ADM232AARW - 200 kB/s Dual RS-232 Transceiver | Analog Devices
N.º de pieza: ADM232AARW ✗ Fin de vidaADM232AARW Descripción general
An RS-232 transceiver is the interface bridge between a low-voltage digital controller and a physical serial port. The driver converts logic-level signals into RS-232-compatible levels, while the receiver converts bipolar RS-232 signals back into CMOS-compatible logic. As a member of the interface-IC hierarchy, the ADM232AARW belongs to the RS-232 transceiver class, where full-duplex operation, voltage levels, signaling rate, and supply voltage determine its system suitability.
Key features include a 200 kB/s transmission rate, two drivers, two receivers, and receiver input protection to 30 V. The single 5 V supply allows operation from 4.5 V to 5.5 V, eliminating the need for a separate negative rail. The charge-pump network generates the positive and negative voltage levels required by RS-232, while the integrated DC-DC converter supports the on-board receive path. Its industrial temperature range extends from -40°C to +85°C.
The ADM232AARW uses CMOS-compatible driver inputs and receiver outputs, making it suitable for UARTs, microcontrollers, modems, and industrial controllers with conventional 5 V or 3.3 V-compatible interface levels. Its 200 kB/s rate exceeds the throughput of many legacy serial links while retaining the familiar RS-232 electrical interface. The 16-SOIC package also supports automated board assembly and occupies substantially less board area than discrete driver and receiver implementations.
Typical applications include industrial instrumentation, point-of-sale equipment, data acquisition systems, test equipment, and embedded control systems that exchange serial commands over an RS-232 port. It can also support legacy peripherals through short cables, although modern designs must consider ground continuity, protection, and the practical distance limitations of RS-232.
Designers should place the four 0.1 µF charge-pump capacitors close to their assigned pins and route the serial outputs and inputs away from noisy switching circuitry. Input protection to 30 V improves tolerance to accidental voltage excursions, but it does not replace surge protection for cables exposed to industrial transients.
This page combines the ADM232AARW's interface characteristics, verified drop-in references, package-level guidance, and practical comparison criteria to help engineers evaluate board compatibility and select the appropriate RS-232 transceiver.
Alternativas directas para ADM232AARW — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADM232AARW (mismo factor de forma y huella) — difiere en Package, Supply Voltage, Maximum Data Rate, Product Type, Mounting Type.
MAX222CN
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX232ACSE+T
✅ Sustitución directaConsulte el precio
Ver hoja de datos →MAX242
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ST232CWR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ST232ABDR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ADM232AARW Especificaciones
| Product Type | RS-232 line driver and receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 200 kB/s |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Charge-Pump Capacitance | 0.1 µF |
| Number of External Charge-Pump Capacitors | 4 |
| Transmitter Output Swing | 9 V |
| Receiver Input Voltage Rating | 30 V |
| Receiver Hysteresis | 400 mV |
| Onboard DC-DC Converter | Yes |
| Rango de temperatura de funcionamiento | -40°C to +85°C |
| Encapsulado | 16-lead SOIC, surface mount |
| Interface Standard | EIA-232-E and V.28 |
Guía de configuración de pines de ADM232AARW 16-lead soic, surface mount
Configuración de pines para ADM232AARW (encapsulado 16-lead soic, surface mount). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ADM232AARW.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADM232AARW es adecuado para 6 aplicacións: Industrial Instrumentation, Data Acquisition Systems, Test and Measurement Equipment, Point-of-Sale Terminals, Embedded Control and Modem Interfaces, Legacy Peripheral Connectivity.
Industrial Instrumentation
The ADM232AARW fits industrial instruments that exchange commands and measurements through a legacy RS-232 port. Its two-driver, two-receiver arrangement supports full-duplex communication, while the 4.5 V to 5.5 V operating range accommodates conventional 5 V industrial control systems. The 200 kB/s rate provides useful throughput for configuration uploads and real-time status data. Use the four specified 0.1 µF capacitors and keep the serial traces away from switching nodes. For field-wired ports, add suitable external protection because the 30 V receiver rating improves tolerance but does not replace a complete surge-protection strategy.
Recomendado
Data Acquisition Systems
The ADM232AARW is useful in laboratory and industrial data-acquisition systems that must retain compatibility with RS-232 instruments. Two independent receive channels can collect status or trigger information, while two transmit channels support commands and acknowledgments. The single 5 V architecture simplifies board-level supply planning, and the 200 kB/s rate is suitable for moderate-rate telemetry. Place the interface near the connector, provide a low-impedance ground path, and separate the charge-pump capacitor area from precision analog circuitry to reduce potential coupling.
