Microchip Technology

AT90CAN64-15MT1 - 15MHz AVR CAN MCU | Microchip Technology

N.º de pieza: AT90CAN64-15MT1 ✓ Activo
3.3 V to 5 V Vdss 64-QFN, 9 x 9 mm Package 15 MHz Speed 64 KB Memory
MOQ: 1 |

AT90CAN64-15MT1 Descripción general

The Microchip Technology AT90CAN64-15MT1 is an 8-bit AVR RISC microcontroller with a 15 MHz operating clock, 64 KB of flash memory and an integrated CAN controller, housed in a 64-QFN 9x9 mm package. It is designed for embedded control systems that require deterministic CAN communication, compact PCB area and low-power CMOS operation.

An 8-bit microcontroller is a programmable semiconductor that executes embedded firmware while integrating memory, I/O, timers and communication peripherals onto one device. The AT90CAN64 belongs to the hierarchy of AVR microcontrollers, 8-bit RISC processors, embedded processors and semiconductor components. Its integrated CAN controller makes it suitable for distributed industrial, transportation and control networks where a dedicated external CAN transceiver would otherwise be required.

The AT90CAN64-15MT1 provides 64 KB of flash, 4 KB of SRAM, 2 KB of EEPROM, 53 general-purpose I/O lines and 32 general-purpose working registers. The manufacturer identifies the family as an AVR enhanced RISC architecture capable of executing instructions in a single clock cycle. This combination provides useful processing headroom for protocol handling, supervisory logic, data acquisition and local control functions.

CAN support is the principal system-level benefit. The controller supports frame transmission, reception, filtering and fault handling, while external transceiver circuitry converts the controller's logic-level signals into the physical CAN bus waveform. Integrating the controller alongside the AVR core reduces board area and simplifies firmware organization compared with a discrete processor and CAN interface.

Typical uses include industrial supervisory controllers, automotive and transportation modules, building automation nodes, remote instrumentation, CAN-connected sensors and compact embedded gateways. A 15 MHz clock provides sufficient throughput for many control tasks while keeping the device in the low-power 8-bit MCU class. Designs should still verify timing margins under the highest CAN bus load and the worst-case firmware execution path.

PCB implementation requires careful treatment of the 64-QFN footprint, exposed thermal pad, power and ground distribution, clock stability and CAN transceiver signal integrity. Keep the CAN bus and differential routing away from high-current switching nodes, provide the decoupling and bulk capacitance recommended by the manufacturer, and use a continuous ground plane where practical. Confirm the exposed-pad solder and assembly requirements for the selected manufacturing process.

This page combines manufacturer specifications, package details, engineering guidance and clearly qualified drop-in alternatives to support component selection, PCB planning and sourcing. It also distinguishes confirmed electrical differences involving clock speed, memory capacity and device density so engineers can validate each substitution against the original design requirements.

Alternativas directas para AT90CAN64-15MT1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con AT90CAN64-15MT1 (mismo factor de forma y huella) — difiere en Package, CAN Controller, EEPROM, Product Type, SRAM.

Microchip Technology
Package: 64-pin QFN (9 mm x 9 mm)
CAN Controller: CAN 2.0A / 2.0B compliant
EEPROM: 4 KB
Comparar con AT90CAN64-15MT1 →
Microchip Technology
Package: 64-QFN (9 x 9 mm)
CAN Controller: CAN 2.0A and CAN 2.0B
EEPROM: 1 KB
Comparar con AT90CAN64-15MT1 →
Microchip Technology
Package: 64-lead TQFP, 14 mm x 14 mm
Comparar con AT90CAN64-15MT1 →
Microchip Technology
Package: 64-pin TQFP, 14 mm x 14 mm
CAN Controller: CAN 2.0A and CAN 2.0B compliant
Comparar con AT90CAN64-15MT1 →
Microchip Technology
Product Type: 8-bit RISC Flash Microcontroller
Comparar con AT90CAN64-15MT1 →

AT90CAN64-15MU

✅ Sustitución directa
📦 64-QFN (9x9 mm)
Same 15 MHz clock and 64-QFN pin count; ordering-suffix and packing details must be verified before release

📋 Alternativa de referencia (no en el catálogo)

AT90CAN64-16MU

✅ Sustitución directa
Microchip Technology
📦 64-QFN (9x9 mm)
8-bit RISC Flash Microcontroller · AVR enhanced RISC · 8 bit · 16 MHz · 64 KB · 64K x 8 bits · 2 KB · 4 KB

