Renesas Electronics

ICS570AT - 170MHz Spread Spectrum Clock | Renesas

N.º de pieza: ICS570AT ✓ Activo
8-SOIC, 0.154 inch body width, 3.90 mm width Package 170 MHz Speed
MOQ: 1 |

ICS570AT Descripción general

The Renesas Electronics ICS570AT is a 170 MHz fanout-distribution clock generator and zero-delay buffer (ZDB) integrated into a 8-SOIC package. It combines a clock-generation function with fanout distribution and zero-delay buffering, allowing a system to multiply, distribute, and buffer a reference clock while controlling the relationship between input and output edges. The device is identified as a spread-spectrum clock generator for applications where controlled clock-spectrum spreading can reduce narrowband emissions.

A zero-delay buffer is an integrated timing device that compensates for the propagation delay introduced by clock fanout networks. By placing the buffer close to the load or in the fanout path, the device helps preserve edge alignment between clock outputs. The ICS570AT integrates this clock-distribution role with analog/digital phase-locked-loop technology, a technique also used in multiplier-based clocking solutions.

The principal documented characteristics of the ICS570AT are its 170 MHz operating class, spread-spectrum clock-generator function, zero-delay-buffer function, fanout-distribution capability, and 8-SOIC surface-mount package. These characteristics place it in the clock and timing hierarchy between a single reference oscillator and the multiple clock domains required by processors, converters, transceivers, and memory interfaces.

The ICS570AT is useful when a board requires more than a passive clock fanout buffer. Passive fanout devices introduce insertion delay and may not compensate for load-dependent skew, while the integrated PLL-based architecture in the ICS570AT is intended to regenerate and distribute a clock with phase adjustment. The spread-spectrum feature adds another design tool for systems where reducing concentrated spectral peaks is a priority.

Typical uses include audio and network interface clocking, digital signal processing subsystems, data-conversion equipment, communications modules, and industrial control boards. In these systems, the device can drive downstream clock-consuming circuits from a shared reference while keeping clock edges aligned across multiple branches.

When laying out a design around the ICS570AT, follow the pin-description table and recommended decoupling network in the Renesas 570 datasheet. Keep the clock output traces short, use controlled-impedance routing, and avoid placing noisy switching nodes beneath the device. Confirm the selected spread-spectrum profile, output count, and timing budget against the system requirement before releasing the layout.

This page combines the manufacturer datasheet information with package-level guidance, application context, comparison parameters, and practical layout considerations. It is intended to help engineers evaluate the ICS570AT as a drop-in clock-distribution choice and to identify the checks required before substituting another PLL or zero-delay-buffer device.

Alternativas directas para ICS570AT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

570ALFT

✅ Sustitución directa
📦 SOIC-8
Same SOIC-8 footprint and PLL-based clock-driver function; nominal clock class differs from 170 MHz by an amount that requires datasheet confirmation

📋 Alternativa de referencia (no en el catálogo)

ICS570BLT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-8
Same 570-series SOIC-8 clock topology; suffix-specific operating point differs from the 170 MHz ICS570AT configuration

📋 Alternativa de referencia (no en el catálogo)

ICS570CLT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-8
Same 570-series SOIC-8 pin and clock-distribution architecture; suffix-specific frequency or spread-spectrum setting differs from ICS570AT

📋 Alternativa de referencia (no en el catálogo)

ICS570ELT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-8
Same 570-series SOIC-8 package and PLL-based distribution function; operating configuration differs from the 170 MHz ICS570AT

📋 Alternativa de referencia (no en el catálogo)

ICS570FLT

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-8
Same 570-series SOIC-8 footprint and clock-generation class; suffix-specific operating parameters differ from ICS570AT

📋 Alternativa de referencia (no en el catálogo)

ICS570AT Especificaciones

Manufacturer Renesas Electronics Corporation
Device Type Fanout distribution, spread spectrum clock generator, zero delay buffer
Frecuencia de reloj máxima 170 MHz
Clock Architecture Multiplier and zero-delay buffer
PLL Technique Proprietary analog/digital phase-locked loop
Spread Spectrum Modulation Spread spectrum clock generation
Encapsulado 8-SOIC, 0.154 inch body width, 3.90 mm width
Tipo de montaje Surface mount
Recuento de pines 8 pins

Guía de configuración de pines de ICS570AT 8-soic, 0.154 inch body width, 3.90 mm width

Configuración de pines para ICS570AT (encapsulado 8-soic, 0.154 inch body width, 3.90 mm width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 8-soic, 0.154 inch body width, 3.90 mm width para ICS570AT

No hay datos detallados de patillaje disponibles para ICS570AT.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

ICS570AT es adecuado para 6 aplicacións: Audio Codec and Converter Clocking, Network Interface and Data-Converter Clock Trees, Industrial Control and Automation Boards, Communications Module and RF-Front-End Support, Server and Storage Controller Clock Distribution, Test and Measurement Instrumentation.

🎧

Audio Codec and Converter Clocking

The ICS570AT fits audio subsystems that require a regenerated clock rather than a passive fanout path. Its documented 170 MHz operating class, zero-delay-buffer function, and spread-spectrum capability provide a clock source for converters, digital audio interfaces, and downstream processing logic. Placing the device near the audio clock loads allows the PLL-based architecture to compensate for routing delay and keep branch edges aligned. Spread-spectrum operation can also reduce concentrated narrowband clock energy, which is useful when the audio board must share a dense chassis with switching regulators and high-speed digital circuits.

🌐

Network Interface and Data-Converter Clock Trees

The ICS570AT is appropriate for communications boards that distribute a common reference to converters, serializers, and interface controllers. A zero-delay buffer can offset the propagation delay introduced by traces, vias, and fanout loads, while the integrated PLL-based approach regenerates the clock instead of simply passing it through. The 170 MHz device class supports high-speed digital subsystems, and spread-spectrum generation offers additional control over clock-related spectral peaks. Engineers should verify the reference ratio, output arrangement, and jitter requirement for the specific Ethernet, storage, or backplane interface being clocked.

🏭

Industrial Control and Automation Boards

Industrial control boards often distribute one reference clock among processors, transceivers, and data-conversion circuits while also containing switching regulators and motor-control drivers. The ICS570AT's integrated zero-delay buffering helps compensate for clock-branch delay, and its spread-spectrum clock-generator function provides a way to reduce narrowband clock emissions. The 8-SOIC surface-mount package is practical for multilayer control boards where component area is limited. Confirm the industrial temperature requirement and the exact spread-spectrum configuration in the Renesas 570 datasheet before the part is specified for a deployed control platform.

📡

Communications Module and RF-Front-End Support

The ICS570AT can support the digital clock tree beneath a communications module by regenerating and distributing a reference with compensated edge timing. This is useful when a transceiver, converter, and digital processor must operate from related clock phases but are separated by unequal trace lengths. The zero-delay-buffer function addresses delay introduced along those branches, while spread-spectrum operation reduces the concentration of energy at one clock frequency. Because RF systems are sensitive to clock harmonics and spurs, engineers should evaluate the modulation profile and output spectrum together with the module's own emissions requirements.

🖥️

Server and Storage Controller Clock Distribution

Server and storage designs need multiple clock branches to remain synchronized across processors, memory interfaces, and data converters. The ICS570AT can serve as a regenerating fanout and zero-delay element when a board requires more control than a passive buffer offers. Its 170 MHz operating class and spread-spectrum-generation capability make it relevant to high-speed digital subsystems, while the compact 8-SOIC package simplifies routing between clock sources and loads. Deployment in server-class equipment still requires verification of the reference ratio, jitter budget, temperature grade, and system-level clock architecture.

🧩

Test and Measurement Instrumentation

Precision instrumentation can benefit from a regenerated clock when multiple converters and digital processors must sample from related timing phases. The ICS570AT integrates clock generation, fanout distribution, and zero-delay compensation, allowing unequal routing delays to be compensated more effectively than with passive fanout. Spread-spectrum operation may also be useful in compact instruments that must meet strict emissions limits. For measurement accuracy, the engineer must still check the device's jitter, reference-input range, output skew, and isolation requirements against the acquisition system's timing budget.

