ADM238LJNZ - 4/4 RS-232 Transceiver, 5V, 100k BPS | Analog Devices
N.º de pieza: ADM238LJNZ ✓ ActivoADM238LJNZ Descripción general
An RS-232 transceiver is an interface integrated circuit that combines line drivers and line receivers. The driver converts TTL-compatible logic signals into RS-232-compatible levels, while the receiver converts incoming RS-232 signals back into logic levels. In the broader hierarchy, the ADM238LJNZ belongs to the interface IC family, specifically the RS-232 transceiver and communications-interface category. The 24-pin PDIP format supports through-hole assembly and straightforward panel or legacy industrial PCB layouts.
The ADM238L family is designed for low-power operation from a single +5V supply. The manufacturer identifies the device as a 5V CMOS RS-232 driver/receiver set with four drivers and four receivers. Its 100 k BPS communication rate is suitable for moderate-speed data links rather than high-speed synchronous or differential bus applications. The four-channel organization reduces the number of interface packages required when several RS-232 ports must share a common supply and ground architecture.
Typical uses include industrial controllers, barcode and weighing equipment, test systems, security equipment, and board-level communication links. Because the device operates from +5V, it can be placed between a modern microcontroller UART and an external RS-232 connector without requiring a separate bipolar supply. The logic-side interface remains compatible with the voltage levels used by the surrounding digital circuitry, while the line-side interface provides the voltage translation required by RS-232.
PCB implementation should preserve the manufacturer’s recommended decoupling arrangement and provide adequate copper and signal-return paths for the RS-232 connector. RS-232 is an unbalanced, point-to-point interface, so cable length, grounding, protection, and connector transients can influence reliability. Shielded or transient-protected cabling is appropriate when the port is exposed to industrial electrical noise. The manufacturer product page and ADM238L datasheet remain the primary references for pin assignment, electrical limits, and application-circuit details.
This page organizes the ADM238LJNZ specifications, package information, pricing references, pin-level application guidance, and available drop-in cross-reference information into an engineering-focused resource. It also identifies the principal design trade-offs between the ADM238LJNZ and other RS-232 transceiver options, helping designers select the interface device that best fits their voltage, throughput, packaging, and assembly requirements.
Alternativas directas para ADM238LJNZ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADM238LJNZ (mismo factor de forma y huella) — difiere en Maximum Data Rate, Charge-Pump Capacitor, Package, Product Type, Supply Voltage.
ADM238LJN
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADM238LJNZ Especificaciones
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 4 |
| Tensión de alimentación | +5 V |
| Maximum Data Rate | 100 k BPS |
| Logic Compatibility | CMOS |
| Supported Standard | EIA-232-E and V.28 |
| Encapsulado | 24-pin PDIP |
| Tipo de montaje | Through-hole |
| Number of Interface Channels | 4 |
| Supply Type | Single +5 V CMOS supply |
| Power Classification | Low-power RS-232 transceiver |
Guía de configuración de pines de ADM238LJNZ 24-pin pdip
Configuración de pines para ADM238LJNZ (encapsulado 24-pin pdip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ADM238LJNZ.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADM238LJNZ es adecuado para 6 aplicacións: Industrial Controller Serial Ports, Test and Measurement Equipment, Security and Access Equipment, Barcode and Weighing Systems, Embedded Serial Communication Hubs, Legacy Communication Adapters.
Industrial Controller Serial Ports
The ADM238LJNZ is well suited to industrial controllers that need more than one RS-232 connection while operating from a +5V logic supply. Its four drivers and four receivers implement two bidirectional RS-232 ports in one 24-pin PDIP device. The 100 k BPS maximum data rate is suitable for configuration links, service interfaces, and supervisory communication with peripheral equipment. A practical implementation places each transceiver channel near its connector, routes the RX and TX pairs as balanced signal-and-return paths, and keeps switching or high-current traces away from the interface lines. The single +5V supply simplifies the power tree compared with a traditional ±12V RS-232 design.
Recomendado
Test and Measurement Equipment
The ADM238LJNZ can provide two RS-232 links for test and measurement equipment that communicates with legacy instruments, fixture controllers, or service computers. Four drivers and four receivers allow multiple command and response paths without requiring separate interface ICs for every port. The 100 k BPS rate fits many instrument-control protocols that exchange short commands and measurements rather than sustained high-bandwidth data. Designers should preserve a common ground path between the board and connected RS-232 equipment, use a dedicated return conductor when practical, and place protection close to the external connector. The 24-pin PDIP format also suits instruments assembled with through-hole components and serviceable communication boards.