Consulte el precio

Ver hoja de datos →

AT90CAN128-15MU

✅ Sustitución directa
📦 64-QFN (9x9 mm)
Flash capacity increases from 64 KB to 128 KB, a 100% increase; the maximum clock remains 15 MHz

📋 Alternativa de referencia (no en el catálogo)

AT90CAN128-16MU

✅ Sustitución directa
Microchip Technology
📦 64-QFN (9x9 mm)
AVR 8-bit RISC · 128 KB (128K x 8) · 4 KB · 4 KB · 16 MHz · 4.5 V to 5.5 V · 53 · 32

Consulte el precio

Ver hoja de datos →

AT90CAN32-16MUR

✅ Sustitución directa
Microchip Technology
📦 64-QFN (9x9 mm)
8-bit RISC Flash Microcontroller with CAN Controller · AVR Enhanced RISC · 8 bit · 16 MHz · 32 KB (32K x 8) · 1 KB · 2 KB · 53

Consulte el precio

Ver hoja de datos →

AT90CAN64-15MT1 Valores máximos y características eléctricas

Product Type 8-bit AVR RISC microcontroller with CAN controller
Frecuencia de reloj máxima 15 MHz
Flash Memory 64 KB
SRAM 4 KB
EEPROM 2 KB
General-Purpose I/O Lines 53
General-Purpose Working Registers 32
CAN Controller 1 integrated CAN controller
Operating Voltage 3.3 V to 5 V
Encapsulado 64-QFN, 9 x 9 mm
Tipo de montaje Surface mount
Architecture AVR enhanced RISC
Programmable Flash 64 KB
Instruction Throughput Approaching 1 MIPS per MHz

Guía de configuración de pines de AT90CAN64-15MT1 64-qfn, 9 x 9 mm

Configuración de pines para AT90CAN64-15MT1 (encapsulado 64-qfn, 9 x 9 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.

Diagrama de patillaje del encapsulado 64-qfn, 9 x 9 mm para AT90CAN64-15MT1

No hay datos detallados de patillaje disponibles para AT90CAN64-15MT1.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

AT90CAN64-15MT1 es adecuado para 6 aplicacións: Industrial CAN Supervisory Controller, Building Automation and HVAC Node, Automotive CAN Gateway Module, CAN-Connected Sensor Aggregator, Transportation and Telemetry Module, Remote Instrumentation Controller.

🏭

Industrial CAN Supervisory Controller

The AT90CAN64-15MT1 fits industrial supervisory nodes that monitor machine conditions and exchange commands over a CAN bus. Its 15 MHz AVR core provides timing headroom for protocol servicing, local state machines and diagnostic handling, while 64 KB of flash accommodates application firmware and 4 KB of SRAM supports working buffers. The integrated CAN controller reduces board area by combining protocol processing with the embedded control core. In a typical design, the MCU interfaces to a 3.3 V or 5 V CAN transceiver, reads sensor and switch inputs through its I/O lines, and publishes process state to other nodes. Validate worst-case interrupt latency and bus timing under peak network traffic, and provide local filtering so unrelated CAN frames do not consume unnecessary processor time.

🏠

Building Automation and HVAC Node

The AT90CAN64-15MT1 is suitable for building-automation nodes that combine equipment control with CAN-based building communication. Its 64 KB of flash can hold protocol handlers, configuration data and application logic, while 53 general-purpose I/O lines support digital inputs, outputs and status indicators. The microcontroller can manage relay or valve commands, monitor sensors and report faults through the integrated CAN controller. Using the MCU beside a compatible transceiver reduces the component count compared with a separate communications controller. For HVAC equipment, confirm the exact operating-temperature grade, use the appropriate watchdog and brownout strategy, and schedule actuator outputs so a reset cannot create unsafe equipment states.

🚗

Automotive CAN Gateway Module

The AT90CAN64-15MT1 can serve as the local control element in a compact automotive CAN gateway or body-network interface. Its 15 MHz AVR architecture, 64 KB of flash and integrated CAN controller are suited to translating messages, supervising actuators and maintaining diagnostic state. The device operates from a 3.3 V or 5 V core rail, but the complete automotive module still needs a suitably rated transceiver, input protection and power conditioning. Verify the exact automotive qualification and temperature variant before deployment because qualification is not established by the ordering name alone. Keep the differential CAN routing short and isolated from motor-drive switching nodes, and include fault counters, watchdog recovery and safe-state behavior in the firmware design.

🧩

CAN-Connected Sensor Aggregator

The AT90CAN64-15MT1 is appropriate for an aggregator that collects readings from multiple CAN-connected sensors and presents a consolidated result to a higher-level controller. Its 53 general-purpose I/O lines support discrete sensors, status inputs and local alarms, while the CAN controller handles network reception and transmission. The 15 MHz clock permits efficient filtering and formatting of routine sensor traffic without requiring a larger processor. Use the device's SRAM and EEPROM for working state and configuration, and account for CAN bus termination only where physically required by the network topology. For battery-powered deployments, disable unused peripherals and define a low-power wake strategy, but ensure that the selected transceiver and external circuitry do not dominate the standby current.

📡

Transportation and Telemetry Module

The AT90CAN64-15MT1 supports compact transportation telemetry modules that collect operating data and transmit status through a CAN network. Its 64 KB of flash is suitable for event logging, parameter configuration and communication routines, while 4 KB of SRAM provides room for packet assembly and local buffering. The microcontroller can monitor switches, sensors or subsystem status and convert those inputs into CAN frames for a vehicle or rail controller. Implement timeout handling for missing frames, validation of received identifiers and controlled output states after reset or bus failure. Because transportation environments may experience large transients and ground offsets, use a transceiver and protection network rated for the installation and verify the complete power path independently of the MCU's core supply tolerance.

🔧

Remote Instrumentation Controller

The AT90CAN64-15MT1 can act as a remote instrumentation controller in laboratory, process or field-service equipment. The 15 MHz AVR core supports measurement sequencing, local calculations, calibration handling and command parsing, while the integrated CAN controller provides deterministic communication with a host or distributed instrument network. Its 64 KB of flash offers room for protocol and application code, and the 53 I/O lines can support digital measurement channels, front-panel indicators and control outputs. Keep analog front-end circuitry separate from the MCU supply and ground paths, and use the manufacturer's pin descriptions to assign ADC, comparator and communication functions. Firmware should include range checks, sensor timeout logic and a controlled recovery path for communication or calibration faults.

