Analog Devices

ADM239LAQ - 120 kbps RS-232 Interface | Analog Devices

料号: ADM239LAQ ✓ 量产中
+5 V Vdss 400 kΩ Rds(on) CDIP-24 Package
最小起订量: 1 |

ADM239LAQ 概述

The Analog Devices ADM239LAQ is a +5 V powered CMOS RS-232 driver and receiver interface IC with a 120 kbps data rate, on-board DC-DC converters, and a 24-lead CDIP package. It supports three drivers and three receivers, provides approximately 9 V output swing from a 5 V supply, and accepts receiver inputs up to 30 V.

An RS-232 interface IC is a semiconductor that converts logic-level signals between a host or peripheral and the voltage levels used by the EIA-232-E serial bus. The ADM239LAQ combines CMOS transceivers, charge-pump converters, driver slew control, receiver threshold detection, and shutdown control in one integrated device. It sits between digital logic and the physical RS-232 connector.

Key features include operation from a single +5 V supply, support for 120 kbps data rates, TTL- and CMOS-compatible receiver thresholds, and low-power shutdown. The on-board DC-DC converters generate the elevated voltage required for RS-232 driver outputs. A 9 V output swing from the 5 V supply supports reliable communication over longer cable runs than a conventional ±5 V-compatible interface.

The receiver switching threshold is VCC/4, which is 1.25 V typical at a 5 V supply. Unused receiver inputs may remain unconnected because an internal 400 kΩ pull-up forces the corresponding output low. The EIA-232-E implementation also limits driver slew rate, helping control unwanted ringing and electromagnetic interference on connected cables.

Typical applications include industrial serial controllers, test and measurement equipment, point-of-sale terminals, diagnostic interfaces, and embedded systems that need bidirectional RS-232 communication without an external negative supply. The device is particularly useful when equipment must combine several RS-232 ports with low-power standby operation on a single 5 V rail.

Designers should follow the manufacturer datasheet for external charge-pump capacitor selection, receiver and driver pin assignments, and unused-channel handling. Place the required capacitors close to their associated pins and route the RS-232 connector interface away from sensitive analog or high-speed digital circuits to minimize coupling.

This page combines the ADM239LAQ electrical characteristics, interface guidance, application fit, and verified sourcing information in one engineering-focused reference. It helps designers distinguish the device's integrated DC-DC architecture, 120 kbps capability, shutdown behavior, and 30 V receiver tolerance when planning an RS-232 interface.

直接替换替代料: ADM239LAQ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

ADM239LANZ

✅ 直接替换
📦 24-pin package
Same 5 V supply, three drivers, three receivers, and 24-pin package; 0 V supply change and 0 channel-count change, while exact temperature-grade and qualification differences require datasheet confirmation

📋 参考替代料(不在目录中)

ADM239LAQ 规格参数

电源电压 +5 V
数据速率 120 kbps
Driver and Receiver Configuration 3 drivers and 3 receivers
RS-232 Output Swing 9 V
External Charge-Pump Capacitors 1 uF
Receiver Maximum Input Voltage 30 V
Receiver Switching Threshold VCC/4
Nominal Receiver Switching Threshold at 5 V 1.25 V typical
Input Logic Compatibility TTL and CMOS compatible
Unused Input Pull-Up Resistance 400 kΩ
Driver Slew Rate Less than 30 V/ms
Power Shutdown Low-power shutdown
Receivers Active During Shutdown Yes
RS-232 Compliance EIA-232-E and V.28 specifications
Power Conversion On-board DC-DC converters
封装 CDIP-24

ADM239LAQ cdip-24 引脚配置指南

ADM239LAQ(cdip-24 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

ADM239LAQ 的 cdip-24 封装引脚图

暂无详细引脚数据: ADM239LAQ.

请参阅 数据手册 以查看完整引脚配置。

典型应用

ADM239LAQ 适用于 6 应用s: Industrial Serial Controllers, Test and Measurement Equipment, Point-of-Sale Terminals, Embedded Diagnostic Interfaces, Legacy Communication Port Expansion, Security and Access Systems.

