Infineon

CY7C65211-24LTXIT - USB Serial Bridge | Infineon

N.º de pieza: CY7C65211-24LTXIT ✓ Activo
24-QFN, 4 x 4 mm Package
MOQ: 1 |

CY7C65211-24LTXIT Descripción general

The Infineon CY7C65211-24LTXIT is a full-speed USB 2.0 serial bridge controller supporting UART, I2C, and SPI in a 24-QFN 4 x 4 mm package. It delivers UART operation up to 3 Mbps and I2C operation up to 400 kHz, while integrating CapSense, general-purpose GPIO, and battery-charging detection compliant with USB Battery Charging Specification revision 1.2.

A USB-serial bridge is a USB interface controller that allows a legacy serial peripheral to communicate with a host computer over USB. The CY7C65211 belongs to the EZ-USB family of USB interface controllers and sits between a USB connector and an embedded UART, I2C, or SPI peripheral. This bridge role places the controller within the broader interface-controller and power-management ecosystem for compact industrial, medical, and consumer equipment.

The controller combines three selectable serial interfaces in one device, reducing the need for separate USB-to-UART, USB-to-I2C, and USB-to-SPI bridge components. Its 3 Mbps UART capability supports faster data links than many conventional USB-UART converters, while 400 kHz I2C operation addresses standard-mode peripheral buses. CapSense extends the device beyond basic serial conversion, and USB 2.0 battery-charging detection supports portable designs that require downstream-device charging awareness.

The CY7C65211 family uses an internal microcontroller-based architecture with configurable USB and serial interfaces. Because the USB side operates at full speed, the device is intended for control and data-transfer applications rather than high-bandwidth storage. GPIO and CapSense functions provide additional control or touch-input capability without requiring separate devices. Exact operating voltage, clock architecture, memory configuration, and pin-level electrical limits must be confirmed in the manufacturer datasheet before a new design is released.

Typical uses include configuring legacy serial equipment through USB, connecting sensor boards that communicate over I2C, programming SPI peripherals, and adding touch sensing to USB-controlled panels. The same mixed-interface capability is useful in compact instruments where board area is limited and a single controller must service more than one peripheral type. Firmware and host-side driver support should be evaluated early because interface configuration and enumeration behavior depend on the selected application architecture.

Layout planning should reserve a solid USB connection, regulated supply, ground reference, decoupling network, and accessible test points. Keep the USB differential pair impedance-controlled and minimize stub branches, especially when the bridge is placed behind cables or connectors. Firmware configuration, peripheral-side I/O levels, and pin multiplexing must be reconciled with the board netlist because incorrect mode selection can route signals to unintended pins.

This product overview combines the manufacturer interface capabilities, package information, ordering variants, and cross-reference findings with practical guidance for USB-to-serial integration. It also distinguishes verified pin-compatible device-family options from package variants that should not be treated as drop-in replacements without a full footprint and temperature-grade review.

Alternativas directas para CY7C65211-24LTXIT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con CY7C65211-24LTXIT (mismo factor de forma y huella) — difiere en Package, Supported Serial Interfaces.

Infineon
Package: 24-QFN (4x4 mm)
Supported Serial Interfaces: UART, I2C, SPI
Comparar con CY7C65211-24LTXIT →

CY7C65211A-24LTXIT

✅ Sustitución directa
📦 24-QFN (4 x 4 mm)
Device-family A revision; 0 Mbps UART-rate difference and 0 kHz I2C-rate difference versus CY7C65211-24LTXIT

📋 Alternativa de referencia (no en el catálogo)

CY7C65211-24LTXIT Especificaciones

Device Type Full-speed USB serial bridge controller
USB Specification USB 2.0 full-speed
Supported Serial Interfaces UART, I2C, and SPI
Maximum UART Data Rate 3 Mbps
Maximum I2C Data Rate 400 kHz
Number of Serial Channels 1 channel
Integrated Peripheral CapSense touch-sensing controller
Battery Charging Detection USB Battery Charging Specification revision 1.2
GPIO Support General-purpose GPIO
Encapsulado 24-QFN, 4 x 4 mm
Tipo de montaje Surface mount
Operating Temperature Grade Industrial grade
Estado RoHS Compliant
Moisture Sensitivity Level MSL 3

