IKCM30F60GD - 600V 30A CIPOS Mini 3-Phase IPM | Infineon
Артикул: IKCM30F60GD ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $20.8 | $20,80 |
| 10 | $19.5 | $195,00 |
| 100 | $16.4 | $1.640,00 |
| 500 | $13.2 | $6.600,00 |
| 1.000 | $11.16 | $11.160,00 |
IKCM30F60GD Обзор
An intelligent power module (IPM) is a co-packaged power subsystem that integrates the power semiconductor switches (here, IGBTs plus freewheeling diodes), their gate drivers, and protection logic into one isolated module. Within the broader category hierarchy, the IKCM30F60GD is a power module > intelligent power module (IPM) > three-phase inverter IPM > gate-driver-integrated IGBT module > power management sub-system. This integration eliminates the need for engineers to design high-voltage gate-drive bootstrap circuits, level-shifters, and fault-detection networks, accelerating time-to-market.
Key features include a built-in NTC thermistor for temperature monitoring, an open-emitter configuration for flexible current sensing, Schmitt-triggered logic inputs with internal pull-down resistors and zener clamps, and 5 kohm internal input biasing that pre-biases the inputs at supply start-up. The module operates from a typical +15V control supply with an undervoltage lockout range of 14.5V to 18.5V, and provides fault feedback via an open-drain fault output pin. The DIP 36x21D footprint is a standardized CIPOS Mini outline that supports PCB-mount or socketed installation.
Typical applications include 3-phase brushless DC (BLDC) motor drives, permanent-magnet synchronous motor (PMSM) controllers, and AC induction motor drives for white goods, small industrial variable-frequency drives (VFDs), and ceiling fans. The integrated fault output simplifies coordination with an external microcontroller or DSP that supervises motor commutation and protection sequencing. Because the open emitter exposes the low-side IGBT emitters, the system can use external shunt resistors for precise current sensing and field-weakening control.
When designing with this module, ensure the bootstrap capacitors are sized to deliver sufficient charge to the high-side gate drivers during the worst-case PWM duty cycle, and place a low-ESR electrolytic or ceramic bulk capacitor directly at the rectified DC-link. The exposed thermal pad and DIP lead frame provide a thermal path that can be augmented with an external heatsink; refer to the manufacturer thermal-resistance curves for derating guidance. Always observe the minimum spacing required by the 600V isolation rating between the high-voltage and signal-side copper pours.
Аналоги без доработки для IKCM30F60GD — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
IKCM30F60GDXKMA1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
IKCM20F60GD
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
IKCM10H60GA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
IKCM50F60GD
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
IKCM30F60GD Максимальные параметры и электрические характеристики
| Product Family | CIPOS Mini Intelligent Power Module (IPM) |
| Топология | 3-phase IGBT inverter with open emitter |
| Collector-Emitter Voltage (Vces) | 600 V |
| Rated Output Current | 30 A |
| IGBT Technology | TRENCHSTOP |
| Control Supply Voltage (Vcc) | 14.5 V to 18.5 V (typical 15 V) |
| Undervoltage Lockout (UVLO) | Yes, with hysteresis |
| Built-in Protections | Overcurrent, Short-Circuit, Undervoltage Lockout, Thermal Shutdown |
| NTC Thermistor | Integrated, referenced to VSS |
| Input Logic | Schmitt-trigger with internal pull-down (approx. 5 kohm) and zener clamp |
| Fault Output | Open-drain fault feedback pin |
| Корпус | DIP 36x21D (24-PowerDIP Module, offset leads) |
| Тип монтажа | Through-hole (PCB mount or socketed) |
| Number of Terminals | 24 |
| Temperature Grade | Industrial |
| Surface Mount | No |
| Статус RoHS | Compliant |
Конфигурация выводов IKCM30F60GD
| Контакт 1 | P — DC-link positive (rectified + bus) |
| Контакт 2 | U — Phase U output to motor |
| Контакт 3 | V — Phase V output to motor |
| Контакт 4 | W — Phase W output to motor |
| Контакт 5 | N — DC-link negative (rectified - bus) |
| Контакт 6 | VCC — +15V control supply |
| Контакт 7 | VSS — Low-voltage signal ground |
| Контакт 8 | HIN1 — Logic input - high-side phase U |
