Microcontroladores

Productos (18747)

ATSAMD21J17D-MU - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip
ATSAMD21J17D-MU

ATSAMD21J17D-MU - 48MHz Cortex-M0+ MCU 128KB Flash | Microchip

The Microchip Technology ATSAMD21J17D-MU is a 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D21J family, featuring 128KB of Flash, 16KB of SRAM, and a 48MHz CPU core in a 64-pin QFN (9x9 mm) package with industrial temperature rating (-40C to +85C). What is an ARM Cortex-M0+ microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The Cortex-M0+ is ARM's smallest and most energy-efficient 32-bit core, optimized for cost-sensitive embedded applications that still need 32-bit performance and modern peripherals. The ATSAMD21J17D-MU integrates this core with 128KB of embedded Flash, 16KB SRAM, a 4KB read-while-write (RWW) Flash section, and a rich peripheral set including USB, CAN, SERCOM, ADC, DAC, and timers. Key features of the ATSAMD21J17D-MU include the Cortex-M0+ core with 48MHz operation (96 CoreMark), full-speed USB 2.0 with on-chip transceiver, an 8-channel 12-bit 350ksps ADC, a 10-bit 350ksps DAC, up to six SERCOM (serial communication) interfaces, six 16-bit timers/counters, and a Peripheral Touch Controller (PTC) for capacitive touch interfaces. The device operates from 1.62V to 3.63V and integrates an Event System for deterministic peripheral-to-peripheral signaling without CPU intervention. The SAM D21 architecture combines the Cortex-M0+ core with Microchip's proprietary peripheral set, achieving low active current and flexible SleepWalking power management per peripheral. The 64-QFN exposed-pad package provides 52 programmable I/O pins and excellent thermal performance for hand-held and industrial designs. Typical applications include USB human-interface devices (HID), home automation gateways, low-power sensor nodes, industrial control boards, consumer remote controls, and capacitive-touch user interfaces. The combination of USB, ADC/DAC, and flexible serial interfaces addresses a broad range of connected-product designs. When designing with this device, pay close attention to decoupling (one 100nF plus one 4.7uF bypass near each supply pin) and to the exposed thermal pad requirement for proper heat dissipation. Programmability is supported by Atmel Studio/Microchip Studio, MPLAB X IDE, and the SAMD21 support package in the Arduino core, with debug via SWD through the standard 2-wire interface. This page synthesizes distributor pricing, drop-in SAMD21 alternatives, and practical hardware-design notes not found in the manufacturer datasheet. Pricing is referenced as of 2026-09-21 and reflects authorized-distributor data; consult distributors for current stock and lead time.

Cotización Contacto
ATSAMD21J18A-AF - 48MHz Cortex-M0+ 256KB Flash MCU | Microchip
ATSAMD21J18A-AF

ATSAMD21J18A-AF - 48MHz Cortex-M0+ 256KB Flash MCU | Microchip

The Microchip ATSAMD21J18A-AF is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21J family, integrating 256KB of Flash and 32KB of SRAM while operating at up to 48MHz (2.46 CoreMark/MHz), housed in a 64-pin TQFP (10x10 mm) industrial-grade package. It is built on a low-power architecture designed for always-on connected products, drawing as little as 70 uA/MHz in active mode and supporting deep-sleep currents in the single-digit microamp range. An ARM Cortex-M0+ microcontroller is a 32-bit reduced instruction set computing (RISC) processor core targeting ultra-low-power embedded applications. The Cortex-M0+ belongs to the ARM Cortex-M family -> 32-bit MCU core -> embedded processor -> semiconductor. It executes the Thumb/Thumb-2 instruction set, includes a single-cycle hardware multiplier, and is paired in the SAM D21 with Microchip's event system, SERCOM peripherals, and a rich analog set. By occupying the low-power end of the ARM-M lineup, Cortex-M0+ parts are commonly chosen over Cortex-M3/M4 when deterministic control, low BOM cost, and battery life outweigh raw compute. The ATSAMD21J18A-AF features a 12-bit, up to 350 ksps ADC with hardware oversampling, a 12-bit 1 Msps DAC, two analog comparators, six SERCOM modules (each configurable as UART/USART/SPI/I2C), up to 52 GPIO, and a full-speed USB 2.0 device/host interface. The integrated 2.46 CoreMark/MHz efficiency is supported by a single-cycle hardware multiplier, a deterministic nested-vectored interrupt controller (NVIC), and dual-bank Flash for safe in-field OTA updates. Typical applications include IoT sensor nodes, home automation gateways, smart appliances, industrial metering, wearable fitness bands, and consumer HMI with USB-CDC connectivity. The wide 1.6V to 3.6V supply range, on-chip FPU-less Cortex-M0+ pipeline, and dual-bank Flash make it well suited to mains-powered as well as coin-cell products. When designing with this part, reserve SERCOM channel assignments early because each SERCOM is pin-muxed and conflicts are easy to miss at low pin counts. Always enable the brown-out detector (BOD) and configure the SysTick for low-power tickless RTOS operation to maximize battery life. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes that are not bundled together on the manufacturer datasheet PDF.

Cotización Contacto
ATSAMD21J18A-AFT - 32-bit Cortex-M0+ MCU, 256KB Flash, 64-TQFP | Microchip
ATSAMD21J18A-AFT

ATSAMD21J18A-AFT - 32-bit Cortex-M0+ MCU, 256KB Flash, 64-TQFP | Microchip

The Microchip ATSAMD21J18A-AFT is a 32-bit ARM Cortex-M0+ flash microcontroller from the SAM D21J family, delivering 48 MHz CPU performance with 256 KB Flash and 32 KB SRAM in a 64-pin TQFP (10x10 mm) package. It is specified for the extended industrial temperature range of -40C to +125C and operates from a 1.62 V to 3.63 V supply. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The Cortex-M0+ core from ARM is the smallest and most energy-efficient ARM core, optimized for deterministic embedded control and low active power. The SAM D21J family extends this core with rich peripherals including SERCOM, ADC, DAC, and event system, placing the MCU in the broader hierarchy: microcontroller -> embedded processor -> semiconductor device. Key features of the ATSAMD21J18A-AFT include 6 SERCOM serial communication interfaces (each configurable as UART/SPI/I2C), a 12-bit 1 MSPS ADC with up to 20 channels, a 10-bit DAC, full-speed USB device/host, and a 2-channel DMAC for low-overhead data movement. The device supports sleepwalking peripherals and idle/standby modes that drop quiescent current to single-digit microamps, enabling years of battery life in sensor applications. The ATSAMD21J18A-AFT is functionally safety-capable (FuSa) and integrates the ARM Cortex-M0+ core with single-cycle multiplier, hardware divide, and a Nested Vectored Interrupt Controller (NVIC). A 32-channel event system allows peripherals to trigger one another without CPU intervention, reducing wake latency and energy. The device also includes a segmented LCD controller variant in the family, but the -J18A part focuses on connectivity-rich general-purpose applications. Typical applications include home automation gateways, IoT sensor nodes with USB connectivity, industrial metering, low-end consumer HMI, smart thermostats, and wearable fitness devices. The extended -40C to +125C temperature range supports outdoor and industrial enclosures. Designers should plan PCB layout carefully: place the 0.1 uF decoupling capacitor within 2 mm of each VDD pin, provide a solid ground pour under the device, and route the D+/D- lines as a 90-ohm differential pair with no stubs. The internal voltage regulator requires both a VDDCORE and VDDIO supply pin to be decoupled. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
ATSAMD21J18A-AU - ARM Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD21J18A-AU

