Texas Instruments

DS90C401MX/NOPB - Dual LVDS Driver, 155.5 Mbps | Texas Instruments

N.º de pieza: DS90C401MX/NOPB ✓ Activo
4.5 V to 5.5 V Vdss 8-pin SOIC (D) Package
MOQ: 1 |

DS90C401MX/NOPB Descripción general

The Texas Instruments DS90C401MX/NOPB is a dual Low Voltage Differential Signaling (LVDS) driver optimized for high-data-rate, low-power point-to-point interfaces. The device provides two drivers, operates from a 4.5 V to 5.5 V supply, and supports data rates up to 155.5 Mbps. It is packaged in an 8-pin SOIC package identified as SOIC (D). The DS90C401 is designed to work with the DS90C402 receiver as a complete dual high-speed point-to-point interface solution.

An LVDS driver is a differential signal-line transmitter that uses a balanced current-mode output stage. By steering current between two complementary outputs, the DS90C401 can transmit high-speed digital information while reducing common-mode noise and improving noise immunity over longer point-to-point interconnects. LVDS is part of the broader interface-IC hierarchy, which includes low-voltage differential signaling, differential line drivers, and high-speed serial interface devices.

The current-mode architecture keeps power dissipation relatively low at high operating frequencies and limits the short-circuit fault current. These characteristics make the DS90C401MX/NOPB useful where data must be transferred reliably between circuit boards, rack-mounted equipment, test systems, or other short-reach high-speed links. The dual-driver configuration allows two LVDS channels to be implemented in one package, reducing component count when multiple links are required.

The principal application is a dual point-to-point interface pairing the DS90C401 with one or more DS90C402 receivers. Each driver channel provides complementary differential outputs intended for a properly terminated LVDS transmission line. Designers should use controlled-impedance routing, maintain a continuous ground reference, place termination close to the receiver, and follow the manufacturer’s recommended decoupling and pinout guidance.

The DS90C401MX/NOPB also offers a practical alternative to single-channel driver arrangements when two related high-speed links are needed. Its 4.5 V to 5.5 V operating range supports conventional 5 V interface systems, while the 155.5 Mbps data-rate capability addresses legacy and industrial data links. The /NOPB suffix identifies the lead-free, non-PB-free-package configuration as designated by Texas Instruments.

This page combines the device’s core electrical and packaging characteristics with application guidance, comparison notes, and design considerations. It also identifies the exact DS90C401MX/NOPB manufacturer datasheet and product-page resources for authoritative electrical characteristics, recommended operating conditions, pin assignments, and application schematics.

Alternativas directas para DS90C401MX/NOPB — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con DS90C401MX/NOPB (mismo factor de forma y huella) — difiere en Package, Product Type, Driver Architecture.

Texas Instruments
Package: 8-lead small-outline package
Product Type: Dual low voltage differential signaling (LVDS) driver
Texas Instruments
Package: 8-SOIC, 8 pins
Product Type: Dual LVDS driver, 2/0 configuration
Driver Architecture: Current-mode differential driver
Texas Instruments
Package: 8-pin SOIC
Product Type: Dual LVDS driver
Driver Architecture: Current-mode driver

DS90C401MX

✅ Sustitución directa
Texas Instruments
📦 8-pin SOIC (D)
Dual LVDS driver · Low Voltage Differential Signaling (LVDS) · 2 driver channels · 8-pin SOIC · Surface mount · Transmitter/driver · Point-to-point differential signaling · Current-mode driver

Consulte el precio

Ver hoja de datos →

DS90C401M/NOPB

✅ Sustitución directa
📦 8-pin SOIC (D)
Same dual LVDS driver function and 8-pin SOIC package family; ordering code differs while identified core ratings remain 0 percentage points apart

📋 Alternativa de referencia (no en el catálogo)

DS90C401MX/NOPB Especificaciones

Device Type Dual LVDS driver
Number of Drivers 2 drivers
Number of Receivers 0 receivers
Supply Voltage Range 4.5 V to 5.5 V
Maximum Data Rate 155.5 Mbps
Protocol LVDS
Output Architecture Balanced current-mode differential driver
Encapsulado 8-pin SOIC (D)
Package Width 3.90 mm
Tipo de montaje Surface mount
Packaging Tape and reel (TR) or cut tape (CT)
Rango de temperatura de funcionamiento -40°C to +85°C
Lead-Free Status Lead-free / NOPB configuration

Guía de configuración de pines de DS90C401MX/NOPB 3.90 mm

Configuración de pines para DS90C401MX/NOPB (encapsulado 3.90 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 3.90 mm para DS90C401MX/NOPB

No hay datos detallados de patillaje disponibles para DS90C401MX/NOPB.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

DS90C401MX/NOPB es adecuado para 6 aplicacións: DS90C402 Point-to-Point Links, Industrial Data Acquisition, Test and Measurement Systems, Backplane Data Transmission, Video and Imaging Data Links, Server and Network Interface Cards.

