74HC245D - Octal 3-State Bus Transceiver | Logic IC
N.º de pieza: 74HC245D ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0.1011 | $0,10 |
| 10 | $0.1011 | $1,01 |
| 100 | $0.1011 | $10,11 |
| 500 | $0.1011 | $50,55 |
| 1.000 | $0.1011 | $101,10 |
74HC245D Descripción general
A bus transceiver is a bidirectional interface IC that connects two logic buses, allows data to move in a selected direction, and places its outputs into a high-impedance state when disabled. The 74HC family belongs to high-speed CMOS logic and combines low power dissipation with performance comparable to LSTTL, making it useful in digital systems, memory interfaces, peripheral buses, and embedded control equipment.
The verified product description identifies the device as an octal bus transceiver with three-state outputs. The DIR input determines the direction of data flow between the A and B buses, while the active-low output-enable input provides bus isolation. Because the outputs can be disabled, multiple drivers can share a bus when only one device is actively enabled, provided the system obeys the relevant electrical and timing constraints.
The 74HC245D is manufactured using silicon-gate C2MOS technology and is specified as a high-speed CMOS logic device. Its transceiver architecture is non-inverting, so the data presented on one bus is transferred without intentional logic inversion when the corresponding direction is selected. The package is a 20-SOIC surface-mount package, matching the distributor listing for Toshiba Semiconductor and Storage.
Typical applications include bidirectional data buses, microcontroller peripheral interfaces, memory-bus isolation, industrial control systems, and communication equipment. When designing a PCB, preserve the manufacturer pin assignment, provide adequate supply decoupling, and route high-speed bus traces with controlled impedance where required. Confirm enable polarity and direction timing before connecting external circuitry.
This product page combines the verified manufacturer and distributor descriptions with package, application, and sourcing context. Electrical limits such as supply voltage, propagation delay, output current, and operating temperature were not included in the supplied source data and are therefore not inferred here.
Alternativas directas para 74HC245D — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
SN74HC245N
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74HC245NSR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74HC245D,653
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74HC245D
✅ Sustitución directa✓ En stock
$0.1011 / unidad
Ver hoja de datos →74HC245
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74HC245D Valores máximos y características eléctricas
| Product Type | Octal bus transceiver |
| Data Direction | Bidirectional, selectable by DIR |
| Logic Family | 74HC high-speed CMOS |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Output State | 3-state output |
| Polarity | Non-inverting |
| Technology | Silicon-gate C2MOS |
| Encapsulado | 20-SOIC |
| Tipo de montaje | Surface Mount |
| Output Enable | Active-low OE control |
| Direction Control | DIR input |
| Application | Asynchronous two-way bus communication |
Guía de configuración de pines de 74HC245D 20-soic
Configuración de pines para 74HC245D (encapsulado 20-soic). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para 74HC245D.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
74HC245D es adecuado para 6 aplicacións: Bidirectional Digital Data Bus, Microcontroller Peripheral Interface, Memory-Bus Isolation, Industrial Control Signal Conditioning, Communication Equipment Backplane, Instrumentation and Test Systems.
Bidirectional Digital Data Bus
The 74HC245D fits a bidirectional digital data bus because it provides eight parallel channels, selectable direction, and three-state outputs in a 20-SOIC package. It can connect a controller-side bus to a peripheral-side bus while keeping disabled outputs isolated. The verified source identifies asynchronous two-way communication and does not provide propagation-delay limits, so timing margins must be checked against the system clock and load before deployment.
Recomendado
Microcontroller Peripheral Interface
For a microcontroller peripheral interface, the 74HC245D can buffer eight data lines and place the outputs in a high-impedance state when the bus is not selected. This is useful when several peripheral buses share a common wiring harness or when a controller must control propagation between circuit domains. Verify the controller voltage, input thresholds, output drive, and enable timing because those ratings are not present in the supplied source snippets.
