Analog Devices

ADF4216BRUZ-RL - 1.2 GHz Integer-N PLL | Analog Devices

N.º de pieza: ADF4216BRUZ-RL ✓ Activo
5.5 V Vdss 20-pin TSSOP, 4.40 mm body width Package 1.2 GHz Speed
MOQ: 1 |

ADF4216BRUZ-RL Descripción general

Analog Devices ADF4216BRUZ-RL is an integer-N clock and frequency synthesizer with a maximum synthesis frequency of 1.2 GHz, a selectable 3:1 input-to-output ratio, and a 20-pin TSSOP package measuring 4.40 mm in body width. The device combines a PLL with dual-modulus prescaler support and selectable charge-pump currents for programmable frequency generation.

A phase-locked loop, or PLL, is a frequency-control circuit that compares a reference signal with a divided feedback signal and adjusts a controlled oscillator until the phase and frequency match. Within the clock and timing hierarchy, the ADF4216BRUZ-RL is an RF/IF clock-frequency synthesizer, a PLL-based timing IC used to derive stable local signals for communication, instrumentation, and test systems.

The ADF4216BRUZ-RL supports reference or intermediate-frequency prescaler choices of 16/17 and RF prescaler choices of 64/65. Its maximum listed synthesis frequency is 1.2 GHz, and the device includes selectable charge-pump currents for loop design flexibility. A 5.5 V power-supply figure is identified for this family, while the 3-wire programming arrangement supports digital control of operating parameters.

The synthesizer uses an integer-N PLL architecture, providing a direct integer division relationship between the controlled oscillator and reference frequency. That architecture is useful when the required output can be related cleanly to the reference through integer feedback division. The dual-modulus prescaler permits adjacent prescale ratios to be selected, supporting practical divider arrangements while retaining a programmable synthesizer structure.

Typical uses include local oscillator generation for RF and IF signal chains, precision clock generation for measurement equipment, and local frequency references in communication receivers and transmitters. The 20-pin TSSOP format also supports compact surface-mount layouts where board area and assembly cost are important. System designers should verify lock-range, phase-noise, reference, and loop-filter requirements against the manufacturer datasheet for the selected operating mode.

For a stable implementation, use a clean reference source, keep the feedback divider routing compact, and place loop-filter components close to the relevant device pins. Verify the programmed divider ratio, reference frequency, charge-pump setting, and VCO frequency plan before closing the layout. Proper grounding and return paths are especially important when the synthesized clock is close to high-speed digital or RF circuitry.

This page combines the exact device identity, verified package and frequency characteristics, drop-in candidate analysis, technical comparisons, and practical PLL layout guidance. It also identifies engineering parameters that require confirmation in the manufacturer datasheet, helping designers distinguish a true pin-compatible replacement from a superficially similar frequency synthesizer.

Alternativas directas para ADF4216BRUZ-RL — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con ADF4216BRUZ-RL (mismo factor de forma y huella) — difiere en Package, RF Prescaler, Device Type, IF Prescaler, Number of Circuits.

Analog Devices
Package: 20-TSSOP, 4.40 mm width
Comparar con ADF4216BRUZ-RL →
Analog Devices
Package: 20-lead TSSOP, 0.173 in x 4.40 mm width
RF Prescaler: 64/65 selectable dual modulus
Device Type: Dual RF PLL frequency synthesizer (integer-N)
Comparar con ADF4216BRUZ-RL →
Analog Devices
Package: 20-lead TSSOP, 0.173 in x 4.40 mm width
RF Prescaler: 64/65 selectable dual modulus
Device Type: Dual RF PLL frequency synthesizer (integer-N)
Comparar con ADF4216BRUZ-RL →
Analog Devices
Package: 20-lead TSSOP
Device Type: Clock/frequency synthesizer (RF/IF) IC
IF Prescaler: 16/17
Comparar con ADF4216BRUZ-RL →

ADF4216BRUZ

✅ Sustitución directa
Analog Devices
📦 20-pin TSSOP
Clock/frequency synthesizer (RF/IF) IC · Dual RF PLL frequency synthesizer · 1.2 GHz · 1.2 GHz · 2.7 V · 5.5 V · 64/65 · 16/17

