5M570ZM100A5N - MAX V 440 Macrocells CPLD, 100-ball MBGA, 1.8V | Intel
N.º de pieza: 5M570ZM100A5N ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $7.5 | $7,50 |
| 10 | $6.95 | $69,50 |
| 100 | $6.1 | $610,00 |
| 500 | $5.4 | $2.700,00 |
| 1.000 | $4.85 | $4.850,00 |
5M570ZM100A5N Descripción general
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the digital hierarchy between simple PLDs/glue logic and high-density FPGAs. It typically contains multiple macrocell-based logic blocks connected via a programmable interconnect fabric (PIA), providing fast, deterministic pin-to-pin propagation delays for combinatorial and registered logic, bus interfacing, and power-up state control. CPLDs retain configuration in on-chip flash, requiring no external boot PROM.
Key features of the 5M570ZM100A5N include 440 macrocells (equivalent to ~570 logic elements), 74 user I/Os, 1.8 V core VCCINT, user I/O bank support for 1.5 V / 1.8 V / 2.5 V / 3.3 V LVCMOS/LVTTL interfaces via MultiVolt I/O, an internal oscillator, in-system programmability via JTAG, and an instant-on non-volatile architecture. The device targets glue-logic, interface bridging, power-up sequencing, and control-plane tasks where deterministic timing and zero-boot-time behavior are required.
The 5M570ZM100A5N uses a flash-based, look-up-table macrocell architecture with eight logic array blocks (LABs), each containing 16 macrocells. The JTAG/IEEE 1149.1 boundary-scan interface supports in-system programming and board-level test, while the on-chip oscillator removes the need for an external clock source in many designs. MultiVolt I/O banks allow direct interfacing with 1.5 V, 1.8 V, 2.5 V, and 3.3 V logic without level shifters.
Typical applications include bus interface bridging (e.g., I2C-to-SPI, RGB-to-LVDS), power-up and power-down sequencing for processors/ASICs/FPGAs, I/O expansion and reset distribution, control-plane logic in industrial controllers, and general board-level glue logic in communications and consumer equipment. The combination of low power, instant-on, and high I/O count makes it well suited as a companion device to higher-density Cyclone or Stratix FPGAs.
When designing with the 5M570ZM100A5N, observe the VCCINT decoupling guidelines in the MAX V device handbook (place 0.1 uF and bulk capacitors close to the supply balls), and use the Quartus II / Quartus Prime MAX V device library for synthesis, fitting, and timing analysis. Note that this MBGA-100 package is not socket-friendly - PCB assembly requires BGA reflow and X-ray or AOI inspection.
Alternativas directas para 5M570ZM100A5N — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con 5M570ZM100A5N (mismo factor de forma y huella) — difiere en Package, Programming Interface, Operating Temperature, Configuration Memory, Maximum Internal Frequency.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
5M570ZM100C4N
✅ Sustitución directa✓ En stock
$8.74 / unidad
Ver hoja de datos →5M570ZM100I5N
✅ Sustitución directa✓ En stock
$15.34 / unidad
Ver hoja de datos →5M570ZM100C5N
✅ Sustitución directa✓ En stock
$6.8 / unidad
Ver hoja de datos →5M240ZM100C5N
✅ Sustitución directa✓ En stock
$7.4 / unidad
Ver hoja de datos →5M160ZM100C5N
✅ Sustitución directa✓ En stock
$4.35 / unidad
Ver hoja de datos →5M570ZM100A5N Valores máximos y características eléctricas
| Family | MAX V |
| Macrocells | 440 |
| User I/Os | 74 |
| Logic Elements | 570 |
| Logic Array Blocks (LABs) | 8 (16 macrocells per LAB) |
| Maximum Internal Frequency | 118.3 MHz |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Voltage (VCCIO) | 1.5 V / 1.8 V / 2.5 V / 3.3 V (MultiVolt) |
| Standby Current | 27 uA (typical) |
| Programming Interface | JTAG (IEEE 1149.1) / ISP |
| On-chip Oscillator | Yes |
| Non-volatile Configuration | Flash (instant-on) |
| Encapsulado | 100-ball Micro BGA (MBGA, 6x6 mm) |
| Operating Temperature Grade | Industrial |
| Estado RoHS | Compliant |
| Lead-Free | Yes |
| Tipo de montaje | Surface Mount (BGA) |
Guía de configuración de pines de 5M570ZM100A5N 100-ball micro bga (mbga, 6x6 mm)
Configuración de pines para 5M570ZM100A5N (encapsulado 100-ball micro bga (mbga, 6x6 mm)). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para 5M570ZM100A5N.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
5M570ZM100A5N es adecuado para 6 aplicacións: FPGA/ASIC Power-Up Sequencing Controller, I2C / SPI / UART Bus Bridge, Industrial Control-Plane Glue Logic, Display Interface Bridge (RGB-to-LVDS, MIPI Side-band), Board-Level Reset and Clock Distribution, Consumer Device Interface Expansion.
