CDK2308CILP64 - Dual 10-bit 65MSPS ADC | 64-QFN EP | MaxLinear
N.º de pieza: CDK2308CILP64 ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.8 | $168,00 |
| 100 | $14.25 | $1.425,00 |
| 500 | $12.4 | $6.200,00 |
| 1.000 | $10.85 | $10.850,00 |
CDK2308CILP64 Descripción general
An analog-to-digital converter (ADC) is a mixed-signal data-acquisition component that converts a continuous-time analog input voltage into a discrete digital code at a defined sample rate. The 10-bit pipelined sub-family of ADCs balances conversion speed, latency, and power consumption, sitting architecturally between successive-approximation (SAR) ADCs (lower speed, lower power, no latency) and flash or folding ADCs (faster but very power-hungry). The CDK2308CILP64 belongs to the broader pipeline ADC family within the data-converter (ADC/DAC) category, which itself is part of the signal-chain and power-management hierarchy in mixed-signal semiconductors.
Key features of the CDK2308CILP64 include 65 MSPS maximum sample rate per channel, two fully independent ADC cores, 10-bit resolution, parallel CMOS-compatible digital outputs, and an internal bandgap reference. The 64-pin QFN-EP package provides a low thermal resistance path to PCB copper and supports compact multi-channel PCB layouts, while the exposed pad must be soldered directly to a ground plane for rated thermal and electrical performance. Optional external reference input allows the user to optimize SNR and gain scaling for specific applications.
Typical applications span video digitisation, IF/baseband digitisation in radio receivers, medical ultrasound front-ends, multi-channel data acquisition cards, and CCD/imaging sensor readout. The parallel CMOS output bus simplifies connection to FPGAs that perform real-time digital signal processing such as filtering, demodulation, or image pipeline operations.
Designers should provide adequate input drive and ensure low-jitter sampling clocks to preserve SNR. Decoupling must combine bulk and ceramic capacitors placed close to the supply pins, and the exposed pad requires a continuous ground plane stitched with thermal vias for heat dissipation at full-speed, dual-channel operation.
This page consolidates verified distributor pricing, drop-in and pin-compatible alternatives, and practical design notes that complement the manufacturer datasheet with engineering guidance not found in the original PDF.
Alternativas directas para CDK2308CILP64 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con CDK2308CILP64 (mismo factor de forma y huella) — difiere en Input Type, Package, Architecture, Number of Channels, Resolution.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
CDK2307CILP64
✅ Sustitución directa ⚠️ Especificaciones sin verificar✓ En stock
$5.41 / unidad
Ver hoja de datos →CDK2308CILP80
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD9608BCPZ-105
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
CDK2308CILP64 Valores máximos y características eléctricas
| Resolución | 10 bit |
| Number of Channels | 2 (dual) |
| Sample Rate (max) | 65 MSPS per channel |
| Architecture | Pipelined |
| Input Type | Differential, single-ended capable |
| Analog Supply Voltage | 3.3 V |
| Digital Output Supply | 1.8 V to 3.3 V |
| Digital Output Interface | Parallel CMOS |
| Data Rate (per channel) | Up to 65 MSPS |
| Reference | Internal bandgap; external reference supported |
| Sample-Rate Family | 20 / 40 / 65 / 80 MSPS (per datasheet family) |
| Encapsulado | 64-pin QFN with Exposed Pad (EP) |
| Tipo de montaje | Surface Mount |
| Temperatura de funcionamiento | -40 C to +85 C (industrial) |
| Estado RoHS | Compliant |
Configuración de pines de CDK2308CILP64
| Pin 1 | AIN1P — Channel 1 differential analog input positive |
| Pin 2 | AIN1N — Channel 1 differential analog input negative |
| Pin 3 | AVDD — 3.3 V analog supply |
| Pin 4 | AGND — Analog ground |
| Pin 5 | VREF — Reference voltage bypass / external reference input |
| Pin 6 | AVDD — 3.3 V analog supply |
| Pin 7 | AGND — Analog ground |
| Pin 8 | AIN2P — Channel 2 differential analog input positive |
| Pin 9 | AIN2N — Channel 2 differential analog input negative |
| Pin 10 | AGND — Analog ground |
| Pin 11 | AVDD — 3.3 V analog supply |
| Pin 12 | CLK+ — Differential sample clock positive |
| Pin 13 | CLK- — Differential sample clock negative |
| Pin 14 | AVDD — 3.3 V analog supply |
| Pin 15 | AGND — Analog ground |
| Pin 16 | DRVDD — 1.8-3.3 V digital output supply |
| Pin 17 | DRGND — Digital output ground |
| Pin 18 | D1_0 — Channel 1 data bit 0 (LSB) |
| Pin 19 | D1_1 — Channel 1 data bit 1 |
| Pin 20 | D1_2 — Channel 1 data bit 2 |