What is the ICS570AT clock generator used for?
The ICS570AT is a 170 MHz fanout-distribution, spread-spectrum clock generator and zero-delay buffer in an 8-SOIC package. According to the Renesas 570 datasheet, it combines multiplier-based clock generation with zero-delay buffering so that a reference clock can be regenerated, distributed, and phase-aligned across multiple downstream loads. The device is suited to systems in which passive fanout delay or clock-branch skew would otherwise compromise timing.
Is the ICS570AT a zero-delay buffer or a clock generator?
The ICS570AT performs both functions in one package. The Renesas product listing identifies it as a fanout-distribution, spread-spectrum clock generator and zero-delay buffer, while the 570 datasheet describes its multiplier-and-ZDB architecture. The integrated PLL-based design compensates for the delay of the clock distribution path rather than simply passing edges through a passive buffer.
What is the operating frequency of the ICS570AT?
The ICS570AT is specified as a 170 MHz clock device. This figure comes from the Renesas and DigiKey product descriptions, which identify the part as a 170 MHz fanout distribution, spread-spectrum clock generator, and zero-delay buffer. Input-range limits, output-frequency tolerance, and maximum jitter must be confirmed against the operating conditions in the Renesas 570 datasheet before the device is approved for a new clock tree.
Where can I download the ICS570AT datasheet PDF?
The official Renesas 570 datasheet is available from the manufacturer document page at https://www.renesas.com/document/dst/570-datasheet. Use that document for the authoritative pin-description table, recommended application circuit, electrical characteristics, spread-spectrum configuration, and layout guidance. The manufacturer document is the preferred source whenever a distributor listing conflicts with the data sheet.
Where can I find the ICS570AT pinout?
The ICS570AT uses an 8-SOIC package, and its authoritative pin assignment is shown in the pin-description table of the Renesas 570 datasheet. The package has eight leads, but no complete pin-name mapping is published in the available product listing. Use the manufacturer diagram when assigning PCB nets, especially for supply, ground, reference input, feedback, and clock outputs.
What are the main advantages of the ICS570AT over a passive clock fanout buffer?
The ICS570AT provides clock regeneration and phase compensation in addition to distribution, whereas a passive fanout buffer only routes the incoming edge and adds insertion delay. The Renesas 570 datasheet describes the ICS570AT as a multiplier and zero-delay buffer using analog/digital PLL techniques, which helps reduce clock-branch delay and maintain edge alignment. It also adds spread-spectrum generation for emission-control applications.
What is the best drop-in replacement for the ICS570AT?
The closest documented alternative is the Renesas 570ALFT, which is listed as a PLL-based clock driver in an 8-SOIC package. A qualified replacement must match the pin assignment, supply voltage, reference-input configuration, output count, feedback topology, and spread-spectrum requirements. Use the ICS570AT and 570ALFT datasheets together, then request a quote through the Request a Quote form on this page for current sourcing.
Can the 570ALFT replace the ICS570AT in an existing PCB design?
The 570ALFT is a candidate rather than an automatic substitute because the two parts are not confirmed to be identical in every timing and configuration parameter. Both are associated with the Renesas 570 clock family and an 8-SOIC format, but the available comparison data indicates that functional characteristics can differ while the circuit structure remains similar. Confirm the complete pin and parameter lists before substitution.
When should I choose the ICS570AT instead of a standard PLL clock driver?
Choose the ICS570AT when the design specifically needs spread-spectrum generation combined with zero-delay fanout in an 8-SOIC package. A standard PLL driver may be preferable when the application does not require spectrum spreading or when another package, output count, or reference ratio better matches the system. The decision should follow the required clock topology, not merely the maximum clock frequency.
Is the ICS570AT suitable for audio and network interface clocking?
The ICS570AT is suitable for clocking subsystems that require regenerated, distributed signals, including audio converters and communications interfaces. Its 170 MHz operating class, zero-delay-buffer function, and spread-spectrum capability make it relevant to noise-sensitive and EMI-conscious designs. Confirm the required reference ratio, output count, and jitter budget against the application clock specification before selection.
Does the ICS570AT support spread-spectrum clock generation?
Yes. The ICS570AT is identified by Renesas and DigiKey as a spread-spectrum clock generator as well as a fanout-distribution and zero-delay-buffer device. Spread-spectrum operation distributes clock energy across a range of frequencies instead of concentrating it at one narrow spectral band. Configure and verify the modulation profile using the settings described in the Renesas 570 datasheet.
Where can I buy the ICS570AT online?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and delivery schedule for the ICS570AT. Distributor listings identify the part as a Renesas 8-SOIC clock device, but availability and commercial terms change frequently. Submitting the quote request keeps the purchasing decision tied to the current manufacturer and distribution channel status.
What is the lead time for the ICS570AT?
The current lead time is not published in the available product information and can vary with order quantity and market conditions. Request the present lead time, minimum order quantity, and schedule through the Request a Quote form on this page. For production planning, treat any preliminary distributor listing as a product-identification source rather than a firm scheduling commitment.
Is the ICS570AT available in stock?
The ICS570AT is listed by multiple distributors, which indicates that the part is an active, orderable catalog item. Stock quantity changes continuously and may differ by package suffix, so use the Request a Quote form on this page for the current inventory and delivery position. This avoids relying on a stale listing status at the time of purchase.
What should I check before laying out a PCB for the ICS570AT?
Verify the pin assignment, supply connections, clock-output mapping, and feedback configuration in the Renesas 570 datasheet before routing the board. Place decoupling capacitors close to the supply pins, keep the reference and clock-output paths short, and use a solid ground reference to control return current. Validate the final topology and spread-spectrum settings against timing and emissions requirements.
What can replace the ICS570AT?
The Renesas 570ALFT is a documented 8-SOIC clock-driver candidate, and other 570-series frequency or spread-spectrum options may fit related clock trees. The best replacement is the device that matches the required operating frequency, spread-spectrum profile, output configuration, supply voltage, and pinout without changing the PCB. Validate every parameter against the manufacturer documentation and the original design constraints.

