AT90CAN64-15MT1 - 15MHz AVR CAN MCU | Microchip Technology
부품 번호: AT90CAN64-15MT1 ✓ 활성AT90CAN64-15MT1 개요
An 8-bit microcontroller is a programmable semiconductor that executes embedded firmware while integrating memory, I/O, timers and communication peripherals onto one device. The AT90CAN64 belongs to the hierarchy of AVR microcontrollers, 8-bit RISC processors, embedded processors and semiconductor components. Its integrated CAN controller makes it suitable for distributed industrial, transportation and control networks where a dedicated external CAN transceiver would otherwise be required.
The AT90CAN64-15MT1 provides 64 KB of flash, 4 KB of SRAM, 2 KB of EEPROM, 53 general-purpose I/O lines and 32 general-purpose working registers. The manufacturer identifies the family as an AVR enhanced RISC architecture capable of executing instructions in a single clock cycle. This combination provides useful processing headroom for protocol handling, supervisory logic, data acquisition and local control functions.
CAN support is the principal system-level benefit. The controller supports frame transmission, reception, filtering and fault handling, while external transceiver circuitry converts the controller's logic-level signals into the physical CAN bus waveform. Integrating the controller alongside the AVR core reduces board area and simplifies firmware organization compared with a discrete processor and CAN interface.
Typical uses include industrial supervisory controllers, automotive and transportation modules, building automation nodes, remote instrumentation, CAN-connected sensors and compact embedded gateways. A 15 MHz clock provides sufficient throughput for many control tasks while keeping the device in the low-power 8-bit MCU class. Designs should still verify timing margins under the highest CAN bus load and the worst-case firmware execution path.
PCB implementation requires careful treatment of the 64-QFN footprint, exposed thermal pad, power and ground distribution, clock stability and CAN transceiver signal integrity. Keep the CAN bus and differential routing away from high-current switching nodes, provide the decoupling and bulk capacitance recommended by the manufacturer, and use a continuous ground plane where practical. Confirm the exposed-pad solder and assembly requirements for the selected manufacturing process.
This page combines manufacturer specifications, package details, engineering guidance and clearly qualified drop-in alternatives to support component selection, PCB planning and sourcing. It also distinguishes confirmed electrical differences involving clock speed, memory capacity and device density so engineers can validate each substitution against the original design requirements.
드롭인 대체품: AT90CAN64-15MT1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AT90CAN64-15MT1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, CAN Controller, EEPROM, Product Type, SRAM.
AT90CAN64-15MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT90CAN64-16MU
✅ 드롭인가격 문의
데이터시트 보기 →AT90CAN128-15MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT90CAN128-16MU
✅ 드롭인가격 문의
데이터시트 보기 →AT90CAN32-16MUR
✅ 드롭인가격 문의
데이터시트 보기 →AT90CAN64-15MT1 최대 정격 & 전기적 특성
| Product Type | 8-bit AVR RISC microcontroller with CAN controller |
| 최대 클록 주파수 | 15 MHz |
| Flash Memory | 64 KB |
| SRAM | 4 KB |
| EEPROM | 2 KB |
| General-Purpose I/O Lines | 53 |
| General-Purpose Working Registers | 32 |
| CAN Controller | 1 integrated CAN controller |
| Operating Voltage | 3.3 V to 5 V |
| 패키지 | 64-QFN, 9 x 9 mm |
| 실장 유형 | Surface mount |
| Architecture | AVR enhanced RISC |
| Programmable Flash | 64 KB |
| Instruction Throughput | Approaching 1 MIPS per MHz |
AT90CAN64-15MT1 64-qfn, 9 x 9 mm 핀 구성 가이드
AT90CAN64-15MT1(64-qfn, 9 x 9 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AT90CAN64-15MT1.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AT90CAN64-15MT1 적합 용도: 6 애플리케이션s: Industrial CAN Supervisory Controller, Building Automation and HVAC Node, Automotive CAN Gateway Module, CAN-Connected Sensor Aggregator, Transportation and Telemetry Module, Remote Instrumentation Controller.
Industrial CAN Supervisory Controller
The AT90CAN64-15MT1 fits industrial supervisory nodes that monitor machine conditions and exchange commands over a CAN bus. Its 15 MHz AVR core provides timing headroom for protocol servicing, local state machines and diagnostic handling, while 64 KB of flash accommodates application firmware and 4 KB of SRAM supports working buffers. The integrated CAN controller reduces board area by combining protocol processing with the embedded control core. In a typical design, the MCU interfaces to a 3.3 V or 5 V CAN transceiver, reads sensor and switch inputs through its I/O lines, and publishes process state to other nodes. Validate worst-case interrupt latency and bus timing under peak network traffic, and provide local filtering so unrelated CAN frames do not consume unnecessary processor time.
추천
Building Automation and HVAC Node
The AT90CAN64-15MT1 is suitable for building-automation nodes that combine equipment control with CAN-based building communication. Its 64 KB of flash can hold protocol handlers, configuration data and application logic, while 53 general-purpose I/O lines support digital inputs, outputs and status indicators. The microcontroller can manage relay or valve commands, monitor sensors and report faults through the integrated CAN controller. Using the MCU beside a compatible transceiver reduces the component count compared with a separate communications controller. For HVAC equipment, confirm the exact operating-temperature grade, use the appropriate watchdog and brownout strategy, and schedule actuator outputs so a reset cannot create unsafe equipment states.