ATSAMD21J18A-AU - ARM Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip ATSAMD21J18A-AU is a 32-bit ARM Cortex-M0+ microcontroller from the SAM D21 family, featuring 256KB of Flash and 32KB of SRAM in a 64-pin TQFP (10x10 mm) package. The device operates at up to 48 MHz, reaching 2.46 CoreMark/MHz, and supports a 1.62V to 3.6V supply voltage with multiple low-power sleep modes. The suffix –AU denotes the TQFP-64 tray packaging variant of the SAM D21J series. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory (Flash for code and SRAM for data), and a rich set of peripherals on a single silicon die. ARM Cortex-M0+ cores are the smallest and most energy-efficient members of the ARM Cortex-M family, optimized for deterministic embedded control and ultra-low-power operation. The SAM D21 family specifically targets battery-powered and always-on IoT, consumer, and industrial applications where low active current, deep-sleep retention, and integrated analog peripherals reduce bill-of-materials cost. Key features include a full-speed USB 2.0 device/host interface, up to six SERCOM configurable serial communication modules, a 12-bit 350 ksps ADC with up to 20 channels, two 12-bit DACs, three analog comparators, up to 52 GPIO pins with interrupt capability, and a powerful peripheral event system for inter-peripheral signaling without CPU intervention. Hardware touch support, a CRC engine, and a true random number generator (TRNG) are also integrated. The ATSAMD21J18A-AU is built on a low-leakage process and features an advanced peripheral touch controller, two 24-bit timers, RTC, and a 16-bit PWM with dead-time generators suitable for motor and power control. Its bootloader is pre-loaded in ROM, enabling in-system programming over USB or UART without external programmer hardware. Typical applications include home automation gateways, smart metering, industrial sensor nodes, USB HID input devices, LED lighting controllers, wearable fitness bands, and consumer electronics with capacitive touch user interfaces. The wide 1.62–3.6V supply range and integrated USB PHY simplify designs that previously required an external voltage regulator. When designing with the ATSAMD21J18A-AU, consider the thermal envelope of the TQFP-64 package, ensure proper decoupling with 100 nF + 4.7 uF bulk capacitors near each supply pin, and follow the trace-impedance recommendations for the USB differential pair (D+/D-) to maintain USB compliance. This page synthesizes live distributor pricing, drop-in SAMD21J18A family variants, and practical design notes that are not present in the manufacturer datasheet PDF, helping engineers select the right SAMD21 member for production.

Cotización Contacto
ATSAMD21J18A-AUT - 32-bit Cortex-M0+ MCU 256KB Flash 64-TQFP | Microchip
ATSAMD21J18A-AUT

ATSAMD21J18A-AUT - 32-bit Cortex-M0+ MCU 256KB Flash 64-TQFP | Microchip

The Microchip Technology ATSAMD21J18A-AUT is a low-power, high-performance 32-bit ARM Cortex-M0+ microcontroller running up to 48 MHz, with 256 KB of Flash and 32 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package supplied on Tape & Reel. It belongs to the SAM D21J family, the highest-pin-count variant of the SAM D21 series with the largest I/O count of the family. What is a Cortex-M0+ microcontroller? An MCU (microcontroller unit) is a single-chip computer integrating a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals. The ARM Cortex-M0+ is the most energy-efficient core in the Cortex-M family, optimized for low-power embedded designs. The ATSAMD21J18A-AUT sits in the power-management IC and microcontroller hierarchy as an industrial-grade general-purpose MCU suitable for home automation, consumer, metering, and industrial applications. Key features of this part include a full-speed USB 2.0 device/host with on-chip transceiver, up to six SERCOM (serial communication) interfaces configurable as UART/SPI/I2C, a 12-bit 350 ksps ADC with up to 20 channels, two analog comparators, a 10-bit 350 ksps DAC, up to six 16-bit timer/counters, a 32-bit RTC, and a Peripheral Touch Controller (PTC) for capacitive touch sensing. The device operates from 1.62 V to 3.63 V and includes a built-in DMA controller, Event System, and SleepWalking peripherals for sub-microamp sleep current. The ATSAMD21J18A-AUT uses a two-cycle pipeline Harvard architecture with single-cycle I/O access and a hardware multiplier, providing 0.9 DMIPS/MHz CoreMark performance. On-chip voltage regulation and an integrated POR/BOD circuit simplify power-tree design and reduce BOM count in 3.3 V systems. Typical applications include IoT sensor nodes, USB HID devices, smart-home controllers, industrial HMI panels, and low-power wireless sensor hubs. The combination of USB, SERCOM, ADC, DAC, and touch sensing makes the part flexible for multi-protocol gateways. Designers should consult the device 40001882A datasheet for full peripheral mapping and the SAME70/SAM D21 Xplained Pro board schematics for reference designs.

Cotización Contacto
ATSAMD21J18A-CU - 256KB Flash 48MHz Cortex-M0+ MCU | Microchip
ATSAMD21J18A-CU

ATSAMD21J18A-CU - 256KB Flash 48MHz Cortex-M0+ MCU | Microchip

The Microchip ATSAMD21J18A-CU is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller in the SAM D21J family, featuring 256 KB of Flash and 32 KB of SRAM, packaged in a 64-ball UFBGA (CU) with operating voltage 1.62V to 3.6V and a maximum CPU frequency of 48 MHz (delivering up to 2.46 CoreMark/MHz). The device integrates six SERCOM serial-communication channels (configurable as UART/SPI/I2C), one full-speed USB 2.0 interface with embedded PHY, a 12-bit 1 MSPS ADC, 10-bit DAC, up to 8 timer/counter channels, and a 48 MHz Digital Frequency Locked Loop (DFLL48M) with on-chip temperature and voltage references. According to the Microchip SAM D21 family datasheet, the part is rated for the industrial 85C temperature grade and supports sleepwalking peripherals for event-driven low-power operation. What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a 32-bit reduced instruction set computing (RISC) MCU implementing the ARMv6-M architecture; it sits in the hierarchy microcontroller -> 32-bit MCU -> embedded processor, with Cortex-M0+ being the smallest, lowest-power core in the ARM Cortex-M lineup. Microcontrollers in this class integrate Flash, SRAM, peripherals, and a CPU core into a single chip, targeting deterministic embedded control in cost- and power-constrained designs. The ATSAMD21J18A is part of Microchip's Atmel SMART SAM D family, designed for low-power connected embedded applications. Key features of the ATSAMD21J18A-CU include 256 KB Flash with error correction, 32 KB SRAM, six SERCOM peripherals that can be mapped to almost any GPIO, a 12-channel 12-bit ADC with oversampling, a 10-bit DAC, and a capacitive touch hardware peripheral. The CPU is a 32-bit Cortex-M0+ with single-cycle hardware multiply, MPU, and Micro Trace Buffer support for debug, while the on-chip DFLL48M and fractional PLL enable precise 48 MHz operation from low-frequency crystal references. Architecturally, the ATSAMD21J18A uses a low-leakage process with multiple power domains and idle/standoff/backup sleep modes reaching below 1 uA retention current. The peripheral event system allows hardware-triggered actions without CPU intervention, and the SERCOM channel architecture lets each instance be software-configured as UART, SPI, or I2C for flexible pin allocation. Typical applications include home automation gateways, low-power wireless sensor nodes (e.g. LoRa/BLE host MCUs), USB HID devices, consumer electronics HMI, industrial metering, and battery-powered IoT endpoints. The USB PHY and SERCOM channels support direct USB device stacks without an external PHY, simplifying HID/CDC/Mass Storage product designs. For design-in, plan the UFBGA-64 land pattern carefully - this 0.65 mm-pitch BGA requires NSMD pads, microvia fan-out, and careful reflow profiling to avoid tombstoning. Also confirm the chosen compiler toolchain (GCC arming-none-eabi, IAR, Keil) supports the Cortex-M0+ core with the SAM D21 device pack. This page synthesizes distributor pricing, qualified drop-in alternatives, and engineering design notes beyond the manufacturer datasheet, giving procurement and design engineers a single source for selection, replacement, and BOM validation.

