AD9951YSV - 400 MSPS 14-Bit DDS | Analog Devices
N.º de pieza: AD9951YSV ✓ ActivoAD9951YSV Descripción general
A direct digital synthesizer, or DDS, is a frequency-generation technique in which a digital phase accumulator advances a phase word at a controlled clock rate, and the resulting phase address selects an amplitude value from a lookup table. Unlike a conventional analog local-oscillator chain, a DDS supports digitally programmed frequency, phase, and amplitude adjustments through a serial interface while retaining high frequency stability derived from its reference clock.
The AD9951YSV provides a 400 MSPS internal clock, a 32-bit frequency-tuning word, and a 14-bit output DAC. Its phase noise is specified at -120 dBc/Hz at a 1 kHz offset from the DAC output. Dynamic performance includes greater than 80 dB spurious-free dynamic range at 160 MHz with a 100 kHz offset. Serial I/O controls the device, while an AOUT output provides the analog result. The 1.8 V CMOS architecture supports low-voltage integration with high-speed digital systems.
The internal architecture separates frequency and phase accumulation from the DAC conversion path, allowing the frequency tuning word, phase offset, and amplitude scale factor to be loaded independently. This architecture supports rapid frequency hopping, precise channel selection, and calibrated phase control. An on-chip oscillator can operate with an external crystal connected to the REFCLK and REFCLKB inputs, with a reference-clock range of 20 MHz to 30 MHz specified for that configuration.
Typical applications include communications test equipment, frequency synthesizers, clock-generation modules, digital waveform sources, and local-oscillator subsystems. The device is also appropriate for radar, instrumentation, and phased-array signal chains where digitally controlled phase adjustment improves channel alignment.
When laying out a circuit, treat the reference clock, serial interface, and analog output as separate high-speed paths. Route the exposed-pad thermal connection through the package thermal design, and use a controlled impedance connection for the analog output to avoid reflections or unwanted harmonics.
This page combines device specifications, practical integration guidance, sourcing information, and verified alternatives. It also identifies the electrical and pinout details that should be checked in the manufacturer data sheet before a new PCB layout is released.
Alternativas directas para AD9951YSV — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
AD9951YSVZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
AD9951YSV Especificaciones
| Device Type | Direct Digital Synthesis IC |
| Internal Clock Speed | 400 MSPS |
| DAC Resolution | 14 bit |
| Frequency Tuning Word | 32 bit |
| Tensión de alimentación | 1.8 V |
| Process Technology | 1.8 V CMOS |
| Phase Noise | -120 dBc/Hz at 1 kHz offset, DAC output |
| Spurious-Free Dynamic Range | >80 dB at 160 MHz, ±100 kHz offset |
| Control Interface | Serial I/O |
| Analog Output | AOUT |
| External Crystal Reference Range | 20 MHz to 30 MHz |
| Reference Clock Inputs | REFCLK and REFCLKB |
| Encapsulado | 48-lead TQFP-EP, 7 mm × 7 mm |
| Tipo de montaje | Surface Mount |
| Data Sheet Revision | Rev. D |
| New Design Status | Recommended for new designs |
Guía de configuración de pines de AD9951YSV 48-lead tqfp-ep, 7 mm × 7 mm
Configuración de pines para AD9951YSV (encapsulado 48-lead tqfp-ep, 7 mm × 7 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para AD9951YSV.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
AD9951YSV es adecuado para 6 aplicacións: Communications Frequency Synthesizer, Digital Waveform and Signal Source, Phased-Array Phase Control, Clock and LO Generation Module, Radar and Signal-Simulation Front End, Industrial Frequency-Control Module.
Communications Frequency Synthesizer
The AD9951YSV fits communications frequency-generation blocks that require rapid, digitally controlled channel changes. Its 32-bit tuning word provides fine frequency resolution, while the 400 MSPS internal clock supports high-rate phase accumulation. A 32-bit serial interface allows the tuning word, phase offset, and amplitude scale factor to be updated without external RAM. The integrated 14-bit DAC simplifies the analog output path, and the greater than 80 dB SFDR specification at 160 MHz provides useful margin when separating wanted energy from close-in harmonics. Use a low-jitter reference clock and short, isolated reference routing to preserve the specified phase-noise performance.
Recomendado
Digital Waveform and Signal Source
The AD9951YSV can generate calibrated sinusoidal outputs for instrumentation and automated test systems. Programmable frequency, phase, and amplitude control make it suitable for stimulus generation where multiple tones or stepped sweeps must be produced with repeatable settings. The 14-bit DAC provides the analog output directly, while the 400 MSPS clock rate supports high-output-frequency operation. The -120 dBc/Hz phase-noise figure at a 1 kHz offset is relevant when close carrier-to-noise performance matters. Place the AOUT connection behind a controlled-impedance network and calibrate output amplitude at the final load rather than only at the device pin.
