ICS511MT - 200MHz PLL Clock Generator | Renesas Electronics
N.º de pieza: ICS511MT ✗ Fin de vidaICS511MT Descripción general
A PLL clock generator, also called a frequency multiplier or clock synthesizer, belongs to the clock and timing IC category. It uses a phase-locked loop to derive an output frequency from a reference source. The reference can be a crystal oscillator or external clock, and the generated CMOS output is suitable for systems requiring a higher-frequency operating clock than the source provides.
Key features of the ICS511MT include PLL clock multiplication, a maximum frequency of 200 MHz, one clock circuit, CMOS output, and support for both crystal and clock inputs. The 1:1 input-to-output ratio is listed for the device, while the PLL architecture provides a practical route to generating a high-frequency clock from a lower-frequency reference. Its single-circuit configuration suits designs requiring one multiplied clock rather than multiple independently generated outputs.
Technically, the ICS511MT is intended for clock generation where the output must be derived from a stable reference. The use of a crystal input supports designs that require predictable frequency behavior, while clock input support allows the device to operate from an existing system reference. The CMOS output interface makes it relevant to digital logic, processor, communications, and embedded-control systems requiring a high-speed clock signal.
Typical applications include clocking for digital processors, communications equipment, test and measurement systems, embedded control platforms, and general-purpose digital logic. The device can reduce the need for multiple external clock-generation solutions when a single high-frequency CMOS clock is sufficient. Its principal benefit is clock multiplication in a small 8-SOIC package, although board-level stability, jitter, supply requirements, and output-drive limits must be checked against the manufacturer datasheet before finalizing a design.
For PCB implementation, place the device close to the crystal, decoupling capacitors, and clock-consuming circuits to minimize trace length and noise pickup. Follow the manufacturer’s recommended crystal load-capacitance network, provide stable supply decoupling, and route the output as a short, controlled-impedance clock trace. Confirm pin orientation, operating limits, and crystal requirements directly from the manufacturer datasheet and the package drawing.
This product summary combines the device’s identified LOCO PLL architecture, 200 MHz maximum frequency, CMOS output, input options, package format, sourcing context, and practical clock-tree design considerations to support faster component selection and PCB planning.
Alternativas directas para ICS511MT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
ICS511MIT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ICS511MI
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ICS511MILFT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ICS511MLFT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ICS511M
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →ICS511MT Especificaciones
| Product Type | Clock Generator IC |
| PLL | Yes |
| Input Type | Clock, Crystal |
| Tipo de salida | CMOS |
| Maximum Frequency | 200 MHz |
| Number of Circuits | 1 |
| Input-to-Output Ratio | 1:1 |
| Differential Input | No |
| Differential Output | No |
| Encapsulado | 8-SOIC, 0.154 inch, 3.90 mm width |
| Architecture | LOCO PLL clock multiplier |
| Reference Source | Crystal or external clock |
| Output Logic | CMOS |
| Tipo de montaje | Surface Mount |
| Estado del ciclo de vida | Obsolete |
Guía de configuración de pines de ICS511MT 8-soic, 0.154 inch, 3.90 mm width
Configuración de pines para ICS511MT (encapsulado 8-soic, 0.154 inch, 3.90 mm width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ICS511MT.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ICS511MT es adecuado para 6 aplicacións: Digital Processor Clocking, Communications Equipment, Embedded Control Systems, Test and Measurement Instrumentation, Industrial Data Acquisition, General-Purpose Digital Logic.
Digital Processor Clocking
The ICS511MT is suited to digital processor clock trees that require a CMOS clock up to 200 MHz derived from a crystal or another clock reference. Its PLL architecture provides frequency multiplication without requiring a separate high-frequency oscillator for every rail. Place the device near the crystal and processor clock input, use the manufacturer-recommended load network, and route the clock output as a short trace. The design must also verify processor setup and hold timing, clock jitter, supply range, and output loading before treating the 200 MHz rating as a complete timing guarantee.
Recomendado
Communications Equipment
The ICS511MT can support communications equipment that needs a stable, high-frequency CMOS clock from a lower-frequency reference. A single PLL clock generator is useful when the board already has a reference source but requires a derived clock for digital signal-processing or interface logic. Keep the reference path short, provide local supply decoupling, and maintain controlled return paths beneath the clock route. Because communications timing can be sensitive to jitter and edge quality, verify the manufacturer’s jitter, output-rise-time, and loading characteristics against the actual downstream device requirements.
