ADM239LAQ - 120 kbps RS-232 Interface | Analog Devices
N.º de pieza: ADM239LAQ ✓ ActivoADM239LAQ Descripción general
An RS-232 interface IC is a semiconductor that converts logic-level signals between a host or peripheral and the voltage levels used by the EIA-232-E serial bus. The ADM239LAQ combines CMOS transceivers, charge-pump converters, driver slew control, receiver threshold detection, and shutdown control in one integrated device. It sits between digital logic and the physical RS-232 connector.
Key features include operation from a single +5 V supply, support for 120 kbps data rates, TTL- and CMOS-compatible receiver thresholds, and low-power shutdown. The on-board DC-DC converters generate the elevated voltage required for RS-232 driver outputs. A 9 V output swing from the 5 V supply supports reliable communication over longer cable runs than a conventional ±5 V-compatible interface.
The receiver switching threshold is VCC/4, which is 1.25 V typical at a 5 V supply. Unused receiver inputs may remain unconnected because an internal 400 kΩ pull-up forces the corresponding output low. The EIA-232-E implementation also limits driver slew rate, helping control unwanted ringing and electromagnetic interference on connected cables.
Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale terminals, diagnostic interfaces, and embedded systems that need bidirectional RS-232 communication without an external negative supply. The device is particularly useful when equipment must combine several RS-232 ports with low-power standby operation on a single 5 V rail.
Designers should follow the manufacturer datasheet for external charge-pump capacitor selection, receiver and driver pin assignments, and unused-channel handling. Place the required capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog or high-speed digital circuits to minimize coupling.
This page combines the ADM239LAQ electrical characteristics, interface guidance, application fit, and verified sourcing information in one engineering-focused reference. It helps designers distinguish the device's integrated DC-DC architecture, 120 kbps capability, shutdown behavior, and 30 V receiver tolerance when planning an RS-232 interface.
Alternativas directas para ADM239LAQ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
ADM239LANZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ADM239LAQ Especificaciones
| Tensión de alimentación | +5 V |
| Velocidad de datos | 120 kbps |
| Driver and Receiver Configuration | 3 drivers and 3 receivers |
| RS-232 Output Swing | 9 V |
| External Charge-Pump Capacitors | 1 uF |
| Receiver Maximum Input Voltage | 30 V |
| Receiver Switching Threshold | VCC/4 |
| Nominal Receiver Switching Threshold at 5 V | 1.25 V typical |
| Input Logic Compatibility | TTL and CMOS compatible |
| Unused Input Pull-Up Resistance | 400 kΩ |
| Driver Slew Rate | Less than 30 V/ms |
| Power Shutdown | Low-power shutdown |
| Receivers Active During Shutdown | Yes |
| RS-232 Compliance | EIA-232-E and V.28 specifications |
| Power Conversion | On-board DC-DC converters |
| Encapsulado | CDIP-24 |
Guía de configuración de pines de ADM239LAQ cdip-24
Configuración de pines para ADM239LAQ (encapsulado cdip-24). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ADM239LAQ.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADM239LAQ es adecuado para 6 aplicacións: Industrial Serial Controllers, Test and Measurement Equipment, Point-of-Sale Terminals, Embedded Diagnostic Interfaces, Legacy Communication Port Expansion, Security and Access Systems.
Industrial Serial Controllers
The ADM239LAQ fits industrial equipment that must expose legacy RS-232 ports from a 5 V control board. Three drivers and three receivers provide six communication channels, while the integrated DC-DC converters produce an approximately 9 V driver swing without an external negative supply. Its 120 kbps rate is appropriate for configuration links, service consoles, and supervisory communications. The key design trade-off is that the CDIP-24 package occupies more board area than a compact surface-mount transceiver.
Recomendado
Test and Measurement Equipment
The ADM239LAQ is appropriate for test and measurement instruments that retain RS-232 control ports for legacy computers and service technicians. A single 5 V rail powers the interface, and the on-board converters avoid a separate negative rail for the three driver channels. Receiver inputs rated to 30 V improve tolerance to connected cable conditions. The 120 kbps limit supports terminal and control traffic rather than bulk instrument-data transfer.
