family of 8-bit microcontrollers, and address the category of small-footprint, low-power embedded controllers for sensor and actuator networks. Key features include 64 KB Flash program memory, 4 KB SRAM, 1 KB EEPROM, a 12-bit differential ADC with Computation, up to six PWM channels, two UART, two SPI, two I2C, two CAN FD, and an integrated math accelerator for sensor math pipelines. The device operates from 2.3V to 5.5V and is qualified for the -40C to +125C extended industrial temperature range, supporting harsh-environment deployments. The PIC18F26Q84 architecture pairs a Harvard RISC CPU with a rich CIP block, allowing hardware-driven peripheral actions (e.g., ADC-triggered PWM, timer-triggered ADC) that free the core for higher-level tasks. This CIP-based design yields deterministic latency and reduced firmware complexity compared with CPU-driven interrupt architectures, while the on-chip CAN FD peripheral brings automotive-grade bus bandwidth for sensor and actuator networks. Typical applications include CAN-based sensor nodes, automotive body and chassis ECUs, industrial automation controllers, building automation gateways, and battery management systems. The wide temperature range and CAN FD make it especially well suited to vehicle networks and factory-floor control loops requiring deterministic, real-time response. Design consideration: when using CAN FD, ensure that the bit-time configuration matches the chosen CAN transceiver and bus topology; for 28-pin SOIC layouts, dedicate adequate copper to the exposed thermal pad area to keep junction temperature within range at full CPU speed. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto