Analog Devices

ADM238LJNZ - 4/4 RS-232 Transceiver, 5V, 100k BPS | Analog Devices

부품 번호: ADM238LJNZ ✓ 활성
+5 V Vdss 24-pin PDIP Package
MOQ: 1 |

ADM238LJNZ 개요

The Analog Devices ADM238LJNZ is a low-power, +5V CMOS RS-232 transceiver with 4 drivers and 4 receivers, operating at up to 100 k BPS and housed in a 24-pin PDIP package. The device is intended for EIA-232-E and V.28 communications interfaces where a conventional ±12 V supply is unavailable. Its four-driver, four-receiver arrangement consolidates two full RS-232 channels into one package, making it useful for multi-port serial connectivity, industrial equipment, instrumentation, and embedded control systems.

An RS-232 transceiver is an interface integrated circuit that combines line drivers and line receivers. The driver converts TTL-compatible logic signals into RS-232-compatible levels, while the receiver converts incoming RS-232 signals back into logic levels. In the broader hierarchy, the ADM238LJNZ belongs to the interface IC family, specifically the RS-232 transceiver and communications-interface category. The 24-pin PDIP format supports through-hole assembly and straightforward panel or legacy industrial PCB layouts.

The ADM238L family is designed for low-power operation from a single +5V supply. The manufacturer identifies the device as a 5V CMOS RS-232 driver/receiver set with four drivers and four receivers. Its 100 k BPS communication rate is suitable for moderate-speed data links rather than high-speed synchronous or differential bus applications. The four-channel organization reduces the number of interface packages required when several RS-232 ports must share a common supply and ground architecture.

Typical uses include industrial controllers, barcode and weighing equipment, test systems, security equipment, and board-level communication links. Because the device operates from +5V, it can be placed between a modern microcontroller UART and an external RS-232 connector without requiring a separate bipolar supply. The logic-side interface remains compatible with the voltage levels used by the surrounding digital circuitry, while the line-side interface provides the voltage translation required by RS-232.

PCB implementation should preserve the manufacturer’s recommended decoupling arrangement and provide adequate copper and signal-return paths for the RS-232 connector. RS-232 is an unbalanced, point-to-point interface, so cable length, grounding, protection, and connector transients can influence reliability. Shielded or transient-protected cabling is appropriate when the port is exposed to industrial electrical noise. The manufacturer product page and ADM238L datasheet remain the primary references for pin assignment, electrical limits, and application-circuit details.

This page organizes the ADM238LJNZ specifications, package information, pricing references, pin-level application guidance, and available drop-in cross-reference information into an engineering-focused resource. It also identifies the principal design trade-offs between the ADM238LJNZ and other RS-232 transceiver options, helping designers select the interface device that best fits their voltage, throughput, packaging, and assembly requirements.

드롭인 대체품: ADM238LJNZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: ADM238LJNZ (동일 폼 팩터 및 풋프린트) — 차이점: Maximum Data Rate, Charge-Pump Capacitor, Package, Product Type, Supply Voltage.

Analog Devices
Maximum Data Rate: 120 kB/s
Charge-Pump Capacitor: 1 uF
Product Type: 4/4 full-duplex RS-232 transceiver
비교 대상: ADM238LJNZ →
Analog Devices
Maximum Data Rate: 120 kbps
Charge-Pump Capacitor: 1 μF
Package: 24-pin plastic DIP
비교 대상: ADM238LJNZ →
Analog Devices
Maximum Data Rate: 120 kB/s
Charge-Pump Capacitor: 1 F
Product Type: 4/4 full-duplex RS-232 transceiver
비교 대상: ADM238LJNZ →

ADM238LJN

✅ 드롭인
Analog Devices
📦 24-PDIP
4/4 full-duplex RS-232 transceiver · 5 V · 4 · 4 · 120 kB/s · 9 V · 1 F · Yes

가격 문의

데이터시트 보기 →

ADM238LJNZ 사양

Product Type RS-232 transceiver
Number of Drivers 4
Number of Receivers 4
공급 전압 +5 V
Maximum Data Rate 100 k BPS
Logic Compatibility CMOS
Supported Standard EIA-232-E and V.28
패키지 24-pin PDIP
실장 유형 Through-hole
Number of Interface Channels 4
Supply Type Single +5 V CMOS supply
Power Classification Low-power RS-232 transceiver

ADM238LJNZ 24-pin pdip 핀 구성 가이드

ADM238LJNZ(24-pin pdip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

ADM238LJNZ의 24-pin pdip 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: ADM238LJNZ.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

ADM238LJNZ 적합 용도: 6 애플리케이션s: Industrial Controller Serial Ports, Test and Measurement Equipment, Security and Access Equipment, Barcode and Weighing Systems, Embedded Serial Communication Hubs, Legacy Communication Adapters.