🏭

Industrial Serial Controllers

The ADM239LAQ fits industrial equipment that must expose legacy RS-232 ports from a 5 V control board. Three drivers and three receivers provide six communication channels, while the integrated DC-DC converters produce an approximately 9 V driver swing without an external negative supply. Its 120 kbps rate is appropriate for configuration links, service consoles, and supervisory communications. The key design trade-off is that the CDIP-24 package occupies more board area than a compact surface-mount transceiver.

🔧

Test and Measurement Equipment

The ADM239LAQ is appropriate for test and measurement instruments that retain RS-232 control ports for legacy computers and service technicians. A single 5 V rail powers the interface, and the on-board converters avoid a separate negative rail for the three driver channels. Receiver inputs rated to 30 V improve tolerance to connected cable conditions. The 120 kbps limit supports terminal and control traffic rather than bulk instrument-data transfer.

🖥️

Point-of-Sale Terminals

The ADM239LAQ can serve point-of-sale terminals requiring several RS-232 peripherals, such as scales, printers, or customer-display equipment. Its three transmitters and three receivers provide useful channel density within one ceramic DIP package, while 5 V-only operation simplifies the power architecture. Low-power shutdown supports systems that spend substantial time idle. Designers should treat the approximately 9 V output swing as a platform advantage over basic single-supply line drivers.

🔧

Embedded Diagnostic Interfaces

The ADM239LAQ is useful in embedded diagnostic equipment that communicates with service tools through an RS-232 port while maintaining a 5 V power budget. The receivers remain active during shutdown, allowing selected receive paths to continue monitoring where the system architecture requires it. The 30 V receiver-input rating improves robustness on connected diagnostic cables. A ceramic DIP format is appropriate for legacy repairability but requires careful connector placement and mechanical planning.

⚡

Legacy Communication Port Expansion

The ADM239LAQ can expand an embedded controller that retains one or more older RS-232 ports but has limited driver and receiver resources. Each device adds three driver outputs and three receiver inputs, all operating from the same 5 V supply as many embedded systems. Its 120 kbps rating is suitable for command and status traffic. The design trade-off is the relatively large CDIP-24 footprint compared with modern multichannel interface packages.

🧩

Security and Access Systems

The ADM239LAQ can support access-control panels, alarm controllers, and configuration links that use RS-232 as an auxiliary communication interface. Six transceiver channels allow multiple readers, supervisory terminals, or service interfaces to coexist, and the integrated converters remove the need for a separate negative supply. Shutdown behavior can reduce consumption in idle installations. Engineers should still verify cable length, ground strategy, and the 30 V receiver-input limit at the board interface.