Datos de referencia de ingeniería para ICS570AT — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the ICS570AT when the clock tree requires a 170 MHz-class device that combines PLL-based generation, zero-delay buffering, fanout distribution, and spread-spectrum operation in an 8-SOIC package. Consider the 570ALFT when a Renesas PLL clock driver matches the reference ratio, outputs, feedback arrangement, and timing budget more closely; the available comparison indicates related functionality but not complete electrical equivalence. The other 570-series options may suit different frequency or spread-spectrum configurations, but their suffix-specific operating parameters must be confirmed from the manufacturer documentation before they are treated as drop-in replacements. In every case, verify pinout, supply voltage, output count, jitter, skew, and operating temperature. If the design does not require spread-spectrum regeneration, a simpler clock generator or passive fanout arrangement may be more appropriate.

Comparación con alternativas

Parámetro Este producto 570ALFT ICS570BLT ICS570CLT ICS570ELT ICS570FLT
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package SOIC-8 SOIC-8 - same package SOIC-8 - same package SOIC-8 - same package SOIC-8 - same package SOIC-8 - same package
Device Function Fanout distribution, spread-spectrum clock generator, zero delay buffer PLL-based clock driver 570-series clock generation and distribution 570-series clock generation and distribution 570-series clock generation and distribution 570-series clock generation and distribution
Zero-Delay Buffer Function Yes PLL-based clock driver with zero-delay capability 570-series zero-delay clock function 570-series zero-delay clock function 570-series zero-delay clock function 570-series zero-delay clock function
PLL Architecture Proprietary analog/digital PLL PLL-based 570-series PLL-based architecture 570-series PLL-based architecture 570-series PLL-based architecture 570-series PLL-based architecture

Diferenciadores clave

  • Combines clock generation, fanout, and zero-delay compensation in one device (frente a 570ALFT)
  • Documented 170 MHz operating class (frente a ICS570BLT)
  • Compact 8-SOIC implementation for mixed clock-tree functions (frente a 570ALFT)

Notas de diseño

Follow the Renesas 570 datasheet reference layout for bypass capacitors and place them immediately beside the relevant supply and ground pins. Route clock outputs as short, controlled-impedance traces and avoid stubs or test-probe connections on sensitive edges. A solid ground plane beneath the device reduces return-path discontinuities and helps maintain predictable clock-edge timing.

Treat the reference input as a high-quality clock signal rather than an ordinary logic input. Use a short source path, keep the PLL loop in close proximity to the device, and avoid routing the reference beneath noisy digital or power-converter traces. Confirm the configured operating point and allowable input slew before relying on stable phase lock across temperature and supply variations.

Do not select a 570-series replacement from the package marking alone. The output arrangement, spread-spectrum profile, reference ratio, feedback arrangement, and electrical limits must be compared between the original and replacement datasheets. A same-package part can still require schematic changes if its reference, feedback, or enable connections differ from those of the ICS570AT.

Spread-spectrum clocking can broaden the fundamental clock energy, but it does not remove harmonics or unrelated board noise. Evaluate both the configured modulation profile and the measured output spectrum with the final clock loads and PCB in place. Keep switching-regulator loops and high-di/dt nets away from the clock outputs to avoid adding modulation products to the spread clock spectrum.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The available product information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Check the Renesas 570 datasheet and the current manufacturer material-declaration records before environmental or automotive qualification.

Datos verificados el: 2026-11-11 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

ICS570AT datasheet ICS570AT pinout ICS570AT datasheet pdf ICS570AT equivalent ICS570AT replacement ICS570AT cross reference ICS570AT vs 570ALFT ICS570AT 170MHz clock generator ICS570AT SOIC-8 footprint ICS570AT spread spectrum clock ICS570AT zero delay buffer ICS570AT application circuit Renesas ICS570AT ICS570AT price ICS570AT stock

Componentes & términos relacionados

Renesas Electronics ICS570AT 570ALFT ICS570BLT ICS570CLT ICS570ELT ICS570FLT clock generator clock distribution zero-delay buffer ZDB phase-locked loop PLL spread spectrum clock multiplier SOIC-8 surface mount 170 MHz clock reference input feedback EMI control audio clocking network interface clocking industrial control
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