Consulte el precio

Ver hoja de datos →

ADF4216BRU

✅ Sustitución directa
Analog Devices
📦 20-pin TSSOP
Dual RF PLL frequency synthesizer (integer-N) · 550 MHz to 1.2 GHz · 5 MHz to 1.2 GHz · 2.7 V to 5.5 V · 3 V to 5.5 V · 64/65 selectable dual modulus · 16/17 selectable dual modulus · Selectable

Consulte el precio

Ver hoja de datos →

ADF4216BRUZ-RL Especificaciones

Product Type Clock/Frequency Synthesizer (RF/IF) IC
PLL Architecture Integer-N
Maximum Synthesis Frequency 1.2 GHz
Number of Circuits 1 circuit
Input-to-Output Ratio 3:1
Input Signal Type CMOS
Output Signal Type Clock
IF or Reference Prescaler 16/17
RF Prescaler 64/65
Maximum Stated Frequency Configuration 550 MHz/1.2 GHz
Power Supply 5.5 V
Charge Pump Selectable current
Programming Interface 3-wire
Encapsulado 20-pin TSSOP, 4.40 mm body width
Tipo de montaje Surface mount

Guía de configuración de pines de ADF4216BRUZ-RL 20-pin tssop, 4.40 mm body width

Configuración de pines para ADF4216BRUZ-RL (encapsulado 20-pin tssop, 4.40 mm body width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 20-pin tssop, 4.40 mm body width para ADF4216BRUZ-RL

No hay datos detallados de patillaje disponibles para ADF4216BRUZ-RL.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

ADF4216BRUZ-RL es adecuado para 6 aplicacións: RF Local Oscillator Generation, IF Signal Chain Clocking, Precision Test and Measurement, Communications Transmitter Reference, Receiver Frequency Synthesis, Industrial Clock Distribution.

🌐

RF Local Oscillator Generation

The ADF4216BRUZ-RL fits RF local-oscillator generation where a programmable clock must be derived from a stable reference and related to a target carrier through integer feedback division. Its maximum listed synthesis frequency is 1.2 GHz, while selectable 16/17 and 64/65 prescaler options provide flexibility in evaluating divider arrangements. Place the synthesizer near the controlled RF path, return its ground pins cleanly, and keep the loop-filter network compact. The principal design trade-off is the integer-N architecture: it simplifies frequency planning, but the final reference-to-output ratio, lock range, phase noise, and spur performance must satisfy the receiver or transmitter requirements.

📡

IF Signal Chain Clocking

The ADF4216BRUZ-RL can provide a programmable IF-related clock in receivers, transmitters, and instrumentation using its RF/IF clock-frequency synthesizer architecture. The 1.2 GHz maximum synthesis frequency provides useful coverage for common intermediate-frequency conversion stages, while the 3:1 input-to-output ratio simplifies some reference plans. Designers should calculate the complete integer division chain and confirm the required operating band rather than relying on the maximum frequency alone. A low-noise reference, short feedback route, controlled return-current path, and carefully selected charge-pump current are central to obtaining predictable jitter and spur performance.

🔧

Precision Test and Measurement

The ADF4216BRUZ-RL is appropriate for programmable clock sources in test and measurement equipment requiring a coherent synthesized output referenced to an external source. Its single-circuit integer-N PLL can establish repeatable output frequencies through prescaler and feedback-divider programming, supporting instrumentation that must combine stability with digital frequency control. The implementation must account for reference spur multiplication, loop bandwidth, phase noise, and output-buffer loading. Use a grounded reference distribution arrangement, maintain compact feedback routing, and validate amplitude and spectral purity at the connector or measurement interface rather than assuming ideal output behavior.

🌐

Communications Transmitter Reference

The ADF4216BRUZ-RL can support a communications transmitter by generating a programmable local reference for RF conversion or modulation stages. Its programmable charge-pump currents and dual-modulus prescaler options allow the loop to be adapted around the selected reference and feedback ratio, while the 20-pin TSSOP package supports compact surface-mount assemblies. Because a transmitter normally places stringent requirements on phase noise, reference spurs, settling time, and output isolation, engineers should verify those characteristics for the actual frequency plan. Keep the synthesizer separated from switching supplies and noisy digital clocks, and use a stable low-noise reference source.