Guía de configuración de pines de CY7C65211-24LTXIT 24-qfn, 4 x 4 mm

Configuración de pines para CY7C65211-24LTXIT (encapsulado 24-qfn, 4 x 4 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 24-qfn, 4 x 4 mm para CY7C65211-24LTXIT

No hay datos detallados de patillaje disponibles para CY7C65211-24LTXIT.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

CY7C65211-24LTXIT es adecuado para 6 aplicacións: USB-to-Serial Test Equipment, Industrial Sensor Gateway, Medical Device Connectivity, SPI Peripheral Programmer, USB-Enabled Control Panel, USB Battery-Charging Detection.

🔧

USB-to-Serial Test Equipment

The CY7C65211-24LTXIT fits test fixtures that need one USB port to communicate with legacy UART, I2C, or SPI instrumentation. Its UART rate of up to 3 Mbps supports faster command and data transfers than many low-speed serial bridges, while I2C operation up to 400 kHz accommodates common sensor and EEPROM buses. The 24-QFN 4 x 4 mm footprint helps keep interface density high in compact fixtures. Firmware must select the correct serial mode and implement the expected command protocol before production testing begins.

🏭

Industrial Sensor Gateway

For industrial sensor gateways, the CY7C65211-24LTXIT can connect a USB host to sensors or controllers using UART, I2C, or SPI. The single-channel architecture is useful when a gateway needs a configurable peripheral interface rather than three simultaneous protocol converters. Its 400 kHz I2C capability supports standard-mode devices, while 3 Mbps UART enables higher-rate legacy links. GPIO provides additional control signaling, and the compact 24-QFN package preserves board area for sensing and isolation components.

💊

Medical Device Connectivity

The CY7C65211-24LTXIT can serve as the USB interface in medical equipment that communicates with a serial accessory, sensor module, or service port. UART, I2C, and SPI support permits reuse across multiple product variants, while GPIO can handle auxiliary device-control signals. CapSense can add touch controls without a separate sensing controller. The industrial-grade ordering option supports industrial temperature environments, but medical suitability still depends on system-level electrical validation, risk assessment, and the applicable product requirements.

💻

SPI Peripheral Programmer

The CY7C65211-24LTXIT is appropriate for a compact SPI programmer that connects a legacy programming fixture to a USB host. Its single serial channel can be configured for SPI, allowing firmware to handle programming clocks, commands, and status signaling. USB full-speed operation fits the low-to-moderate bandwidth of many device-programming workflows, while GPIO can assist fixture control. The 4 x 4 mm 24-QFN package is especially useful where the connector, level conversion, and target-device circuitry compete for limited board area.

🧩

USB-Enabled Control Panel

The CY7C65211-24LTXIT can bridge a USB host to a control panel containing UART, I2C, or SPI peripherals. CapSense adds touch-detection capability for keys, sliders, or proximity controls, while GPIO supports indicators, interlocks, or discrete inputs. Using one controller for data and touch functions can reduce component count in a space-constrained panel. The mixed-protocol capability is valuable during product development because different panel variants can use the same controller family, although firmware configuration must ensure that each peripheral is assigned to the correct interface.

📱

USB Battery-Charging Detection

The CY7C65211-24LTXIT integrates battery-charging detection compliant with revision 1.2 of the USB Battery Charging Specification, making it relevant to portable products that must identify charging conditions. It can combine that function with UART, I2C, SPI, GPIO, and CapSense instead of requiring a separate charger-interface component. This consolidation is useful in compact docks, portable instruments, and accessory controllers. The exact USB data-line behavior and board-level charging design should be confirmed against the manufacturer datasheet and the host or power-source implementation.

