Renesas Electronics

ISL83490IP - 3.3V Full-Duplex RS-485 Transceiver | Renesas

N.º de pieza: ISL83490IP ✓ Activo
3 V to 3.6 V Vdss 8-DIP, through hole Package
MOQ: 1 |

ISL83490IP Descripción general

Renesas Electronics ISL83490IP is a 3.3 V low-power RS-485/RS-422 interface transceiver with one driver and one receiver in an 8-pin DIP package. It operates from a 3 V to 3.6 V supply, supports full-duplex communication, and is designed for industrial and instrumentation links where low-voltage logic, compact size, and through-hole assembly are useful. The package is an 8-DIP measuring 0.300 inch, or 7.62 mm, across the lead span.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into differential bus voltages and converts differential bus signals back into receiver-compatible logic. The ISL83490IP combines both functions in one package, placing it within the hierarchy of interface transceivers, wired-communication ICs, and semiconductors. Separate transmit and receive paths support full-duplex systems, allowing a controller to transmit and receive data simultaneously over two differential pairs.

Key characteristics include a 3 V to 3.6 V supply range, one driver and one receiver, full-duplex operation, and support for both RS-485 and RS-422 communication protocols. Its 3.3 V supply operation suits modern embedded systems where 5 V interface devices may be undesirable. The through-hole 8-DIP construction also makes it practical for prototypes, industrial control equipment, legacy systems, and repair assemblies that favor socketed or leaded parts over fine-pitch surface-mount packages.

The ISL83490IP is intended for high-speed or slew-rate-limited differential communication. Controlled slew behavior helps limit unwanted transitions on the bus, while the low-power 3.3 V design can simplify interface design around low-voltage controllers. The transceiver architecture requires correct termination, biasing, grounding, and isolation practices to achieve reliable operation in multi-node RS-485 networks.

Typical uses include industrial serial controllers, factory automation equipment, building-control interfaces, test and measurement systems, motor-control diagnostics, and embedded communications modules. In each application, the IC can bridge a controller's UART or logic signals to a differential RS-485 or RS-422 bus, reducing wiring susceptibility to common-mode noise compared with single-ended signaling.

Designers should follow the pin-description table in the manufacturer datasheet when assigning PCB tracks and should preserve the specified supply decoupling arrangement. Cable length, topology, data rate, termination resistance, common-mode range, and grounding determine whether the complete communications link is reliable; successful transceiver selection alone does not guarantee standards-compliant operation.

This page combines interface classification, package and supply characteristics, application guidance, comparison parameters, and practical design notes to support evaluation of the ISL83490IP in low-voltage RS-485 and RS-422 systems.

Alternativas directas para ISL83490IP — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con ISL83490IP (mismo factor de forma y huella) — difiere en Duplex Mode, Maximum Data Rate, Package, Product Type, Transceiver Configuration.

Renesas Electronics
Duplex Mode: Half duplex
Maximum Data Rate: 10 Mbps
Package: 8-pin PDIP
Comparar con ISL83490IP →
Renesas Electronics
Maximum Data Rate: 250 kbps
Package: 8-pin PDIP (8-PDIP)
Transceiver Configuration: 1 transmitter and 1 receiver
Comparar con ISL83490IP →

SP3490EP-L

✅ Sustitución directa
📦 8-DIP (0.300 inch, 7.62 mm)
Driver and receiver implementation parameters differ; overall parameter match is estimated at 80%, subject to pin-by-pin electrical verification

📋 Alternativa de referencia (no en el catálogo)

ISL83490IP Especificaciones

Product Type RS-485/RS-422 transceiver IC
Number of Drivers 1 driver
Number of Receivers 1 receiver
Duplex Mode Full duplex
Supported Protocols RS-485 and RS-422
Supply Voltage Range 3 V to 3.6 V
Nominal Supply Voltage 3.3 V
Power Class Low power
Signal Profile High speed or slew-rate limited
Rango de temperatura de funcionamiento -40 °C to +85 °C
Package Type 8-DIP, through hole
Package Lead Span 0.300 inch (7.62 mm)
Tipo de montaje Through-hole
Shipping Container Tube
Operating Temperature Grade Industrial, -40 °C to +85 °C

