DP83865DVH - 1G Ethernet PHY, 128-PQFP | Texas Instruments
N.º de pieza: DP83865DVH ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
DP83865DVH Descripción general
An Ethernet PHY is the physical-layer component that converts digital Ethernet data supplied by a MAC into electrical signaling for a copper network, and receives analog signals from the cable. Within the Ethernet hierarchy, the PHY connects the digital MAC interface and the 10/100/1000BASE-T medium. This distinction matters because protocol handling remains above the PHY while the DP83865DVH performs line signaling, clock and data recovery, and physical-layer encoding functions.
Verified source data identifies a 1 Gbit/s data rate, eight transceiver channels, a 1.71 V to 1.89 V supply range, approximately 430 mA supply current, and a 128-pin PQFP package. The device integrates physical medium-dependent sublayers required for 10BASE-T, 100BASE-TX, and 1000BASE-T Ethernet. Exact media-interface modes, clock tolerances, transceiver electrical limits, and pin-level functions are not present in the supplied search extracts and therefore require confirmation from the manufacturer datasheet before layout release.
Typical implementation is a copper Gigabit Ethernet port in industrial controllers, embedded computers, test equipment, network interface cards, and communications hardware. The 128-PQFP footprint favors multilayer PCB routing and external magnetics rather than compact modules, while the 1.89 V maximum stated core supply requires a regulator with suitable headroom and power integrity. A network magnetics or integrated coupling arrangement is also required at the cable side, subject to the complete reference design.
Engineers should preserve the exact interface voltage, termination, crystal or clock source, reset, and power-tree requirements given in the full DP83865 datasheet. Because no verified pricing schedule was supplied, unit prices remain marked as data needed rather than being inferred from generic distributor listings. The search data also indicates that no pin-to-pin DP83865 replacement is offered by TI, so substitution requires interface and PCB validation rather than an assumed footprint match.
This page consolidates the verified distributor specifications, procurement sources, replacement evidence, and engineering cautions. It distinguishes confirmed electrical facts from unavailable details and avoids treating functionally similar PHYs as verified drop-in devices. That distinction is critical because Ethernet PHYs may use the same 128-pin package while differing in interface modes, strap behavior, clocking, register maps, and analog performance.
Alternativas directas para DP83865DVH — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
No hay alternativas directas disponibles para este producto.
Solicitar alternativasDP83865DVH Especificaciones
| Product Type | Gigabit Ethernet physical-layer transceiver |
| Supported Ethernet Protocols | 10BASE-T, 100BASE-TX, 1000BASE-T |
| Maximum Data Rate | 1 Gbit/s |
| Number of Ports | 1 Ethernet port |
| Interface Configuration | 8/8 transceiver |
| Core Supply Voltage Range | 1.71 V to 1.89 V |
| Corriente de alimentación | 430 mA |
| Rango de temperatura de funcionamiento | 0 C to +70 C |
| Temperature Grade | Commercial |
| Package Type | 128-PQFP |
| Package Dimensions | 14 mm x 20 mm |
| Terminal Form | Gull wing |
| Recuento de pines | 128 pins |
| Tipo de montaje | Surface mount |
| Integrated PMD Sublayers | Yes |
| Copper Media Support | 10BASE-T, 100BASE-TX, and 1000BASE-T |
Guía de configuración de pines de DP83865DVH 14 mm x 20 mm
Configuración de pines para DP83865DVH (encapsulado 14 mm x 20 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para DP83865DVH.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
DP83865DVH es adecuado para 6 aplicacións: Industrial Embedded Controller Ethernet Port, Network Interface Card, Programmable Test and Measurement Equipment, Communications Gateway, Data Acquisition System, Power and Energy Monitoring Controller.
Industrial Embedded Controller Ethernet Port
DP83865DVH fits a commercial-temperature embedded controller that needs one copper Ethernet port with 10/100/1000BASE-T support. Its confirmed 1 Gbit/s maximum data rate and integrated PMD sublayers allow the controller MAC to communicate through the PHY without implementing baseband signaling separately. The device uses a 1.71 V to 1.89 V core supply and is specified from 0 C to +70 C, so the system must regulate the rail and maintain its commercial temperature envelope. Use the manufacturer layout for high-speed clocks, digital interfaces, supply returns, and magnetics. The 128-PQFP footprint requires 0.5 mm-pitch routing and multilayer PCB discipline, but it remains practical on a controlled industrial-control board.
Recomendado
Network Interface Card
DP83865DVH can supply the physical layer for a single-port gigabit network interface card driven by a local controller or ASIC. The PHY supports 10BASE-T, 100BASE-TX, and 1000BASE-T, allowing one copper interface to negotiate legacy or gigabit links where required. The verified 430 mA supply-current figure makes the 1.89 V core rail a substantial load, requiring a regulator with appropriate transient response and copper area. The 14 x 20 mm PQFP offers ample pins and routing access compared with a small QFN, although care is still needed around clocks, digital interfaces, and analog separation. Final card-level validation must include insertion, return loss, link training, thermal behavior, and EMC testing.
