ADF4216BRUZ-RL - 1.2 GHz Integer-N PLL | Analog Devices
Артикул: ADF4216BRUZ-RL ✓ АктивенADF4216BRUZ-RL Обзор
A phase-locked loop, or PLL, is a frequency-control circuit that compares a reference signal with a divided feedback signal and adjusts a controlled oscillator until the phase and frequency match. Within the clock and timing hierarchy, the ADF4216BRUZ-RL is an RF/IF clock-frequency synthesizer, a PLL-based timing IC used to derive stable local signals for communication, instrumentation, and test systems.
The ADF4216BRUZ-RL supports reference or intermediate-frequency prescaler choices of 16/17 and RF prescaler choices of 64/65. Its maximum listed synthesis frequency is 1.2 GHz, and the device includes selectable charge-pump currents for loop design flexibility. A 5.5 V power-supply figure is identified for this family, while the 3-wire programming arrangement supports digital control of operating parameters.
The synthesizer uses an integer-N PLL architecture, providing a direct integer division relationship between the controlled oscillator and reference frequency. That architecture is useful when the required output can be related cleanly to the reference through integer feedback division. The dual-modulus prescaler permits adjacent prescale ratios to be selected, supporting practical divider arrangements while retaining a programmable synthesizer structure.
Typical uses include local oscillator generation for RF and IF signal chains, precision clock generation for measurement equipment, and local frequency references in communication receivers and transmitters. The 20-pin TSSOP format also supports compact surface-mount layouts where board area and assembly cost are important. System designers should verify lock-range, phase-noise, reference, and loop-filter requirements against the manufacturer datasheet for the selected operating mode.
For a stable implementation, use a clean reference source, keep the feedback divider routing compact, and place loop-filter components close to the relevant device pins. Verify the programmed divider ratio, reference frequency, charge-pump setting, and VCO frequency plan before closing the layout. Proper grounding and return paths are especially important when the synthesized clock is close to high-speed digital or RF circuitry.
This page combines the exact device identity, verified package and frequency characteristics, drop-in candidate analysis, technical comparisons, and practical PLL layout guidance. It also identifies engineering parameters that require confirmation in the manufacturer datasheet, helping designers distinguish a true pin-compatible replacement from a superficially similar frequency synthesizer.
Аналоги без доработки для ADF4216BRUZ-RL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ADF4216BRUZ-RL (тот же форм-фактор и посадочное место) — отличается по Package, RF Prescaler, Device Type, IF Prescaler, Number of Circuits.
ADF4216BRUZ
✅ Прямая заменаУточнить цену
Открыть даташит →ADF4216BRU
✅ Прямая заменаУточнить цену
Открыть даташит →ADF4216BRUZ-RL Характеристики
| Product Type | Clock/Frequency Synthesizer (RF/IF) IC |
| PLL Architecture | Integer-N |
| Maximum Synthesis Frequency | 1.2 GHz |
| Number of Circuits | 1 circuit |
| Input-to-Output Ratio | 3:1 |
| Input Signal Type | CMOS |
| Output Signal Type | Clock |
| IF or Reference Prescaler | 16/17 |
| RF Prescaler | 64/65 |
| Maximum Stated Frequency Configuration | 550 MHz/1.2 GHz |
| Power Supply | 5.5 V |
| Charge Pump | Selectable current |
| Programming Interface | 3-wire |
| Корпус | 20-pin TSSOP, 4.40 mm body width |
| Тип монтажа | Surface mount |
Руководство по цоколевке ADF4216BRUZ-RL в корпусе 20-pin tssop, 4.40 mm body width
Цоколевка для ADF4216BRUZ-RL (корпус 20-pin tssop, 4.40 mm body width). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для ADF4216BRUZ-RL.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
ADF4216BRUZ-RL подходит для 6 применениеs: RF Local Oscillator Generation, IF Signal Chain Clocking, Precision Test and Measurement, Communications Transmitter Reference, Receiver Frequency Synthesis, Industrial Clock Distribution.
RF Local Oscillator Generation
The ADF4216BRUZ-RL fits RF local-oscillator generation where a programmable clock must be derived from a stable reference and related to a target carrier through integer feedback division. Its maximum listed synthesis frequency is 1.2 GHz, while selectable 16/17 and 64/65 prescaler options provide flexibility in evaluating divider arrangements. Place the synthesizer near the controlled RF path, return its ground pins cleanly, and keep the loop-filter network compact. The principal design trade-off is the integer-N architecture: it simplifies frequency planning, but the final reference-to-output ratio, lock range, phase noise, and spur performance must satisfy the receiver or transmitter requirements.
Рекомендуется
IF Signal Chain Clocking
The ADF4216BRUZ-RL can provide a programmable IF-related clock in receivers, transmitters, and instrumentation using its RF/IF clock-frequency synthesizer architecture. The 1.2 GHz maximum synthesis frequency provides useful coverage for common intermediate-frequency conversion stages, while the 3:1 input-to-output ratio simplifies some reference plans. Designers should calculate the complete integer division chain and confirm the required operating band rather than relying on the maximum frequency alone. A low-noise reference, short feedback route, controlled return-current path, and carefully selected charge-pump current are central to obtaining predictable jitter and spur performance.