FPGA/ASIC Power-Up Sequencing Controller
The 5M570ZM100A5N is an excellent power-up sequencer for systems with multi-rail processors, ASICs, or FPGAs. Its instant-on flash configuration means all 74 I/Os drive to a known state at t=0, and the 1.8 V core with MultiVolt I/O banks (1.5/1.8/2.5/3.3 V) directly interfaces with each rail's enable pin. With 440 macrocells the device can orchestrate sequencing for 10+ rails, monitor POWER_GOOD feedback, and assert reset - all while drawing only 27 uA standby. Use it as a companion device to a Cyclone V, Stratix, or any external ASIC.
Recomendado
I2C / SPI / UART Bus Bridge
The 5M570ZM100A5N's 440 macrocells and 74 I/Os are well suited to implementing custom bus bridges between processors and peripherals. A typical bridge uses four I/O pins per I2C/SPI channel plus a small state machine, allowing the CPLD to translate between I2C and SPI, multiplex UARTs, or add parity/handshake logic. The 118.3 MHz internal frequency supports bus rates up to about 30 MHz, covering most legacy and modern embedded protocols. Non-volatile configuration means the bridge is live immediately on power-up.
Recomendado
Industrial Control-Plane Glue Logic
Industrial PLCs, motor controllers, and factory-automation boards need glue logic for level translation, reset distribution, watchdog supervision, and address decoding. The 5M570ZM100A5N's industrial temperature range, low 27 uA standby, and 74 I/Os let one CPLD replace a handful of 74-series TTL chips. The 100-ball MBGA (6x6 mm) fits inside small DIN-rail and machine-vision PCBs. Combined with its deterministic tPD, it adds predictable timing margins to ASIL-rated industrial designs.
Recomendado
Display Interface Bridge (RGB-to-LVDS, MIPI Side-band)
LCD/panel adapters often need RGB-to-LVDS bridging, pixel-clock multiplication, or side-band signal generation between a processor and a TFT panel. The 5M570ZM100A5N can generate side-band signals (backlight enable, PWM dimming, H/V sync retiming) and perform minor pixel remapping, freeing the host processor from timing-critical tasks. 74 I/Os are enough for 18/24-bit RGB plus control and backlight signals. MultiVolt I/O banks support both 1.8 V processor logic and 3.3 V panel signaling.
Recomendado
Board-Level Reset and Clock Distribution
Modern SoCs and FPGAs require coordinated resets across multiple rails and a low-jitter clock tree. The 5M570ZM100A5N can buffer and fan out clocks using its on-chip PLL-free oscillator plus external clock inputs, while its 74 I/Os distribute individually-tailored reset pulses to different subsystems. Deterministic tPD ensures reset skew stays within datasheet limits - critical for JTAG-chain integrity and PCIe/SERDES link-up.
Recomendado
Consumer Device Interface Expansion
Set-top boxes, smart-home hubs, and IoT gateways often lack enough GPIO or specialized peripherals for keypad scanning, IR receive/transmit, or LED matrix driving. The 5M570ZM100A5N's 74 I/Os and 440 macrocells can scan an 8x8 keypad, generate IR carrier signals, and Charlieplex an LED array - all without burdening the host CPU. The MBGA-100 (6x6 mm) fits in slim enclosures, and the 1.8 V core keeps standby power at 27 uA.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para 5M570ZM100A5N — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | 5M570ZM100C4N | 5M570ZM100I5N | 5M240ZM100C5N | 5M160ZM100C5N |
|---|---|---|---|---|---|
| Package | MBGA-100 (6x6 mm) | MBGA-100 - same | MBGA-100 - same | MBGA-100 - same | MBGA-100 - same |
| Brand | Intel | Intel | Intel | Intel | Intel |
| Family | MAX V | MAX V | MAX V | MAX V | MAX V |
| Macrocells | 440 | 440 | 440 | 240 | 160 |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Temperature Grade | Industrial (A) | Commercial (C) | Industrial (I) | Commercial (C) | Commercial (C) |
Diferenciadores clave
- Highest macrocell count in the MBGA-100 package family (frente a 5M240ZM100C5N)
- Industrial temperature grade for harsh environments (frente a 5M570ZM100C4N)
- Compact MBGA-100 vs larger FBGA packages (frente a 5M570ZF256C5N)
Notas de diseño
Place 0.1 uF decoupling capacitors as close as possible to every VCCINT and VCCIO ball, plus bulk capacitors on each supply rail. For the 100-ball MBGA package, fan-out the balls on the top layer to vias-in-pad or near-pad, then route power on inner layers. Avoid running high-speed signals under the BGA unless on a dedicated ground-plane inner layer.
The 118.3 MHz internal clock and MultiVolt I/O banks can generate edge rates fast enough to cause reflections on unterminated traces. For LVCMOS 3.3 V outputs driving cables or long PCB traces (>50 mm), add a 33 ohm series damping resistor near the CPLD. For LVDS or higher-speed interfaces, route as 100 ohm differential pairs with matched length.
Do not assume all I/O banks are independent - VCCIO must be powered before or simultaneously with VCCINT, or the I/O pins enter an indeterminate state that can latch-up internal ESD structures. Always tie JTAG TCK low during power-up to keep the device in bypass mode if the JTAG chain is shared with another device that boots later.
Información de cumplimiento
RoHS and lead-free per Intel / Altera product page. Not AEC-Q100 qualified (industrial grade only - not automotive). REACH and conflict-mineral statements per Intel PSG compliance disclosures.