What is the ADM239LAQ used for?
The ADM239LAQ is a +5 V powered CMOS RS-232 driver and receiver IC for bidirectional serial communication. It integrates three drivers, three receivers, and on-board DC-DC converters that generate elevated RS-232 output voltages from a single 5 V supply. According to the Analog Devices datasheet, it supports data rates up to 120 kbps and complies with EIA-232-E and V.28 specifications.
What are the key specifications of ADM239LAQ?
The ADM239LAQ provides three RS-232 drivers and three receivers, operates from +5 V, supports 120 kbps data rates, and delivers approximately 9 V output swing. Its receivers accept inputs up to 30 V and use a VCC/4 switching threshold, equivalent to 1.25 V typical at 5 V. These characteristics make it appropriate for multi-port industrial and embedded serial interfaces.
Where can I download the ADM239LAQ datasheet PDF?
The ADM239LAQ datasheet PDF can be accessed through the Analog Devices document link on this page or through the manufacturer-linked datasheet mirrors listed in the technical references. The manufacturer datasheet is the primary source for the pin-description table, external capacitor connections, shutdown behavior, electrical characteristics, and package drawings. Use the complete document when assigning every CDIP-24 connection.
Where can I find the ADM239LAQ pinout?
The ADM239LAQ pinout is defined by the pin-description table and package drawing in the Analog Devices datasheet. It is a 24-lead CDIP device containing three driver channels, three receiver channels, supply connections, shutdown control, and charge-pump capacitor nodes. Use the datasheet pin table when assigning PCB tracks because signal, power, and capacitor connections must follow the manufacturer's exact package orientation.
What is the ADM239LAQ receiver switching threshold?
The ADM239LAQ receiver switching threshold is VCC/4, producing a typical threshold of 1.25 V when VCC is 5 V. According to the Analog Devices datasheet, the receiver inputs are compatible with both TTL and CMOS logic levels. The threshold also ensures that an unused input is pulled high by the internal 400 kΩ resistor and forces the corresponding receiver output into a low state.
Does the ADM239LAQ need a negative supply?
No external negative supply is required for the ADM239LAQ. The device uses +5 V power and includes on-board DC-DC converters that develop the elevated voltage needed by the RS-232 driver outputs. According to the Analog Devices datasheet, the resulting output swing is approximately 9 V with a 5 V supply. This simplifies designs that would otherwise require a separate charge-pump supply network.
What is the maximum data rate of ADM239LAQ?
The ADM239LAQ supports RS-232 data rates up to 120 kbps. According to the Analog Devices datasheet, this device meets EIA-232-E and V.28 specifications while operating from a single +5 V supply. The 120 kbps capability suits legacy serial links, industrial controllers, configuration ports, and service interfaces rather than high-speed USB or Ethernet protocols.
Can the ADM239LAQ receivers remain active during shutdown?
Yes, the ADM239LAQ receivers remain active during shutdown. According to the Analog Devices datasheet, the shutdown function provides low-power operation while allowing receiver activity to continue. This feature can help a powered-down system monitor a remote RS-232 connection or preserve receive-side state, depending on the system architecture and external enable implementation.
What is the maximum receiver input voltage for ADM239LAQ?
The ADM239LAQ receiver input can withstand voltages up to 30 V. According to the Analog Devices datasheet, this provides tolerance for RS-232 signaling conditions and helps protect the receive path when connected to a remote cable. The 30 V rating is an absolute receiver-input limit and should not be confused with the approximately 9 V driver output swing generated by the device.
Where can I buy ADM239LAQ online?
Use the Request a Quote form on this page to request the current ADM239LAQ price, stock position, minimum order quantity, and lead time. The form routes the request through XAIPART's sales workflow and avoids publishing a price that may change without notice. For technical suitability, confirm the CDIP-24 package, 5 V supply, three-channel configuration, and operating-temperature requirements before ordering.
What is the price of ADM239LAQ?
The current ADM239LAQ price is provided through the Request a Quote form on this page. Submit the required quantity, target package preference, and delivery location to receive a current quotation and availability confirmation. This approach keeps the commercial response aligned with the requested quantity and avoids presenting a stale unit price that may not reflect available supply.
What is the lead time for ADM239LAQ?
Request the current ADM239LAQ lead time through the Request a Quote form on this page. Include your required quantity, shipment destination, and target date so procurement can confirm manufacturing or inventory availability for the CDIP-24 device. The ADM239LAQ is an older interface family with multiple channel counts, so schedule confirmation should be treated as part of the sourcing decision rather than assumed from a generic listing.
Is ADM239LAQ in stock?
Current ADM239LAQ inventory is best confirmed through the Request a Quote form on this page. Submit the required quantity and delivery region to obtain a stock and lead-time response from XAIPART. Because ceramic DIP inventory can move in smaller lots than surface-mount production quantities, confirm availability before committing the PCB assembly schedule.
What can replace ADM239LAQ?
The closest replacement must provide the same CDIP-24 footprint, three drivers, three receivers, 5 V operation, approximately 9 V driver swing, and at least 70% parametric proximity. The available cross-reference results identify ADM239LANZ and ADM239LJRZ-REEL as related family options, but their package suffixes indicate different physical packages. They therefore require footprint and pin verification rather than direct drop-in replacement.
Is ADM239LAQ suitable for industrial RS-232 equipment?
The ADM239LAQ is suitable for industrial RS-232 equipment when the design uses a 5 V supply, no more than 120 kbps, and up to three bidirectional serial channels. Its 30 V receiver-input tolerance, EIA-232-E and V.28 specification compliance, and shutdown capability support robust legacy interfaces. Confirm the operating-temperature rating and the ceramic DIP package before releasing a production design.