추천
Automotive CAN Gateway Module
The AT90CAN64-15MT1 can serve as the local control element in a compact automotive CAN gateway or body-network interface. Its 15 MHz AVR architecture, 64 KB of flash and integrated CAN controller are suited to translating messages, supervising actuators and maintaining diagnostic state. The device operates from a 3.3 V or 5 V core rail, but the complete automotive module still needs a suitably rated transceiver, input protection and power conditioning. Verify the exact automotive qualification and temperature variant before deployment because qualification is not established by the ordering name alone. Keep the differential CAN routing short and isolated from motor-drive switching nodes, and include fault counters, watchdog recovery and safe-state behavior in the firmware design.
추천
CAN-Connected Sensor Aggregator
The AT90CAN64-15MT1 is appropriate for an aggregator that collects readings from multiple CAN-connected sensors and presents a consolidated result to a higher-level controller. Its 53 general-purpose I/O lines support discrete sensors, status inputs and local alarms, while the CAN controller handles network reception and transmission. The 15 MHz clock permits efficient filtering and formatting of routine sensor traffic without requiring a larger processor. Use the device's SRAM and EEPROM for working state and configuration, and account for CAN bus termination only where physically required by the network topology. For battery-powered deployments, disable unused peripherals and define a low-power wake strategy, but ensure that the selected transceiver and external circuitry do not dominate the standby current.
추천
Transportation and Telemetry Module
The AT90CAN64-15MT1 supports compact transportation telemetry modules that collect operating data and transmit status through a CAN network. Its 64 KB of flash is suitable for event logging, parameter configuration and communication routines, while 4 KB of SRAM provides room for packet assembly and local buffering. The microcontroller can monitor switches, sensors or subsystem status and convert those inputs into CAN frames for a vehicle or rail controller. Implement timeout handling for missing frames, validation of received identifiers and controlled output states after reset or bus failure. Because transportation environments may experience large transients and ground offsets, use a transceiver and protection network rated for the installation and verify the complete power path independently of the MCU's core supply tolerance.
추천
Remote Instrumentation Controller
The AT90CAN64-15MT1 can act as a remote instrumentation controller in laboratory, process or field-service equipment. The 15 MHz AVR core supports measurement sequencing, local calculations, calibration handling and command parsing, while the integrated CAN controller provides deterministic communication with a host or distributed instrument network. Its 64 KB of flash offers room for protocol and application code, and the 53 I/O lines can support digital measurement channels, front-panel indicators and control outputs. Keep analog front-end circuitry separate from the MCU supply and ground paths, and use the manufacturer's pin descriptions to assign ADC, comparator and communication functions. Firmware should include range checks, sensor timeout logic and a controlled recovery path for communication or calibration faults.
추천
추천 제품 요약
엔지니어링 참조 데이터: AT90CAN64-15MT1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AT90CAN64-15MU | AT90CAN64-16MU | AT90CAN128-15MU | AT90CAN128-16MU | AT90CAN32-16MUR |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) |
| Maximum Clock Frequency | 15 MHz | 15 MHz | 16 MHz | 15 MHz | 16 MHz | 16 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 128 KB | 128 KB | 32 KB |
| CAN Controller | Integrated | Integrated | Integrated | Integrated | Integrated | Integrated |
| Architecture | AVR enhanced RISC | AVR enhanced RISC | AVR enhanced RISC | AVR enhanced RISC | AVR enhanced RISC | AVR enhanced RISC |
주요 차별점
- Closest same-family 64-QFN alternative (vs AT90CAN64-15MU)
- Higher clock alternative with related architecture (vs AT90CAN64-16MU)
- Memory expansion path in the same 64-QFN family (vs AT90CAN128-15MU)
- Combined clock and memory expansion (vs AT90CAN128-16MU)
설계 노트
Route the AT90CAN64-15MT1 power connections directly to the pins specified by the manufacturer, placing high-frequency bypass capacitance immediately at the device. The 64-QFN footprint is compact and requires careful assembly planning, including a suitable exposed-pad solder pattern and thermal-via strategy. Verify the package drawing and land pattern rather than scaling the 9 x 9 mm body dimensions independently.
Treat CAN_H and CAN_L as a controlled-impedance differential pair routed over a continuous ground plane. Minimize stubs and layer transitions, avoid parallel routing with switching-power paths, and place the transceiver close to the connector or protection devices. Add common-mode and surge protection appropriate to the installation, then verify timing and radiated-emissions performance on the final board because the MCU package and ground return can affect bus symmetry.
Estimate the complete power budget from the MCU operating mode, clock activity, enabled peripherals, I/O loading and CAN transceiver current rather than from one nominal MCU current value. At 15 MHz and 5 V, even a modest current increase produces meaningful supply power, so provide regulator headroom for transient bus activity and startup. Keep high-current return paths out of the MCU ground region and follow the manufacturer's decoupling and exposed-pad guidance.
Do not treat the MCU CAN controller as a complete physical-bus interface; a compatible transceiver, protection network and termination arrangement are still required. Also avoid assuming that a related -MU or 16 MHz part is automatically interchangeable. Check the exact suffix, package drawing, temperature grade, memory capacity, clock-dependent timing assumptions, boot behavior and firmware support before releasing a substitution.
규정 준수 정보
Compliance claims require confirmation from the current Microchip product documentation or a declaration for the exact ordering suffix. No compliance certificate or standard designation is established in the manufacturer page excerpt.