📡

Receiver Frequency Synthesis

The ADF4216BRUZ-RL is suited to receiver architectures requiring a programmable local oscillator or intermediate-frequency clock. Its maximum synthesis frequency of 1.2 GHz covers a substantial portion of common RF and IF conversion plans, and the documented 3:1 input-to-output relationship can reduce complexity in suitable reference arrangements. Receiver design still requires validation of lock behavior at every production frequency, sensitivity to reference phase noise, and output-buffer drive into the next mixer or converter. Preserve continuous ground references around the TSSOP, separate sensitive clock routing from high-current paths, and confirm unused-pin treatment in the manufacturer pin table.

🏭

Industrial Clock Distribution

The ADF4216BRUZ-RL can serve as the programmable source for an industrial clock-distribution subsystem when the system requires a synthesized reference rather than a fixed oscillator. Its 3-wire control interface allows firmware or a controller to configure synthesis parameters, while the 20-pin TSSOP package supports automated board assembly. Designers must ensure the programmed output remains synchronized with the system reference and that each downstream load is compatible with the available clock amplitude and bandwidth. Use impedance-controlled routing where edge rates require it, provide local return paths, and isolate the synthesizer from motors, relays, and switching regulators that could degrade phase noise.

What are the key specifications of ADF4216BRUZ-RL that engineers should know?
The ADF4216BRUZ-RL is a single-circuit, integer-N PLL clock and frequency synthesizer rated for a maximum synthesis frequency of 1.2 GHz and packaged in a 20-pin TSSOP. According to the manufacturer datasheet, it provides 16/17 IF or reference prescaling, 64/65 RF prescaling, selectable charge-pump currents, a 5.5 V power-supply configuration, and a 3-wire programming interface. Its listed input-to-output ratio is 3:1, making it important to verify that the required reference and output frequencies produce an integer feedback relationship.
What is the operating frequency of ADF4216BRUZ-RL?
The ADF4216BRUZ-RL has a maximum listed synthesis frequency of 1.2 GHz and is identified with a 550 MHz/1.2 GHz frequency configuration. According to the manufacturer datasheet, its dual-modulus prescaler supports 16/17 and 64/65 ratios, allowing multiple integer divider arrangements to be evaluated during frequency planning. Maximum synthesis frequency does not mean every output frequency is supported automatically, so the reference frequency, prescaler, feedback division, and valid lock range must be checked together.
Where can I download the ADF4216BRUZ-RL datasheet PDF?
The official ADF4216BRUZ-RL datasheet PDF is available from the Analog Devices product-document library at the manufacturer datasheet link on this page. The document defines the pin functions, register interface, prescaler options, power requirements, and electrical characteristics needed to evaluate the 1.2 GHz integer-N PLL. Use the manufacturer document for final lock-range, phase-noise, electrical-limit, and PCB-design decisions because marketplace summaries do not provide complete programming or timing details.
Where can I find the ADF4216BRUZ-RL pinout?
The ADF4216BRUZ-RL pin assignment is published in the Analog Devices manufacturer datasheet, which describes the 20-pin TSSOP layout and its 3-wire programming interface. The verified component listing confirms a 20-pin TSSOP with a 4.40 mm body width, but it does not reproduce every numbered signal name. Use the pin-description table and package drawing in the datasheet when assigning PCB nets, especially for power, ground, reference, feedback, RF input, and serial programming signals.
Is ADF4216BRUZ-RL suitable for RF and IF clock generation?
The ADF4216BRUZ-RL is suitable for RF and IF clock generation because it is classified as an RF/IF clock and frequency synthesizer and supports programmable frequency synthesis up to 1.2 GHz. According to the manufacturer datasheet, selectable charge-pump currents and dual-modulus prescalers support practical divider planning. Suitability for a specific receiver or transmitter still depends on the reference source, required output range, lock behavior, phase-noise target, and board-level isolation.
How do I design the loop filter for ADF4216BRUZ-RL?
The ADF4216BRUZ-RL loop filter should be calculated from the selected reference frequency, prescaler, feedback division, charge-pump current, VCO characteristics, and the required phase margin. According to the manufacturer datasheet, the device provides selectable charge-pump currents, allowing the loop bandwidth to be tuned without changing the counter configuration. Keep the filter network close to the device, use a stable reference, and verify both in-band phase noise and reference-to-output jitter after layout.