Cotización Contacto
ATSAMD21J18A-CUT - 256KB Flash Cortex-M0+ MCU 64-BGA | Microchip
ATSAMD21J18A-CUT

ATSAMD21J18A-CUT - 256KB Flash Cortex-M0+ MCU 64-BGA | Microchip

The Microchip ATSAMD21J18A-CUT is a low-power, high-performance 32-bit ARM Cortex-M0+ flash microcontroller with 256KB of flash and 32KB of SRAM, operating up to 48 MHz in a 64-ball UFBGA package (CUT suffix denoting the UFBGA-64 package, tape and reel). It integrates up to 256KB flash, 32KB SRAM, a full-speed USB 2.0 device, six SERCOM interfaces, a 12-bit 350ksps ADC, 10-bit DAC, and up to 48 GPIO pins in the 64-pin package option, supporting 1.6V to 3.6V supply operation. A microcontroller (MCU) is an integrated circuit that combines a processor core, memory, and programmable peripherals on a single chip, forming the smallest complete compute platform in an embedded system. The Cortex-M0+ family sits at the most energy-efficient end of the ARM Cortex-M hierarchy, prioritizing low power and deterministic interrupt response over peak throughput. Microchip's SAM D21 family extends this with rich analog, USB, and capacitive touch peripherals, placing the SAM D21 in the broader taxonomy: ARM Cortex-M0+ -> Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. It is pin-compatible with the SAM D20 family, enabling easy upgrades. Key features include a 2.46 CoreMark/MHz performance figure, six SERCOM-configurable serial channels, an Event System for inter-peripheral signaling without CPU intervention, and a Peripheral Touch Controller supporting buttons, sliders, and wheels. The device provides 6 channel DMA, two I2S interfaces, and a built-in full-speed USB 2.0 device with on-chip transceiver, simplifying USB-connected designs. Architecturally, the SAM D21 uses a single-cycle I/O port write architecture and an efficient bus matrix that allows simultaneous access to flash, SRAM, and peripherals. SleepWalking peripherals draw near-zero current while still being able to wake the core on events, and the Event System routes peripheral signals without CPU involvement. Six flexible SERCOM peripherals can each be independently configured as UART, SPI, or I2C, removing the need for fixed peripheral counts. Typical applications include USB-enabled home automation nodes, consumer HID devices like keyboards and mice, industrial sensor hubs, smart energy metering, capacitive touch user interfaces, and wearable fitness trackers. The combination of low active power, deep-sleep modes below 1 µA, and integrated USB makes the ATSAMD21J18A a common choice for battery-powered connected devices. When designing with this part, allocate adequate decoupling (100 nF per VDD pin plus a bulk 4.7 µF), route the USB D+/D- traces as a 90 Ω differential pair, and verify the chosen boot configuration matches your fuse settings. The 64-ball UFBGA requires PCB via-in-pad or careful escape routing; for prototypes, consider the QFN/64 variant instead. This page synthesizes distributor pricing, same-brand pin-compatible variants, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
ATSAMD21J18A-MF - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip
ATSAMD21J18A-MF

ATSAMD21J18A-MF - 48MHz Cortex-M0+ MCU 256KB Flash | Microchip

The Microchip Technology ATSAMD21J18A-MF is a 32-bit ARM Cortex-M0+ flash microcontroller operating at up to 48 MHz with 256 KB Flash and 32 KB SRAM, housed in a 64-pin QFN (9x9 mm) package. The device integrates a 12-bit ADC, 10-bit DAC, multiple SERCOM interfaces, full-speed USB, and a 2.46 CoreMark/MHz performance rating, making it suitable for connected sensor nodes, consumer electronics, and industrial control systems. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and I/O on a single silicon die. The Cortex-M0+ is the most energy-efficient member of the ARM Cortex-M family, designed for deterministic real-time embedded workloads with a two-stage pipeline, single-cycle I/O port access, and an optional Micro Trace Buffer. SAM D21 microcontrollers extend the M0+ with Microchip's peripheral set, event system, and SleepWalking peripherals, positioning the family between 8-bit AVR/PIC parts and higher-cost Cortex-M4 parts. Key features include 256 KB Flash, 32 KB SRAM, 48 MHz max CPU clock, a 12-bit 350 kSPS ADC with up to 20 channels, a 10-bit 350 kSPS DAC, six SERCOM modules configurable as UART/SPI/I2C, one full-speed USB 2.0 device/host port, up to 52 GPIO, and a 1.62-3.63 V operating voltage range. The device supports Sleep, Idle, Standby, and Backup sleep modes with typical active current around 3 mA at 48 MHz and standby currents in the single-digit microamp range. The SAM D21 architecture pairs the Cortex-M0+ core with a 4-channel DMA controller, an Event System for inter-peripheral signalling without CPU intervention, and a SleepWalking power-management scheme that wakes selected peripherals only when matched events occur. Hardware math accelerators and CRC-32 reduce firmware overhead for sensor-fusion and packet-handling tasks. Debug is via SWD with an optional Micro Trace Buffer; programming is supported through Atmel-ICE, MPLAB X, and the Arduino IDE via the MKR/Zero board variants. Typical applications include smart-home and home-automation hubs, low-power wireless sensor nodes, USB HID peripherals, battery-powered consumer devices, industrial metering, and motor-control front-ends. The wide 1.62-3.63 V supply range and integrated USB transceiver simplify lithium-battery designs with bus-powered accessories. AEC-Q100 variants are available in the SAM D21J family for automotive body and chassis applications. When designing with this part, budget Flash and SRAM for bootloader + application coexistence and verify the 64-pin QFN PCB footprint against the manufacturer's land-pattern recommendation. Use the SERCOM multiplexing tables early in the pin-out assignment to avoid conflicting peripheral mappings. This page synthesizes distributor pricing, drop-in pin-compatible alternatives across the SAM D20/D21 families, and practical design notes not collated in the manufacturer datasheet, giving engineers a one-stop view for sourcing and substitution decisions.

Cotización Contacto
ATSAMD21J18A-MFT - 48MHz Cortex-M0+ MCU, 256KB Flash, 64-QFN
ATSAMD21J18A-MFT

ATSAMD21J18A-MFT - 48MHz Cortex-M0+ MCU, 256KB Flash, 64-QFN

The Microchip Technology ATSAMD21J18A-MFT is a 32-bit ARM Cortex-M0+ flash MCU from the SAM D21 family, delivering 48 MHz core speed with 256 KB Flash and 32 KB SRAM in a 64-pin QFN (9x9 mm) package. It integrates USB 2.0 Full-Speed, up to six SERCOM interfaces (configurable as I2C/SPI/UART), a 12-bit 350 ksps ADC, a 10-bit DAC, and a capacitive touch (PTC) peripheral. Operating from 1.62 V to 3.63 V, the device targets industrial-grade -40C to +125C environments and supports low-power Sleep, Standby, and Backup modes down to a few microamps. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and a set of on-chip peripherals. The ATSAMD21J18A-MFT's Cortex-M0+ core sits at the entry level of the 32-bit ARM Cortex-M family, balancing low power with deterministic interrupt response. The SAM D21 series is positioned within Microchip's portfolio between the lower-pin SAM D10/D11 and the larger SAM D20/D21 family variants. With on-chip USB and SERCOM multiplexing, it consolidates what would otherwise require multiple external components. Key features include 256 KB Flash organized as 256K x 8, 32 KB SRAM, six SERCOM modules (each independently configurable), full-speed USB device/host with on-chip transceiver, a 12-bit ADC with up to 20 channels, two I2S interfaces, and a peripheral touch controller. AES 32-bit crypto accelerator and a true random number generator (TRNG) support secure applications. The integrated 32 kHz RTC oscillator and PLL-enable flexible clocking from internal or external sources. The architecture pairs a Cortex-M0+ core with Microchip's SERCOM peripheral set and an event system that allows peripherals to interact without CPU intervention, freeing cycles for application logic. The 48 MHz clock with single-cycle multiplier achieves 2.46 CoreMark/MHz. The part is Functional Safety (FuSa) capable, supporting IEC 60730 class B libraries available separately. Typical applications include industrial sensor nodes, home automation gateways, USB peripherals (HID/CDC/MSC), low-power IoT edge nodes, smart metering, consumer HID devices, and small touchscreen human-machine interfaces. The integrated USB avoids external PHY chips, reducing BOM cost. Design consideration: place a 1 uF plus 100 nF decoupling network near each power pin; ensure the D+ and D+ trace impedance matches 90 ohms differential per USB specification. Use the sleepwalking idle peripherals mode to achieve sub-100 uA average system power. This page synthesizes distributor pricing, drop-in SAMD21 alternatives, and practical low-power design notes not found in the standalone manufacturer datasheet.