What is the AT90CAN64-15MT1?
The AT90CAN64-15MT1 is a Microchip Technology 8-bit AVR RISC microcontroller with a 15 MHz clock, 64 KB of flash and an integrated CAN controller. According to the Microchip AT90CAN64 product page, the family provides 4 KB of SRAM, 2 KB of EEPROM, 53 general-purpose I/O lines and 32 working registers. It is packaged in a compact 64-QFN 9x9 mm surface-mount package for CAN-connected embedded systems.
What are the key specifications of AT90CAN64-15MT1 that engineers should know?
The AT90CAN64-15MT1 combines a 15 MHz AVR enhanced RISC core with 64 KB of flash, 4 KB of SRAM, 2 KB of EEPROM and 53 general-purpose I/O lines. According to the Microchip AT90CAN64 product page, the controller includes CAN communication capability and 32 general-purpose working registers. The package is a 64-QFN measuring 9 x 9 mm, with 3.3 V and 5 V operating support.
Where can I download the AT90CAN64-15MT1 datasheet?
The AT90CAN64 datasheet is available through the official Microchip AT90CAN64 product page at https://www.microchip.com/en-us/product/AT90CAN64. That page is the appropriate starting point for the complete pin description, electrical characteristics, memory map, timing diagrams, CAN controller information and package drawings. Use the manufacturer documentation when assigning PCB signals or validating operating limits.
Where can I find the AT90CAN64-15MT1 pinout?
The AT90CAN64-15MT1 pinout is published in the pin-description and package-drawing sections of the Microchip AT90CAN64 manufacturer documentation. The device uses a 64-QFN 9x9 mm package with an exposed pad. Follow the numbered pin table and recommended footprint exactly, because the exposed thermal pad also requires the appropriate land pattern and solder process.
What can replace the AT90CAN64-15MT1?
The closest drop-in candidates are the Microchip AT90CAN64-15MU, AT90CAN64-16MU, AT90CAN128-15MU and AT90CAN128-16MU, all identified in the same 64-pin QFN family. The AT90CAN64-15MU offers the closest functional match, while the -16MU variants increase the clock from 15 MHz to 16 MHz. AT90CAN128 alternatives increase flash capacity, so firmware, memory assumptions and pin-level requirements must be reviewed before substitution.
Is AT90CAN64-15MT1 the same as AT90CAN64-16MU?
No, AT90CAN64-15MT1 and AT90CAN64-16MU are related drop-in devices but are not electrically identical. The AT90CAN64-15MT1 operates at up to 15 MHz, while the AT90CAN64-16MU operates at up to 16 MHz, a 6.7% clock increase. The increase can improve timing margin, although maximum clock assumptions and bus timing calculations in the original design must be reassessed.
AT90CAN64-15MT1 vs AT90CAN64-15MU - which is better for a new design?
Choose the AT90CAN64-15MT1 when the required design point is explicitly 15 MHz and the 64-QFN arrangement matches the PCB. The AT90CAN64-15MU is a closely related option for a 64-pin QFN design requiring the same AT90CAN64 family functionality. For either selection, confirm the exact ordering suffix, temperature grade, packing form and lifecycle status against the manufacturer documentation before releasing the BOM.
When should I choose AT90CAN64-15MT1 over AT90CAN128-16MU?
Choose the AT90CAN64-15MT1 when the design is sized around a 15 MHz AVR core and 64 KB of flash. The AT90CAN128-16MU provides 128 KB of flash and a 16 MHz maximum clock, so it offers more memory headroom and 6.7% more clock capability while using the related 64-QFN family arrangement. Select it only after confirming that the additional density does not change the required peripheral or memory-map assumptions.
Is AT90CAN64-15MT1 suitable for industrial CAN controller applications?
The AT90CAN64-15MT1 is suitable for compact CAN-based supervisory and control applications that fit within 64 KB of flash and a 15 MHz AVR core. Its integrated CAN controller reduces the need for a separate CAN protocol device. For industrial deployment, verify the exact temperature grade, operating-voltage range, EMC requirements, transceiver choice and isolation needs for the installation environment.
What is the best Microchip equivalent for AT90CAN64-15MT1?
The AT90CAN64-15MU is the closest same-family candidate identified for the AT90CAN64-15MT1, using the related 64-QFN format and retaining the 15 MHz class. The AT90CAN64-16MU offers a 6.7% higher clock, while AT90CAN128-15MU and AT90CAN128-16MU increase flash capacity to 128 KB. Confirm pin compatibility, memory requirements and production status in the manufacturer cross-reference documentation before substitution.
How much current does the AT90CAN64-15MT1 require?
The AT90CAN64-15MT1 supply-current value depends on operating mode, clock frequency, voltage, CAN activity and enabled peripherals, so a single operating-current figure should not be assumed. According to the Microchip AT90CAN64 manufacturer documentation, the electrical characteristics section distinguishes active, idle and power-down conditions. Use the relevant mode and voltage from that table when designing the regulator and CAN-transceiver power budget.
Does the AT90CAN64-15MT1 need an external CAN transceiver?
The AT90CAN64-15MT1 contains a CAN controller, but the controller does not directly drive a physical CAN bus. A compatible CAN transceiver is required to convert the MCU's logic-level TX and RX signals into the differential CAN_H and CAN_L bus signals. The transceiver should be selected for the intended CAN version, bus speed, supply voltage, isolation, ESD protection and automotive or industrial environment.
How should the AT90CAN64-15MT1 CAN bus be routed?
Route CAN_H and CAN_L as a closely coupled differential pair with continuous reference to a ground plane, while minimizing stubs, vias and parallel high-current paths. Place the CAN transceiver near the connector or bus interface, and keep switching regulators, inductors and fast digital clocks away from the differential pair. Add the protection and common-mode components recommended by the transceiver supplier for the installation environment.
Is AT90CAN64-15MT1 in stock and what is its lead time?
Current inventory and lead time for the AT90CAN64-15MT1 are not established by the manufacturer product information. Use the Request a Quote form on this page to request current availability, minimum order quantity, scheduled delivery and the exact packing suffix required by your assembly process. This avoids relying on stale stock information and allows the quote to reflect the production schedule.
How can I buy AT90CAN64-15MT1 and check its price?
Use the Request a Quote form on this page to request the current unit price, quantity breaks, stock position, lead time and packaging for the AT90CAN64-15MT1. Include your required order quantity, reel or tray preference, target date and approved manufacturing documentation. The quote workflow provides a current commercial response for the exact ordering suffix without embedding stale price figures in technical content.
What power-management and decoupling practices apply to AT90CAN64-15MT1?
Place the manufacturer-recommended bypass capacitance at the supply pins and connect the 64-QFN exposed pad to the appropriate ground or thermal land pattern. The CAN transceiver and MCU should be assigned deliberate regulator headroom for their combined active and transient loads. Estimate worst-case dissipation from the actual clock, peripheral activity and bus loading rather than relying only on idle current when selecting the supply.