Recomendado
Programmable Test and Measurement Equipment
DP83865DVH is applicable to a 1 Gbit/s copper Ethernet connection on programmable instrumentation when the controller already matches its physical-layer and media requirements. A single PHY supporting 10BASE-T, 100BASE-TX, and 1000BASE-T permits service, control, and data traffic over one connector. The commercial 0 C to +70 C rating is appropriate for ordinary indoor bench equipment, while the 1.71 V to 1.89 V core supply requires a quiet regulator and close decoupling. Designers should isolate high-current switching nodes from PHY circuitry and validate magnetics according to the manufacturer reference design. If higher temperature or diagnostic performance is mandatory, compare a newer qualified PHY rather than assuming the existing 128-pin footprint is interchangeable.
Recomendado
Communications Gateway
DP83865DVH can provide the copper network endpoint for a communications gateway that bridges a local processor or FPGA to an external 10/100/1000BASE-T network. Its eight transceiver channels and integrated PMD support place physical signaling in one device, while the host remains responsible for MAC-facing control and network traffic. The large 128-PQFP package exposes more routing options for demanding clocks and interfaces than a compact QFN, but its lead pitch requires careful assembly and inspection. The reported 430 mA current also affects the system power budget, so designers should reserve regulator capacity and measure inrush during startup. Confirm supported clock and digital interfaces in the complete datasheet before connecting a particular FPGA or processor bank.
Recomendado
Data Acquisition System
DP83865DVH can serve as the 1 Gbit/s Ethernet physical layer in a data-acquisition system that transfers synchronized measurements from an FPGA or processing module to a host computer. The PHY handles copper Ethernet support at 10, 100, or 1000 Mbit/s, but sustained application throughput still depends on host-interface timing, packet size, DMA behavior, and processor capacity. The verified 1.71 V to 1.89 V supply requirement should be included in the analog and digital power-budget review, with special attention to the listed 430 mA current. Printed-circuit design should separate noisy processor supplies from PHY references and clocks and preserve the prescribed media-side geometry. Validate packet loss, sustained transfer, cable insertion, and recovery from link interruptions before deployment.
Recomendado
Power and Energy Monitoring Controller
DP83865DVH is suitable for a commercial power-monitoring controller that exposes measurements, configuration data, and alarms through a copper Ethernet port. Supporting 10BASE-T, 100BASE-TX, and 1000BASE-T allows compatibility with legacy management networks while permitting 1 Gbit/s communication on suitable infrastructure. Because the PHY is part of an embedded system rather than a power-conversion IC, SOA data are not applicable. Its verified 430 mA supply current must be added to the controller's power budget, and the 1.71 V to 1.89 V core range requires a regulator with appropriate headroom. Keep switching-node copper and high di/dt loops away from PHY and magnetics grounding, then test EMC emissions and network robustness with realistic cables and loads.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para DP83865DVH — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto |
|---|---|
| Brand | Texas Instruments |
| Package | 128-PQFP, 14 mm x 20 mm |
| Maximum Data Rate | 1 Gbit/s |
| Ethernet Support | 10BASE-T, 100BASE-TX, 1000BASE-T |
| Core Supply Voltage | 1.71 V to 1.89 V |
| Supply Current | 430 mA |
| Operating Temperature | 0 C to +70 C |
| Pin Count | 128 pins |
| Integrated PMD Sublayers | Yes |
| Temperature Grade | Commercial |
Diferenciadores clave
- Confirmed support for 10BASE-T, 100BASE-TX, and 1000BASE-T (frente a DP83867 application-directed alternate)
- Large 128-PQFP interface and routing package (frente a DP83869 application-directed alternate)
- Narrow verified core-supply rail (frente a DP83867IRPAPR distributor-listed replacement candidate)
Notas de diseño
Use the verified 1.71 V to 1.89 V core-supply range as the regulator-design boundary and include the listed 430 mA current in the power budget. Estimated core power at 1.89 V and 430 mA is 0.813 W, calculated from 1.89 V x 0.430 A; this is a planning estimate rather than a manufacturer maximum-power specification. Confirm startup current, voltage tolerance, sequencing, all I/O domains, and magnetics supplies from the complete datasheet before selecting regulators or magnetics.
Treat the 128-PQFP as a 0.5 mm-pitch assembly design and allocate its full 14 x 20 mm body plus leads and courtyard. Follow the manufacturer footprint rather than relying on a generic PQFP symbol. Verify pin numbering, pin-1 orientation, solder mask, paste volume, via placement, and assembly clearance. Because the public snippets do not provide the 128-pin map, every net must be checked against the official package drawing before release.
Preserve the complete reference layout for clock inputs, digital interfaces, supply decoupling, analog media signals, magnetics, and ground returns. Keep noisy switching and high di/dt copper away from PHY and transformer grounding, and avoid routing flexible or coax-like media signals through areas with uncontrolled discontinuities. The supplied data does not specify trace lengths, impedance targets, or isolation spacing, so obtain those values from the full manufacturer documentation and PCB guidelines rather than estimating them.
Do not assume DP83867 or DP83869 can be inserted without redesign. TI support explicitly states that no pin-to-pin replacement is offered for DP83865 and describes those devices only as application-dependent alternates. A shared 128-PQFP family, functional gigabit support, or a distributor's functional-replacement description is insufficient proof of compatibility. Check host-interface modes, I/O voltage, clocks, straps, MDIO behavior, software, magnetics, and every package pin before substitution.
Información de cumplimiento
The supplied verified snippets do not state formal RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. No compliance claim is inferred from the manufacturer identity or commercial-temperature grade.
