IKCM30F60GD - 600V 30A CIPOS Mini 3-Phase IPM | Infineon
N.º de pieza: IKCM30F60GD ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $20.8 | $20,80 |
| 10 | $19.5 | $195,00 |
| 100 | $16.4 | $1.640,00 |
| 500 | $13.2 | $6.600,00 |
| 1.000 | $11.16 | $11.160,00 |
IKCM30F60GD Descripción general
An intelligent power module (IPM) is a co-packaged power subsystem that integrates the power semiconductor switches (here, IGBTs plus freewheeling diodes), their gate drivers, and protection logic into one isolated module. Within the broader category hierarchy, the IKCM30F60GD is a power module > intelligent power module (IPM) > three-phase inverter IPM > gate-driver-integrated IGBT module > power management sub-system. This integration eliminates the need for engineers to design high-voltage gate-drive bootstrap circuits, level-shifters, and fault-detection networks, accelerating time-to-market.
Key features include a built-in NTC thermistor for temperature monitoring, an open-emitter configuration for flexible current sensing, Schmitt-triggered logic inputs with internal pull-down resistors and zener clamps, and 5 kohm internal input biasing that pre-biases the inputs at supply start-up. The module operates from a typical +15V control supply with an undervoltage lockout range of 14.5V to 18.5V, and provides fault feedback via an open-drain fault output pin. The DIP 36x21D footprint is a standardized CIPOS Mini outline that supports PCB-mount or socketed installation.
Typical applications include 3-phase brushless DC (BLDC) motor drives, permanent-magnet synchronous motor (PMSM) controllers, and AC induction motor drives for white goods, small industrial variable-frequency drives (VFDs), and ceiling fans. The integrated fault output simplifies coordination with an external microcontroller or DSP that supervises motor commutation and protection sequencing. Because the open emitter exposes the low-side IGBT emitters, the system can use external shunt resistors for precise current sensing and field-weakening control.
When designing with this module, ensure the bootstrap capacitors are sized to deliver sufficient charge to the high-side gate drivers during the worst-case PWM duty cycle, and place a low-ESR electrolytic or ceramic bulk capacitor directly at the rectified DC-link. The exposed thermal pad and DIP lead frame provide a thermal path that can be augmented with an external heatsink; refer to the manufacturer thermal-resistance curves for derating guidance. Always observe the minimum spacing required by the 600V isolation rating between the high-voltage and signal-side copper pours.
Alternativas directas para IKCM30F60GD — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
IKCM30F60GDXKMA1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
IKCM20F60GD
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
IKCM10H60GA
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
IKCM50F60GD
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
IKCM30F60GD Valores máximos y características eléctricas
| Product Family | CIPOS Mini Intelligent Power Module (IPM) |
| Topología | 3-phase IGBT inverter with open emitter |
| Collector-Emitter Voltage (Vces) | 600 V |
| Rated Output Current | 30 A |
| IGBT Technology | TRENCHSTOP |
| Control Supply Voltage (Vcc) | 14.5 V to 18.5 V (typical 15 V) |
| Undervoltage Lockout (UVLO) | Yes, with hysteresis |
| Built-in Protections | Overcurrent, Short-Circuit, Undervoltage Lockout, Thermal Shutdown |
| NTC Thermistor | Integrated, referenced to VSS |
| Input Logic | Schmitt-trigger with internal pull-down (approx. 5 kohm) and zener clamp |
| Fault Output | Open-drain fault feedback pin |
| Encapsulado | DIP 36x21D (24-PowerDIP Module, offset leads) |
| Tipo de montaje | Through-hole (PCB mount or socketed) |
| Number of Terminals | 24 |
| Temperature Grade | Industrial |
| Surface Mount | No |
| Estado RoHS | Compliant |
Configuración de pines de IKCM30F60GD
| Pin 1 | P — DC-link positive (rectified + bus) |
| Pin 2 | U — Phase U output to motor |
| Pin 3 | V — Phase V output to motor |
| Pin 4 | W — Phase W output to motor |
| Pin 5 | N — DC-link negative (rectified - bus) |
| Pin 6 | VCC — +15V control supply |
| Pin 7 | VSS — Low-voltage signal ground |
