DG409AK - Dual 4:1 CMOS Analog Multiplexer | Analog Devices
N.º de pieza: DG409AK ✗ Fin de vidaDG409AK Descripción general
An analog multiplexer is an interface IC that connects one of several analog inputs to a shared output while minimizing signal-path distortion. In the broader semiconductor hierarchy, the DG409AK belongs to the analog switch and multiplexer class, the interface IC family, and ultimately the broader semiconductor category. Its two 4:1 sections allow two signals to be routed independently, reducing the number of external switches required in measurement and control equipment.
The DG409AK supports single-supply operation from 5 V to 30 V and dual-supply operation from ±5 V to ±20 V. Low on-state resistance limits insertion loss, while the specified 1.5-ohm channel-to-channel matching helps preserve amplitude consistency between selected channels. Maximum turn-on and turn-off times of 150 ns support rapid control sequencing, although propagation delay, charge injection, and off-state isolation must also be considered in precision applications.
Internally, the device uses CMOS analog-switching structures controlled by TTL- or CMOS-compatible digital inputs. Independent select and enable controls allow each multiplexer section to route signals when required. The Analog Devices DG409 family documentation emphasizes guaranteed channel matching, on-resistance flatness over the specified signal range, low charge injection, low input leakage, low power consumption, rail-to-rail signal handling, and ESD protection greater than 2000 V.
Typical applications include multimeter and bench-instrument signal selection, automated test equipment, industrial data acquisition, sensor-interface routing, and control systems that must select several analog inputs without adding a separate analog switch for every channel. The 16-pin CERDIP package also suits legacy equipment where through-hole construction and a stable industrial footprint are important.
Designers should verify supply voltage, input-signal range, logic thresholds, leakage, charge injection, and switch timing against the exact operating conditions. A low-impedance source, adequate input protection, and clean grounding help preserve measurement accuracy. Because the DG409AK is listed as obsolete, new production designs should evaluate current DG409-family options and confirm availability, lifecycle, and pin compatibility before committing a layout.
This page combines the DG409AK functional description, verified electrical characteristics, practical application guidance, package considerations, and a conservative drop-in comparison. It is intended to help engineers distinguish true legacy replacements from parts that only share the DG409 name or general multiplexing function.
Alternativas directas para DG409AK — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
DG409AK/883B
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
DG409AK/883
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
DG409AK Especificaciones
| Multiplexer Configuration | Dual 4:1 |
| Number of Circuits | 2 circuits |
| On-State Resistance | 100 ohms maximum |
| Channel-to-Channel Matching | 1.5 ohms maximum |
| Turn-On Time | 150 ns maximum |
| Turn-Off Time | 150 ns maximum |
| Single-Supply Voltage Range | 5 V to 30 V |
| Dual-Supply Voltage Range | -20 V to +20 V |
| Número de pines | 16 pins |
| Encapsulado | 16-pin CERDIP |
| Tipo de montaje | Through-hole |
| Technology | CMOS |
| Logic Compatibility | TTL/CMOS-compatible |
| ESD Protection | Greater than 2000 V |
| Input Leakage | 100 nA maximum |
| Charge Injection | 15 pC maximum |
| Power Consumption | 1.25 mW maximum |
Guía de configuración de pines de DG409AK 16-pin cerdip
Configuración de pines para DG409AK (encapsulado 16-pin cerdip). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para DG409AK.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
DG409AK es adecuado para 6 aplicacións: Automated Test Equipment, Precision Data Acquisition, Bench Instrument Signal Routing, Industrial Sensor Interface, Control-System Signal Multiplexing, Legacy Equipment Maintenance.
Automated Test Equipment
The DG409AK fits automated test equipment that must connect several analog sources or returns to shared measurement channels. Two independent 4:1 sections allow two routing paths to be controlled separately, reducing the number of discrete relays required around the test fixture. The 150 ns maximum turn-on and turn-off times support rapid sequencing, while the 1.5-ohm channel-to-channel matching helps limit measurement-gain differences between test points. Designers should account for the 100-ohm maximum on resistance, source impedance, leakage, and connector losses when setting error budgets for low-amplitude or high-impedance measurements.
Recomendado
Precision Data Acquisition
The DG409AK is useful in multichannel data-acquisition systems where transducers or conditioned sensor outputs must share an analog-to-converter input. Its dual 4:1 architecture provides two selectable input banks, while 1.5-ohm channel matching reduces systematic amplitude variation between routes. The maximum 150-ns switching time allows the multiplexer to change channels quickly after a settling interval. For bridge sensors, low-current measurements, or high-impedance sources, evaluate input leakage, charge injection, source impedance, and the 100-ohm on resistance before deciding whether the measurement resolution is sufficient.