Recomendado
Memory-Bus Isolation
The 74HC245D can be used around a memory-bus segment when the designer needs controlled bidirectional access and tri-state isolation rather than permanent two-way loading. The eight-bit width matches common parallel data structures, while DIR selects the active transfer direction and OE isolates the outputs during idle periods. The verified material does not include memory-specific voltage, timing, or drive values, so compatibility with a particular memory must be established from the complete datasheets.
Recomendado
Industrial Control Signal Conditioning
The 74HC245D is suitable as a digital isolation and buffering element in industrial control assemblies that need to distribute eight control or status lines while preventing bus contention. Three-state outputs allow a controller to disconnect a branch during maintenance or alternate addressing intervals. Industrial suitability cannot be inferred from the basic logic description; confirm supply tolerance, noise margins, temperature range, and any required industrial qualification from the selected manufacturer documentation.
Recomendado
Communication Equipment Backplane
In communication equipment, the 74HC245D can support parallel control or status paths on a backplane where bidirectional access and bus isolation are required. The octal organization allows a complete byte to be routed in one device, and the tri-state outputs help avoid multiple drivers during module selection. The verified source provides the functional architecture but not insertion, removal, or hot-plug specifications, so designers should review the manufacturer’s timing and operating limits before using the part in live backplanes.
Recomendado
Instrumentation and Test Systems
The 74HC245D can buffer parallel command and measurement-control lines in instrumentation systems where several modules must share a bus and inactive modules must present high impedance. Its non-inverting transceiver structure simplifies control-logic design, while the 20-SOIC package supports conventional surface-mount assembly. Because the supplied source does not specify noise, timing, or temperature characteristics, laboratory instrumentation should validate the complete electrical envelope and grounding strategy before deployment.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para 74HC245D — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN74HC245N | SN74HC245NSR | 74HC245D,653 | 74HC245 |
|---|---|---|---|---|---|
| Package | 20-SOIC | SOIC-20 | SOIC-20 | 20-SO | SOIC-20 variant |
| Brand | Toshiba Semiconductor and Storage | Texas Instruments | Texas Instruments | NXP Semiconductors | NXP Semiconductors |
| Function | Octal bus transceiver | Octal bus transceiver | Octal bus transceiver | Octal bus transceiver | Octal bus transceiver |
| Data Width | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state |
| Direction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Logic Family | 74HC CMOS | 74HC CMOS | 74HC CMOS | 74HC CMOS | 74HC CMOS |
Diferenciadores clave
- Eight-channel bidirectional interface (frente a SN74HC245N)
- Toshiba 20-SOIC listing (frente a 74HC245D,653)
- Three-state bus isolation (frente a SN74HC245NSR)
- C2MOS high-speed CMOS positioning (frente a 74HC245)
Notas de diseño
Keep the transceiver’s supply decoupling close to its power pins and preserve the manufacturer’s 20-SOIC footprint and pin numbering. Route the eight data lines as a grouped parallel channel where practical, minimize stubs, and keep the DIR and OE control traces away from sensitive analog or clock paths. Because the supplied data does not include a complete pinout, verify every connection against the selected manufacturer datasheet before fabrication.
Do not enable two output drivers onto the same bus unless the system explicitly supports bus contention and all timing constraints are satisfied. Use the OE function to place inactive devices in the high-impedance state, and check the manufacturer’s direction-control and output-enable truth tables. The verified snippets do not provide propagation-delay values, so enable/dead-time timing must be calculated from the complete datasheet.
Validate the actual supply voltage, input thresholds, output drive, and input/output current before using the 74HC245D between voltage domains. The retrieved data identifies a high-speed CMOS transceiver but does not provide its voltage limits, so it cannot by itself establish 3.3 V/5 V level-shifting suitability. Add local supply bypass, maintain return-current continuity, and verify the selected manufacturer’s absolute-maximum and recommended-operating ratings.
Información de cumplimiento
The supplied verified data does not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. AEC-Q100 is not applicable to the supplied general-purpose logic-device description.