🌐

DS90C402 Point-to-Point Links

The DS90C401MX/NOPB is designed to pair with the Texas Instruments DS90C402 as a two-channel high-speed point-to-point interface. Its two balanced current-mode LVDS drivers operate from 4.5 V to 5.5 V and support rates up to 155.5 Mbps, allowing one transmitter package to serve two related links. Each output pair should be routed with controlled impedance and terminated in accordance with the receiver circuit. This arrangement is useful when a system needs two data paths without using separate single-channel driver packages, while the current-mode architecture helps maintain low power dissipation at high frequency.

🏭

Industrial Data Acquisition

The dual LVDS channels of the DS90C401MX/NOPB suit industrial acquisition equipment that transfers clocked or sampled data between circuit boards. The 155.5 Mbps capability provides margin for moderate-rate parallel-to-serial conversion stages, while differential current-mode signaling improves noise immunity on inter-board links. Designers should maintain a continuous ground plane, use equal-length routing where timing margins require it, and place the receiver termination close to the receiving device. The 4.5 V to 5.5 V supply range also aligns with conventional 5 V industrial interface electronics.

🔧

Test and Measurement Systems

The DS90C401MX/NOPB can provide two low-power differential transmit paths in instrumentation and automated test equipment that connects control logic to remote acquisition or processing modules. Its two-driver configuration reduces the number of transmit packages required for a dual-channel system, and the balanced LVDS outputs help prevent common-mode pickup from disturbing sensitive measurements. Designers should characterize the complete channel with the intended receiver, connector, and cable, including propagation delay, jitter, impedance, and termination. Controlled impedance and a continuous ground return are essential for repeatable measurements.

🖥️

Backplane Data Transmission

The DS90C401MX/NOPB is suitable for short-reach differential data paths on a backplane where two related channels must be transmitted from one 8-pin SOIC device. Supporting 155.5 Mbps, the driver provides sufficient bandwidth for legacy control, status, or synchronized data interfaces. Its current-mode output is suited to properly terminated LVDS transmission lines, but useful signal integrity depends on connector geometry, dielectric loss, and return-path continuity. Engineers should preserve the recommended differential impedance and avoid adding unmatched stubs that create reflections on the driven lines.

📺

Video and Imaging Data Links

The DS90C401MX/NOPB can transmit two low-power differential data channels associated with video, imaging, or synchronization equipment. The 155.5 Mbps rate is appropriate for compact point-to-point systems that convert lower-speed parallel data and transfer it across a board or chassis boundary. Because LVDS is a physical signaling method rather than a complete video standard, the upstream data source must handle encoding and timing. Differential routing and correct receiver termination should be validated across the worst-case cable and connector conditions to avoid reflections and timing degradation.

🖥️

Server and Network Interface Cards

The DS90C401MX/NOPB can support legacy or proprietary high-speed links on server daughterboards and network interface cards when two low-power differential channels are required. Its 8-pin SOIC package simplifies routing between a controller and remote interface circuitry, while the 4.5 V to 5.5 V supply range supports conventional interface rails. The design must account for connector loss, receiver thresholds, and the transition behavior of the transmitting controller. Use short, impedance-controlled traces or qualified cable interconnects and verify timing margin with realistic loading before treating the link as production-ready.