Рекомендуется
Precision Test and Measurement
The ADF4216BRUZ-RL is appropriate for programmable clock sources in test and measurement equipment requiring a coherent synthesized output referenced to an external source. Its single-circuit integer-N PLL can establish repeatable output frequencies through prescaler and feedback-divider programming, supporting instrumentation that must combine stability with digital frequency control. The implementation must account for reference spur multiplication, loop bandwidth, phase noise, and output-buffer loading. Use a grounded reference distribution arrangement, maintain compact feedback routing, and validate amplitude and spectral purity at the connector or measurement interface rather than assuming ideal output behavior.
Рекомендуется
Communications Transmitter Reference
The ADF4216BRUZ-RL can support a communications transmitter by generating a programmable local reference for RF conversion or modulation stages. Its programmable charge-pump currents and dual-modulus prescaler options allow the loop to be adapted around the selected reference and feedback ratio, while the 20-pin TSSOP package supports compact surface-mount assemblies. Because a transmitter normally places stringent requirements on phase noise, reference spurs, settling time, and output isolation, engineers should verify those characteristics for the actual frequency plan. Keep the synthesizer separated from switching supplies and noisy digital clocks, and use a stable low-noise reference source.
Рекомендуется
Receiver Frequency Synthesis
The ADF4216BRUZ-RL is suited to receiver architectures requiring a programmable local oscillator or intermediate-frequency clock. Its maximum synthesis frequency of 1.2 GHz covers a substantial portion of common RF and IF conversion plans, and the documented 3:1 input-to-output relationship can reduce complexity in suitable reference arrangements. Receiver design still requires validation of lock behavior at every production frequency, sensitivity to reference phase noise, and output-buffer drive into the next mixer or converter. Preserve continuous ground references around the TSSOP, separate sensitive clock routing from high-current paths, and confirm unused-pin treatment in the manufacturer pin table.
Рекомендуется
Industrial Clock Distribution
The ADF4216BRUZ-RL can serve as the programmable source for an industrial clock-distribution subsystem when the system requires a synthesized reference rather than a fixed oscillator. Its 3-wire control interface allows firmware or a controller to configure synthesis parameters, while the 20-pin TSSOP package supports automated board assembly. Designers must ensure the programmed output remains synchronized with the system reference and that each downstream load is compatible with the available clock amplitude and bandwidth. Use impedance-controlled routing where edge rates require it, provide local return paths, and isolate the synthesizer from motors, relays, and switching regulators that could degrade phase noise.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ADF4216BRUZ-RL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ADF4216BRUZ | ADF4216BRU |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin TSSOP, 4.40 mm body width | 20-pin TSSOP | 20-pin TSSOP |
| Product Type | Clock/Frequency Synthesizer (RF/IF) IC | Clock/Frequency Synthesizer (RF/IF) IC | Clock/Frequency Synthesizer (RF/IF) IC |
| Pin Compatibility | ADF4216BRUZ-RL pinout | Compatible according to cross-reference listing | Compatible according to cross-reference listing |
Ключевые отличия
- Exact 1.2 GHz family configuration (против ADF4216BRU)
- Pin-compatible ordering option (против ADF4216BRUZ)
- Single-circuit RF/IF synthesis (против ADF4212LBRUZ)
Заметки по проектированию
Place the ADF4216BRUZ-RL close to the reference and feedback divider networks, and route the phase-detector and charge-pump connections using short, symmetric paths. Keep switching-regulator nodes and high-current return paths away from the reference input. A continuous ground reference beneath and around the 20-pin TSSOP is important because divider noise and reference coupling can appear as phase noise or unwanted spurs in the synthesized output.
Validate the complete reference-to-output divider plan before PCB release. The device supports a listed 3:1 input-to-output ratio, but that relationship applies only to the applicable operating configuration. Also evaluate the 64/65 RF and 16/17 IF or reference prescaler choices, the programmed feedback division, and the reference spur contribution. These details determine whether the target output is valid and how reference multiplication affects the final phase-noise and spur requirements.
Provide the 5.5 V power-supply configuration specified for this family using a quiet source and local bypass capacitance selected according to the manufacturer recommendations. Keep the supply and ground return paths compact, and avoid sharing narrow current paths with unrelated noisy loads. Because PLL phase noise and reference spurs can be affected by supply coupling, compare the free-running spectrum against the spectrum with the complete receiver, transmitter, or instrumentation load attached.
Do not treat the 1.2 GHz maximum synthesis frequency as an unrestricted output range. Check the valid prescaler, divider, charge-pump, reference, and operating-frequency combinations in the manufacturer datasheet. Also verify production configuration, temperature grade, reel format, and programming sequence before releasing the BOM. ADF4216BRUZ and ADF4216BRU are circuit-compatible candidates, but the orderable suffix still governs procurement details.
Информация о соответствии
The available product listings do not establish a complete compliance declaration. The component is classified as an RF/IF clock-frequency synthesizer and is not identified as an automotive-qualified product.