工程参考数据: ADM239LAQ ——对比、设计指导和合规信息。

选型指南

Choose the ADM239LAQ when a legacy system needs three RS-232 drivers and three receivers from one +5 V supply, especially when an approximately 9 V output swing is required and the board can accommodate a ceramic DIP-24 footprint. Its 120 kbps rate suits control, configuration, and service links rather than high-speed data transfer. The integrated converters and shutdown behavior simplify the power tree and can reduce external circuitry. MC1489NG4 or MC1489NE4 is preferable when only additional transmitters are needed and board area is constrained. MC1488NE4 may suit a simpler dedicated transmitter design, but it does not combine the ADM239LAQ's three transmitters, three receivers, and shutdown receiver feature. No verified drop-in replacement was identified because the related ADM239 family suffix options use different package configurations; verify the footprint and pin assignments before considering any substitution.

与替代料对比

参数 本产品
Package CDIP-24
Brand Analog Devices
Supply Voltage +5 V
Data Rate 120 kbps
Driver and Receiver Configuration 3 drivers and 3 receivers
RS-232 Output Swing 9 V
Receiver Maximum Input Voltage 30 V
Receiver Switching Threshold VCC/4, 1.25 V typical at 5 V
External Capacitor Value 1 uF
Shutdown Capability Low-power shutdown with receivers active

关键差异点

  • Three full-duplex RS-232 channels in one package (对比 MC1489NG4)
  • Single-supply architecture with elevated driver swing (对比 MC1488NE4)
  • Receive-side protection and shutdown flexibility (对比 MC1489NE4)

设计说明

Place the 1 uF charge-pump capacitors close to the pins specified by the manufacturer datasheet and minimize loop area between each capacitor and its associated device pin. Keep the RS-232 driver and connector traces away from sensitive analog inputs and high-speed digital nets. A solid ground plane beneath the interface can improve return-path continuity, but connector ground and logic ground should be arranged to prevent large return currents from crossing sensitive signal paths.

The ADM239LAQ operates from a single +5 V supply and generates the elevated RS-232 output voltage internally. Follow the datasheet capacitor values and connection diagram rather than substituting generic charge-pump networks. Confirm that 5 V remains within the device's operating limits during startup and transient conditions. Because the driver can produce approximately 9 V swing, decouple the supply locally and keep the power-distribution path short to minimize switching-current excursions.

Do not treat an unused ADM239LAQ receiver input as mandatory to terminate if the circuit must remain in the documented inactive state. The internal 400 kΩ pull-up can force an unused input high and the corresponding output low, but leaving unused drivers unconnected requires different care because an undriven RS-232 output may create an uncontrolled interface state. Consult the pin-description table and explicitly configure every driver, receiver, supply, shutdown, and charge-pump connection.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The Analog Devices datasheet identifies EIA-232-E and V.28 specification compliance. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.

数据核验日期: 2026-11-09 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

ADM239LAQ datasheet ADM239LAQ pinout ADM239LAQ datasheet pdf ADM239LAQ CDIP-24 pinout ADM239LAQ equivalent ADM239LAQ replacement ADM239LAQ cross reference ADM239LAQ application circuit ADM239LAQ price ADM239LAQ stock Analog Devices ADM239LAQ ADM239LAQ 120 kbps RS-232 ADM239LAQ 5 V RS-232 interface ADM239LAQ shutdown receivers

相关元器件 & 术语

Analog Devices ADM239LAQ ADM239LANZ ADM239LJRZ-REEL RS-232 RS-232 transceiver CMOS interface IC driver receiver EIA-232-E V.28 TTL-compatible logic CMOS-compatible logic DC-DC converter charge-pump capacitor 120 kbps 30 V receiver input CDIP-24 ceramic dual in-line package surface-mount alternative comparison low-power shutdown industrial serial interface test and measurement equipment point-of-sale terminal
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情