SN74AVC4T245PWR - 4-Bit Dual-Supply Level Shifter | TI
N.º de pieza: SN74AVC4T245PWR ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0.78 | $0,78 |
| 10 | $0.7 | $7,00 |
| 100 | $0.55 | $55,00 |
| 500 | $0.46 | $230,00 |
| 1.000 | $0.38 | $380,00 |
SN74AVC4T245PWR Descripción general
A bus transceiver is a digital integrated circuit that transfers data bidirectionally between two buses, using direction-control and output-enable inputs plus 3-state outputs so multiple devices can share a common bus. The SN74AVC4T245 belongs to the voltage translator (level shifter) family within the broader logic IC and interface IC hierarchy, and it is essential in mixed-voltage systems where MCUs, FPGAs, sensors, and memory operate at different logic levels.
Key features include configurable voltage translation on both ports, control inputs (1DIR, 2DIR, 1OE, 2OE) referenced to VCCA for simplified control logic, and Ioff partial-power-down circuitry that disables outputs and prevents damaging backflow current when either rail is at GND. A VCC isolation feature places all I/O in high-impedance if either supply is absent.
Technically, the device supports asynchronous communication between two data buses at data rates up to 380 Mbps with a typical propagation delay around 2.5 ns, suiting high-speed SPI, parallel bus, and GPIO interfaces. The TSSOP-16 package has a 4.4mm body width and 0.65mm pin pitch for space-constrained PCBs.
Typical applications include level shifting for SPI, UART, I2C-adjacent GPIO expansion, and FPGA or ASIC interconnects in industrial control, portable battery-powered electronics, and automotive modules where multiple voltage domains coexist.
Design tip: keep the DIR and OE pins driven from VCCA-domain logic and place 0.1uF decoupling capacitors close to both VCCA and VCCB pins; avoid bus contention by sequencing direction changes with a brief high-impedance interval.
Alternativas directas para SN74AVC4T245PWR — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SN74AVC4T245PWR (mismo factor de forma y huella) — difiere en Output Type, Package.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
SN74AVCH4T245PWR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74AVC4T245PWR
✅ Sustitución directa✓ En stock
$0.38 / unidad
Ver hoja de datos →SN74LVC4T245PWR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74AVC4T245PW,112
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
SN74AVC4T245PWT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74AVC4T245PWR Valores máximos y características eléctricas
| Función | 4-bit dual-supply bus transceiver with configurable voltage translation |
| Supply Voltage VCCA | 0.8 V to 3.6 V |
| Supply Voltage VCCB | 0.8 V to 3.6 V |
| Translation Direction | Bidirectional, any VCCA/VCCB combination |
| Max Data Rate | 380 Mbps |
| Tipo de salida | 3-State |
| Control Inputs | 1DIR, 2DIR, 1OE, 2OE (referenced to VCCA) |
| Ioff Partial Power Down | Yes |
| VCC Isolation | Yes - I/O high impedance if either rail at GND |
| Encapsulado | 16-TSSOP (PW), 4.4 mm body, 0.65 mm pitch |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
| Packaging | Tape & Reel (PWR suffix) |
Configuración de pines de SN74AVC4T245PWR
| Pin 1 | 1OE — Output enable 1 (active low, referenced to VCCA) |
| Pin 2 | 1DIR — Direction control port 1 (referenced to VCCA) |
| Pin 3 | A1 — Port A data 1 |
| Pin 4 | A2 — Port A data 2 |
| Pin 5 | VCCA — A-side supply, 0.8V to 3.6V |
| Pin 6 | A3 — Port A data 3 |
| Pin 7 | A4 — Port A data 4 |
| Pin 8 | GND — Ground |
| Pin 9 | B4 — Port B data 4 |
| Pin 10 | B3 — Port B data 3 |
| Pin 11 | B2 — Port B data 2 |
| Pin 12 | B1 — Port B data 1 |
| Pin 13 | VCCB — B-side supply, 0.8V to 3.6V |
| Pin 14 | 2DIR — Direction control port 2 (referenced to VCCA) |
| Pin 15 | 2OE — Output enable 2 (active low, referenced to VCCA) |
Aplicaciones típicas
SN74AVC4T245PWR es adecuado para 6 aplicacións: SPI Level Shifting (3.3V MCU to 1.8V Peripheral), FPGA / ASIC Mixed-Voltage I/O Interconnect, Automotive ECU Voltage Domain Bridging, Portable Battery-Powered Electronics, Industrial PLC and Control Module Interfaces, UART and GPIO Expansion Between Logic Domains.
SPI Level Shifting (3.3V MCU to 1.8V Peripheral)
The SN74AVC4T245PWR translates SPI signals between a 3.3V MCU and 1.8V flash, sensor, or display devices using VCCA=3.3V and VCCB=1.8V. Its 380 Mbps data rate comfortably supports SPI clocks of 50 MHz or more, and the 3-state outputs let one DIR pin per port steer MOSI (A-to-B) and MISO (B-to-A) independently. Place 0.1uF decoupling at both VCCA and VCCB; the Ioff feature prevents backfeed when the 1.8V rail is powered down.