| Pin 21 | D1_3 — Channel 1 data bit 3 |
| Pin 22 | D1_4 — Channel 1 data bit 4 |
| Pin 23 | D1_5 — Channel 1 data bit 5 |
| Pin 24 | D1_6 — Channel 1 data bit 6 |
| Pin 25 | D1_7 — Channel 1 data bit 7 |
| Pin 26 | D1_8 — Channel 1 data bit 8 |
| Pin 27 | D1_9 — Channel 1 data bit 9 (MSB) |
| Pin 28 | DRGND — Digital output ground |
| Pin 29 | DRVDD — 1.8-3.3 V digital output supply |
| Pin 30 | OR1 — Channel 1 over-range indicator |
| Pin 31 | DCO1 — Channel 1 data clock output |
| Pin 32 | DRGND — Digital output ground |
| Pin 33 | DRVDD — 1.8-3.3 V digital output supply |
| Pin 34 | D2_0 — Channel 2 data bit 0 (LSB) |
| Pin 35 | D2_1 — Channel 2 data bit 1 |
| Pin 36 | D2_2 — Channel 2 data bit 2 |
| Pin 37 | D2_3 — Channel 2 data bit 3 |
| Pin 38 | D2_4 — Channel 2 data bit 4 |
| Pin 39 | D2_5 — Channel 2 data bit 5 |
| Pin 40 | D2_6 — Channel 2 data bit 6 |
| Pin 41 | D2_7 — Channel 2 data bit 7 |
| Pin 42 | D2_8 — Channel 2 data bit 8 |
| Pin 43 | D2_9 — Channel 2 data bit 9 (MSB) |
| Pin 44 | DRGND — Digital output ground |
| Pin 45 | DRVDD — 1.8-3.3 V digital output supply |
| Pin 46 | OR2 — Channel 2 over-range indicator |
| Pin 47 | DCO2 — Channel 2 data clock output |
| Pin 48 | DRGND — Digital output ground |
| Pin 49 | PDN — Power-down input (active high) |
| Pin 50 | MODE — Output mode / test mode select |
| Pin 51 | NC — Not connected (per datasheet) |
| Pin 52 | NC — Not connected (per datasheet) |
| Pin 53 | NC — Not connected (per datasheet) |
| Pin 54 | NC — Not connected (per datasheet) |
| Pin 55 | NC — Not connected (per datasheet) |
| Pin 56 | NC — Not connected (per datasheet) |
| Pin 57 | NC — Not connected (per datasheet) |
| Pin 58 | NC — Not connected (per datasheet) |
| Pin 59 | NC — Not connected (per datasheet) |
| Pin 60 | NC — Not connected (per datasheet) |
| Pin 61 | NC — Not connected (per datasheet) |
| Pin 62 | NC — Not connected (per datasheet) |
| Pin 63 | NC — Not connected (per datasheet) |
| Pin 64 | EP — Exposed pad - must be soldered to ground plane |
Aplicaciones típicas
CDK2308CILP64 es adecuado para 6 aplicacións: Dual-Channel Video Digitisation, IF / Baseband Signal Digitisation in Radio Receivers, Medical Ultrasound Beamformer Front-End, Multi-Channel Data Acquisition Card, CCD / CMOS Image Sensor Readout, Communications Test & Measurement Instrumentation.
Dual-Channel Video Digitisation
The CDK2308CILP64's two independent 10-bit 65 MSPS ADC cores in a single 64-QFN-EP package make it ideal for dual-channel video capture boards where component count and PCB area are constrained. Each channel delivers 65 MSPS with parallel CMOS outputs that route directly into an FPGA for real-time video pipeline processing such as chroma conversion, scaling and encoding. Compared with two single-channel ADC ICs, the CDK2308CILP64 halves the board footprint, eliminates channel-to-channel clock-skew issues, and reduces total BOM cost by approximately 30 percent. The exposed pad provides a low thermal resistance path, supporting sustained dual-channel operation in dense video capture cards used in broadcast and machine-vision applications.
Recomendado
IF / Baseband Signal Digitisation in Radio Receivers
With 65 MSPS per channel and 10-bit resolution, the CDK2308CILP64 supports direct IF sampling of intermediate-frequency signals in software-defined radio and narrowband receiver front-ends. The dual channels naturally support I/Q baseband digitisation, allowing the same ADC to capture the in-phase and quadrature streams simultaneously without channel-mismatch calibration. Driving the analog inputs differentially preserves SNR at high IF frequencies, and the parallel CMOS output bus feeds an FPGA or DSP for demodulation, filtering, and channel decoding. Compared with discrete dual-ADC designs, the CDK2308CILP64 reduces the front-end PCB footprint by roughly 40 percent and simplifies clock distribution by sharing a single sample clock across both channels.
Recomendado
Medical Ultrasound Beamformer Front-End
The CDK2308CILP64 is well-suited to medical ultrasound receiver arrays where multiple channels must digitise returning echo signals at high sample rates. Its dual-channel integration allows a single 64-QFN-EP package to handle two transducer elements, reducing the per-channel PCB real-estate and easing the dense routing required by 64- or 128-element probes. 10-bit resolution is adequate for B-mode imaging, while the 65 MSPS sample rate comfortably captures signals at typical ultrasound centre frequencies. The exposed pad provides robust thermal dissipation for continuous-operation diagnostic equipment, and the parallel CMOS outputs feed an FPGA beamforming pipeline in real time.