Cotización Contacto
ATSAMD21J18A-MUT - 48MHz ARM Cortex-M0+ 256KB Flash MCU | Microchip
ATSAMD21J18A-MUT

ATSAMD21J18A-MUT - 48MHz ARM Cortex-M0+ 256KB Flash MCU | Microchip

The Microchip Technology ATSAMD21J18A-MUT is a 32-bit ARM Cortex-M0+ based flash microcontroller running at up to 48 MHz with 256 KB of Flash and 32 KB of SRAM, housed in a 64-pin 9x9 mm QFN package. Part of the SAM D21J family with Functional Safety (FuSa) features, the device integrates a rich peripheral set including a 12-bit ADC, 10-bit DAC, USB 2.0 Full Speed, six SERCOM interfaces, and a 6-channel Event System. Operating from 1.62 V to 3.63 V, the ATSAMD21J18A targets battery-powered and energy-conscious embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and configurable peripherals. The ARM Cortex-M0+ is a 32-bit processor core optimized for low-power, deterministic embedded applications and sits within the broader ARM Cortex-M family hierarchy (Cortex-M0 -> Cortex-M0+ -> Cortex-M3 -> Cortex-M4 -> Cortex-M7). The SAM D21 family occupies the entry-level, low-power end of the Microchip Cortex-M lineup; within that family, the ATSAMD21J18A variant provides the largest pin count (64 pins) and largest Flash option, enabling connectivity-rich designs that smaller-pinned SAMD21G or SAMD21E variants cannot serve. Key features include 256 KB Flash, 32 KB SRAM, full-speed USB 2.0 with on-chip transceiver, six SERCOM modules that can each be configured as UART, SPI, or I2C, a 12-bit 350 ksps ADC with up to 20 channels, a 10-bit DAC, and two analog comparators. SleepWalking peripherals and the Event System allow the core to remain in deep sleep while peripherals react autonomously, drawing only a few microamps. The device is built on a low-power CMOS process and supports six software-selectable sleep modes (IDLE, STANDBY, BACKUP, OFF) with sub-microsecond wake-up. The integrated Full-Speed USB PHY eliminates external crystal requirements for USB, while SERCOM multiplexing lets designers assign digital interfaces to most GPIO pins, simplifying PCB routing across board variants. Typical applications include home automation gateways, consumer electronics, smart metering, industrial sensor nodes, USB peripherals (HID, CDC, mass storage), wearable fitness devices, and low-power IoT end nodes. The wide operating voltage and rich peripheral mix make it well suited for battery-powered products requiring USB connectivity or multiple serial interfaces. When designing with the ATSAMD21J18A, use MPLAB X IDE or Microchip Studio with the ASF/Atmel Software Framework, and program/debug with an Atmel-ICE or MPLAB Snap. Decouple VDDCORE and VDDIO with at least 100 nF plus 4.7 uF bulk capacitors placed as close to the pins as possible. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers evaluate the ATSAMD21J18A-MUT for new designs or as a substitute for other Cortex-M0+ MCU candidates.

Cotización Contacto
ATSAMD51G18A-MF - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAMD51G18A-MF

ATSAMD51G18A-MF - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD51G18A-MF is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit (FPU), integrating 256 KB Flash and 128 KB SRAM in a 48-pin QFN (7x7 mm) package with extended temperature range. It belongs to Microchip's SAM D51 family, designed for high-performance embedded applications demanding DSP, USB, and rich connectivity. An ARM Cortex-M4F MCU is a microcontroller built around the ARM Cortex-M4 processor core augmented with a hardware single-precision floating-point unit and DSP extensions. The Cortex-M4F sits at the top of the Cortex-M performance tier for microcontrollers, balancing deterministic interrupt response with signal-processing throughput. The SAM D51 family extends this core with Microchip peripheral IPs and a Dual-Panel Flash subsystem with ECC, positioning it above Cortex-M0+ SAM D20/D21 parts and below Cortex-M7 SAME70 parts in Microchip's portfolio. Key features of the ATSAMD51G18A-MF include up to 120 MHz core clock, 256 KB Flash with ECC, 128 KB SRAM with ECC, full-speed USB 2.0 with on-chip PHY, up to six SERCOM interfaces configurable as UART/SPI/I2C, a 12-bit ADC with up to 16 channels, two 12-bit DACs, and an I2S/PDM audio interface. The device also integrates a 16-bit timer/counter array, a Real-Time Clock, and a Cryptographic Acceleration Engine supporting AES, SHA, and Secure Boot. Architecturally, the ATSAMD51G18A leverages an Cortex-M4F core coupled to a multi-layer AHB/APB bus matrix, allowing simultaneous DMA-driven peripheral access and CPU execution. The on-chip FPU accelerates floating-point math used in sensor fusion, audio processing, and motor control loops, while the CCM (Crypto Accelerator Module) offloads AES/SHA from the core. Flash is Dual-Panel with Error Correction Code (ECC) for higher reliability in safety-critical firmware. Typical applications include USB Human Interface Devices, audio playback (USB headset, MP3 players), IoT edge nodes with secure firmware, motor control (BLDC, FOC), industrial HMI panels, and advanced sensor hubs. Designers also select it for portable test instruments and wearables that benefit from low power and DSP-class throughput. Designers should size the decoupling network (typically 100 nF + 4.7 µF bulk) close to each VDD pin, follow the 48-pin QFN land pattern (7x7 mm, 0.5 mm pitch), and use Atmel Studio / MPLAB X with the ASF or Harmony 3 framework to bring up the USB and SERCOM peripherals. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found on a single vendor page, providing an engineering-grade reference for procurement and bring-up decisions.

Cotización Contacto
ATSAMD51G18A-MFT - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAMD51G18A-MFT

ATSAMD51G18A-MFT - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD51G18A-MFT is a high-performance 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz, integrating 256 KB dual-panel Flash with ECC, 256 KB SRAM with ECC, and a USB 2.0 Full Speed interface, all housed in a 48-pin 7x7 mm QFN (VQFN/HVQCCN) package with an exposed thermal pad. The part suffix "MFT" denotes tape-and-reel packaging and the industrial extended temperature range of -40C to +125C. The integrated Floating Point Unit (FPU) and Microchip's Cortex-M4 DSP extension (single-precision MAC) accelerate closed-loop control, audio processing, and DSP front-ends while keeping deterministic interrupt response. An ARM Cortex-M4 microcontroller is a 32-bit core that combines deterministic real-time behavior with DSP extensions and an optional single-precision FPU. It sits in the hierarchy: Cortex-M4F core -> ARM Cortex-M family -> ARMv7-M architecture -> 32-bit embedded processor -> microcontroller. Compared to Cortex-M0/M0+ parts, the M4 adds hardware MAC, SIMD instructions and FPU, enabling floating-point control loops and DSP tasks that would otherwise require a Cortex-M7 or external DSP. Key features of the ATSAMD51G18A-MFT include: 120 MHz max core clock, 256 KB Flash with ECC and RWW support, 256 KB SRAM with ECC, a full-speed USB 2.0 device/host, up to 51 GPIO, a 12-bit 1 Msps ADC, two 12-bit DACs, and the SERCOM peripheral scheme (configurable UART/SPI/I2C/RS485). The Cortex-M4F DSP extension allows single-cycle MAC and SIMD, and the FPU handles single-precision floats. Power management integrates an on-chip DCDC buck converter and POR/BOD with brown-out reset. Technical depth: the dual-panel Flash architecture allows one bank to be updated while the other executes, enabling in-field firmware upgrade without downtime. ECC on both Flash and SRAM protects against bit-flips in harsh environments. Peripheral interconnect uses Microchip's AHB/APB matrix; SERCOM channels can be routed to multiple GPIO pins for layout flexibility. The on-chip DCDC supplies the core domain from the 3.3 V system rail, reducing external components. Typical applications include industrial sensor hubs, USB-CDC data loggers, motor-control subsystems (FOC and PID loops), audio effects processors, and IoT edge nodes with TLS offload. The combination of deterministic Cortex-M4F latency and rich analog (1 Msps ADC, 12-bit DAC) is well-suited to mixed-signal designs. Design consideration: place the exposed pad with at least 8 thermal vias (0.3 mm drill, 0.6 mm pitch) to a 1 oz inner copper pour to keep the junction below 100C at 120 MHz; bypassing the V2A/V2B DCDC pin pair requires the inductor plus low-ESR ceramic per the manufacturer reference schematic. This page consolidates verified distributor pricing, drop-in pin-compatible alternatives, and practical PCB-thermal design notes not found in a single location on the manufacturer datasheet.