Recomendado
FPGA / ASIC Mixed-Voltage I/O Interconnect
In FPGA systems, bank voltages often differ from ASIC or backplane logic levels. The SN74AVC4T245PWR bridges a 2.5V or 3.3V bank to a 1.2V/1.5V ASIC domain, with the VCC isolation feature forcing all I/O high-impedance if either rail collapses, protecting the fragile low-voltage die. The 380 Mbps rate and ~2.5 ns typical delay preserve timing margins on parallel configuration or data buses in industrial and communications equipment.
Recomendado
Automotive ECU Voltage Domain Bridging
Automotive ECUs combine 3.3V microcontrollers with 1.8V safety MCUs and sensors. The pin-compatible, AEC-Q100 qualified SN74AVC4T245QPWRQ1 shares this footprint, so boards designed around the standard AVC4T245 can migrate to automotive grade without layout changes. Control pins referenced to VCCA simplify interfacing with the primary 3.3V domain, while Ioff circuitry safely isolates I/O during partial-power-down crank conditions.
Recomendado
Portable Battery-Powered Electronics
In battery products, a boost converter may supply 3.3V while a power-frugal PMIC rail runs at 1.2V or 1.8V. The SN74AVC4T245PWR's 0.8V minimum VCC accommodates aggressively scaled low-voltage domains, and its Ioff plus VCC isolation features prevent leakage back into unpowered rails, extending battery life. The 4.4mm-wide TSSOP-16 keeps the footprint small for wearables and handheld instrument GPIO expansion.
Recomendado
Industrial PLC and Control Module Interfaces
Industrial controllers mix 3.3V logic with 5V-tolerant or 2.5V field-side signaling. The SN74AVC4T245PWR buffers parallel status and command buses between domains with 3-state outputs that allow multiple cards to share a backplane bus via the OE pins. Direction changes sequenced through DIR with a high-impedance interval prevent contention. Its robust dual-rail design tolerates supply sequencing in either order, simplifying hot-swap slot design.
Recomendado
UART and GPIO Expansion Between Logic Domains
For UART, I2C-adjacent GPIO, and general-purpose control signaling between a 1.8V SoC and 3.3V peripherals, the SN74AVC4T245PWR provides four buffered bidirectional channels. Configurable translation means no pull-up resistor schemes (unlike TXS-family passive translators), giving clean, fast edges at high data rates. Tying OE low for always-on GPIO or gating it for power savings offers design flexibility in networking modules and IoT gateways.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SN74AVC4T245PWR — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN74AVCH4T245PWR | SN74AVC4T245QPWRQ1 | SN74LVC4T245PWR | 74AVC4T245PW,112 |
|---|---|---|---|---|---|
| Package | 16-TSSOP (PW) | 16-TSSOP (PW) - same | 16-TSSOP (PW) - same | 16-TSSOP (PW) - same | 16-TSSOP (PW) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | NXP (Nexperia) |
| Supply Voltage Range | 0.8V to 3.6V (both rails) | 0.8V to 3.6V | 0.8V to 3.6V | 1.65V to 3.6V | 0.8V to 3.6V |
| Bit Width | 4-bit | 4-bit | 4-bit | 4-bit | 4-bit |
| Bus Hold Inputs | No | Yes | No | No | No |
| Ioff Partial Power Down | Yes | Yes | Yes | Yes | Yes |
| Automotive Grade | No | No | Yes (AEC-Q100) | No | No |
| 5V Tolerant I/O | No | No | No | Yes | No |
Diferenciadores clave
- True sub-1V support on both ports (frente a SN74LVC4T245PWR)
- Automotive-grade drop-in option (frente a SN74AVC4T245QPWRQ1)
- Bus-hold variant available (frente a SN74AVCH4T245PWR)
- Active-drive translation vs passive schemes (frente a TXB0104QRUTRQ1)
Notas de diseño
Place 0.1uF ceramic decoupling capacitors within 2 mm of both VCCA and VCCB pins, each with a low-impedance ground return. The AVC family switches fast (380 Mbps class), so supply inductance directly translates to ground bounce and ringback on data lines. A solid ground plane under the TSSOP-16 and short (under 10 mm) traces to the translated bus keep signal integrity within the 2.5 ns typical propagation-delay budget.
Control inputs 1DIR, 2DIR, 1OE, and 2OE are referenced to VCCA per the TI datasheet - drive them from VCCA-domain logic only, or use a small-signal translator if the controller lives on the VCCB domain. When reversing bus direction, disable outputs (OE high) for at least one bus turnaround interval before toggling DIR to avoid momentary bus contention and crowbar current between opposing drivers.
The device powers up safely in either rail order thanks to the VCC isolation feature, but decouple each rail independently and do not share a single decoupling network between VCCA and VCCB - the whole point of dual rails is domain isolation. For partial-power-down systems, the Ioff circuitry blocks backflow current, so no external isolation diodes are needed when one domain is unpowered.
Do not exceed 3.6V on either VCCA or VCCB - this family is not 5V tolerant on supplies or I/O; use SN74LVC4T245PWR instead if 5V tolerance is required. Also note the standard AVC4T245 lacks bus-hold: floating A or B inputs after power-up can oscillate; select SN74AVCH4T245PWR if bus-hold is needed, or drive all inputs valid.
Información de cumplimiento
RoHS compliant per TI product page and distributor listings. Automotive version (SN74AVC4T245QPWRQ1) is available separately; the standard PWR is not AEC-Q100 qualified.