Resumen de productos recomendados

CY7C65211-24LTXI Infineon Se usa en: USB-to-Serial Test Equipment, Industrial Sensor Gateway, Medical Device Connectivity, SPI Peripheral Programmer, USB-Enabled Control Panel, USB Battery-Charging Detection CY7C65211A-24LTXIT Same-family revision with UART, I2C, and SPI support Se usa en: USB-to-Serial Test Equipment, Industrial Sensor Gateway, Medical Device Connectivity, SPI Peripheral Programmer, USB-Enabled Control Panel, USB Battery-Charging Detection
What is the CY7C65211-24LTXIT?
The CY7C65211-24LTXIT is an Infineon EZ-USB full-speed USB 2.0 serial bridge controller with UART, I2C, and SPI support. According to the Infineon manufacturer datasheet, it supports UART operation up to 3 Mbps and I2C operation up to 400 kHz. The device also integrates CapSense, GPIO, and USB battery-charging detection compliant with revision 1.2 of the USB Battery Charging Specification.
What are the key specifications of CY7C65211-24LTXIT that engineers should know?
The principal specifications of the CY7C65211-24LTXIT are full-speed USB 2.0 connectivity, one configurable serial channel, UART support up to 3 Mbps, I2C support up to 400 kHz, SPI support, integrated CapSense, and USB battery-charging detection. The Infineon manufacturer datasheet identifies a 24-QFN package measuring 4 x 4 mm. Exact supply-voltage and absolute-pin limits should be taken directly from that datasheet before schematic release.
Where can I download the CY7C65211-24LTXIT datasheet PDF?
The official CY7C65211-24LTXIT datasheet PDF is available from Infineon through the manufacturer document link published for the CY7C65211 and CY7C65211A family. The document describes the USB controller, UART, I2C, SPI, CapSense, and battery-charging functions. It also provides the authoritative package drawing and pin descriptions needed for PCB implementation, rather than relying on a distributor diagram.
Where can I find the CY7C65211-24LTXIT pinout?
The CY7C65211-24LTXIT pinout is presented in the manufacturer datasheet and the package drawing for its 24-QFN 4 x 4 mm package. Use the numbered pin-description table when assigning USB, serial, GPIO, power, ground, and exposed-pad connections. The general product page also offers pinout resources, but the manufacturer datasheet should remain the controlling document when signal multiplexing or board-level constraints are in question.
Can the CY7C65211-24LTXIT bridge UART, I2C, and SPI peripherals?
Yes, the CY7C65211-24LTXIT can bridge UART, I2C, and SPI peripherals through a single full-speed USB connection. According to the Infineon manufacturer datasheet, the serial side supports UART rates up to 3 Mbps and I2C rates up to 400 kHz. Interface selection and multiplexing must be configured in device firmware, so the intended peripheral protocol should be verified before finalizing the PCB and host software.
What is CY7C65211-24LTXIT used for?
The CY7C65211-24LTXIT is used to connect serial peripherals to a USB host and can serve industrial control, medical equipment, sensor interfaces, programming equipment, and compact USB-enabled instruments. Its three-in-one UART, I2C, and SPI interface saves board space compared with separate bridge controllers, while CapSense adds touch sensing and battery-charging detection adds portable-device awareness.
CY7C65211-24LTXIT vs CY7C65211A-24LTXIT - which is better?
The CY7C65211A-24LTXIT is a device-family revision that retains the same USB-to-UART, USB-to-I2C, and USB-to-SPI positioning and the same 24-QFN 4 x 4 mm package designation. The documented family-level headline ratings of 3 Mbps UART and 400 kHz I2C show no difference between the two names. Selection should therefore follow lifecycle notices, firmware compatibility, and any revision-specific changes identified in the manufacturer datasheet.