Cotización Contacto
ATSAMD51G18A-MU - 120MHz ARM Cortex-M4F MCU 256KB Flash | Microchip
ATSAMD51G18A-MU

ATSAMD51G18A-MU - 120MHz ARM Cortex-M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAMD51G18A-MU is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit (FPU), 256 KB of Flash, and 128 KB of SRAM, housed in a 48-pin 7x7 mm VQFN package. The part operates from 1.71V to 3.63V and supports industrial temperature range -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one device. The ATSAMD51 belongs to the 32-bit microcontroller category, which sits within the broader embedded processor / semiconductor hierarchy. The SAM D51 family is positioned for high-performance Cortex-M4F applications requiring DSP instructions and floating-point math, contrasted with Cortex-M0+ parts such as the SAM D21 family that target lower-power, lower-cost designs. Key features include 256 KB Flash with ECC, 128 KB SRAM with ECC, a 12-bit 1 Msps ADC, two 12-bit DACs, USB 2.0 Full-Speed and High-Speed with on-chip PHY, a 10/100 Ethernet MAC, SD card host, I2S audio, up to six SERCOM serial channels, and a Cryptographic Accelerator (TRNG, AES, SHA). The Cortex-M4F core delivers 1.25 DMIPS/MHz and includes DSP extensions and a single-precision FPU for math-intensive tasks. Architecturally, the SAM D51 uses dual-panel Flash with Error Correction Code to improve reliability and support live firmware updates, and a tightly-coupled memory (TCM) interface for deterministic low-latency code execution. The Peripheral Event System allows peripherals to trigger each other without CPU intervention, freeing core bandwidth for application logic. Typical applications include industrial HMI panels, USB audio interfaces, IoT gateways, motor control with FOC algorithms, secure connected sensors, and graphical displays driven by the integrated Parallel Capture Interface or the I/O peripherals. When designing with this part, allocate adequate PCB area for the exposed pad on the bottom of the VQFN-48 package and connect it to a solid ground plane for thermal dissipation and electrical performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, with structured data optimized for engineers and AI-powered component search.

Cotización Contacto
ATSAMD51G18A-MU-EFP - 120MHz M4F MCU, 256KB Flash, USB | Microchip
ATSAMD51G18A-MU-EFP

ATSAMD51G18A-MU-EFP - 120MHz M4F MCU, 256KB Flash, USB | Microchip

The Microchip Technology ATSAMD51G18A-MU-EFP is a 32-bit ARM Cortex-M4F microcontroller with FPU, running up to 120 MHz with 256 KB dual-panel Flash (with ECC) and 128 KB SRAM (with ECC), housed in a 48-pin VQFN-48 (7x7 mm) package with extended Flash performance. The part integrates a high-speed USB 2.0 Full-Speed PHY, up to six SERCOM serial interfaces, a 12-bit 1 MSPS ADC, two 12-bit DACs, and up to 81 I/O lines. A microcontroller (MCU) is a single-chip processor that integrates CPU, memory, and peripherals; the ARM Cortex-M4F variant adds a single-precision Floating Point Unit and DSP extensions, enabling real-time DSP workloads on an MCU rather than a more expensive DSP chip. The SAM D51 family sits at the high-performance end of Microchip's Cortex-M4 lineup, targeting applications that previously required a Cortex-M7 or external DSP. Key features include 120 MHz CPU with FPU, 256 KB Flash in dual-panel configuration with ECC, 128 KB SRAM with ECC, integrated USB 2.0 Full-Speed PHY, a 12-bit 1 MSPS ADC with up to 16 channels, two 12-bit DAC outputs, six SERCOM (SERial COMmunication) modules that can be configured as UART, SPI, or I2C, an I2S interface for digital audio, six 16-bit timers, and a Cryptographic Accelerator supporting AES and SHA. The dual-panel Flash with ECC gives improved reliability versus single-panel Flash. The architecture combines a Cortex-M4F core from ARM with Microchip's peripheral set, fabricated on a low-power process that supports active, idle, standby, and backup sleep modes with RTC running from a 32.768 kHz crystal. The integrated USB PHY eliminates the need for an external USB transceiver, reducing BOM cost and PCB area for USB-enabled designs. Typical applications include USB human-interface devices (HID) such as keyboards and game controllers, audio processing with USB streaming, industrial sensor hubs, motor control, and IoT edge nodes with cryptography. The Cortex-M4F DSP extensions accelerate sensor-fusion algorithms and audio processing. When designing with this device, the integrated USB PHY requires careful PCB layout - follow the USB differential pair impedance (90 ohms differential) and length matching rules in the datasheet. Adequate decoupling is also critical: place 100 nF and 1 uF MLCC bypass capacitors near each VDD pin and one bulk capacitor on the AVDD rail to suppress ADC noise. This page synthesizes distributor pricing, same-package drop-in alternatives, application reference designs, and practical PCB design notes sourced from the manufacturer datasheet and DigiKey/Mouser product pages.

Cotización Contacto
ATSAMD51G18A-MUT-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAMD51G18A-MUT-EFP

ATSAMD51G18A-MUT-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD51G18A-MUT-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, operating up to 120 MHz with 256 KB of Flash and 128 KB of SRAM, housed in a 48-pin VQFN (7x7 mm) package. The integrated Floating Point Unit (FPU) and Cortex-M4 DSP extensions accelerate signal-processing workloads, while a 2 KB unified instruction/data cache reduces Flash wait states at the full 120 MHz clock. The Extended Flash Performance ("EFP") suffix designates an enhanced flash variant qualified for industrial temperature ranges. An ARM Cortex-M4 microcontroller is a 32-bit MCU core based on the ARMv7-M architecture that adds single-precision floating-point and SIMD DSP instructions to the standard Thumb-2 instruction set. It sits in the MCU taxonomy between Cortex-M0+ (lowest power) and Cortex-M7 (highest performance); Cortex-M4F specifically targets mixed control + DSP applications such as motor control, audio processing, and sensor fusion. The Cortex-M4 family is widely adopted across consumer, industrial, and IoT designs because it balances deterministic interrupt response, strong code density, and a mature toolchain (GCC, IAR, Keil, MPLAB X). Key features of the ATSAMD51G18A-MUT-EFP include 256 KB of dual-bank Flash with ECC, 128 KB SRAM with ECC, a 12-bit 1 MSPS ADC, two 12-bit DACs, a high-speed USB 2.0 Full-Speed PHY, up to six SERCOM serial interfaces (each configurable as UART/SPI/I2C), an I2S interface, an on-chip FPU, and a hardware cryptographic accelerator supporting AES and True Random Number Generator (TRNG). The integrated Peripheral Touch Controller (PTC) supports capacitive touch sensing, and the Event System enables inter-peripheral signaling without CPU intervention. A 32-bit Real-Time Clock (RTC) and a comprehensive sleep-wake controller with multiple low-power modes (Idle, Standby, Backup, Hibernate, Off) optimize battery life. Architecturally, the SAM D51 family combines an M-class Harvard bus with a multi-layer AHB/APB matrix, allowing simultaneous DMA-driven transfers on SERCOM, ADC, and DAC peripherals. The dual-panel flash supports live field updates without CPU stall, and ECC on both Flash and SRAM targets industrial and IEC 60730 Class B safety applications. The 120 MHz core plus hardware FPU delivers 150 DMIPS and 273 CoreMark scores, ranking the part among the highest-performance Cortex-M4F MCUs available. Typical applications include industrial sensor hubs, USB Human Interface Devices (HID), audio playback devices with I2S codecs, low-latency motor-control loops, IoT edge nodes with secure boot, capacitive touch user interfaces, and battery-powered wearables. Designers often pair the device with external SPI NOR Flash for data logging or with a crypto-authentication IC for secure firmware updates. When designing with this MCU, allocate the integrated PTC channels carefully because they share pins with GPIO and ADC inputs; a pinout conflict between touch sensors and analog measurements is a common prototype-stage pitfall. Also ensure that VDDIO and VDDCORE decoupling follow the SAM D51 datasheet reference layout - poor decoupling is the most frequent cause of USB enumeration failure and brown-out resets at the 120 MHz operating point. This page synthesizes distributor stock levels, drop-in alternatives, application examples, and practical design notes not collected in any single source - including a side-by-side pin-compatibility matrix for engineers evaluating SAM D51 vs SAM D21 or competing STM32 families.

