CY7C65211-24LTXIT - USB Serial Bridge | Infineon
MPN: CY7C65211-24LTXIT ✓ AktifCY7C65211-24LTXIT Genel Bakış
A USB-serial bridge is a USB interface controller that allows a legacy serial peripheral to communicate with a host computer over USB. The CY7C65211 belongs to the EZ-USB family of USB interface controllers and sits between a USB connector and an embedded UART, I2C, or SPI peripheral. This bridge role places the controller within the broader interface-controller and power-management ecosystem for compact industrial, medical, and consumer equipment.
The controller combines three selectable serial interfaces in one device, reducing the need for separate USB-to-UART, USB-to-I2C, and USB-to-SPI bridge components. Its 3 Mbps UART capability supports faster data links than many conventional USB-UART converters, while 400 kHz I2C operation addresses standard-mode peripheral buses. CapSense extends the device beyond basic serial conversion, and USB 2.0 battery-charging detection supports portable designs that require downstream-device charging awareness.
The CY7C65211 family uses an internal microcontroller-based architecture with configurable USB and serial interfaces. Because the USB side operates at full speed, the device is intended for control and data-transfer applications rather than high-bandwidth storage. GPIO and CapSense functions provide additional control or touch-input capability without requiring separate devices. Exact operating voltage, clock architecture, memory configuration, and pin-level electrical limits must be confirmed in the manufacturer datasheet before a new design is released.
Typical uses include configuring legacy serial equipment through USB, connecting sensor boards that communicate over I2C, programming SPI peripherals, and adding touch sensing to USB-controlled panels. The same mixed-interface capability is useful in compact instruments where board area is limited and a single controller must service more than one peripheral type. Firmware and host-side driver support should be evaluated early because interface configuration and enumeration behavior depend on the selected application architecture.
Layout planning should reserve a solid USB connection, regulated supply, ground reference, decoupling network, and accessible test points. Keep the USB differential pair impedance-controlled and minimize stub branches, especially when the bridge is placed behind cables or connectors. Firmware configuration, peripheral-side I/O levels, and pin multiplexing must be reconciled with the board netlist because incorrect mode selection can route signals to unintended pins.
This product overview combines the manufacturer interface capabilities, package information, ordering variants, and cross-reference findings with practical guidance for USB-to-serial integration. It also distinguishes verified pin-compatible device-family options from package variants that should not be treated as drop-in replacements without a full footprint and temperature-grade review.
Drop-in alternatifler için CY7C65211-24LTXIT — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller CY7C65211-24LTXIT (aynı form faktörü ve ayağa oturma) — farklı olan Package, Supported Serial Interfaces.
CY7C65211A-24LTXIT
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
CY7C65211-24LTXIT Özellikler
| Device Type | Full-speed USB serial bridge controller |
| USB Specification | USB 2.0 full-speed |
| Supported Serial Interfaces | UART, I2C, and SPI |
| Maximum UART Data Rate | 3 Mbps |
| Maximum I2C Data Rate | 400 kHz |
| Number of Serial Channels | 1 channel |
| Integrated Peripheral | CapSense touch-sensing controller |
| Battery Charging Detection | USB Battery Charging Specification revision 1.2 |
| GPIO Support | General-purpose GPIO |
| Paket | 24-QFN, 4 x 4 mm |
| Montaj Türü | Surface mount |
| Operating Temperature Grade | Industrial grade |
| RoHS Durumu | Compliant |
| Moisture Sensitivity Level | MSL 3 |
CY7C65211-24LTXIT 24-qfn, 4 x 4 mm Pin Yapısı Kılavuzu
CY7C65211-24LTXIT (24-qfn, 4 x 4 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: CY7C65211-24LTXIT.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
CY7C65211-24LTXIT için uygundur 6 uygulamas: USB-to-Serial Test Equipment, Industrial Sensor Gateway, Medical Device Connectivity, SPI Peripheral Programmer, USB-Enabled Control Panel, USB Battery-Charging Detection.
USB-to-Serial Test Equipment
The CY7C65211-24LTXIT fits test fixtures that need one USB port to communicate with legacy UART, I2C, or SPI instrumentation. Its UART rate of up to 3 Mbps supports faster command and data transfers than many low-speed serial bridges, while I2C operation up to 400 kHz accommodates common sensor and EEPROM buses. The 24-QFN 4 x 4 mm footprint helps keep interface density high in compact fixtures. Firmware must select the correct serial mode and implement the expected command protocol before production testing begins.
Önerilen
Industrial Sensor Gateway
For industrial sensor gateways, the CY7C65211-24LTXIT can connect a USB host to sensors or controllers using UART, I2C, or SPI. The single-channel architecture is useful when a gateway needs a configurable peripheral interface rather than three simultaneous protocol converters. Its 400 kHz I2C capability supports standard-mode devices, while 3 Mbps UART enables higher-rate legacy links. GPIO provides additional control signaling, and the compact 24-QFN package preserves board area for sensing and isolation components.