Recomendado
Embedded Control Systems
ICS511MT is applicable to embedded-control boards that distribute a CMOS clock to one or more digital logic blocks. Its one-circuit architecture is efficient for a single-clock design, while crystal input support allows the clock generator to serve as the central element of a compact reference network. The board should separate sensitive clock routing from noisy switching nodes, use a solid ground reference, and observe the manufacturer’s crystal load-capacitance calculation. Confirm supply-voltage tolerance and maximum operating frequency for the selected controller before production release.
Recomendado
Test and Measurement Instrumentation
The 200 MHz maximum frequency and CMOS output make ICS511MT relevant to instrumentation clock distribution where a common high-speed reference is needed for counters, converters, or digital control logic. A PLL-based arrangement can consolidate multiple frequency requirements around one reference source, but the exact multiplication ratio and operating conditions must be checked against the device specification. Use short, impedance-controlled clock traces and avoid placing the output route beside high-energy switching nodes. Probe loading and measurement grounding should also be considered during board validation.
Recomendado
Industrial Data Acquisition
ICS511MT can fit industrial data-acquisition systems requiring a deterministic CMOS clock for control, conversion, and communication logic. Its PLL-based reference arrangement can reduce the number of separate oscillator components while supporting either crystal or external-clock operation. Industrial equipment should account for temperature range, supply tolerance, startup behavior, and electromagnetic compatibility at the system level. Place the clock generator close to the reference source, provide the recommended bypass capacitors, and route the output away from switching power stages to minimize coupling.
Recomendado
General-Purpose Digital Logic
For general-purpose digital logic, ICS511MT provides a single CMOS clock output with PLL-based multiplication capability and a maximum listed frequency of 200 MHz. It is most useful when a board already has a stable reference clock and needs a derived output without implementing a high-frequency oscillator network directly on the PCB. Follow the manufacturer’s power-pin and decoupling guidance, confirm input and output logic levels, and reserve the crystal footprint only when the chosen reference configuration requires it. Validate edge quality and load behavior at the intended clock frequency.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ICS511MT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ICS511MIT | ICS511MI | ICS511MILFT | ICS511MLFT | ICS511M |
|---|---|---|---|---|---|---|
| Package | 8-SOIC, 3.90 mm width | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Device Type | Clock Generator IC | Clock Generator IC | Clock Generator IC | Clock Generator IC | Clock Generator IC | Clock Generator IC |
Diferenciadores clave
- Higher stated maximum clock frequency than ICS511MI (frente a ICS511MI)
- Broad reference-source support (frente a ICS511MIT)
- Single-output CMOS clock architecture (frente a ICS511MI)
Notas de diseño
Place the ICS511MT near the crystal and clock-consuming circuitry, and keep the clock output trace short. Use a continuous ground reference beneath the clock path, avoid routing parallel to noisy power-converter nodes, and use the manufacturer’s recommended crystal load network. Confirm the 8-SOIC pin orientation and land pattern against the package drawing before fabrication.
Treat the CMOS clock output as a high-speed signal: use a short route, minimize stubs, provide a nearby return path, and maintain consistent geometry where the clock crosses a board boundary. Validate rise time, overshoot, ringing, and downstream load in simulation or with an oscilloscope. The 200 MHz maximum-frequency rating alone does not establish timing margin for a particular receiver.
Do not select an ICS511-family substitute from the series name alone. Confirm the exact MPN, pin assignment, input-source configuration, maximum frequency, supply range, and delivery suffix against the manufacturer datasheet. In particular, ICS511MI is listed at 160 MHz versus 200 MHz for ICS511MT, making it unsuitable for designs that require the full target frequency.
Follow the manufacturer’s power-pin connection and decoupling layout for the ICS511MT. Place the required bypass capacitor immediately adjacent to the device supply pin and provide an unobstructed ground return. Check the device’s current consumption and supply operating limits in the datasheet; those values were not present in the available product summaries and must not be assumed for a new design.
Información de cumplimiento
Compliance status was not stated in the available product listings. Check the manufacturer datasheet and current material-compliance documentation before new production approval.