DS90C401MX/NOPB - Dual LVDS Driver, 155.5 Mbps | Texas Instruments
部品番号: DS90C401MX/NOPB ✓ 生産中DS90C401MX/NOPB 概要
An LVDS driver is a differential signal-line transmitter that uses a balanced current-mode output stage. By steering current between two complementary outputs, the DS90C401 can transmit high-speed digital information while reducing common-mode noise and improving noise immunity over longer point-to-point interconnects. LVDS is part of the broader interface-IC hierarchy, which includes low-voltage differential signaling, differential line drivers, and high-speed serial interface devices.
The current-mode architecture keeps power dissipation relatively low at high operating frequencies and limits the short-circuit fault current. These characteristics make the DS90C401MX/NOPB useful where data must be transferred reliably between circuit boards, rack-mounted equipment, test systems, or other short-reach high-speed links. The dual-driver configuration allows two LVDS channels to be implemented in one package, reducing component count when multiple links are required.
The principal application is a dual point-to-point interface pairing the DS90C401 with one or more DS90C402 receivers. Each driver channel provides complementary differential outputs intended for a properly terminated LVDS transmission line. Designers should use controlled-impedance routing, maintain a continuous ground reference, place termination close to the receiver, and follow the manufacturer’s recommended decoupling and pinout guidance.
The DS90C401MX/NOPB also offers a practical alternative to single-channel driver arrangements when two related high-speed links are needed. Its 4.5 V to 5.5 V operating range supports conventional 5 V interface systems, while the 155.5 Mbps data-rate capability addresses legacy and industrial data links. The /NOPB suffix identifies the lead-free, non-PB-free-package configuration as designated by Texas Instruments.
This page combines the device’s core electrical and packaging characteristics with application guidance, comparison notes, and design considerations. It also identifies the exact DS90C401MX/NOPB manufacturer datasheet and product-page resources for authoritative electrical characteristics, recommended operating conditions, pin assignments, and application schematics.
ドロップイン代替品: DS90C401MX/NOPB — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: DS90C401MX/NOPB (同一形状・フットプリント) — 相違点: Package, Product Type, Driver Architecture.
DS90C401MX
✅ ドロップイン価格はお問い合わせください
データシートを見る →DS90C401M/NOPB
✅ ドロップイン📋 参考代替品(カタログ未掲載)
DS90C401MX/NOPB 仕様
| Device Type | Dual LVDS driver |
| Number of Drivers | 2 drivers |
| Number of Receivers | 0 receivers |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Maximum Data Rate | 155.5 Mbps |
| Protocol | LVDS |
| Output Architecture | Balanced current-mode differential driver |
| パッケージ | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| 実装タイプ | Surface mount |
| Packaging | Tape and reel (TR) or cut tape (CT) |
| 動作温度範囲 | -40°C to +85°C |
| Lead-Free Status | Lead-free / NOPB configuration |
DS90C401MX/NOPB 3.90 mm ピン配置ガイド
DS90C401MX/NOPB (3.90 mm パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: DS90C401MX/NOPB.
詳細は データシート をご参照ください。
主な用途
DS90C401MX/NOPB の用途: 6 件s: DS90C402 Point-to-Point Links, Industrial Data Acquisition, Test and Measurement Systems, Backplane Data Transmission, Video and Imaging Data Links, Server and Network Interface Cards.
DS90C402 Point-to-Point Links
The DS90C401MX/NOPB is designed to pair with the Texas Instruments DS90C402 as a two-channel high-speed point-to-point interface. Its two balanced current-mode LVDS drivers operate from 4.5 V to 5.5 V and support rates up to 155.5 Mbps, allowing one transmitter package to serve two related links. Each output pair should be routed with controlled impedance and terminated in accordance with the receiver circuit. This arrangement is useful when a system needs two data paths without using separate single-channel driver packages, while the current-mode architecture helps maintain low power dissipation at high frequency.
おすすめ
Industrial Data Acquisition
The dual LVDS channels of the DS90C401MX/NOPB suit industrial acquisition equipment that transfers clocked or sampled data between circuit boards. The 155.5 Mbps capability provides margin for moderate-rate parallel-to-serial conversion stages, while differential current-mode signaling improves noise immunity on inter-board links. Designers should maintain a continuous ground plane, use equal-length routing where timing margins require it, and place the receiver termination close to the receiving device. The 4.5 V to 5.5 V supply range also aligns with conventional 5 V industrial interface electronics.