Cotización Contacto
ATSAMD51G19A-MF - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAMD51G19A-MF

ATSAMD51G19A-MF - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAMD51G19A-MF is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, delivering up to 120 MHz CPU performance with hardware floating-point unit, packaged in a 48-pin 7x7 mm QFN. It integrates 512 KB of dual-panel Flash with ECC and 192 KB of SRAM, addressing high-performance general-purpose designs that need more headroom than Cortex-M0+ parts without moving to Cortex-M7. A microcontroller (MCU) is a single-chip computer that combines a processor core, program and data memory, and a rich set of on-chip peripherals. The Cortex-M4F core specifically adds DSP extensions and an FPU so the SAM D51 can execute single-precision floating-point operations in hardware, accelerating signal-processing and control loops. Microcontrollers sit below microprocessors in the embedded hierarchy (MCU -> 32-bit MCU -> ARM Cortex-M -> Cortex-M4F -> SAM D51 family), and above simple digital logic ICs, occupying the "compute + control" tier of the system. The SAM D51 series in particular targets connected, low-power, and human-machine-interface applications. Key features include a Cortex-M4F core with FPU at 120 MHz, 512 KB dual-bank Flash with error-correction, up to 192 KB SRAM with ECC, a 12-bit 1 MSPS ADC with up to 16 channels, a 12-bit 1 MSPS DAC, USB 2.0 Full-Speed with integrated PHY, up to 6 SERCOM serial interfaces, I2S, CAN-FD, and an on-chip 32 kHz RTC plus multiple timers. The 48-QFN package exposes 38 GPIO, multiple analog and digital peripherals, and operates from 1.71 V to 3.6 V with industrial -40C to +125C temperature range. Architecturally, the SAM D51 uses Microchip's event system, peripheral touch controller, and configurable SERCOM blocks so that one peripheral can serve UART, SPI, I2C, or LIN on the fly. The dual-panel Flash allows live firmware updates (in-place + simultaneous writes) without external memory, while ECC protects against bit flips in safety-relevant code paths. The integrated USB PHY removes external components, saving BOM cost in connected designs. Together these features let engineers add rich peripherals and connectivity to battery-powered or industrial devices without sacrificing determinism. Typical applications include USB peripherals (HID, CDC, MIDI), industrial sensor hubs, motor and lighting controllers, IoT edge nodes, low-power audio front-ends, and HMI panels with touch. Designers frequently pair the SAM D51 with QSPI NOR flash for larger buffers, Ethernet controllers for wired connectivity, and MEMS sensors over I2C/SPI for environmental sensing. When designing with the ATSAMD51G19A-MF, plan the boot sequence: the part supports secure boot, dual-bank OTA via flash overwrite, and configurable brown-out behavior. Use Atmel/Microchip Studio or MPLAB X with the START project generator to pick the right clock tree and pin-mux configuration before committing to PCB layout. Ensure decoupling is placed close to all VDD/VDDIO pins and that the exposed pad of the QFN-48 is tied to a solid ground copper pour for thermal dissipation. This page synthesizes distributor pricing, drop-in compatible alternatives from the SAM D51 and SAME51 families, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and qualifying the ATSAMD51G19A-MF.

Cotización Contacto
ATSAMD51G19A-MFT - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip
ATSAMD51G19A-MFT

ATSAMD51G19A-MFT - 120MHz Cortex-M4F MCU, 512KB Flash | Microchip

The Microchip Technology ATSAMD51G19A-MFT is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, running up to 120 MHz with single-precision floating point and a full DSP instruction set, packaged in a 48-pin VQFN (7x7 mm) and qualified for the extended industrial temperature range. It integrates 512 KB of dual-panel Flash with ECC and up to 192 KB of SRAM, plus a high-speed USB 2.0 Full-Speed device/host interface and a sophisticated SERCOM peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals (timers, ADC, communication controllers, GPIO) into one package. The ARM Cortex-M family is the dominant 32-bit MCU architecture for embedded systems, and Cortex-M4F specifically adds hardware single-precision floating point and DSP extensions, making it a step up from Cortex-M0/M3 parts in signal-processing capability. The SAM D51 line sits in Microchip's high-performance tier, between the mainstream SAM D20/D21 and the more capable SAME70/SAMS70 families. Key features of the ATSAMD51G19A-MFT include six SERCOM modules (each configurable as UART/SPI/I2C), a 12-bit 1 Msps ADC with up to 16 channels, a 10-bit 300 ksps DAC, multiple 16-bit timers, an I2S/SSC audio interface, a CAN-FD controller, and a QSPI interface for external memory expansion. The device also integrates a full-speed USB 2.0 transceiver supporting both device and host modes, eliminating the need for an external PHY in most designs. On the architecture side, the ATSAMD51G19A-MFT uses Microchip's event system, a peripheral-to-peripheral interconnect that lets timers, DMA, and GPIO trigger each other without CPU intervention - useful for low-latency, deterministic real-time designs. The dual-panel Flash with ECC and the banked SRAM layout support firmware updates in the field while executing from the other bank, simplifying bootloader design for IoT and remote-update products. Typical applications include USB human-interface devices (keyboards, mice, audio class peripherals), industrial sensor hubs, motor control boards, IoT gateways, and audio-processing subsystems. The combination of USB, CAN-FD, and 1 Msps ADC makes it a strong fit for industrial instrumentation where a single MCU can handle both communications and analog front-end work. When laying out a board, dedicate continuous copper under the exposed pad to the same ground plane, place the 32.768 kHz and 12 MHz crystals within 5 mm of their pins, and keep the VDDIO and VDDCORE decoupling (100 nF + 1 uF per pin) within 2 mm of each supply pin. USB DP/DM traces must be 90 ohm differential and length-matched. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, giving a complete procurement and engineering decision view in one place.

Cotización Contacto
ATSAMD51G19A-MU - 120MHz Cortex-M4F MCU 512KB Flash | Microchip
ATSAMD51G19A-MU

ATSAMD51G19A-MU - 120MHz Cortex-M4F MCU 512KB Flash | Microchip

The Microchip Technology ATSAMD51G19A-MU is a high-performance 32-bit ARM Cortex-M4F microcontroller with Floating Point Unit, running up to 120 MHz, and packaged in a 48-pin QFN (7x7 mm) with exposed thermal pad. The SAM D51 variant integrates 512 KB of dual-panel Flash with ECC and 192 KB of SRAM, targeting general-purpose embedded designs that require DSP-class signal processing and rich connectivity. An ARM Cortex-M4F microcontroller is a 32-bit processor core built on the ARMv7-M architecture, featuring a hardware single-precision Floating Point Unit (FPU) compliant with IEEE 754, a Memory Protection Unit (MPU), and DSP extensions. Within the broader taxonomy, the ATSAMD51G19A-MU is an MCU, a sub-category of microcontrollers, which falls under Embedded Processors and Controllers in the Integrated Circuits family. The Cortex-M4F core enables efficient execution of complex math, sensor-fusion algorithms, and audio processing without external DSP hardware. Key features include an integrated FPU for floating-point math, 512 KB of program storage, 192 KB SRAM, a Cryptographic Accelerator for AES, True Random Number Generator (TRNG), Public Key Cryptography support, and a high-speed Multi-bit ECC-protected Flash. The device provides advanced connectivity with a 12-bit 1 Msps ADC, 12-bit DAC, analog comparators, multiple SERCOM interfaces configurable as UART/SPI/I2C, and a high-speed USB 2.0 interface. The 48-QFN package features a thermal pad for improved thermal dissipation. Technically, the ATSAMD51G19A-MU runs at a maximum CPU clock of 120 MHz delivering 150 DMIPS and 273 CoreMark performance. The dual-panel Flash architecture supports simultaneous read-while-write operations, enabling live firmware updates without halting execution. Power management includes multiple low-power Sleep modes and an integrated buck converter for core supply, reducing overall system power consumption. The Event System and Peripheral Touch Controller (PTC) support capacitive touch sensing directly on hardware pins. Typical applications include IoT edge nodes, industrial control and HMI panels, audio processing devices with USB audio class support, smart sensor hubs with on-device sensor fusion, motor control with FOC algorithms, and wearable health monitoring devices. The cryptographic accelerator and TRNG also make it suitable for secure connected devices requiring hardware-rooted identity. When designing with this MCU, allocate sufficient decoupling capacitance near each supply pin and ensure the thermal pad is soldered to a properly sized copper pour for optimal heat dissipation. Configure the GCLK generators carefully to avoid peripheral clock conflicts, and validate that the chosen FPU code paths are properly compiled with hardware floating-point flags. This page synthesizes distributor pricing, drop-in same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone, providing a faster cross-reference for engineers selecting Cortex-M4F microcontrollers in compact 48-pin QFN packages.