Guía de configuración de pines de ISL83490IP 0.300 inch (7.62 mm)

Configuración de pines para ISL83490IP (encapsulado 0.300 inch (7.62 mm)). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 0.300 inch (7.62 mm) para ISL83490IP

No hay datos detallados de patillaje disponibles para ISL83490IP.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

ISL83490IP es adecuado para 6 aplicacións: Industrial Automation Serial Interfaces, Building Control and HVAC Networks, Test and Measurement Equipment, Embedded Data Acquisition Modules, Motor Control and Machinery Diagnostics, Legacy Communications and Field-Serviceable Boards.

🏭

Industrial Automation Serial Interfaces

The ISL83490IP fits industrial automation controllers that connect a low-voltage UART or control logic to an RS-485 or RS-422 field bus. Its 3 V to 3.6 V supply aligns with 3.3 V embedded logic, while the one-driver, one-receiver arrangement supports full-duplex data exchange. According to the manufacturer datasheet, the device operates from -40 °C to +85 °C. A typical implementation places the transceiver between the controller and protected bus connector, adding common-mode protection and the required termination or bias components. The 8-DIP through-hole package is also convenient for prototypes, socketed controller boards, and repairable industrial equipment. Designers should verify driver strength, receiver thresholds, isolation requirements, and grounding against their cable and topology.

🏭

Building Control and HVAC Networks

The ISL83490IP is appropriate for building-control and HVAC equipment that distributes commands over a balanced RS-485 network. Its 3.3 V operating range suits modern controller boards, and the full-duplex driver and receiver pair supports simultaneous command transmission and sensor-response reception. According to the manufacturer datasheet, the IC covers the -40 °C to +85 °C industrial temperature range and can operate in high-speed or slew-rate-limited applications. Place it near the controller or wiring interface, provide local supply decoupling, and use protection suited to the building's cable environment. Because building networks can experience ground-potential differences and surge events, external protection and an isolated interface may be needed even when the transceiver itself meets the basic RS-485 or RS-422 requirements.

🔧

Test and Measurement Equipment

The ISL83490IP can serve as the communications interface in test and measurement equipment that must exchange commands and results over a reliable differential bus. Its full-duplex configuration permits continuous two-way control, while operation from 3 V to 3.6 V supports compact instrumentation built around low-voltage logic. According to the manufacturer datasheet, the device provides one driver, one receiver, and RS-485/RS-422 protocol support. In an instrument, the transceiver can connect a controller to a rear-panel connector or multipoint bus. Keep the analog and digital ground strategy defined by the complete instrument, verify common-mode limits before installation, and add external surge protection for cables that leave the enclosure. The 8-DIP package also simplifies through-hole prototypes and field-serviceable assemblies.

🧩

Embedded Data Acquisition Modules

The ISL83490IP is useful in embedded data-acquisition modules that need to distribute sensor readings or configuration commands over a multi-drop RS-485 network. Its low 3.3 V supply requirement simplifies interface design around compact controllers, while the transceiver's driver and receiver support a single-channel full-duplex arrangement. According to the manufacturer datasheet, the operating-temperature range is -40 °C to +85 °C. A practical module can use the IC between the controller UART and a protected terminal block, with biasing and termination placed according to the network topology. The system's cable length, node count, and data rate must be considered because they determine the usable communications margin. The through-hole 8-DIP package is especially practical for prototype modules and designs assembled with sockets or leaded components.

⚡

Motor Control and Machinery Diagnostics

The ISL83490IP fits motor controllers and machinery-diagnostic equipment that exchange commands, status, and fault data over a differential bus. The 3 V to 3.6 V operation is compatible with modern control electronics, and the full-duplex driver and receiver allow a controller to issue commands while receiving diagnostic feedback. According to the manufacturer datasheet, the transceiver is rated from -40 °C to +85 °C, making it appropriate for many industrial environments. In a motor-control design, install the interface near the controller connector and isolate noisy motor-drive circuitry from sensitive communications routing. External protection may be necessary when the bus cable experiences motor transients or large ground-potential differences. Verify signal timing and bus loading against the complete motor network rather than relying on transceiver selection alone.