🏭

Industrial Controller Serial Ports

The ADM238LJNZ is well suited to industrial controllers that need more than one RS-232 connection while operating from a +5V logic supply. Its four drivers and four receivers implement two bidirectional RS-232 ports in one 24-pin PDIP device. The 100 k BPS maximum data rate is suitable for configuration links, service interfaces, and supervisory communication with peripheral equipment. A practical implementation places each transceiver channel near its connector, routes the RX and TX pairs as balanced signal-and-return paths, and keeps switching or high-current traces away from the interface lines. The single +5V supply simplifies the power tree compared with a traditional ±12V RS-232 design.

🔧

Test and Measurement Equipment

The ADM238LJNZ can provide two RS-232 links for test and measurement equipment that communicates with legacy instruments, fixture controllers, or service computers. Four drivers and four receivers allow multiple command and response paths without requiring separate interface ICs for every port. The 100 k BPS rate fits many instrument-control protocols that exchange short commands and measurements rather than sustained high-bandwidth data. Designers should preserve a common ground path between the board and connected RS-232 equipment, use a dedicated return conductor when practical, and place protection close to the external connector. The 24-pin PDIP format also suits instruments assembled with through-hole components and serviceable communication boards.

🔐

Security and Access Equipment

The ADM238LJNZ is applicable to security and access-control units that use RS-232 for configuration, diagnostics, or connection to existing access-control equipment. Its +5V CMOS operation matches embedded controller platforms, while the two complete channels can support separate command and status paths. The device's 100 k BPS capability is more than adequate for short configuration exchanges and supervisory protocols. Because these systems may be installed near motors, relays, or outdoor access hardware, the RS-232 connector should include appropriate transient protection and the board should maintain controlled return paths. A four-channel transceiver also allows channel sharing only when the connected protocol and electrical loading support that arrangement.

📦

Barcode and Weighing Systems

The ADM238LJNZ fits barcode scanners, weighing indicators, and retail equipment that may expose several RS-232 ports for a scanner, display, or host computer. The four-driver, four-receiver arrangement consolidates two bidirectional interfaces while retaining a straightforward 24-pin PDIP layout for legacy controller boards. Its 100 k BPS rate comfortably covers typical scanner commands and short telemetry frames. Design the connector and cable interface for transient exposure, especially when cables leave an enclosure, and use a dedicated logic ground connection for reliable reference levels. The device's +5V requirement simplifies integration with embedded control boards that do not generate ±12V.

🌐

Embedded Serial Communication Hubs

The ADM238LJNZ can serve as the RS-232 interface stage of an embedded communication hub with two legacy ports. A microcontroller can use separate UART channels to route status, configuration, or peripheral traffic while the ADM238LJNZ handles the electrical conversion to EIA-232-E levels. The device operates from +5V, avoiding a bipolar line-driver supply in systems whose logic rail is already available. The 100 k BPS rate supports moderate-rate command traffic. Use the manufacturer's application circuit as the starting point, retain the specified bypass capacitors near the supply pins, and avoid routing connector-side outputs beneath noisy clock or switching-regulator areas.

🖥️

Legacy Communication Adapters

The ADM238LJNZ is useful in legacy communication adapters designed to bridge modern logic boards to RS-232 equipment. Two complete channels can connect a host controller to two external devices while the transceiver converts between CMOS logic and RS-232 levels. Its 24-pin PDIP package is appropriate for adapter boards assembled with through-hole components and for repair or modernization programs involving older instruments. The +5V architecture reduces the adapter's power requirements compared with a ±12V interface. Designers should validate signal direction and grounding against the data sheet, add connector-side surge protection for exposed cables, and preserve adequate spacing between the RS-232 traces and sensitive analog or high-speed digital circuits.