Önerilen
Medical Device Connectivity
The CY7C65211-24LTXIT can serve as the USB interface in medical equipment that communicates with a serial accessory, sensor module, or service port. UART, I2C, and SPI support permits reuse across multiple product variants, while GPIO can handle auxiliary device-control signals. CapSense can add touch controls without a separate sensing controller. The industrial-grade ordering option supports industrial temperature environments, but medical suitability still depends on system-level electrical validation, risk assessment, and the applicable product requirements.
Önerilen
SPI Peripheral Programmer
The CY7C65211-24LTXIT is appropriate for a compact SPI programmer that connects a legacy programming fixture to a USB host. Its single serial channel can be configured for SPI, allowing firmware to handle programming clocks, commands, and status signaling. USB full-speed operation fits the low-to-moderate bandwidth of many device-programming workflows, while GPIO can assist fixture control. The 4 x 4 mm 24-QFN package is especially useful where the connector, level conversion, and target-device circuitry compete for limited board area.
Önerilen
USB-Enabled Control Panel
The CY7C65211-24LTXIT can bridge a USB host to a control panel containing UART, I2C, or SPI peripherals. CapSense adds touch-detection capability for keys, sliders, or proximity controls, while GPIO supports indicators, interlocks, or discrete inputs. Using one controller for data and touch functions can reduce component count in a space-constrained panel. The mixed-protocol capability is valuable during product development because different panel variants can use the same controller family, although firmware configuration must ensure that each peripheral is assigned to the correct interface.
Önerilen
USB Battery-Charging Detection
The CY7C65211-24LTXIT integrates battery-charging detection compliant with revision 1.2 of the USB Battery Charging Specification, making it relevant to portable products that must identify charging conditions. It can combine that function with UART, I2C, SPI, GPIO, and CapSense instead of requiring a separate charger-interface component. This consolidation is useful in compact docks, portable instruments, and accessory controllers. The exact USB data-line behavior and board-level charging design should be confirmed against the manufacturer datasheet and the host or power-source implementation.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: CY7C65211-24LTXIT — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | CY7C65211A-24LTXIT |
|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies |
| Package | 24-QFN (4 x 4 mm) | 24-QFN (4 x 4 mm) |
| USB Version | USB 2.0 full-speed | USB 2.0 full-speed |
| Maximum UART Rate | 3 Mbps | 3 Mbps |
| Maximum I2C Rate | 400 kHz | 400 kHz |
| Serial Interfaces | UART, I2C, and SPI | UART, I2C, and SPI |
| CapSense | Integrated | Integrated |
| USB Battery Charging Detection | USB Battery Charging Specification revision 1.2 | USB Battery Charging Specification revision 1.2 |
| GPIO | Supported | Supported |
Ana Farklılayıcılar
- Combines three serial protocols in one USB bridge (karşılaştırma:CY7C65211A-24LTXIT)
- Adds capacitive sensing to a multi-protocol bridge (karşılaştırma:CY7C65211A-24LTXIT)
- Maintains the same compact package and charging function (karşılaştırma:CY7C65211A-24LTXIT)
Tasarım Notları
Route the USB differential pair as a controlled-impedance pair with continuous reference-plane support and minimal stubs. Keep the USB connector, protection components, and controller in the same high-speed signal path, and place any required series or termination components according to the manufacturer reference layout. Avoid routing the differential pair across split power planes or between unrelated high-current paths because those transitions can degrade USB enumeration reliability.
Place all required bypass capacitors close to their associated power and ground pins, with short ground returns to the appropriate plane. The 24-QFN 4 x 4 mm package leaves little room for long escape paths, so complete pin assignment from the manufacturer pin-description table before placement. Confirm exposed-pad requirements, solder-mask clearance, and the recommended footprint against the current package drawing before releasing artwork.
Do not assume that every member of the CY7C65211 ordering family is a drop-in replacement. The 24LTXI and 24LTXIT names can differ in ordering or delivery characteristics, while the A suffix identifies a device-family revision. For a production substitution, compare the exact package drawing, temperature grade, firmware behavior, USB descriptors, pin multiplexing, battery-charging behavior, and lifecycle status rather than relying only on the shared interface description.
Choose peripheral-side voltage levels and interface timing from the manufacturer electrical tables rather than from the USB rating. UART, I2C, and SPI can have different allowable input voltages, rise times, and output characteristics. Confirm pull-up requirements for I2C, SPI mode behavior, idle levels, and the GPIO state during reset so that attached peripherals remain in a safe state while the USB host enumerates the bridge.
Uyumluluk Bilgisi
RoHS compliance and MSL 3 are identified for this device. The ordering code denotes an industrial temperature grade, but no AEC-Q100 qualification is identified.