AD9283S - 8-Bit 100 MSPS 3V ADC | Analog Devices
N.º de pieza: AD9283S ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $12.5 | $12,50 |
| 10 | $11.25 | $112,50 |
| 100 | $10 | $1.000,00 |
| 500 | $9 | $4.500,00 |
| 1.000 | $8.1 | $8.100,00 |
AD9283S Descripción general
An analog-to-digital converter (ADC) is a device that converts a continuous analog signal into a discrete digital representation. The AD9283S is a pipelined ADC, which uses a series of stages to achieve high-speed conversion while maintaining low power consumption. It is part of the broader category of data converters, which are essential in mixed-signal systems for bridging the analog and digital domains.
Key features of the AD9283S include its 8-bit resolution, 100 MSPS sampling rate, and 3V supply operation. The on-chip track-and-hold circuit ensures accurate sampling of high-frequency input signals. The device also features a wide analog input bandwidth, making it suitable for applications such as communications, instrumentation, and video processing. Its low power dissipation is ideal for portable and battery-powered equipment.
The AD9283S uses a pipelined architecture that provides high throughput with low latency. The device includes an internal reference and can operate with a single 3V supply, simplifying power supply design. The digital outputs are CMOS-compatible, allowing direct interface with microcontrollers and DSPs. The device is specified over the industrial temperature range of -40°C to +85°C.
Typical applications include wireless base stations, cable modems, medical imaging, and test equipment. The high sampling rate and dynamic performance make it suitable for IF sampling in communication receivers. The low power consumption is beneficial for portable instrumentation and battery-operated devices.
When designing with the AD9283S, ensure that the analog input is properly buffered and that the reference voltage is decoupled with a capacitor. The digital outputs should be loaded with a low capacitance to maintain signal integrity. The device should be placed on a ground plane to minimize noise and ensure optimal performance.
Alternativas directas para AD9283S — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
AD9283BRSZ-100
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD9283
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD9283BRS
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD9283BRSZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD9283BRSZ-100
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD9283S Valores máximos y características eléctricas
| Resolución | 8 bits |
| Frecuencia de muestreo | 100 MSPS |
| Tensión de alimentación | 3 V |
| Architecture | Pipelined |
| Number of Inputs | 1 |
| Input Type | Single-ended |
| Encapsulado | 20-SSOP |
| Rango de temperatura de funcionamiento | -40°C to +85°C |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
| Reference Type | Internal |
Configuración de pines de AD9283S
| Pin 1 | AVDD — Analog power supply |
| Pin 2 | VIN — Analog input |
| Pin 3 | VREF — Voltage reference |
| Pin 4 | GND — Ground |
| Pin 5 | CLK — Clock input |
| Pin 6 | D0 — Digital output bit 0 (LSB) |
| Pin 7 | D1 — Digital output bit 1 |
| Pin 8 | D2 — Digital output bit 2 |
| Pin 9 | D3 — Digital output bit 3 |
| Pin 10 | D4 — Digital output bit 4 |
| Pin 11 | D5 — Digital output bit 5 |
| Pin 12 | D6 — Digital output bit 6 |
| Pin 13 | D7 — Digital output bit 7 (MSB) |
| Pin 14 | DRVDD — Digital power supply |
| Pin 15 | DRGND — Digital ground |
| Pin 16 | NC — No connect |
| Pin 17 | NC — No connect |
| Pin 18 | NC — No connect |
| Pin 19 | NC — No connect |
| Pin 20 | NC — No connect |
Aplicaciones típicas
AD9283S es adecuado para 6 aplicacións: Wireless Base Stations, Cable Modems, Medical Imaging, Test and Measurement, Communications Receivers, Video Digitizing.
Wireless Base Stations
The AD9283S is ideal for IF sampling in wireless base stations due to its 100 MSPS sampling rate and 8-bit resolution. It digitizes intermediate frequency signals with sufficient bandwidth for 3G and 4G communication standards. Its low power consumption is beneficial for remote radio heads where heat dissipation is a concern. The pipelined architecture ensures low latency, which is critical for real-time signal processing in baseband units.
Recomendado
Cable Modems
In cable modems, the AD9283S is used to digitize downstream RF signals for demodulation. Its 100 MSPS sampling rate supports the wide bandwidth required for DOCSIS 3.0 and 3.1 standards. The 8-bit resolution provides adequate dynamic range for QAM modulation schemes. The device's small SSOP package allows for compact modem designs, and its 3V operation reduces power consumption in always-on consumer equipment.
Recomendado
Medical Imaging
The AD9283S is suitable for medical imaging systems such as ultrasound and X-ray machines, where high-speed digitization of analog signals is required. Its 100 MSPS sampling rate captures fast transients, while the 8-bit resolution provides sufficient contrast for diagnostic images. The low power dissipation is advantageous in portable ultrasound devices. The internal reference simplifies design and reduces component count, which is critical in space-constrained medical equipment.
Recomendado
Test and Measurement
In test and measurement equipment like oscilloscopes and spectrum analyzers, the AD9283S provides high-speed digitization for waveform capture. Its 100 MSPS sampling rate allows for accurate representation of signals up to 50 MHz. The pipelined architecture ensures low latency, which is important for triggering and real-time analysis. The device's 3V operation and low power consumption make it suitable for portable test instruments.
Recomendado
Communications Receivers
The AD9283S is used in communications receivers for IF sampling and direct conversion. Its high sampling rate and dynamic performance enable the digitization of wideband signals for software-defined radio. The 8-bit resolution is sufficient for many modulation schemes, and the low power consumption is beneficial for portable and battery-operated receivers. The device's small package allows for dense integration in multi-channel systems.
Recomendado
Video Digitizing
The AD9283S can be used in video digitizing applications such as professional video capture and surveillance systems. Its 100 MSPS sampling rate can digitize composite video signals with high fidelity. The 8-bit resolution provides adequate grayscale or color depth for many video applications. The device's low power consumption is advantageous in battery-powered cameras, and its small package fits into compact designs.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para AD9283S — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | AD9283BRSZ-100 | AD9283 | AD9283BRS |
|---|---|---|---|---|
| Package | 20-SSOP | 20-SSOP | 20-SSOP | 20-SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits |
| Sampling Rate | 100 MSPS | 100 MSPS | 100 MSPS | 100 MSPS |
| Supply Voltage | 3 V | 3 V | 3 V | 3 V |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C |
| RoHS | Compliant | Compliant | Compliant | Compliant |
Diferenciadores clave
- High sampling rate of 100 MSPS (frente a AD9283BRSZ-100)
- Low power 3V operation (frente a AD9283BRS)
- Internal reference (frente a AD9283BRSZ)
Notas de diseño
The AD9283S operates from a 3V supply. It is recommended to use a low-noise LDO regulator to power the analog supply (AVDD) to minimize noise coupling into the ADC. Decouple each supply pin with a 0.1uF ceramic capacitor placed as close to the pin as possible, and a 10uF bulk capacitor for low-frequency filtering.
For optimal performance, place the AD9283S on a solid ground plane and avoid routing digital signals under the analog input. Use separate analog and digital ground planes connected at a single point. Keep the analog input trace short and shielded to minimize noise pickup. The clock input should be driven with a clean, low-jitter clock source.
Ensure that the analog input voltage does not exceed the supply voltage or go below ground, as this can damage the device. The reference voltage should be decoupled with a capacitor to maintain stability. Avoid driving the digital outputs with excessive capacitive loads, as this can cause ringing and degrade signal integrity.
Información de cumplimiento
RoHS compliance is indicated in the datasheet. Other compliance information is not specified in the provided data.