Recomendado
Security and Access Equipment
The ADM238LJNZ is applicable to security and access-control units that use RS-232 for configuration, diagnostics, or connection to existing access-control equipment. Its +5V CMOS operation matches embedded controller platforms, while the two complete channels can support separate command and status paths. The device's 100 k BPS capability is more than adequate for short configuration exchanges and supervisory protocols. Because these systems may be installed near motors, relays, or outdoor access hardware, the RS-232 connector should include appropriate transient protection and the board should maintain controlled return paths. A four-channel transceiver also allows channel sharing only when the connected protocol and electrical loading support that arrangement.
Recomendado
Barcode and Weighing Systems
The ADM238LJNZ fits barcode scanners, weighing indicators, and retail equipment that may expose several RS-232 ports for a scanner, display, or host computer. The four-driver, four-receiver arrangement consolidates two bidirectional interfaces while retaining a straightforward 24-pin PDIP layout for legacy controller boards. Its 100 k BPS rate comfortably covers typical scanner commands and short telemetry frames. Design the connector and cable interface for transient exposure, especially when cables leave an enclosure, and use a dedicated logic ground connection for reliable reference levels. The device's +5V requirement simplifies integration with embedded control boards that do not generate ±12V.
Recomendado
Embedded Serial Communication Hubs
The ADM238LJNZ can serve as the RS-232 interface stage of an embedded communication hub with two legacy ports. A microcontroller can use separate UART channels to route status, configuration, or peripheral traffic while the ADM238LJNZ handles the electrical conversion to EIA-232-E levels. The device operates from +5V, avoiding a bipolar line-driver supply in systems whose logic rail is already available. The 100 k BPS rate supports moderate-rate command traffic. Use the manufacturer's application circuit as the starting point, retain the specified bypass capacitors near the supply pins, and avoid routing connector-side outputs beneath noisy clock or switching-regulator areas.
Recomendado
Legacy Communication Adapters
The ADM238LJNZ is useful in legacy communication adapters designed to bridge modern logic boards to RS-232 equipment. Two complete channels can connect a host controller to two external devices while the transceiver converts between CMOS logic and RS-232 levels. Its 24-pin PDIP package is appropriate for adapter boards assembled with through-hole components and for repair or modernization programs involving older instruments. The +5V architecture reduces the adapter's power requirements compared with a ±12V interface. Designers should validate signal direction and grounding against the data sheet, add connector-side surge protection for exposed cables, and preserve adequate spacing between the RS-232 traces and sensitive analog or high-speed digital circuits.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADM238LJNZ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ADM238LJN |
|---|---|---|
| Product Type | +5V CMOS RS-232 transceiver | +5V CMOS RS-232 transceiver |
| Brand | Analog Devices | Analog Devices |
| Package | 24-PDIP | 24-PDIP |
| Number of Drivers | 4 | 4 |
| Number of Receivers | 4 | 4 |
| Supply Voltage | +5V | +5V |
| Maximum Data Rate | 100 k BPS | 100 k BPS |
| Supported Interface | EIA-232-E and V.28 | EIA-232-E and V.28 |
| Technology | CMOS | CMOS |
| Mounting Type | Through-hole | Through-hole |
| Ordering Suffix | ADM238LJNZ | ADM238LJN |
Diferenciadores clave
- Two complete RS-232 channels in one package (frente a MAX3221IPWR)
- Moderate-speed four-channel interface density (frente a MAX3221CDBR)
- Through-hole integration for legacy and industrial boards (frente a MAX3221CDBR)
Notas de diseño
Follow the bypass-capacitor placement and power-routing recommendations in the manufacturer application circuit. Place the supply capacitor close to the device's +5V and ground pins, use a low-impedance ground plane, and route connector-side driver and receiver nets away from clocks, inductors, and switching-converter nodes. RS-232 logic transitions can produce transient current, so uninterrupted return paths and short supply loops help prevent false resets or corrupted characters.
Do not assume every ADM238L suffix has identical environmental qualification. The ADM238LJNZ and ADM238LJN are listed as parametric substitutes, but the final ordering code must be checked against the required temperature range, package, and qualification status. Also verify channel direction during schematic capture: four drivers and four receivers can form two bidirectional ports only when the TX and RX connections are assigned correctly at the connector.
For cables that leave an enclosure, add suitable transient protection at the RS-232 connector and use a controlled signal-and-return path. RS-232 is unbalanced, so ground offsets and induced noise can affect receiver thresholds. Keep protection-device capacitance and leakage consistent with the 100 k BPS target, and connect the cable shield according to the complete installation and grounding strategy rather than treating it as an unconditional ground conductor.
Assign TX and RX nets directly from the 24-pin PDIP to their connector or protection network, and avoid unnecessary stubs through test pads. Maintain consistent impedance and spacing from unrelated digital or analog nets. If multiple RS-232 channels are used, keep their connector-side routing separated to minimize crosstalk, and provide filtering close to the connector when the attached cable is long or enters an electrically noisy environment.
Información de cumplimiento
AEC-Q100 is not applicable to this general-purpose RS-232 transceiver. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is identified in the referenced product information.