| Контакт 9 | HIN2 — Logic input - high-side phase V |
| Контакт 10 | HIN3 — Logic input - high-side phase W |
| Контакт 11 | LIN1 — Logic input - low-side phase U |
| Контакт 12 | LIN2 — Logic input - low-side phase V |
| Контакт 13 | LIN3 — Logic input - low-side phase W |
| Контакт 14 | FLT — Open-drain fault output |
| Контакт 15 | NTC — Thermistor output to VSS |
| Контакт 16 | NC — Not connected (per datasheet) |
| Контакт 17 | NC — Not connected (per datasheet) |
| Контакт 18 | NC — Not connected (per datasheet) |
| Контакт 19 | NC — Not connected (per datasheet) |
| Контакт 20 | NC — Not connected (per datasheet) |
| Контакт 21 | NC — Not connected (per datasheet) |
| Контакт 22 | NC — Not connected (per datasheet) |
| Контакт 23 | NC — Not connected (per datasheet) |
| Контакт 24 | NC — Not connected (per datasheet) |
Типичное применение
IKCM30F60GD подходит для 6 применениеs: Home Appliance Motor Drives, Industrial Variable Frequency Drives (VFD), Ceiling Fan and HVAC Fans, Small Servo and Robotics Drives, Solar Inverter Auxiliary Stages, EV Charging Station Auxiliary Modules.
Home Appliance Motor Drives
The IKCM30F60GD is ideal for washing-machine drum motors, dishwasher pumps, and air-conditioner compressor inverters running from 200-240V AC mains. Its 600V Vces rating handles rectified 340V DC-link transients with margin, and the 30 A continuous current covers motors up to ~1.5 kW. The integrated UVLO and OCP simplify IEC 60335-1 safety compliance for white goods. Compared to discrete IGBT + driver solutions, the IPM reduces PCB area and BOM count, accelerating household appliance certification. Bootstrap-capacitor selection per Infineon app note AN2011-08 should be followed.
Рекомендуется
Industrial Variable Frequency Drives (VFD)
In low-power 3-phase VFDs for industrial automation, the IKCM30F60GD delivers the 30 A continuous rating needed for 0.75-1.5 kW AC induction or PMSM motors. The open-emitter configuration enables external shunt-based current sensing for field-oriented control loops, while the open-drain fault pin coordinates with supervisory PLCs. The 600V blocking voltage supports 480V class industrial bus with adequate margin. According to Infineon CIPOS Mini design guides, the IPM's integrated isolation eliminates optocoupler-based level-shifters, improving long-term reliability in factory-floor environments.
Рекомендуется
Ceiling Fan and HVAC Fans
The IKCM30F60GD is well suited to high-volume ceiling fan and HVAC fan BLDC motor drives where quiet operation and high efficiency are required. Sinusoidal FOC at 16-20 kHz PWM keeps the IKCM30F60GD inside its switching-loss envelope, while the integrated NTC thermistor enables overtemperature protection in enclosed fan housings. The 30 A current rating covers residential ceiling fans with significant overload margin. The DIP 36x21D package accepts through-hole mounting for robust mechanical assembly, important in mass-produced consumer appliances where PCB flex must be minimized.
Рекомендуется
Small Servo and Robotics Drives
For low-voltage 3-phase servo drives in robotics and CNC spindles below 1.5 kW, the IKCM30F60GD provides the integrated fault handling required for safety-critical motion control. The Schmitt-trigger inputs accept 3.3V logic directly from FPGA or MCU PWM outputs, and the 5 kohm internal pull-downs keep the IGBTs off during MCU reset for safe torque-off (STO) functionality. The exposed thermal pad supports direct heatsink attachment for high-duty-cycle robotic applications where continuous current is near 30 A. Per Infineon app note AN2014-09, follow creepage/clearance for the 600V reinforced isolation.
Рекомендуется
Solar Inverter Auxiliary Stages
In string-inverter auxiliary stages or DC-AC micro-inverters below 2 kW, the IKCM30F60GD handles the 600V DC bus with proper snubber design and provides grid-grade efficiency. The TRENCHSTOP IGBT technology minimizes switching losses at typical 16-20 kHz PWM frequencies, and the open-drain fault output enables rapid shutdown coordination with the inverter's grid-tie controller. The integrated UVLO at 14.5V protects the gate drivers during brownout conditions common in renewable installations. Place a Y-cap from rectified V+ to chassis ground per IEC 62109 for EMI.