Recomendado
Point-of-Sale Terminals
The ADM239LAQ can serve point-of-sale terminals requiring several RS-232 peripherals, such as scales, printers, or customer-display equipment. Its three transmitters and three receivers provide useful channel density within one ceramic DIP package, while 5 V-only operation simplifies the power architecture. Low-power shutdown supports systems that spend substantial time idle. Designers should treat the approximately 9 V output swing as a platform advantage over basic single-supply line drivers.
Recomendado
Embedded Diagnostic Interfaces
The ADM239LAQ is useful in embedded diagnostic equipment that communicates with service tools through an RS-232 port while maintaining a 5 V power budget. The receivers remain active during shutdown, allowing selected receive paths to continue monitoring where the system architecture requires it. The 30 V receiver-input rating improves robustness on connected diagnostic cables. A ceramic DIP format is appropriate for legacy repairability but requires careful connector placement and mechanical planning.
Recomendado
Legacy Communication Port Expansion
The ADM239LAQ can expand an embedded controller that retains one or more older RS-232 ports but has limited driver and receiver resources. Each device adds three driver outputs and three receiver inputs, all operating from the same 5 V supply as many embedded systems. Its 120 kbps rating is suitable for command and status traffic. The design trade-off is the relatively large CDIP-24 footprint compared with modern multichannel interface packages.
Recomendado
Security and Access Systems
The ADM239LAQ can support access-control panels, alarm controllers, and configuration links that use RS-232 as an auxiliary communication interface. Six transceiver channels allow multiple readers, supervisory terminals, or service interfaces to coexist, and the integrated converters remove the need for a separate negative supply. Shutdown behavior can reduce consumption in idle installations. Engineers should still verify cable length, ground strategy, and the 30 V receiver-input limit at the board interface.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADM239LAQ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Package | CDIP-24 |
| Brand | Analog Devices |
| Supply Voltage | +5 V |
| Data Rate | 120 kbps |
| Driver and Receiver Configuration | 3 drivers and 3 receivers |
| RS-232 Output Swing | 9 V |
| Receiver Maximum Input Voltage | 30 V |
| Receiver Switching Threshold | VCC/4, 1.25 V typical at 5 V |
| External Capacitor Value | 1 uF |
| Shutdown Capability | Low-power shutdown with receivers active |
Diferenciadores clave
- Three full-duplex RS-232 channels in one package (frente a MC1489NG4)
- Single-supply architecture with elevated driver swing (frente a MC1488NE4)
- Receive-side protection and shutdown flexibility (frente a MC1489NE4)
Notas de diseño
Place the 1 uF charge-pump capacitors close to the pins specified by the manufacturer datasheet and minimize loop area between each capacitor and its associated device pin. Keep the RS-232 driver and connector traces away from sensitive analog inputs and high-speed digital nets. A solid ground plane beneath the interface can improve return-path continuity, but connector ground and logic ground should be arranged to prevent large return currents from crossing sensitive signal paths.
The ADM239LAQ operates from a single +5 V supply and generates the elevated RS-232 output voltage internally. Follow the datasheet capacitor values and connection diagram rather than substituting generic charge-pump networks. Confirm that 5 V remains within the device's operating limits during startup and transient conditions. Because the driver can produce approximately 9 V swing, decouple the supply locally and keep the power-distribution path short to minimize switching-current excursions.
Do not treat an unused ADM239LAQ receiver input as mandatory to terminate if the circuit must remain in the documented inactive state. The internal 400 kΩ pull-up can force an unused input high and the corresponding output low, but leaving unused drivers unconnected requires different care because an undriven RS-232 output may create an uncontrolled interface state. Consult the pin-description table and explicitly configure every driver, receiver, supply, shutdown, and charge-pump connection.
Información de cumplimiento
The Analog Devices datasheet identifies EIA-232-E and V.28 specification compliance. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.