What is the ADM238LJNZ?
The ADM238LJNZ is a +5V CMOS RS-232 transceiver from Analog Devices with 4 drivers and 4 receivers in a 24-pin PDIP package. According to the Analog Devices ADM238L product page, it is intended for EIA-232-E and V.28 communications interfaces where ±12V is not available. The device combines two full RS-232 channels in one through-hole package.
How many RS-232 channels does ADM238LJNZ provide?
The ADM238LJNZ provides four RS-232 drivers and four RS-232 receivers, corresponding to two complete bidirectional channels. Analog Devices describes the ADM238L family as a low-power +5V CMOS RS-232 transceiver with four drivers and four receivers. This channel density reduces the number of interface packages needed on a multi-port controller or industrial equipment board.
What is the maximum data rate of ADM238LJNZ?
The ADM238LJNZ supports data rates up to 100 k BPS. The Analog Devices ADM238L product page identifies the part as a 100 k BPS RS-232 transceiver, making it appropriate for moderate-speed serial links such as embedded controllers, test equipment, and industrial peripherals. Confirm the complete UART and cable timing budget in the manufacturer datasheet before choosing it for a particular bus.
What supply voltage does ADM238LJNZ require?
The ADM238LJNZ operates from a single +5V supply and uses CMOS-compatible logic. This is the central advantage described by Analog Devices: the interface can operate without a conventional ±12V RS-232 supply. The host microcontroller UART and the transceiver still require careful signal-level and grounding design, while the connector-side interface uses the RS-232 line levels.
Where can I download the ADM238LJNZ datasheet?
The official ADM238L product page provides the manufacturer data sheet and supporting documentation for the ADM238LJNZ. It is located at https://www.analog.com/en/products/adm238l.html. Use the manufacturer pin table and electrical characteristics when assigning connector signals, checking absolute maximum ratings, and selecting bypass capacitors.
Where can I find the ADM238LJNZ pinout?
The ADM238LJNZ pinout is documented in the ADM238L manufacturer data sheet available from the official product page. The target uses a 24-pin PDIP package, with pin 1 identified by the package marking convention. Use the pin-description table in the manufacturer datasheet when assigning each driver output, receiver input, supply, and ground connection.
What can replace the ADM238LJNZ?
The ADM238LJN is the closest documented drop-in alternative because it is the same Analog Devices ADM238L 24-pin PDIP interface family. Its four-driver, four-receiver arrangement and +5V RS-232 function align with the ADM238LJNZ. Verify the exact temperature grade and ordering information in the manufacturer datasheet before approving the substitution.
Is the ADM238LJNZ the same as the ADM238LJN?
The ADM238LJNZ and ADM238LJN are closely related ADM238L devices in the same 24-pin PDIP RS-232 transceiver family, but their order suffixes can identify different qualification or temperature variants. The documented substitute relationship supports drop-in consideration, but the manufacturer ordering table and full temperature specifications should be checked before production use.
When should I choose ADM238LJNZ over a single-channel RS-232 transceiver?
Choose the ADM238LJNZ when the design needs two complete RS-232 ports and can accept a 24-pin PDIP package. Its four drivers and four receivers provide more interface density than a one-channel device, while the +5V CMOS supply simplifies the power architecture. A smaller surface-mount transceiver may be preferable when only one port is needed or PCB area is critical.
Is ADM238LJNZ suitable for industrial RS-232 equipment?
The ADM238LJNZ is suitable for industrial equipment when its 100 k BPS rate, +5V operation, and 24-pin PDIP package match the system requirements. The ADM238L family supports EIA-232-E and V.28 interfaces. For industrial deployments, add suitable connector protection, maintain a low-impedance signal return, and verify the device temperature grade against the enclosure environment.
Where can I buy ADM238LJNZ online?
Use the “Request a Quote” form on this page to request ADM238LJNZ availability, commercial terms, and lead time. The form is the appropriate channel for current sourcing because stocked quantities and allocation can change quickly. Provide the required package variant, quantity, and target delivery location in the request.
What is the price of ADM238LJNZ?
Use the “Request a Quote” form on this page for the current ADM238LJNZ commercial offer. The form allows quantity, delivery, and sourcing conditions to be considered in one request instead of presenting a potentially stale standalone price. The structured listing references on this page are retained for traceability, but the quote form provides the current purchasing path.
What is the lead time for ADM238LJNZ?
Request the current ADM238LJNZ lead time through the “Request a Quote” form on this page. Lead time can vary with order quantity, manufacturing status, package allocation, and destination, so it should be confirmed for the intended production schedule. Include your requested quantity and required delivery date when submitting the request.
Is ADM238LJNZ in stock?
Current ADM238LJNZ inventory should be confirmed through the “Request a Quote” form on this page. Because stock levels and factory allocation can change rapidly, submit the required quantity and packaging preference for a current availability confirmation. The form can also capture any expected lead time for parts not immediately available.
What are the key specifications of ADM238LJNZ that engineers should know?
The ADM238LJNZ combines a +5V CMOS supply, 4 RS-232 drivers, 4 RS-232 receivers, and a maximum data rate of 100 k BPS in a 24-pin PDIP package. Analog Devices identifies support for EIA-232-E and V.28 interfaces and emphasizes operation where ±12V is unavailable. The device is therefore aimed at compact, multi-port, single-supply RS-232 designs.
What is the best Analog Devices equivalent for ADM238LJNZ?
The ADM238LJN is the best documented Analog Devices equivalent because it is listed as a parametric substitute and belongs to the same ADM238L 24-pin PDIP RS-232 transceiver family. The functional blocks and +5V interface concept match the ADM238LJNZ. Always confirm package pinout, temperature range, and device status against the manufacturer documentation before final substitution.