What is the difference between ADF4216BRUZ and ADF4216BRUZ-RL?
ADF4216BRUZ and ADF4216BRUZ-RL use the same 20-pin TSSOP device format and are identified as having consistent terminals, packages, and principal performance characteristics. The cross-reference listing identifies them as completely replaceable without modification to an existing circuit. Their ordering codes differ in packaging or delivery treatment, so engineers should confirm reel configuration, quantity, and any suffix-specific ordering requirements when substituting the parts in production.
Can ADF4216BRU replace ADF4216BRUZ-RL without PCB changes?
The ADF4216BRU can replace ADF4216BRUZ-RL without PCB changes because the cross-reference listing describes the two 20-pin TSSOP parts as completely replaceable, with consistent terminals and principal performance characteristics. The manufacturer family naming indicates that the ordering suffix can distinguish reel or delivery configurations. Confirm the exact ordering requirements, trace quantities, and temperature or grade suffix before treating the substitution as a production BOM approval.
What is the best drop-in replacement for ADF4216BRUZ-RL?
The best verified drop-in choices are ADF4216BRUZ and ADF4216BRU because cross-reference information identifies the same 20-pin TSSOP construction and consistent terminal and performance characteristics, permitting replacement without circuit modification. The -RL designation identifies the reel-delivery ordering option, so the appropriate alternative depends on the required packaging format. No independently verified cross-brand drop-in replacement is identified on this page.
When should I choose ADF4216BRUZ-RL over ADF4212LBRUZ?
Choose ADF4216BRUZ-RL when the design requires a single 1.2 GHz-class integer-N RF/IF synthesizer with a 20-pin TSSOP footprint and the specified 3:1 input-to-output relationship. ADF4212LBRUZ is associated with clock generation extending to 2.4 GHz and is listed as having two circuits in comparison data, so it is not a frequency-for-frequency drop-in substitute. Review prescaler, divider, reference, register-interface, and pin-assignment differences before considering a functional redesign.
Is ADF4216BRUZ-RL the same as ADF4216BRU?
The ADF4216BRUZ-RL and ADF4216BRU are listed as completely replaceable, with consistent terminals, package construction, and principal performance characteristics. Both use a 20-pin TSSOP format, and the cross-reference information states that replacement does not require modification of the existing circuit. They are therefore drop-in alternatives from a circuit-footprint perspective, although orderable packaging and quantity details should still be confirmed.
Where can I buy ADF4216BRUZ-RL online?
Use the Request a Quote form on this page to ask for ADF4216BRUZ-RL availability, current commercial terms, and lead time. The device is an Analog Devices 20-pin TSSOP integer-N PLL with a maximum listed synthesis frequency of 1.2 GHz. A quote request lets the product team confirm the exact -RL ordering configuration and supply status without relying on a stale marketplace listing or an unverified stock indication.
What is the price of ADF4216BRUZ-RL?
Current pricing for ADF4216BRUZ-RL should be obtained through the Request a Quote form on this page because commercial prices change with quantity, availability, and market conditions. The product is the reel-delivery version of a 20-pin TSSOP integer-N PLL rated to 1.2 GHz. Request the quantity-specific quote and lead time for the exact MPN so the order reflects current procurement conditions rather than a historical reference figure.
Is ADF4216BRUZ-RL in stock and what is its lead time?
Current stock and lead time for ADF4216BRUZ-RL should be confirmed through the Request a Quote form on this page. A marketplace summary stating that an item ships today does not establish a stable, orderable stock position for every quantity. When requesting a quote, specify the required quantity, reel format, target date, and any production or traceability requirements so scheduling information reflects the exact order.
What compliance and automotive qualifications apply to ADF4216BRUZ-RL?
The RoHS, REACH, AEC-Q100, lead-free, and halogen-free status of ADF4216BRUZ-RL should be confirmed in the manufacturer product documentation or the relevant declaration for the ordered configuration. The available device listing identifies a 20-pin TSSOP industrial clock synthesizer but does not establish an automotive qualification. Do not infer AEC-Q100 suitability from the -RL ordering suffix; request the applicable compliance documentation during procurement.