Cotización Contacto
ATSAMD51G19A-MU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash, 48-VQFN
ATSAMD51G19A-MU-EFP

ATSAMD51G19A-MU-EFP - 120MHz Cortex-M4F MCU, 512KB Flash, 48-VQFN

The Microchip Technology ATSAMD51G19A-MU-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, running up to 120 MHz with 512 KB Flash and 192 KB SRAM, housed in a 48-pin VQFN (7x7 mm) package with extended Flash performance. The -EFP suffix designates Microchip's extended Flash performance and -40C to +85C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripherals into one IC. Within the broader semiconductor hierarchy, MCUs sit between general-purpose microprocessors (MPUs) and digital signal controllers (DSCs); the SAM D51 specifically belongs to the Cortex-M4F class of MCUs that pair a Cortex-M4 core with a single-precision Floating Point Unit (FPU) and DSP extensions. This places it above Cortex-M0+/M3 devices in compute capability while remaining lower-power than Cortex-M7 parts. Key features include the 120 MHz Cortex-M4F core with FPU, 512 KB dual-panel Flash with ECC, 192 KB SRAM with ECC, a full-speed USB 2.0 interface with on-chip PHY, up to six SERCOM serial interfaces, a 12-bit 1 MSPS ADC, two 12-bit DACs, and a QSPI/SPI interface for external memory. The integrated FPU and DSP instructions enable efficient floating-point math for sensor-fusion and audio workloads without CPU stalls. A 32-channel Event System, 16-bit timers, and a Cryptographic Accelerator (TRNG + AES) round out the on-chip resources. Typical applications include IoT edge nodes, USB audio devices, industrial sensor hubs, HMI panels, and motor-control subsystems. Industrial-grade USB HID/CDC peripherals and connected sensor platforms benefit from the SAM D51's USB PHY, multiple SERCOM instances, and AES/TRNG hardware security. With extended Flash performance the -EFP variant guarantees higher Flash endurance and faster wait-state behaviour for read-while-write firmware updates. When designing with this MCU, place the on-chip decoupling capacitor array within 3 mm of the VDD pins and route the USB DP/DM pair as a 90-ohm differential. The boot loader is factory-programmed into a dedicated ROM region, so user Flash starts at 0x00000000 for dual-bank A and the BOOTPROT and NVMCTRL fuses should be locked before production. This page synthesises distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
ATSAMD51J18A-AF - SAM D51 Cortex-M4F MCU 120MHz 256KB | Microchip
ATSAMD51J18A-AF

ATSAMD51J18A-AF - SAM D51 Cortex-M4F MCU 120MHz 256KB | Microchip

The Microchip ATSAMD51J18A-AF is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, running up to 120 MHz with single-precision Floating Point Unit (FPU), 256 KB Flash and up to 128 KB SRAM in a 64-pin TQFP (10x10 mm) package. The device integrates a full-speed USB 2.0 interface, a high-speed 12-bit ADC, multiple SERCOM peripherals, I2S, and SDHC support, addressing high-performance embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of peripherals such as timers, communication controllers, and analog blocks. The Cortex-M4F sits within the broader taxonomy of ARM Cortex-M cores (M0/M0+ -> M3 -> M4/M4F -> M7) and is positioned for DSP-class workloads while retaining deterministic interrupt behaviour and low-power Sleep modes. The SAM D51 family extends this core with Microchip's peripheral set, dual-panel Flash with ECC, and a dedicated Cortex-M4 core with FPU for floating-point acceleration. Key features of the ATSAMD51J18A-AF include: up to 120 MHz core clock with single-precision FPU and DSP instructions, 256 KB dual-panel Flash with error correction, up to 128 KB SRAM, full-speed USB 2.0 device/host with on-the-go capability, a 12-bit 1 MSPS ADC with up to 16 channels, multiple SERCOM modules configurable as UART/SPI/I2C, I2S for digital audio, SDHC for memory cards, and an extended industrial operating temperature range. The 64-pin TQFP package balances I/O count with hand-solder-friendly pitch, simplifying prototype bring-up. The architecture combines a Cortex-M4F core with a multi-layer bus matrix (AHB/APB) that allows simultaneous DMA-driven peripheral access and CPU execution. Hardware cryptographic acceleration (AES, True Random Number Generator), a high-precision internal 48 MHz DFLL, and an Event System for inter-peripheral signalling reduce CPU overhead and enable deterministic real-time response. Compared with Cortex-M0+ parts in the SAM D20/D21 family, the D51 delivers roughly 4x compute performance and substantially richer analog and connectivity resources. Typical applications include industrial HMI panels, USB peripherals such as HID and CDC devices, audio playback stages using I2S codecs, smart sensor hubs, and low-power IoT edge nodes. The integrated FPU simplifies control-loop math and DSP-style filtering on a single MCU without an external DSP. When designing with the ATSAMD51J18A-AF, ensure the 64-pin TQFP land pattern is allocated correctly and that decoupling follows Microchip's recommended 100 nF + bulk capacitor scheme near each supply pin. For USB applications the DP/DN lines require 90 ohm differential routing and an ESD array; for I2S audio, the MCLK-to-LRCLK ratio must match the codec's requirements and jitter on MCLK should be kept below the codec's specification.

Cotización Contacto
ATSAMD51J18A-AU - 120MHz Cortex-M4F MCU 256KB Flash 64-TQFP | Microchip
ATSAMD51J18A-AU

ATSAMD51J18A-AU - 120MHz Cortex-M4F MCU 256KB Flash 64-TQFP | Microchip

The Microchip Technology ATSAMD51J18A-AU is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with single-precision Floating Point Unit, delivering 256 KB of flash and up to 256 KB SRAM in a 64-pin TQFP (10x10 mm) package. It belongs to the SAM D5x/E5x family and integrates a rich peripheral set including a 12-bit ADC, 12-bit DAC, SERCOM, I2S, USB, and an on-chip PTC touch controller. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (flash), data memory (SRAM), and integrated peripherals. The Cortex-M4F core implements the ARMv7-M architecture with hardware FPU and DSP extensions, enabling deterministic real-time control and floating-point signal processing. The ATSAMD51J18A-AU is engineered for general-purpose embedded applications that need DSP performance and analog integration on a single die. Key features include up to 120 MHz CPU clock with 2.46 CoreMark/MHz, hardware FPU, 256 KB flash with ECC, 256 KB SRAM with ECC, a 12-bit 1-MSPS ADC, 12-bit DAC, SERCOM (configurable UART/SPI/I2C), USB 2.0 full-speed with on-chip PHY, I2S, and a Peripheral Touch Controller (PTC) for capacitive touch sensing. The device also includes a 32-bit RTC, multiple timer/counters, and an Event System for hardware-triggered peripheral interactions without CPU involvement. Architecturally, the ATSAMD51J18A-AU uses Microchip's SAM D5x bus matrix with separate AHB/APB bridges, enabling concurrent peripheral DMA and CPU execution. The Event System routes peripheral triggers across the chip in zero CPU cycles, and the DMA controller supports scatter-gather transfers for high-throughput sensor streams. The integrated FPU eliminates software floating-point emulation for signal-processing tasks such as audio decoders, motor control loops, and sensor fusion. Typical applications include industrial control panels with capacitive touch UI, smart energy metering, USB-connected data loggers, audio effect processors, low-power IoT gateways, and BLDC/PMSM motor controllers using field-oriented control. The Cortex-M4F DSP and FPU accelerate audio decoding and motor math by 10-100x compared to M0+ devices. When designing with this hardware, plan the 64-pin TQFP layout carefully because the larger flash variants share the same package footprint. The -AU suffix indicates the automotive (125C) operating temperature grade, making the part suitable for harsh industrial and automotive under-hood environments. Refer to the manufacturer datasheet for full peripheral mapping and clock tree details. This page synthesizes distributor pricing from DigiKey, Mouser, LCSC and Heisener, drop-in same-family alternates, design notes and FAQs not bundled in the manufacturer datasheet, including answers to common production-engineering questions about procurement, lifetime, and pin compatibility.