Recomendado
Bench Instrument Signal Routing
The DG409AK supports signal routing in bench instruments that must select among external inputs, internal references, or calibration networks. Two separately enabled 4:1 sections can manage a measurement input and a control or reference path within the same instrument architecture. The 100-ohm maximum on resistance is manageable for many medium-impedance circuits, while the specified matching and switching speed improve repeatability during source selection. Front-end design should include input attenuation or buffering when driving low impedances, and it should protect external inputs against excessive voltage and ESD events.
Recomendado
Industrial Sensor Interface
The DG409AK can select multiple conditioned industrial sensor outputs before conversion or further processing. The two 4:1 sections allow related sensor groups to share downstream circuitry, reducing connector count and simplifying control. Matching of 1.5 ohms between channels supports consistent routing when source impedances are controlled, and the 150-ns maximum switching times suit systems that alternate channels on a deterministic schedule. Long cable-connected sensors should be isolated from ground loops, and the system must remain within the device's absolute-maximum ratings even during disconnected or abnormal sensor conditions.
Recomendado
Control-System Signal Multiplexing
The DG409AK can route command, feedback, or setpoint signals in an analog control subsystem where several sources must reach a common actuator or controller interface. Independent enable inputs permit unused routing sections to remain inactive, and TTL- or CMOS-compatible control logic simplifies integration with older digital controllers. The specified 150-ns maximum switching times are much shorter than typical control-loop intervals, but mechanical stability, glitch behavior, and charge injection still determine whether a transition is acceptable. For safety-critical systems, add diagnostics and use qualified components specified by the applicable system requirements.
Recomendado
Legacy Equipment Maintenance
The DG409AK is well suited to repairing or extending legacy electronic instruments that use a 16-pin through-hole multiplexer and cannot accept a surface-mount redesign. Its established DG409 function, 100-ohm maximum on resistance, and dual 4:1 organization make it practical for maintaining existing routing architecture. Because the device is obsolete, engineers should preserve the original land pattern, verify every supply and logic connection, and confirm the required temperature and screening conditions. The obsolete status makes careful sourcing, date-code review, and documented inspection especially important for long-lived industrial equipment.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para DG409AK — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | DG409AK/883B | DG409AK/883 |
|---|---|---|---|
| Package | 16-pin CERDIP | 16-pin CDIP | 16-pin CDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | Dual 4:1 | Dual 4:1 | Dual 4:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Maximum On-State Resistance | 100 ohms maximum | 100 ohms maximum | 100 ohms maximum |
| Channel-to-Channel Matching | 1.5 ohms maximum | 1.5 ohms maximum | 1.5 ohms maximum |
| Maximum Turn-On Time | 150 ns maximum | 150 ns maximum | 150 ns maximum |
| Maximum Turn-Off Time | 150 ns maximum | 150 ns maximum | 150 ns maximum |
| Supply Voltage Range | 5 V to 30 V single; ±5 V to ±20 V dual | 5 V to 30 V single; ±5 V to ±20 V dual | 5 V to 30 V single; ±5 V to ±20 V dual |
| Charge Injection | 15 pC maximum | 15 pC maximum | 15 pC maximum |
| Input Leakage | 100 nA maximum | 100 nA maximum | 100 nA maximum |
| Processing Designation | Standard DG409AK | 883B designation | 883 designation |
Diferenciadores clave
- Dual independent analog routing sections (frente a DG409AK/883B)
- Direct 16-pin through-hole family substitution (frente a DG409AK/883)
- Legacy ceramic-package construction (frente a DG409AK/883B)
Notas de diseño
Treat the 100-ohm maximum on resistance as part of the complete signal-path impedance. In a series path with source resistance Rs and load resistance RL, the switch contributes up to 100 ohms, creating a divider that can attenuate the selected signal. Use a low source impedance and high input impedance when preserving amplitude matters. Also evaluate capacitance and propagation delay at the operating frequency, because the 150-ns switching-time rating alone does not describe the complete analog bandwidth.
Use the manufacturer pin-configuration table to assign the 16-pin through-hole footprint and confirm whether the board requires a ceramic or plastic DIP outline. Keep the two multiplex sections' supply and ground pins connected according to the DG409 family guidance. Route the selected analog signals away from digital control traces where possible, provide a solid ground reference, and avoid long stubs between the package and front-end components because they can increase coupling and settling time.
Do not select the DG409AK solely from the 4:1 multiplexing label. Verify the exact ordering code, package outline, pin assignments, supply arrangement, absolute-maximum input voltage, temperature grade, and processing requirements before substitution. The DG409AK/883 and DG409AK/883B options may differ in screening and sourcing conditions even though they retain the same core DG409AK function and 16-pin through-hole package format.
Información de cumplimiento
The DG409 family documentation identifies ESD protection greater than 2000 V, but it does not establish RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the DG409AK ordering code. The 883 designation should not be treated as an automotive qualification without a specific qualification record.