🔧

Legacy Communications and Field-Serviceable Boards

The ISL83490IP is a practical choice for legacy communication boards, conversion equipment, and field-serviceable products that favor a leaded package. According to the manufacturer datasheet, it is an 8-DIP through-hole device with a 0.300-inch, or 7.62 mm, lead span and a -40 °C to +85 °C operating range. Its 3.3 V supply suits modern controller logic without requiring a 5 V transceiver. Through-hole construction simplifies socketed assembly, point-to-point wiring in simple equipment, and repair workflows that favor replaceable components. The full-duplex RS-485/RS-422 function can support a modern controller communicating with older differential equipment, although logic levels, timing, and termination must be reconciled. Board layout should follow the manufacturer pin table and preserve the recommended decoupling arrangement.

What is the ISL83490IP?
The ISL83490IP is a 3.3 V low-power RS-485/RS-422 transceiver containing one driver and one receiver for full-duplex differential communication. According to the manufacturer datasheet, it operates from 3 V to 3.6 V and is offered in an 8-DIP through-hole package with a 0.300-inch, or 7.62 mm, lead span. It is suitable for low-voltage embedded controllers, industrial controls, test systems, and other equipment that uses differential balanced-line communications.
What is the operating voltage of ISL83490IP?
The ISL83490IP operates from 3 V to 3.6 V. According to the manufacturer datasheet, its nominal operating supply is 3.3 V, making it appropriate for systems whose digital control logic operates at that voltage. The device combines the supply requirement with one driver, one receiver, and full-duplex operation. System designers should also observe the datasheet's input thresholds, output levels, and recommended decoupling network when connecting the transceiver to a low-voltage controller.
Where can I download the ISL83490IP datasheet PDF?
The ISL83490IP datasheet PDF can be reached through the manufacturer-document link listed on this page or through the Intersil datasheet result identified as ISL83490IP Datasheet (PDF). The document covers the 3.3 V low-power RS-485/RS-422 transceiver, including its 8-DIP pin assignments and operating limits. Use the pin-description table in that document when laying out the board, especially because lead numbering and signal names must follow the package drawing exactly.
Where can I find the ISL83490IP pinout?
The ISL83490IP pinout is documented in the manufacturer datasheet's 8-DIP pin-description diagram and accompanying pin table. The component is an 8-pin through-hole device with one driver and one receiver for full-duplex RS-485/RS-422 operation. Assign tracks by the numbered package pins rather than by visual proximity. A separate public pin table was not reproduced here, so use the manufacturer drawing as the authoritative source for the driver, receiver, enable, ground, and supply connections.
Is ISL83490IP suitable for RS-485 industrial automation?
The ISL83490IP is suitable for RS-485 industrial automation interfaces when the design operates within its stated electrical limits. According to the manufacturer datasheet, the IC supports RS-485 and RS-422, operates from 3 V to 3.6 V, and is rated from -40 °C to +85 °C. Industrial suitability also depends on bus protection, grounding, surge handling, cable length, data rate, and compliance with the complete system's interface requirements.
What is the difference between RS-485 and RS-422 operation with ISL83490IP?
RS-485 and RS-422 both use differential signaling, but they differ in bus topology and termination expectations. According to the manufacturer datasheet, the ISL83490IP supports both protocols with separate driver and receiver paths. RS-422 is commonly used for point-to-point links, while RS-485 commonly supports multiple nodes on a bus. Exact termination, biasing, grounding, and topology must follow the selected system standard and the device's recommended application circuit.
IS ISL83490IP full duplex or half duplex?
The ISL83490IP is a full-duplex transceiver with one driver and one receiver. According to the manufacturer datasheet, this arrangement provides separate transmit and receive functions rather than sharing a single multidirectional bus. Full-duplex use generally requires two differential signal pairs and appropriate termination on each pair. The 8-DIP package also supports the device's low-power 3.3 V operation across the -40 °C to +85 °C temperature range.
What are the key specifications of ISL83490IP that engineers should know?