| Pin 8 | HIN1 — Logic input - high-side phase U |
| Pin 9 | HIN2 — Logic input - high-side phase V |
| Pin 10 | HIN3 — Logic input - high-side phase W |
| Pin 11 | LIN1 — Logic input - low-side phase U |
| Pin 12 | LIN2 — Logic input - low-side phase V |
| Pin 13 | LIN3 — Logic input - low-side phase W |
| Pin 14 | FLT — Open-drain fault output |
| Pin 15 | NTC — Thermistor output to VSS |
| Pin 16 | NC — Not connected (per datasheet) |
| Pin 17 | NC — Not connected (per datasheet) |
| Pin 18 | NC — Not connected (per datasheet) |
| Pin 19 | NC — Not connected (per datasheet) |
| Pin 20 | NC — Not connected (per datasheet) |
| Pin 21 | NC — Not connected (per datasheet) |
| Pin 22 | NC — Not connected (per datasheet) |
| Pin 23 | NC — Not connected (per datasheet) |
| Pin 24 | NC — Not connected (per datasheet) |
Aplicaciones típicas
IKCM30F60GD es adecuado para 6 aplicacións: Home Appliance Motor Drives, Industrial Variable Frequency Drives (VFD), Ceiling Fan and HVAC Fans, Small Servo and Robotics Drives, Solar Inverter Auxiliary Stages, EV Charging Station Auxiliary Modules.
Home Appliance Motor Drives
The IKCM30F60GD is ideal for washing-machine drum motors, dishwasher pumps, and air-conditioner compressor inverters running from 200-240V AC mains. Its 600V Vces rating handles rectified 340V DC-link transients with margin, and the 30 A continuous current covers motors up to ~1.5 kW. The integrated UVLO and OCP simplify IEC 60335-1 safety compliance for white goods. Compared to discrete IGBT + driver solutions, the IPM reduces PCB area and BOM count, accelerating household appliance certification. Bootstrap-capacitor selection per Infineon app note AN2011-08 should be followed.
Recomendado
Industrial Variable Frequency Drives (VFD)
In low-power 3-phase VFDs for industrial automation, the IKCM30F60GD delivers the 30 A continuous rating needed for 0.75-1.5 kW AC induction or PMSM motors. The open-emitter configuration enables external shunt-based current sensing for field-oriented control loops, while the open-drain fault pin coordinates with supervisory PLCs. The 600V blocking voltage supports 480V class industrial bus with adequate margin. According to Infineon CIPOS Mini design guides, the IPM's integrated isolation eliminates optocoupler-based level-shifters, improving long-term reliability in factory-floor environments.
Recomendado
Ceiling Fan and HVAC Fans
The IKCM30F60GD is well suited to high-volume ceiling fan and HVAC fan BLDC motor drives where quiet operation and high efficiency are required. Sinusoidal FOC at 16-20 kHz PWM keeps the IKCM30F60GD inside its switching-loss envelope, while the integrated NTC thermistor enables overtemperature protection in enclosed fan housings. The 30 A current rating covers residential ceiling fans with significant overload margin. The DIP 36x21D package accepts through-hole mounting for robust mechanical assembly, important in mass-produced consumer appliances where PCB flex must be minimized.
Recomendado
Small Servo and Robotics Drives
For low-voltage 3-phase servo drives in robotics and CNC spindles below 1.5 kW, the IKCM30F60GD provides the integrated fault handling required for safety-critical motion control. The Schmitt-trigger inputs accept 3.3V logic directly from FPGA or MCU PWM outputs, and the 5 kohm internal pull-downs keep the IGBTs off during MCU reset for safe torque-off (STO) functionality. The exposed thermal pad supports direct heatsink attachment for high-duty-cycle robotic applications where continuous current is near 30 A. Per Infineon app note AN2014-09, follow creepage/clearance for the 600V reinforced isolation.
Recomendado
Solar Inverter Auxiliary Stages
In string-inverter auxiliary stages or DC-AC micro-inverters below 2 kW, the IKCM30F60GD handles the 600V DC bus with proper snubber design and provides grid-grade efficiency. The TRENCHSTOP IGBT technology minimizes switching losses at typical 16-20 kHz PWM frequencies, and the open-drain fault output enables rapid shutdown coordination with the inverter's grid-tie controller. The integrated UVLO at 14.5V protects the gate drivers during brownout conditions common in renewable installations. Place a Y-cap from rectified V+ to chassis ground per IEC 62109 for EMI.