Resumen de productos recomendados

DS90C402 Complementary dual LVDS receiver Se usa en: DS90C402 Point-to-Point Links, Industrial Data Acquisition, Test and Measurement Systems, Backplane Data Transmission, Video and Imaging Data Links, Server and Network Interface Cards
What is the DS90C401MX/NOPB?
The DS90C401MX/NOPB is a Texas Instruments dual LVDS line driver with two transmit channels and no receiver channels. According to the manufacturer product page, it is optimized for high-data-rate, low-power point-to-point interfaces and uses a balanced current-mode architecture to maintain low power dissipation and reduced short-circuit fault current at high frequency.
What is the operating voltage of DS90C401MX/NOPB?
The DS90C401MX/NOPB operates from 4.5 V to 5.5 V, making it suitable for conventional 5 V digital-interface systems. Texas Instruments describes the device as a dual LVDS driver intended for high-data-rate point-to-point links, with the supply operating range appearing in the manufacturer datasheet and product documentation for the exact device family.
What is the maximum data rate of DS90C401MX/NOPB?
The DS90C401MX/NOPB supports a maximum data rate of 155.5 Mbps. This figure applies to the dual LVDS driver configuration used in high-speed point-to-point links. The value is consistent with the manufacturer description of the DS90C401 as a high-data-rate device and with the exact-part distributor technical listing.
Where can I download the DS90C401MX/NOPB datasheet PDF?
The official DS90C401MX/NOPB datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ds90c401.pdf. The manufacturer datasheet is the primary source for the device description, electrical characteristics, recommended operating conditions, pin assignments, and application information. The manufacturer product page also provides supporting DS90C401 documentation.
Where can I find the DS90C401MX/NOPB pinout?
Use the pin-description table in the Texas Instruments DS90C401 manufacturer datasheet to identify every DS90C401MX/NOPB pin and its function. The exact component is an 8-pin SOIC (D) package. Because the individual pin names are not printed in the accessible product excerpts, this page does not reproduce a potentially misleading connector or signal map.
Can DS90C401MX/NOPB be used with DS90C402?
Yes. Texas Instruments specifically describes the DS90C401 and DS90C402 as a pair-chip solution for a dual high-speed point-to-point interface. The DS90C401MX/NOPB supplies two current-mode LVDS transmit channels, while the DS90C402 provides the complementary receiver function. The receiver’s recommended termination and interface requirements should be followed in the complete reference design.
Where can I buy DS90C401MX/NOPB online?
Use the Request a Quote form on this page to request DS90C401MX/NOPB availability, current commercial terms, and the required packaging configuration. The part is identified by Texas Instruments as an 8-pin SOIC (D) LVDS driver. A written quote request avoids presenting changing inventory or commercial conditions as fixed facts.
What is the price of DS90C401MX/NOPB?
The current commercial price for DS90C401MX/NOPB should be obtained through the Request a Quote form on this page. Pricing can vary with order quantity, tape-and-reel versus cut-tape packaging, and market conditions. The structured pricing fields are reserved for qualifying quantity-break listings and should be consulted for the most current orderable terms.
What is the lead time for DS90C401MX/NOPB?
Request the current DS90C401MX/NOPB lead time and minimum order quantity through the Request a Quote form on this page. Lead time depends on manufacturer inventory, chosen package configuration, order quantity, and production scheduling. Use the manufacturer part-details page to confirm that DS90C401MX/NOPB remains an orderable configuration.
Is DS90C401MX/NOPB in stock?
Current DS90C401MX/NOPB stock should be confirmed through the Request a Quote form on this page. Inventory is time-sensitive and may differ between full-reel, cut-tape, and production-order quantities. The manufacturer part-details page identifies the exact ordering configuration and its 8-pin SOIC package designation.
What can replace DS90C401MX/NOPB?
DS90C401MX is the closest identified drop-in option because it uses the same 8-pin SOIC DS90C401 configuration and appears in an exact cross-reference comparison as fully replaceable without circuit modification. DS90C401M/NOPB is another Texas Instruments ordering configuration to evaluate, but its production and ordering status should be checked before committing it to a design.
Is DS90C401MX/NOPB the same as DS90C401MX?
The DS90C401MX/NOPB and DS90C401MX are variants of the same DS90C401 device family, and the identified comparison describes them as completely replaceable with consistent terminals and package characteristics. The orderable suffix can differ in qualification, packaging, or commercial treatment, so engineers should confirm the specific ordering details and lifecycle status before substitution.
When should I choose DS90C401MX/NOPB over another dual LVDS driver?
Choose DS90C401MX/NOPB when a design needs two current-mode LVDS transmit channels, a 4.5 V to 5.5 V supply, and operation up to 155.5 Mbps in an 8-pin SOIC package. It is particularly suitable when the receiving architecture is based on the DS90C402. A different driver should be selected only if its logic levels, timing, supply range, and termination expectations are independently verified as compatible.
Is DS90C401MX/NOPB suitable for high-speed point-to-point links?
Yes. The DS90C401MX/NOPB is specifically optimized for high-speed point-to-point interfaces, with two LVDS drivers and operation up to 155.5 Mbps. Its balanced current-mode design helps limit power dissipation and short-circuit fault current. Suitability still depends on correct impedance-controlled routing, receiver termination, ground continuity, and signal-integrity verification in the assembled system.
What are the key specifications of DS90C401MX/NOPB that engineers should know?
The principal DS90C401MX/NOPB specifications are two LVDS drivers, a 4.5 V to 5.5 V operating supply, a maximum data rate of 155.5 Mbps, and an 8-pin SOIC (D) package. Texas Instruments describes the output stage as a balanced current-mode driver intended to maintain low power dissipation and minimize short-circuit fault current at high frequency.