Recomendado
Test and Measurement Equipment
The ADM232AARW can provide the legacy PC-to-instrument interface in test systems whose front panel or rear panel uses an RS-232 connector. Its full-duplex channel count permits simultaneous command transmission and response reception, while the 200 kB/s rate handles remote programming and diagnostic data. The 16-lead SOIC package simplifies automated assembly and provides adequate temperature coverage for controlled equipment environments. Keep the connector-side protection close to the entry point and route the ground return alongside the cable shield where the system design supports it.
Recomendado
Point-of-Sale Terminals
The ADM232AARW is applicable to point-of-sale and service terminals that communicate with legacy peripherals, printers, or controllers through RS-232. Its two transmit and two receive channels allow multiple device roles without duplicating the interface circuitry, while the 5 V supply supports integration with common embedded control platforms. The 200 kB/s rate is more than adequate for short command transactions. Keep the external capacitors close to the IC, provide a common signal ground, and place any connector protection ahead of the receiver inputs.
Recomendado
Embedded Control and Modem Interfaces
The ADM232AARW bridges a conventional UART or controller to an RS-232 network node, making it suitable for embedded controls, service equipment, and modem interfaces. Because it generates bipolar RS-232 levels from one 5 V supply, the design avoids a separate negative power rail. The integrated two-channel structure supports simultaneous request and status traffic, while the 200 kB/s rate covers moderate command streams. Observe the capacitor placement and supply-decoupling recommendations in the Analog Devices application guidance to preserve stable operation during repeated data transmission.
Recomendado
Legacy Peripheral Connectivity
The ADM232AARW is appropriate when an updated controller must connect to an older printer, scanner, instrument, or service interface that only supports RS-232. Two full-duplex channels can support simultaneous data transfer and status reporting, while the single 5 V supply simplifies retrofit boards. Its industrial temperature range supports controlled industrial environments, and the receiver input tolerance of 30 V offers additional margin against moderate voltage excursions. Verify cable length, grounding, and connector-level protection because protocol compatibility alone does not guarantee reliable communication over every RS-232 installation.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADM232AARW — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | MAX222 | MAX232A | MAX242 | ST232CWR | ST232ABDR |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Maxim Integrated | Maxim Integrated | Maxim Integrated | STMicroelectronics | STMicroelectronics |
| Package | 16-lead SOIC | 16-lead SOIC - same | 16-lead SOIC - same | 16-lead SOIC - same | 16-lead SOIC - same | 16-lead SOIC - same |
| RS-232 Channel Configuration | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Nominal Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Drop-In Reference Status | Target device | Reported as pin-compatible | Reported as pin-compatible | Reported as pin-compatible | Same-package functional comparison | Same-package functional comparison |
Diferenciadores clave
- Established Analog Devices 2/2 RS-232 interface implementation (frente a MAX232A)
- Explicit pin-compatible cross-brand sourcing path (frente a ST232ABDR)
- Single-supply charge-pump implementation (frente a MAX242)
Notas de diseño
Place all four 0.1 µF charge-pump capacitors close to their assigned ADM232AARW pins, with short and symmetrical return paths. Keep the capacitor loops compact because long traces can increase circulating current and susceptibility to EMI. Place supply-decoupling capacitance near the 5 V and ground pins, and keep the connector-side protection network separate from the charge-pump area to minimize coupling into the receiver channels.
Route the RS-232 driver outputs directly toward the connector and avoid sharing their paths with clocks, switching-regulator nodes, or sensitive analog inputs. Maintain a nearby ground reference for the interface, and use a ground conductor that can carry the return current over the complete cable path. When the board connects to externally accessible equipment, place the protection elements close to the connector so surge energy is diverted before reaching the receiver inputs.
Do not treat a matching 16-SOIC package as proof of interchangeability. Before substituting MAX222, MAX232A, MAX242, ST232CWR, or ST232ABDR, compare every pin name, charge-pump capacitor connection, receiver-output behavior, shutdown implementation, and supply-current requirement. Also verify the board's logic levels and grounding arrangement; the ADM232AARW receiver input tolerance of 30 V is not a substitute for appropriately rated external surge protection.
RS-232 uses bipolar voltage levels, so cable routing and grounding affect performance even when the UART data rate is modest. Keep transmit and receive traces away from high-current switching paths, use a continuous ground reference, and avoid long unterminated branches. If long cables or noisy industrial environments are expected, add designed protection networks at the connector and validate command timing and error recovery with the intended peripheral rather than relying only on nominal 200 kB/s operation.
Información de cumplimiento
The manufacturer product page and component listings do not state a definitive compliance declaration for ADM232AARW. AEC-Q100 is not applicable because this is an industrial RS-232 interface IC rather than an automotive-qualified device.