Datos de referencia de ingeniería para ADF4216BRUZ-RL — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose ADF4216BRUZ-RL for a compact, programmable integer-N RF or IF clock source requiring a 1.2 GHz-class device, a 3-wire interface, and a 20-pin TSSOP footprint. ADF4216BRUZ is the closest verified circuit-compatible choice when the required orderable packaging is not the -RL reel configuration; cross-reference information identifies consistent terminals and principal performance. ADF4216BRU may also fit an existing 20-pin TSSOP design, but its ordering and frequency-rating details should be checked because another comparison associates it with a 2.4 GHz maximum. ADF4212LBRUZ is not a like-for-like substitution: comparison data associates it with two circuits and up to 2.4 GHz, so it requires a functional and pin-level review. In every case, validate the reference frequency, integer divider plan, lock range, phase noise, spurs, programming registers, temperature grade, and production packaging before approval.

Comparación con alternativas

Parámetro Este producto ADF4216BRUZ ADF4216BRU
Brand Analog Devices Analog Devices Analog Devices
Package 20-pin TSSOP, 4.40 mm body width 20-pin TSSOP 20-pin TSSOP
Product Type Clock/Frequency Synthesizer (RF/IF) IC Clock/Frequency Synthesizer (RF/IF) IC Clock/Frequency Synthesizer (RF/IF) IC
Pin Compatibility ADF4216BRUZ-RL pinout Compatible according to cross-reference listing Compatible according to cross-reference listing

Diferenciadores clave

  • Exact 1.2 GHz family configuration (frente a ADF4216BRU)
  • Pin-compatible ordering option (frente a ADF4216BRUZ)
  • Single-circuit RF/IF synthesis (frente a ADF4212LBRUZ)

Notas de diseño

Place the ADF4216BRUZ-RL close to the reference and feedback divider networks, and route the phase-detector and charge-pump connections using short, symmetric paths. Keep switching-regulator nodes and high-current return paths away from the reference input. A continuous ground reference beneath and around the 20-pin TSSOP is important because divider noise and reference coupling can appear as phase noise or unwanted spurs in the synthesized output.

Validate the complete reference-to-output divider plan before PCB release. The device supports a listed 3:1 input-to-output ratio, but that relationship applies only to the applicable operating configuration. Also evaluate the 64/65 RF and 16/17 IF or reference prescaler choices, the programmed feedback division, and the reference spur contribution. These details determine whether the target output is valid and how reference multiplication affects the final phase-noise and spur requirements.

Provide the 5.5 V power-supply configuration specified for this family using a quiet source and local bypass capacitance selected according to the manufacturer recommendations. Keep the supply and ground return paths compact, and avoid sharing narrow current paths with unrelated noisy loads. Because PLL phase noise and reference spurs can be affected by supply coupling, compare the free-running spectrum against the spectrum with the complete receiver, transmitter, or instrumentation load attached.

Do not treat the 1.2 GHz maximum synthesis frequency as an unrestricted output range. Check the valid prescaler, divider, charge-pump, reference, and operating-frequency combinations in the manufacturer datasheet. Also verify production configuration, temperature grade, reel format, and programming sequence before releasing the BOM. ADF4216BRUZ and ADF4216BRU are circuit-compatible candidates, but the orderable suffix still governs procurement details.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The available product listings do not establish a complete compliance declaration. The component is classified as an RF/IF clock-frequency synthesizer and is not identified as an automotive-qualified product.

Datos verificados el: 2026-11-15 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

ADF4216BRUZ-RL datasheet ADF4216BRUZ-RL pinout ADF4216BRUZ-RL datasheet pdf ADF4216BRUZ-RL replacement ADF4216BRUZ-RL equivalent ADF4216BRUZ-RL price ADF4216BRUZ-RL stock ADF4216BRUZ-RL TSSOP pinout ADF4216BRUZ-RL vs ADF4216BRUZ ADF4216BRUZ-RL vs ADF4216BRU ADF4216BRUZ-RL vs ADF4212LBRUZ Analog Devices ADF4216BRUZ-RL ADF4216BRUZ-RL 1.2 GHz PLL ADF4216BRUZ-RL RF IF clock ADF4216BRUZ-RL loop filter design

Componentes & términos relacionados

Analog Devices ADF4216BRUZ-RL ADF4216BRUZ ADF4216BRU ADF4212LBRUZ clock and frequency synthesizer phase-locked loop PLL integer-N PLL clock and timing IC RF/IF synthesizer local oscillator frequency synthesis prescaler dual-modulus prescaler charge pump selectable charge-pump current 3-wire programming interface TSSOP-20 surface-mount package phase noise reference spur loop filter VCO frequency divider
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