Datos de referencia de ingeniería para DS90C401MX/NOPB — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose DS90C401MX/NOPB for a 5 V high-speed interface requiring two LVDS transmit channels, a maximum data rate of 155.5 Mbps, and an 8-pin SOIC footprint. It is a strong choice when the receiver is based on the complementary DS90C402 because Texas Instruments presents the two devices as a matched point-to-point solution. DS90C401MX is the closest identified ordering alternative and may be considered when its qualification and commercial status match the project. DS90C401M/NOPB is another same-family configuration to evaluate, subject to confirmation of its production status and exact ordering conditions. For either alternative, engineers should compare logic thresholds, timing, supply range, and lifecycle requirements rather than relying only on package similarity. None of the identified options changes the fundamental need for controlled-impedance routing, correct LVDS termination, local supply decoupling, and an uninterrupted ground reference.

Comparación con alternativas

Parámetro Este producto DS90C401MX DS90C401M/NOPB
Package 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D)
Brand Texas Instruments Texas Instruments Texas Instruments
Device Type Dual LVDS driver Dual LVDS driver Dual LVDS driver
Number of Drivers 2 2 2
Number of Receivers 0 0 0
Protocol LVDS LVDS LVDS
Output Architecture Balanced current-mode differential driver Balanced current-mode differential driver Balanced current-mode differential driver

Diferenciadores clave

  • Two independent LVDS transmit channels in one package (frente a DS90C401MX)
  • High-speed current-mode operation (frente a DS90C401M/NOPB)
  • Native pairing with DS90C402 receivers (frente a DS90C401M/NOPB)

Notas de diseño

Route each LVDS differential pair as a tightly coupled, impedance-controlled trace pair with a continuous ground reference. Avoid routing over split planes or introducing unmatched stubs, because discontinuities can create reflections that reduce timing margin at data rates up to 155.5 Mbps. Match differential pair spacing and trace geometry to the PCB stack-up, and verify the complete path through connectors or cables.

Place the receiver-side LVDS termination exactly where the manufacturer reference circuit specifies it, close to the receiving device rather than at the transmitter. The DS90C401 uses a current-mode output, so incorrect termination can cause waveform distortion, excessive loading, or unstable common-mode behavior. Validate the differential voltage, rise time, and receiver thresholds across the intended cable length and connector configuration.

Decouple the 4.5 V to 5.5 V supply locally and preserve a low-impedance return path for both differential outputs. Place the recommended input bypass capacitor adjacent to the supply and ground pins, with its ground connection returning directly to the device ground. This arrangement reduces supply disturbance and helps prevent common-mode currents generated by the switching current-mode outputs from coupling into sensitive circuitry.

Do not treat the DS90C401MX/NOPB and DS90C402 as interchangeable transmitter and receiver devices; the former has two drivers and no receivers. Also verify the exact ordering suffix before substituting DS90C401MX or DS90C401M/NOPB. Although the identified cross-reference describes terminal and package compatibility, production status, qualification, and orderable packaging should be checked for the specific procurement cycle.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Yes
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The /NOPB suffix identifies Texas Instruments' lead-free, non-PB-free-package ordering configuration. Detailed RoHS, REACH, halogen-free, AEC-Q100, and conflict-minerals declarations were not available in the accessible exact-part excerpts.

Búsquedas relacionadas

ds90c401mx nopb DS90C401MX/NOPB datasheet DS90C401MX/NOPB pinout DS90C401MX/NOPB datasheet pdf DS90C401MX/NOPB equivalent DS90C401MX/NOPB replacement DS90C401MX/NOPB cross reference DS90C401MX/NOPB price DS90C401MX/NOPB stock Texas Instruments DS90C401MX/NOPB DS90C401MX/NOPB SOIC-8 DS90C401MX/NOPB application circuit

Componentes & términos relacionados

Texas Instruments DS90C401MX/NOPB DS90C401MX DS90C401M/NOPB DS90C402 LVDS Low Voltage Differential Signaling differential line driver current-mode driver balanced differential output interface IC high-speed point-to-point interface 155.5 Mbps 4.5 V to 5.5 V 8-pin SOIC surface mount signal integrity differential impedance LVDS termination lead-free NOPB power dissipation short-circuit fault current continuous ground reference
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