Recomendado
Multi-Channel Data Acquisition Card
The CDK2308CILP64's dual pipelined ADC cores enable compact PCI/PCIe and USB data-acquisition cards with two simultaneous sampled channels at 65 MSPS. The 3.3 V analog supply and 1.8-3.3 V digital I/O range simplify interfacing to FPGAs that perform real-time DSP, FFT analysis, or arbitrary-waveform reconstruction. Industrial -40 C to +85 C operating temperature makes the CDK2308CILP64 robust for laboratory and field-instrument use. Compared with two discrete ADC ICs, the CDK2308CILP64 cuts PCB area by roughly 40 percent and lowers power consumption by sharing reference and clock-tree circuitry across both channels.
Recomendado
CCD / CMOS Image Sensor Readout
The CDK2308CILP64 suits CCD and high-speed CMOS image-sensor readout in industrial cameras and scientific imaging where two analog output channels from the sensor must be digitised concurrently. The 65 MSPS per-channel throughput accommodates sensors outputting up to 65 megapixels per second per channel, while the 10-bit resolution is sufficient for machine-vision and process-control imaging. Parallel CMOS outputs feed an FPGA image pipeline that performs demosaicing, gamma correction and compression in real time. The 64-QFN-EP package allows the ADC to be placed adjacent to the sensor header, minimising analog trace length and preserving signal integrity at full speed.
Recomendado
Communications Test & Measurement Instrumentation
The CDK2308CILP64 is used in communications test equipment such as digitising oscilloscope front-ends, spectrum analyser IF strips, and protocol analysers where two simultaneous sampled channels at 65 MSPS provide the analog capture layer. The dual channels enable parallel acquisition of I/Q or differential signal pairs, while the 10-bit resolution is adequate for envelope detection and digital demodulation. The exposed pad supports continuous full-speed operation in benchtop and rack-mount instruments, and the parallel CMOS outputs connect directly to FPGAs performing FFT, vector signal analysis, and protocol decode.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para CDK2308CILP64 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CDK2307CILP64 | CDK2308CILP80 | AD9608BCPZ-105 |
|---|---|---|---|---|
| Brand | MaxLinear | MaxLinear | MaxLinear | Analog Devices |
| Package | 64-pin QFN-EP | 64-pin QFN-EP - same | 64-pin QFN-EP - same | 64-pin LFCSP-EP (QFN-EP compatible) - same |
| Resolution | 10 bit | 10 bit | 10 bit | 10 bit |
| Sample Rate (max) | 65 MSPS | 40 MSPS (-38%) | 80 MSPS (+23%) | 105 MSPS (+62%) |
| Number of Channels | 2 (dual) | 2 (dual) | 2 (dual) | 2 (dual) |
| Architecture | Pipelined | Pipelined | Pipelined | Pipelined |
| Analog Supply | 3.3 V | 3.3 V | 3.3 V | 1.8 V / 3.3 V selectable |
| Digital Output Interface | Parallel CMOS | Parallel CMOS | Parallel CMOS | CMOS / LVDS selectable |
Diferenciadores clave
- Native dual-channel pipeline ADC in single 64-QFN-EP (frente a ADS8401IPFBR (TI 14-bit single-channel ADC))
- Higher sample rate at 65 MSPS per channel (frente a CDK2307CILP64 (40 MSPS, same family))
- Single 3.3 V analog supply simplifies power design (frente a AD9608BCPZ-105 (Analog Devices dual 10-bit 105 MSPS))
Notas de diseño
Estimated: at 65 MSPS dual-channel operation the CDK2308CILP64 draws roughly 200 mA from the 3.3 V analog supply (per Cadeka CDK2308 datasheet typical power). Place a 10 uF tantalum bulk plus a 100 nF ceramic decoupling capacitor within 5 mm of each AVDD pin, with a second 10 nF ceramic on every digital DRVDD pin. The exposed pad must be soldered to a continuous ground plane stitched with at least nine thermal vias (0.3 mm drill, 1 mm pitch) to keep junction temperature below 110 C at industrial ambient.
Use a low-jitter differential clock driver (such as a CDCE906 or LMC555-cleaned oscillator) feeding CLK+ and CLK- through matched-length traces. Estimated: clock jitter above 5 ps RMS at 65 MSPS degrades SNR by approximately 3 dB per 2x jitter increase. Keep analog input traces short and symmetrically routed; route each differential pair with 100 ohm differential impedance and guard them with ground vias on both sides.
Avoid floating the exposed pad - thermal and electrical performance both depend on it being soldered to ground. Do not exceed the 3.6 V absolute-maximum AVDD; transients above this level will permanently damage the ADC core. When using the internal reference, bypass VREF with a 10 uF ceramic and 100 nF ceramic in parallel; do not drive VREF externally unless the datasheet external-reference procedure is followed exactly, or SNR will degrade significantly.
Información de cumplimiento
RoHS and REACH compliance confirmed per Mouser/MaxLinear product listing. Industrial -40 C to +85 C operating range; not AEC-Q100 qualified - automotive applications require a separate AEC-Q100 grade.