Recomendado
Phased-Array Phase Control
The AD9951YSV is appropriate for phased-array clock and local-oscillator subsystems because each channel can receive a phase-offset command over the serial interface. The 32-bit tuning word supports precise frequency placement, and the independent phase adjustment helps align multiple channels without changing their final output frequencies. The integrated DAC removes one external conversion stage, while the 400 MSPS clocking capability supports demanding modulation schemes. A shared low-noise reference can synchronize multiple devices, but each channel still needs independent serial routing and careful supply isolation. Validate phase accuracy at the antenna or array output because delay through cables, filters, and amplifiers can offset the programmed device setting.
Recomendado
Clock and LO Generation Module
The AD9951YSV works well as a programmable local oscillator in clocks, modems, and instrumentation modules. Digital frequency updates allow rapid retuning without mechanically adjustable components, and the serial control interface supports deterministic system configuration. With an external crystal connected to REFCLK and REFCLKB, the reference path can be kept predictable in the 20 MHz to 30 MHz range identified by the manufacturer. The integrated 14-bit output DAC reduces external component count and allows amplitude to be scaled in the digital domain. Use dedicated reference and analog-return routing, and decouple the serial bus from sensitive clock nodes to prevent command-transition coupling.
Recomendado
Radar and Signal-Simulation Front End
The AD9951YSV can supply a programmable excitation tone for radar and communications signal-simulation systems. The 400 MSPS internal clock enables high-rate frequency synthesis, while the 32-bit tuning word gives engineers fine control over channel spacing. Greater than 80 dB SFDR at 160 MHz helps maintain separation between the intended tone and nearby spurs. Serial phase and amplitude control also supports scenario generation across multiple channels. Because simulator accuracy depends on reference quality, use a low-jitter reference and treat the analog output as a controlled RF signal path. The exposed thermal pad and analog output require careful layout in compact multi-channel equipment.
Recomendado
Industrial Frequency-Control Module
The AD9951YSV is suitable for industrial controls that require a stable, digitally adjustable excitation or reference signal. The 32-bit tuning word supports fine setting resolution, and the serial interface allows the operating point to be changed from a controller without mechanical adjustment. The integrated DAC makes the output amplitude digitally controllable, which is useful for closed-loop calibration routines. A crystal-referenced configuration can support stable operation across temperature when the crystal and power design are handled correctly. Keep the 1.8 V supply rail quiet, provide the recommended local bypassing, and isolate the AOUT path from digital return currents to avoid injecting modulation products into the controlled signal.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para AD9951YSV — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | AD9951YSVZ |
|---|---|---|
| Package | 48-lead TQFP-EP (7 mm × 7 mm) | 48-lead TQFP-EP (7 mm × 7 mm) |
| Brand | Analog Devices | Analog Devices |
| Internal Clock Speed | 400 MSPS | 400 MSPS |
| DAC Resolution | 14 bit | 14 bit |
| Frequency Tuning Word | 32 bit | 32 bit |
| Supply Voltage | 1.8 V | 1.8 V |
| Phase Noise | -120 dBc/Hz at 1 kHz offset, DAC output | -120 dBc/Hz at 1 kHz offset, DAC output |
| Spurious-Free Dynamic Range | >80 dB at 160 MHz, ±100 kHz offset | >80 dB at 160 MHz, ±100 kHz offset |
| Control Interface | Serial I/O | Serial I/O |
| Analog Output | AOUT | AOUT |
Diferenciadores clave
- Combines high-speed synthesis and conversion in one device (frente a AD9951YSVZ)
- High-frequency dynamic performance (frente a AD9951YSVZ)
- Direct digital control of frequency, phase, and amplitude (frente a AD9951YSVZ)
Notas de diseño
Separate the reference clock, digital serial interface, and analog output into distinct layout zones. Keep the REFCLK and REFCLKB connections short and symmetrical, route SCLK away from AOUT, and provide a continuous ground reference beneath the device. Place local decoupling at the 1.8 V supply pins and use the exposed pad as both the electrical ground connection and primary thermal path.
The exposed thermal pad must be soldered to a PCB ground plane and connected with multiple thermal vias. Keep the via field free of voids where practical, and provide enough copper area to spread heat from the DAC and digital sections. Because maximum output conditions can increase internal dissipation, evaluate the board temperature rise in the final enclosure rather than relying on a copper-pad area calculation alone.
Treat AOUT as a high-speed analog signal and route it over a continuous reference plane with a controlled impedance and the shortest practical path. Terminate according to the intended output topology, avoid stubs, and keep switching nodes and the serial clock away from the output. Calibrate amplitude and phase at the connector or load so that PCB and cable delay do not obscure the programmed DDS setting.
Do not substitute an alternative solely because it uses a 48-lead TQFP package. The replacement must match pin functions, 1.8 V I/O levels, reference-clock arrangement, serial protocol, DAC characteristics, and thermal requirements. When changing between AD9951 order-code suffixes, verify the product-selection table and temperature grade, then confirm the device identifier and register behavior during hardware bring-up.
Información de cumplimiento
Compliance declarations for RoHS, REACH, AEC-Q100, lead-free status, halogen-free status, and conflict minerals were not identified in the device documentation reviewed for this page.