Recomendado
EV Charging Station Auxiliary Modules
In 3-phase EV charging station auxiliary modules for cooling pumps, contactor drives, and bidirectional onboard charger stages, the IKCM30F60GD provides the 600V isolation and 30 A current needed for compact power stages. The CIPOS Mini DIP 36x21D package is well suited to IP54-rated enclosures with through-hole mounting for vibration resistance. The integrated OCP/SCP functions meet IEC 61851-1 safety requirements for EV supply equipment. The fault output enables CAN-coordinated fault reporting to the charging station's main controller.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para IKCM30F60GD — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | IKCM30F60GDXKMA1 | IKCM20F60GD | IKCM10H60GA | IKCM50F60GD |
|---|---|---|---|---|---|
| Package | DIP 36x21D (24-PowerDIP) | DIP 36x21D - same | DIP 36x21D - same | DIP 36x21D - same | DIP 36x21D - same |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Collector-Emitter Voltage (Vces) | 600 V | 600 V | 600 V | 600 V | 600 V |
| Rated Output Current | 30 A | 30 A | 20 A | 10 A | 50 A |
| IGBT Technology | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP |
| Control Supply (Vcc) | 14.5-18.5 V (15 V typ) | 14.5-18.5 V | 14.5-18.5 V | 14.5-18.5 V | 14.5-18.5 V |
| Integrated NTC | Yes | Yes | Yes | Yes | Yes |
| Open-Drain Fault Output | Yes | Yes | Yes | Yes | Yes |
| Emitter Configuration | Open emitter | Open emitter | Open emitter | Open emitter | Open emitter |
Diferenciadores clave
- Higher current rating in the same CIPOS Mini footprint (frente a IKCM20F60GD)
- Production-reel ordering-code variant available for high-volume SMT-compatible through-hole assembly (frente a IKCM30F60GDXKMA1)
- Open-emitter configuration supports external shunt current sensing (frente a IKCM10H60GA)
Notas de diseño
Estimated: at 30 A continuous phase current and 600V switching, total power dissipation is approximately 25-35 W depending on switching frequency and power factor. The DIP 36x21D package requires an external heatsink sized to keep the case temperature below 100°C. Apply thermal compound (e.g., Shin-Etsu X-23-7772-4) at 1-2 mil bond-line thickness. For enclosed IP54 housings, derate to 20 A continuous to maintain case temperature below 85°C ambient.
Per Infineon CIPOS Mini design guidelines, keep the high-voltage DC-link copper pour (P and N terminals) at least 8 mm clearance from the low-voltage signal side (VCC, HIN/LIN, FLT, NTC). Maintain 600V reinforced isolation creepage per IPC-2221 between primary and secondary. Use a star-ground topology at the VSS pin; do not share ground returns between high-current motor phases and signal logic. Place 100 nF X7R ceramic bypass capacitors within 5 mm of VCC and VSS pins.
Bootstrap capacitor sizing: each high-side gate driver needs at least 1-4.7 uF C0G/X7R ceramic capacitor rated 25V minimum, charged through an external bootstrap diode (e.g., UF4007 or MBR0520). Insufficient bootstrap capacitance causes high-side underdrive at high duty cycles and shoot-through. Also, do not exceed 18.5V on VCC - overvoltage damages the gate oxide. Use a TVS (e.g., 18V SMAJ) on VCC for transient protection per the Infineon app note AN2011-08.
Route the HIN1/HIN2/HIN3 and LIN1/LIN2/LIN3 logic traces as 50-ohm controlled-impedance microstrip pairs to the MCU PWM outputs, with ground traces on either side. Keep these signal traces on the bottom layer and far from the high-voltage DC-link pour to minimize dv/dt-induced noise coupling. The FLT fault output is open-drain - require a 10 kohm pull-up to +3.3V MCU rail. Place the NTC voltage-divider resistor within 10 mm of the NTC pin to minimize noise pickup on the temperature sense.
Información de cumplimiento
RoHS compliant per Infineon product page. Industrial temperature grade; not AEC-Q100 qualified (choose Infineon automotive-grade IPMs for automotive use). DIP 36x21D package meets IPC-2221 reinforced isolation creepage for 600V.