おすすめ
Test and Measurement Systems
The DS90C401MX/NOPB can provide two low-power differential transmit paths in instrumentation and automated test equipment that connects control logic to remote acquisition or processing modules. Its two-driver configuration reduces the number of transmit packages required for a dual-channel system, and the balanced LVDS outputs help prevent common-mode pickup from disturbing sensitive measurements. Designers should characterize the complete channel with the intended receiver, connector, and cable, including propagation delay, jitter, impedance, and termination. Controlled impedance and a continuous ground return are essential for repeatable measurements.
おすすめ
Backplane Data Transmission
The DS90C401MX/NOPB is suitable for short-reach differential data paths on a backplane where two related channels must be transmitted from one 8-pin SOIC device. Supporting 155.5 Mbps, the driver provides sufficient bandwidth for legacy control, status, or synchronized data interfaces. Its current-mode output is suited to properly terminated LVDS transmission lines, but useful signal integrity depends on connector geometry, dielectric loss, and return-path continuity. Engineers should preserve the recommended differential impedance and avoid adding unmatched stubs that create reflections on the driven lines.
おすすめ
Video and Imaging Data Links
The DS90C401MX/NOPB can transmit two low-power differential data channels associated with video, imaging, or synchronization equipment. The 155.5 Mbps rate is appropriate for compact point-to-point systems that convert lower-speed parallel data and transfer it across a board or chassis boundary. Because LVDS is a physical signaling method rather than a complete video standard, the upstream data source must handle encoding and timing. Differential routing and correct receiver termination should be validated across the worst-case cable and connector conditions to avoid reflections and timing degradation.
おすすめ
Server and Network Interface Cards
The DS90C401MX/NOPB can support legacy or proprietary high-speed links on server daughterboards and network interface cards when two low-power differential channels are required. Its 8-pin SOIC package simplifies routing between a controller and remote interface circuitry, while the 4.5 V to 5.5 V supply range supports conventional interface rails. The design must account for connector loss, receiver thresholds, and the transition behavior of the transmitting controller. Use short, impedance-controlled traces or qualified cable interconnects and verify timing margin with realistic loading before treating the link as production-ready.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: DS90C401MX/NOPB — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | DS90C401MX | DS90C401M/NOPB |
|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Dual LVDS driver | Dual LVDS driver | Dual LVDS driver |
| Number of Drivers | 2 | 2 | 2 |
| Number of Receivers | 0 | 0 | 0 |
| Protocol | LVDS | LVDS | LVDS |
| Output Architecture | Balanced current-mode differential driver | Balanced current-mode differential driver | Balanced current-mode differential driver |
主な差別化要因
- Two independent LVDS transmit channels in one package (vs DS90C401MX)
- High-speed current-mode operation (vs DS90C401M/NOPB)
- Native pairing with DS90C402 receivers (vs DS90C401M/NOPB)
設計ノート
Route each LVDS differential pair as a tightly coupled, impedance-controlled trace pair with a continuous ground reference. Avoid routing over split planes or introducing unmatched stubs, because discontinuities can create reflections that reduce timing margin at data rates up to 155.5 Mbps. Match differential pair spacing and trace geometry to the PCB stack-up, and verify the complete path through connectors or cables.
Place the receiver-side LVDS termination exactly where the manufacturer reference circuit specifies it, close to the receiving device rather than at the transmitter. The DS90C401 uses a current-mode output, so incorrect termination can cause waveform distortion, excessive loading, or unstable common-mode behavior. Validate the differential voltage, rise time, and receiver thresholds across the intended cable length and connector configuration.
Decouple the 4.5 V to 5.5 V supply locally and preserve a low-impedance return path for both differential outputs. Place the recommended input bypass capacitor adjacent to the supply and ground pins, with its ground connection returning directly to the device ground. This arrangement reduces supply disturbance and helps prevent common-mode currents generated by the switching current-mode outputs from coupling into sensitive circuitry.
Do not treat the DS90C401MX/NOPB and DS90C402 as interchangeable transmitter and receiver devices; the former has two drivers and no receivers. Also verify the exact ordering suffix before substituting DS90C401MX or DS90C401M/NOPB. Although the identified cross-reference describes terminal and package compatibility, production status, qualification, and orderable packaging should be checked for the specific procurement cycle.
コンプライアンス情報
The /NOPB suffix identifies Texas Instruments' lead-free, non-PB-free-package ordering configuration. Detailed RoHS, REACH, halogen-free, AEC-Q100, and conflict-minerals declarations were not available in the accessible exact-part excerpts.