Datos de referencia de ingeniería para AT90CAN64-15MT1 — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Select the AT90CAN64-15MT1 when the design is explicitly based on a 15 MHz AVR controller with 64 KB of flash and a 64-QFN footprint. The AT90CAN64-15MU is the closest related choice when an equivalent ordering configuration is required, but its suffix, temperature grade and packing must be confirmed. Use the AT90CAN64-16MU when the additional 6.7% clock capability is useful and all timing assumptions can be revalidated. Choose AT90CAN128-15MU or AT90CAN128-16MU when larger firmware images justify the doubled flash capacity. AT90CAN32-16MUR is appropriate only when 32 KB of flash is sufficient, because it halves the target memory. Before substituting any device, verify pin compatibility, peripheral resources, memory-map behavior, temperature grade, packing form and lifecycle status against the manufacturer documentation.

Comparación con alternativas

Parámetro Este producto AT90CAN64-15MU AT90CAN64-16MU AT90CAN128-15MU AT90CAN128-16MU AT90CAN32-16MUR
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 64-QFN (9x9 mm) 64-QFN (9x9 mm) 64-QFN (9x9 mm) 64-QFN (9x9 mm) 64-QFN (9x9 mm) 64-QFN (9x9 mm)
Maximum Clock Frequency 15 MHz 15 MHz 16 MHz 15 MHz 16 MHz 16 MHz
Flash Memory 64 KB 64 KB 64 KB 128 KB 128 KB 32 KB
CAN Controller Integrated Integrated Integrated Integrated Integrated Integrated
Architecture AVR enhanced RISC AVR enhanced RISC AVR enhanced RISC AVR enhanced RISC AVR enhanced RISC AVR enhanced RISC

Diferenciadores clave

  • Closest same-family 64-QFN alternative (frente a AT90CAN64-15MU)
  • Higher clock alternative with related architecture (frente a AT90CAN64-16MU)
  • Memory expansion path in the same 64-QFN family (frente a AT90CAN128-15MU)
  • Combined clock and memory expansion (frente a AT90CAN128-16MU)

Notas de diseño

Route the AT90CAN64-15MT1 power connections directly to the pins specified by the manufacturer, placing high-frequency bypass capacitance immediately at the device. The 64-QFN footprint is compact and requires careful assembly planning, including a suitable exposed-pad solder pattern and thermal-via strategy. Verify the package drawing and land pattern rather than scaling the 9 x 9 mm body dimensions independently.

Treat CAN_H and CAN_L as a controlled-impedance differential pair routed over a continuous ground plane. Minimize stubs and layer transitions, avoid parallel routing with switching-power paths, and place the transceiver close to the connector or protection devices. Add common-mode and surge protection appropriate to the installation, then verify timing and radiated-emissions performance on the final board because the MCU package and ground return can affect bus symmetry.

Estimate the complete power budget from the MCU operating mode, clock activity, enabled peripherals, I/O loading and CAN transceiver current rather than from one nominal MCU current value. At 15 MHz and 5 V, even a modest current increase produces meaningful supply power, so provide regulator headroom for transient bus activity and startup. Keep high-current return paths out of the MCU ground region and follow the manufacturer's decoupling and exposed-pad guidance.

Do not treat the MCU CAN controller as a complete physical-bus interface; a compatible transceiver, protection network and termination arrangement are still required. Also avoid assuming that a related -MU or 16 MHz part is automatically interchangeable. Check the exact suffix, package drawing, temperature grade, memory capacity, clock-dependent timing assumptions, boot behavior and firmware support before releasing a substitution.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Compliance claims require confirmation from the current Microchip product documentation or a declaration for the exact ordering suffix. No compliance certificate or standard designation is established in the manufacturer page excerpt.

Búsquedas relacionadas

at90can64 datasheet atmel at90can64 AT90CAN64-15MT1 datasheet AT90CAN64-15MT1 pinout AT90CAN64-15MT1 datasheet pdf AT90CAN64-15MT1 equivalent AT90CAN64-15MT1 replacement AT90CAN64-15MT1 cross reference AT90CAN64-15MT1 vs AT90CAN64-16MU AT90CAN64-15MT1 footprint AT90CAN64-15MT1 CAN controller AT90CAN64-15MT1 application circuit AT90CAN64-15MT1 price AT90CAN64-15MT1 stock

Componentes & términos relacionados

Microchip Technology AT90CAN64-15MT1 AT90CAN64 AT90CAN64-15MU AT90CAN64-16MU AT90CAN128-15MU AT90CAN128-16MU AT90CAN32-16MUR AVR enhanced RISC 8-bit microcontroller embedded microcontroller CAN controller CAN transceiver 64-QFN QFN package family surface-mount package 15 MHz clock 64 KB flash memory 4 KB SRAM 2 KB EEPROM industrial automation automotive networking building automation remote instrumentation
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