What is the difference between CY7C65211-24LTXIT and CY7C65211A-24LTXIT?
The primary visible difference is the A revision designation in CY7C65211A-24LTXIT; both parts are listed as 24-QFN 4 x 4 mm EZ-USB serial bridge controllers with UART, I2C, SPI, CapSense, GPIO, and USB battery-charging functions. The available family description does not state a numerical electrical difference. Review the revision history and ordering information in the manufacturer datasheet to confirm any firmware or qualification implications.
When should I choose CY7C65211-24LTXIT over a separate USB bridge?
Choose the CY7C65211-24LTXIT when a compact product must connect more than one supported serial protocol through USB. A single 24-QFN device can cover UART up to 3 Mbps, I2C up to 400 kHz, and SPI while also providing GPIO and CapSense. Separate bridges may be preferable when their protocols can be optimized independently, but they increase component count, board area, and potentially firmware-management complexity.
Is CY7C65211-24LTXIT suitable for industrial and medical equipment?
The CY7C65211-24LTXIT is suitable for industrial and medical designs when its complete electrical, environmental, and qualification requirements satisfy the end product. The ordering code identifies an industrial temperature grade, and the device combines USB connectivity with UART, I2C, SPI, GPIO, and CapSense. Medical designs still require application-specific risk analysis and validation of every relevant device parameter.
What can replace CY7C65211-24LTXIT?
The CY7C65211A-24LTXIT is the closest identified device-family option because it uses the same 24-QFN 4 x 4 mm package designation and retains the same UART, I2C, SPI, CapSense, and USB battery-charging feature set. The documented family ratings show a 0 Mbps UART-rate difference and a 0 kHz I2C-rate difference. Confirm firmware, lifecycle, and revision-specific behavior before treating it as a production replacement.
What is the best Infineon equivalent for CY7C65211-24LTXIT?
The best identified Infineon-family equivalent is the CY7C65211A-24LTXIT, which retains the same 24-QFN 4 x 4 mm package and the same principal interfaces. It supports USB-to-UART, USB-to-I2C, and USB-to-SPI conversion, with family headline rates of 3 Mbps for UART and 400 kHz for I2C. Review the datasheet revision history and firmware requirements before substitution.
Where can I buy CY7C65211-24LTXIT online?
The CY7C65211-24LTXIT can be requested through the Request a Quote form on this product page, where the exact suffix, quantity, delivery target, and packaging requirements can be specified. The form is the appropriate route for current commercial availability because stock and lead time can change independently of device specifications. Do not infer production availability from a historical product-page listing.
What is the price of CY7C65211-24LTXIT?
Current pricing for the CY7C65211-24LTXIT should be obtained through the Request a Quote form on this page using the exact 24LTXIT suffix. The form captures required quantity, shipment destination, and delivery schedule so the commercial response can reflect the requested configuration. Static price information is omitted because it can change and may not represent the selected purchasing terms.
What is the lead time and stock status for CY7C65211-24LTXIT?
The current lead time and stock status for CY7C65211-24LTXIT should be confirmed through the Request a Quote form on this page. Enter the required quantity and target delivery date to receive a time-specific commercial response. Historical in-stock wording on a listing does not establish current inventory because allocation and component availability can change rapidly.