The ISL83490IP combines one driver, one receiver, full-duplex operation, RS-485/RS-422 support, and a 3 V to 3.6 V supply in an 8-DIP package. According to the manufacturer datasheet, its operating-temperature range is -40 °C to +85 °C, and the package lead span is 0.300 inch, or 7.62 mm. The device is described as low power and available for high-speed or slew-rate-limited signaling, making it relevant to 3.3 V industrial and embedded interfaces.
IS ISL83490IP the same as SP3490EP-L?
The ISL83490IP and SP3490EP-L are candidate interface substitutes, but they are not identical product functions until every electrical and timing parameter is checked. The cross-reference comparison identifies SP3490EP-L against ISL83490IP, and both are associated with an 8-pin through-hole interface implementation. According to the manufacturer datasheets, engineers should compare supply range, receiver thresholds, driver output, data rate, slew behavior, enable logic, and pin names before treating the candidate as a drop-in replacement.
When should I choose ISL83490IP over a drop-in alternative?
Choose the ISL83490IP when the design needs a 3.3 V, low-power, full-duplex RS-485/RS-422 interface in an 8-DIP package. According to the manufacturer datasheet, it operates from 3 V to 3.6 V over -40 °C to +85 °C. Select an alternative only after confirming that its driver strength, receiver thresholds, timing, enable polarity, supply limits, and exact pin assignments meet the system requirements. The leaded package can also be preferable for prototypes and socket-based legacy equipment.
Can SP3490EP-L replace ISL83490IP?
SP3490EP-L is a candidate replacement for the ISL83490IP, but final approval requires a pin-by-pin and parameter-by-parameter comparison. According to the manufacturer datasheets, both devices are associated with 8-pin through-hole RS-485 interface implementations. Verify the 3.3 V supply compatibility, full-duplex signal arrangement, driver and receiver performance, enable behavior, temperature range, and lead orientation before production use. Request the current availability and quotation through the Request a Quote form on this page.
What is the best drop-in replacement for ISL83490IP?
SP3490EP-L is the identified candidate for evaluating as an ISL83490IP drop-in replacement. According to the manufacturer datasheets, the relevant match points are the 8-pin through-hole format and differential transceiver function. A production substitution still requires verification of supply voltage, driver and receiver thresholds, data rate, slew rate, enable logic, and every physical pin. Use the Request a Quote form on this page for current availability and a replacement-review quotation.
Where to buy ISL83490IP online?
The ISL83490IP can be requested through the Request a Quote form on this page for current commercial availability, packaging, and lead time. According to the manufacturer datasheet, the part is an 8-DIP, full-duplex RS-485/RS-422 transceiver intended for a 3 V to 3.6 V supply. Include the required quantity, tube packaging preference, and delivery region in the request so the commercial response can reflect the complete procurement requirement.
What is the price of ISL83490IP?
Current commercial pricing for the ISL83490IP is obtained through the Request a Quote form on this page rather than from a static product-page value. According to the manufacturer datasheet, the component is specified as a 3.3 V low-power full-duplex RS-485/RS-422 transceiver in an 8-DIP package. The quotation request should state quantity, desired delivery terms, and whether tube packaging is required for an accurate sourcing response.
What is the lead time and stock status of ISL83490IP?
Current stock and lead time for the ISL83490IP should be confirmed through the Request a Quote form on this page. According to the manufacturer datasheet, the standard commercial configuration is an 8-DIP, through-hole package supplied in a tube for a -40 °C to +85 °C operating range. Provide the required quantity and target delivery date so the response can address availability, production scheduling, and shipment requirements for the exact ISL83490IP order.
What design considerations apply to an ISL83490IP RS-485 board?
Use the ISL83490IP's recommended decoupling and pin assignments exactly as shown in the manufacturer datasheet. According to the datasheet, the IC is a 3.3 V full-duplex RS-485/RS-422 transceiver in an 8-DIP package. Keep differential traces appropriately routed, connect grounds according to the application circuit, install the intended termination and protection, and account for common-mode voltage and surge requirements. These board-level measures are as important as transceiver selection for a reliable communications link.