엔지니어링 참조 데이터: ADM238LJNZ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the ADM238LJNZ when the design requires two bidirectional RS-232 ports, a single +5V supply, and a 24-pin through-hole package. Its four drivers, four receivers, and 100 k BPS maximum data rate make it especially useful for industrial controllers, legacy adapters, and test equipment with multiple service or peripheral connections. Select the ADM238LJN as the documented same-family drop-in candidate, after checking the ordering suffix and temperature requirements against the manufacturer datasheet. Choose a single-channel MAX3221IPWR when only one port is needed and through-hole assembly is preferred, or a MAX3221CDBR when surface-mount construction and reduced board area are priorities. Do not substitute a surface-mount transceiver into a 24-pin PDIP footprint without redesigning the PCB and verifying the electrical and pin differences.

대체품과의 비교

파라미터 이 제품 ADM238LJN
Product Type +5V CMOS RS-232 transceiver +5V CMOS RS-232 transceiver
Brand Analog Devices Analog Devices
Package 24-PDIP 24-PDIP
Number of Drivers 4 4
Number of Receivers 4 4
Supply Voltage +5V +5V
Maximum Data Rate 100 k BPS 100 k BPS
Supported Interface EIA-232-E and V.28 EIA-232-E and V.28
Technology CMOS CMOS
Mounting Type Through-hole Through-hole
Ordering Suffix ADM238LJNZ ADM238LJN

주요 차별점

  • Two complete RS-232 channels in one package (vs MAX3221IPWR)
  • Moderate-speed four-channel interface density (vs MAX3221CDBR)
  • Through-hole integration for legacy and industrial boards (vs MAX3221CDBR)

설계 노트

Follow the bypass-capacitor placement and power-routing recommendations in the manufacturer application circuit. Place the supply capacitor close to the device's +5V and ground pins, use a low-impedance ground plane, and route connector-side driver and receiver nets away from clocks, inductors, and switching-converter nodes. RS-232 logic transitions can produce transient current, so uninterrupted return paths and short supply loops help prevent false resets or corrupted characters.

Do not assume every ADM238L suffix has identical environmental qualification. The ADM238LJNZ and ADM238LJN are listed as parametric substitutes, but the final ordering code must be checked against the required temperature range, package, and qualification status. Also verify channel direction during schematic capture: four drivers and four receivers can form two bidirectional ports only when the TX and RX connections are assigned correctly at the connector.

For cables that leave an enclosure, add suitable transient protection at the RS-232 connector and use a controlled signal-and-return path. RS-232 is unbalanced, so ground offsets and induced noise can affect receiver thresholds. Keep protection-device capacitance and leakage consistent with the 100 k BPS target, and connect the cable shield according to the complete installation and grounding strategy rather than treating it as an unconditional ground conductor.

Assign TX and RX nets directly from the 24-pin PDIP to their connector or protection network, and avoid unnecessary stubs through test pads. Maintain consistent impedance and spacing from unrelated digital or analog nets. If multiple RS-232 channels are used, keep their connector-side routing separated to minimize crosstalk, and provide filtering close to the connector when the attached cable is long or enters an electrically noisy environment.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

AEC-Q100 is not applicable to this general-purpose RS-232 transceiver. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration is identified in the referenced product information.

데이터 검증일: 2026-11-14 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

ADM238LJNZ datasheet ADM238LJNZ datasheet pdf ADM238LJNZ pinout ADM238LJNZ equivalent ADM238LJNZ replacement ADM238LJNZ cross reference ADM238LJNZ price ADM238LJNZ stock Analog Devices ADM238LJNZ ADM238LJNZ 24-PDIP ADM238LJNZ 100 k BPS ADM238LJNZ vs ADM238LJN ADM238LJNZ RS-232 interface IC ADM238LJNZ industrial controller

관련 부품 & 용어

Analog Devices ADM238LJNZ ADM238LJN ADM238L MAX3221IPWR MAX3221CDBR RS-232 transceiver RS-232 driver RS-232 receiver interface IC communication interface CMOS EIA-232-E V.28 100 k BPS +5V power supply 24-PDIP PDIP package family through-hole technology surface mount industrial automation test and measurement legacy serial communication transient protection embedded UART
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기