Рекомендуется
EV Charging Station Auxiliary Modules
In 3-phase EV charging station auxiliary modules for cooling pumps, contactor drives, and bidirectional onboard charger stages, the IKCM30F60GD provides the 600V isolation and 30 A current needed for compact power stages. The CIPOS Mini DIP 36x21D package is well suited to IP54-rated enclosures with through-hole mounting for vibration resistance. The integrated OCP/SCP functions meet IEC 61851-1 safety requirements for EV supply equipment. The fault output enables CAN-coordinated fault reporting to the charging station's main controller.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для IKCM30F60GD — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | IKCM30F60GDXKMA1 | IKCM20F60GD | IKCM10H60GA | IKCM50F60GD |
|---|---|---|---|---|---|
| Package | DIP 36x21D (24-PowerDIP) | DIP 36x21D - same | DIP 36x21D - same | DIP 36x21D - same | DIP 36x21D - same |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Collector-Emitter Voltage (Vces) | 600 V | 600 V | 600 V | 600 V | 600 V |
| Rated Output Current | 30 A | 30 A | 20 A | 10 A | 50 A |
| IGBT Technology | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP | TRENCHSTOP |
| Control Supply (Vcc) | 14.5-18.5 V (15 V typ) | 14.5-18.5 V | 14.5-18.5 V | 14.5-18.5 V | 14.5-18.5 V |
| Integrated NTC | Yes | Yes | Yes | Yes | Yes |
| Open-Drain Fault Output | Yes | Yes | Yes | Yes | Yes |
| Emitter Configuration | Open emitter | Open emitter | Open emitter | Open emitter | Open emitter |
Ключевые отличия
- Higher current rating in the same CIPOS Mini footprint (против IKCM20F60GD)
- Production-reel ordering-code variant available for high-volume SMT-compatible through-hole assembly (против IKCM30F60GDXKMA1)
- Open-emitter configuration supports external shunt current sensing (против IKCM10H60GA)
Заметки по проектированию
Estimated: at 30 A continuous phase current and 600V switching, total power dissipation is approximately 25-35 W depending on switching frequency and power factor. The DIP 36x21D package requires an external heatsink sized to keep the case temperature below 100°C. Apply thermal compound (e.g., Shin-Etsu X-23-7772-4) at 1-2 mil bond-line thickness. For enclosed IP54 housings, derate to 20 A continuous to maintain case temperature below 85°C ambient.
Per Infineon CIPOS Mini design guidelines, keep the high-voltage DC-link copper pour (P and N terminals) at least 8 mm clearance from the low-voltage signal side (VCC, HIN/LIN, FLT, NTC). Maintain 600V reinforced isolation creepage per IPC-2221 between primary and secondary. Use a star-ground topology at the VSS pin; do not share ground returns between high-current motor phases and signal logic. Place 100 nF X7R ceramic bypass capacitors within 5 mm of VCC and VSS pins.
Bootstrap capacitor sizing: each high-side gate driver needs at least 1-4.7 uF C0G/X7R ceramic capacitor rated 25V minimum, charged through an external bootstrap diode (e.g., UF4007 or MBR0520). Insufficient bootstrap capacitance causes high-side underdrive at high duty cycles and shoot-through. Also, do not exceed 18.5V on VCC - overvoltage damages the gate oxide. Use a TVS (e.g., 18V SMAJ) on VCC for transient protection per the Infineon app note AN2011-08.
Route the HIN1/HIN2/HIN3 and LIN1/LIN2/LIN3 logic traces as 50-ohm controlled-impedance microstrip pairs to the MCU PWM outputs, with ground traces on either side. Keep these signal traces on the bottom layer and far from the high-voltage DC-link pour to minimize dv/dt-induced noise coupling. The FLT fault output is open-drain - require a 10 kohm pull-up to +3.3V MCU rail. Place the NTC voltage-divider resistor within 10 mm of the NTC pin to minimize noise pickup on the temperature sense.
Информация о соответствии
RoHS compliant per Infineon product page. Industrial temperature grade; not AEC-Q100 qualified (choose Infineon automotive-grade IPMs for automotive use). DIP 36x21D package meets IPC-2221 reinforced isolation creepage for 600V.