Datos de referencia de ingeniería para ISL83490IP — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the ISL83490IP when a design requires a 3.3 V full-duplex RS-485/RS-422 transceiver in an 8-DIP through-hole package. It is particularly useful for prototypes, socketed assemblies, repairable industrial equipment, and controllers with 3.3 V logic. SP3490EP-L is the candidate to evaluate when seeking an alternative 8-DIP interface, but substitution should proceed only after comparing supply range, receiver thresholds, driver output, data rate, slew behavior, enable logic, and every pin assignment. If a surface-mount footprint, galvanic isolation, lower power consumption, or a different bus topology is required, the ISL83490IP should not be selected merely because its protocol label matches. The final decision must reflect the complete cable, protection, grounding, temperature, and sourcing requirements of the communications link.

Comparación con alternativas

Parámetro Este producto SP3490EP-L
Brand Renesas Electronics Diodes Incorporated
Package 8-DIP (0.300 inch, 7.62 mm) 8-DIP (0.300 inch, 7.62 mm)
Mounting Type Through hole Through hole

Diferenciadores clave

  • Low-voltage operation matches modern 3.3 V controller logic (frente a SP3490EP-L)
  • Full-duplex differential interface in a through-hole package (frente a SP3490EP-L)
  • Supports both RS-485 and RS-422 interfaces (frente a SP3490EP-L)

Notas de diseño

Use the manufacturer datasheet's 8-DIP pin-description table as the authoritative assignment for supply, ground, enable, driver, and receiver signals. Place the recommended input and output bypass capacitors adjacent to their associated pins and keep their ground returns short. For a differential bus, route the driver and receiver traces as a closely matched pair, minimize stubs, and keep switching or high-current return paths away from the communications nodes. The 7.62 mm lead pitch requires a compatible 0.300-inch DIP footprint rather than a narrow-pitch SOIC land pattern.

Do not treat the RS-485 or RS-422 protocol name as a guarantee that any wiring arrangement will work. Match termination to the cable and topology, install biasing only where the network design requires it, and account for common-mode voltage, cable length, node count, and data rate. Verify that the chosen receiver thresholds satisfy the intended noise margin. According to the manufacturer datasheet, the ISL83490IP supports both protocols, but the external network and protection components determine actual link reliability.

Use controlled slew behavior to reduce reflected transitions and radiated noise, especially on long or poorly terminated cables. Place optional protection devices near the external connector so surge or electrostatic-discharge energy is clamped before reaching the transceiver. Provide a defined ground strategy for interfaces that bridge separated equipment; if large ground-potential differences are possible, evaluate galvanic isolation rather than relying on the IC alone. After layout changes, verify both radiated emissions and susceptibility in the complete enclosure and cable configuration.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The -40 °C to +85 °C operating range is not equivalent to AEC-Q100 qualification. No additional RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were established from the referenced manufacturer documents.

Datos verificados el: 2026-11-15 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

ISL83490IP datasheet ISL83490IP pinout ISL83490IP datasheet pdf ISL83490IP specifications Renesas ISL83490IP ISL83490IP 3.3V transceiver ISL83490IP 8-DIP package ISL83490IP RS-485 application ISL83490IP vs SP3490EP-L ISL83490IP replacement ISL83490IP cross reference ISL83490IP price ISL83490IP stock ISL83490IP footprint ISL83490IP equivalent

Componentes & términos relacionados

Renesas Electronics ISL83490IP SP3490EP-L RS-485 RS-422 differential transceiver interface transceiver wired communications IC semiconductor full duplex one driver one receiver 3.3 V transceiver low-power IC 8-DIP package DIP package family through-hole package surface-mount alternative industrial automation building control test and measurement motor diagnostics common-mode voltage slew rate RS-485 bus termination
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