Datos de referencia de ingeniería para CY7C65211-24LTXIT — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the CY7C65211-24LTXIT when a compact design needs one full-speed USB connection to a configurable UART, I2C, or SPI peripheral and can also benefit from CapSense, GPIO, or USB battery-charging detection. Its 3 Mbps UART and 400 kHz I2C rates cover common control, programming, and sensor-interface requirements without requiring separate bridge controllers. The CY7C65211A-24LTXIT is the closest identified alternative because it retains the same 24-QFN package and documented family-level interfaces and rates. Select that revision after checking lifecycle, firmware, and revision-specific electrical requirements. Do not treat other ordering suffixes or packing variants as drop-in alternatives without comparing the package drawing, temperature grade, pin multiplexing, and firmware behavior. For systems requiring simultaneous independent UART, I2C, and SPI channels, the single-channel architecture may justify a multi-interface USB controller instead.

Comparación con alternativas

Parámetro Este producto CY7C65211A-24LTXIT
Brand Infineon Technologies Infineon Technologies
Package 24-QFN (4 x 4 mm) 24-QFN (4 x 4 mm)
USB Version USB 2.0 full-speed USB 2.0 full-speed
Maximum UART Rate 3 Mbps 3 Mbps
Maximum I2C Rate 400 kHz 400 kHz
Serial Interfaces UART, I2C, and SPI UART, I2C, and SPI
CapSense Integrated Integrated
USB Battery Charging Detection USB Battery Charging Specification revision 1.2 USB Battery Charging Specification revision 1.2
GPIO Supported Supported

Diferenciadores clave

  • Combines three serial protocols in one USB bridge (frente a CY7C65211A-24LTXIT)
  • Adds capacitive sensing to a multi-protocol bridge (frente a CY7C65211A-24LTXIT)
  • Maintains the same compact package and charging function (frente a CY7C65211A-24LTXIT)

Notas de diseño

Route the USB differential pair as a controlled-impedance pair with continuous reference-plane support and minimal stubs. Keep the USB connector, protection components, and controller in the same high-speed signal path, and place any required series or termination components according to the manufacturer reference layout. Avoid routing the differential pair across split power planes or between unrelated high-current paths because those transitions can degrade USB enumeration reliability.

Place all required bypass capacitors close to their associated power and ground pins, with short ground returns to the appropriate plane. The 24-QFN 4 x 4 mm package leaves little room for long escape paths, so complete pin assignment from the manufacturer pin-description table before placement. Confirm exposed-pad requirements, solder-mask clearance, and the recommended footprint against the current package drawing before releasing artwork.

Do not assume that every member of the CY7C65211 ordering family is a drop-in replacement. The 24LTXI and 24LTXIT names can differ in ordering or delivery characteristics, while the A suffix identifies a device-family revision. For a production substitution, compare the exact package drawing, temperature grade, firmware behavior, USB descriptors, pin multiplexing, battery-charging behavior, and lifecycle status rather than relying only on the shared interface description.

Choose peripheral-side voltage levels and interface timing from the manufacturer electrical tables rather than from the USB rating. UART, I2C, and SPI can have different allowable input voltages, rise times, and output characteristics. Confirm pull-up requirements for I2C, SPI mode behavior, idle levels, and the GPIO state during reset so that attached peripherals remain in a safe state while the USB host enumerates the bridge.

Información de cumplimiento

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

RoHS compliance and MSL 3 are identified for this device. The ordering code denotes an industrial temperature grade, but no AEC-Q100 qualification is identified.

Datos verificados el: 2026-11-10 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

cy7c65211 datasheet cypress cy7c65211 CY7C65211-24LTXIT datasheet CY7C65211-24LTXIT pinout CY7C65211-24LTXIT USB UART CY7C65211-24LTXIT I2C SPI CY7C65211-24LTXIT 3 Mbps CY7C65211-24LTXIT 400 kHz CY7C65211-24LTXIT replacement CY7C65211-24LTXIT vs CY7C65211A-24LTXIT CY7C65211-24LTXIT equivalent CY7C65211-24LTXIT 24-QFN footprint CY7C65211-24LTXIT application circuit CY7C65211-24LTXIT price

Componentes & términos relacionados

Infineon Technologies Cypress Semiconductor CY7C65211-24LTXIT CY7C65211-24LTXI CY7C65211A-24LTXIT EZ-USB USB serial bridge USB interface controller full-speed USB controller USB 2.0 UART I2C SPI CapSense GPIO USB Battery Charging Specification revision 1.2 3 Mbps UART 400 kHz I2C 24-QFN QFN family surface mount industrial temperature grade RoHS MSL 3
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