Cotización Contacto
ATSAMD51J18A-AU-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAMD51J18A-AU-EFP

ATSAMD51J18A-AU-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD51J18A-AU-EFP is a 32-bit ARM Cortex-M4F microcontroller running up to 120 MHz with 256 KB Flash and 128 KB SRAM in a 64-pin TQFP (10x10 mm) package. It is part of the SAM D51 family targeted at general-purpose and high-performance embedded applications requiring FPU, DSP, and rich connectivity peripherals. This variant includes a USB 2.0 Full-Speed interface with integrated PHY, a 12-bit ADC up to 1 Msps, DAC, SERCOM, and I2S, making it suitable for sensor fusion, audio, and IoT edge devices. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for program code and SRAM for data), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. Within the broader taxonomy, the ATSAMD51J18A sits in the hierarchy: microcontroller -> 32-bit MCU -> ARM Cortex-M class -> Cortex-M4F (with Floating Point Unit and DSP extensions) -> general-purpose MCU. The FPU accelerates single-precision floating-point math, while DSP extensions enable MAC instructions and SIMD-style operations, both critical for sensor-fusion and signal-processing workloads at low power. Key specifications include 256 KB Flash with ECC, 128 KB SRAM with ECC, 120 MHz Cortex-M4F core, 12-bit 1 Msps ADC with up to 16 channels, 10-bit 350 ksps DAC, six SERCOM configurable serial interfaces (UART/SPI/I2C), USB 2.0 Full-Speed with on-chip PHY, I2S, and an Event System for inter-peripheral signaling. Operating voltage spans 1.71 V to 3.63 V, with a -40C to +85C industrial temperature range, making it well-suited for harsh-environment designs. Architecturally, the ATSAMD51J18A uses a dual-bank Flash with EEPROM emulation support and a 4 KB cache that masks Flash wait-states to sustain single-cycle execution at 120 MHz. The peripheral event system and DMAC offload CPU overhead, allowing deterministic real-time response for motor control, audio decoding, or multi-protocol sensor hubs. Typical applications include industrial IoT gateways, USB-C HID peripherals, portable medical instrumentation, audio effects processors, and low-power robotics controllers. The combination of DSP instructions, FPU, USB, and ample analog peripherals lets a single MCU replace an MPU-plus-external-DSP architecture in cost-sensitive designs. Designers should allocate decoupling capacitors near each VDD pin (100 nF plus bulk 4.7 uF) and follow Microchip's SAM D51 hardware design checklist for crystal layout. For lowest active power, use the SleepWalking mode, and configure the ADC with internal reference and proper acquisition timing to avoid channel crosstalk. This page combines datasheet specifications, distributor pricing, drop-in alternatives, and practical design notes not collated on the manufacturer datasheet, giving engineers a single reference for evaluation and BOM decisions.

Cotización Contacto
ATSAMD51J18A-AUT - 120MHz Cortex-M4F MCU 256KB Flash | Microchip
ATSAMD51J18A-AUT

ATSAMD51J18A-AUT - 120MHz Cortex-M4F MCU 256KB Flash | Microchip

The Microchip Technology ATSAMD51J18A-AUT is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, running up to 120 MHz with an integrated Floating Point Unit, 256 KB of Flash, and housed in a 64-pin TQFP (10x10 mm) package. Operating from 1.71V to 3.6V with a maximum CPU clock of 120 MHz, it integrates 256 KB Flash with ECC and up to 128 KB SRAM, plus a rich peripheral set including SERCOM, USB, CAN-FD, and a 12-bit ADC. The 'AUT' suffix indicates automotive-grade qualification suitable for -40C to +85C operation. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, communication interfaces, and analog blocks. The ARM Cortex-M4F architecture belongs to the ARM Cortex-M family, designed for deterministic real-time embedded applications; the 'F' denotes an integrated single-precision Floating Point Unit (FPU). MCUs sit within the broader category of embedded processors, sitting below application processors in computational complexity but offering lower power, deterministic interrupt response, and a smaller footprint ideal for IoT, motor control, and HMI designs. Key features include a 120 MHz Cortex-M4F core with FPU and DSP extensions, 256 KB dual-panel Flash with ECC, up to 128 KB SRAM with ECC, six SERCOM configurable serial interfaces supporting I2C/SPI/UART, a high-speed USB 2.0 Full-Speed device/host port, one CAN-FD controller, a 12-bit 1 MSPS ADC, two 12-bit DACs, and a Real-Time Clock (RTC). The device also integrates an Event System, SleepWalking peripherals for low-power operation, and a Self-Programming Flash controller for in-field OTA updates. The SAM D51 architecture combines deterministic Cortex-M4F processing with Microchip's extensive SmartConnect peripheral IP, enabling flexible pin-mapping through SERCOM multiplexing. The dual-panel Flash with ECC supports robust code execution in noisy automotive and industrial environments, while the FPU accelerates floating-point math for sensor fusion, motor control, and DSP audio workloads without burdening the CPU. Typical applications include automotive body electronics and HMI, industrial IoT sensor nodes, USB human-interface devices (keyboards, mice, touch panels), CAN-FD nodes, motor control with FPU-based field-oriented control, and portable consumer devices. The automotive-grade temperature range and CAN-FD support make this part especially attractive for vehicle gateway and infotainment subsystems. When designing with this device, plan the SERCOM multiplexing carefully because six SERCOM channels can each be mapped to multiple pin sets; this flexibility simplifies PCB layout but requires reference to the device pinout table to avoid conflicts. Provide a clean 3.3V LDO with adequate decoupling (100 nF + bulk) near the VDD pins to support core and I/O switching transients. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
ATSAMD51J18A-AUT-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
ATSAMD51J18A-AUT-EFP

ATSAMD51J18A-AUT-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip

The Microchip Technology ATSAMD51J18A-AUT-EFP is a 32-bit ARM Cortex-M4F microcontroller from the SAM D51 family, delivering 120 MHz CPU performance with single-precision Floating Point Unit (FPU), 256 KB of Dual-Panel Flash with ECC, and 256 KB SRAM with ECC in a 64-pin TQFP (10x10 mm) package. The -EFP suffix denotes Extended Flash Performance, an enhanced flash variant qualified for the automotive temperature grade (-40C to +125C) and supplied on Tape & Reel. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code, SRAM for data), and programmable peripherals. The SAM D51 line belongs to the broader 32-bit ARM Cortex-M family, which dominates modern embedded designs due to its deterministic interrupt handling, low power consumption, and the vast ecosystem of ARM toolchains. Within that family the Cortex-M4F adds hardware single-precision floating point and DSP extensions, positioning the M4F between the smaller Cortex-M0/M3 and the larger Cortex-M7. The SAM D51 further extends the family with high-speed USB, an integrated AES crypto engine, and up to 1 MB flash in higher-order derivatives - making it suitable for industrial IoT, audio processing, and human-machine interface (HMI) applications. Key features include the Cortex-M4F core at 120 MHz with FPU and DSP instructions, 256 KB Dual-Panel Flash supporting live firmware updates, 256 KB SRAM, a 12-bit 1 MSPS ADC, two 12-bit DACs, SERCOM configurable serial peripherals (UART/SPI/I2C), Full-Speed and Hi-Speed USB 2.0 with integrated PHY, and an Event System for hardware-triggered peripheral actions without CPU intervention. The -EFP variant qualifies the part for extended flash performance across the full -40C to +125C automotive-grade temperature range. Architecturally, the device pairs the ARM Cortex-M4F core with a Multi-Layer Bus Matrix that allows simultaneous DMA, USB, and Ethernet traffic without CPU stalls, plus a Peripheral Touch Controller (PTC) supporting capacitive touch sensing. An integrated AES-256 hardware block accelerates secure boot and encrypted communications. Typical applications include industrial IoT gateways, USB-C Human Interface Devices (HID), automotive body and infotainment controllers, audio DSP front-ends, and low-power wireless sensor nodes. The wide operating voltage (1.71V-3.63V) simplifies designs powered by Li-Ion or 3.3V regulated rails. Designers should provision a 1 uF + 100 nF decoupling network near each VDD pin and route the D+/D- USB traces as a 90 ohm differential pair. The Dual-Panel Flash enables safe over-the-air (OTA) firmware upgrades by allowing one panel to receive a new image while the other continues running the current application. This page synthesizes distributor stock and pricing, automotive-grade drop-in alternatives from the same SAM D51 family, and practical design notes not consolidated in the manufacturer datasheet.

Cotización Contacto