KSZ8081MLXCA - 3.3V 10/100 Ethernet PHY | Microchip Technology
N.º de pieza: KSZ8081MLXCA ✓ ActivoKSZ8081MLXCA Descripción general
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into electrical signals suitable for twisted-pair networking and converts incoming signals back into digital data. In the network hierarchy, the KSZ8081 belongs to Ethernet interface ICs, where it provides the physical-layer function between a media-access controller and a network cable.
The KSZ8081 supports both 10BASE-T and 100BASE-TX operation from one integrated PHY. Its single-supply 3.3 V architecture reduces the number of external supply rails required in compact equipment, while the 48-LQFP package provides 48 electrical and thermal-pad-related package positions for a conventional surface-mount PCB layout. The device is intended for 10/100 Ethernet rather than gigabit Ethernet.
Microchip describes the KSZ8081 as a highly integrated PHY that reduces board cost and simplifies implementation of 10BASE-T/100BASE-TX network ports. This integration is valuable in industrial controllers, embedded systems, access equipment, and communication products where an Ethernet connection must coexist with a digital host controller over a compact board area.
Typical uses include industrial Ethernet control systems, embedded gateways, serial-to-Ethernet equipment, network-connected test instruments, building-control interfaces, and compact communication modules. The PHY can be paired with a suitable Ethernet media-access controller, and its CAT-5 UTP compatibility supports conventional copper Ethernet infrastructure.
PCB design should follow the pin-description and layout guidance in the manufacturer datasheet, particularly for the differential TX and RX pairs, crystal or clock circuitry, decoupling, and the exposed thermal pad. Maintain controlled-impedance routing for the 100BASE-TX differential pairs and provide low-impedance power and ground planes around the transceiver.
This product page combines the manufacturer’s PHY description with package, voltage, temperature, and cross-reference details, then organizes the engineering trade-offs around PCB layout, network compatibility, documentation, and genuine same-footprint alternatives. These practical considerations help shorten component-selection and hardware-validation work.
Alternativas directas para KSZ8081MLXCA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
KSZ8081MLIA
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
KSZ8081MLXCC
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
KSZ8081MLXCA-TR
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
KSZ8081MLICA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
KSZ8081MLCC
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
KSZ8081MLXCA Especificaciones
| Device Type | 10BASE-T/100BASE-TX Ethernet physical-layer transceiver |
| Supported Ethernet Speeds | 10 Mbps and 100 Mbps |
| Data Channels | 1 channel |
| Supply Type | Single supply |
| Operating Voltage Range | 3.135 V to 3.465 V |
| Nominal Supply Voltage | 3.3 V |
| Cable Compatibility | CAT-5 unshielded twisted-pair cable |
| Encapsulado | 48-LQFP, 7 mm × 7 mm |
| Recuento de pines | 48 pins |
| Tipo de montaje | Surface-mount |
| Minimum Operating Temperature | 0 °C |
| Maximum Operating Temperature | 70 °C |
| Ethernet Interface Class | Full Ethernet |
| Rango de temperatura de funcionamiento | 0 °C to 70 °C |
| Estado RoHS | unknown |
Guía de configuración de pines de KSZ8081MLXCA 48-lqfp, 7 mm × 7 mm
Configuración de pines para KSZ8081MLXCA (encapsulado 48-lqfp, 7 mm × 7 mm). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para KSZ8081MLXCA.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
KSZ8081MLXCA es adecuado para 6 aplicacións: Industrial Ethernet Control Equipment, Embedded Network Gateways, Serial-to-Ethernet Communication Modules, Networked Test and Measurement Instruments, Building-Control and Automation Interfaces, Compact Communication and Access Equipment.
Industrial Ethernet Control Equipment
The KSZ8081MLXCA suits compact industrial controllers that require a 10/100 Ethernet physical layer without a separate multi-rail PHY design. Its 3.135 V to 3.465 V operating range is centered on a 3.3 V system supply, while the 100BASE-TX capability supports faster traffic than 10BASE-T on suitable CAT-5 UTP networks. Place the PHY beside the host media-access controller and route its differential TX and RX pairs as controlled-impedance nets. The principal design trade-off is its 0 °C to 70 °C rating, which suits controlled indoor equipment but requires an extended-temperature alternative for harsher enclosures.
Recomendado
Embedded Network Gateways
The KSZ8081MLXCA provides the copper-network interface in an embedded gateway that bridges a local processor or microcontroller to a 10/100 Ethernet network. Its single-supply 3.3 V operation reduces power-tree complexity, and the 48-LQFP package supports a conventional surface-mount layout with direct access to the Ethernet differential pairs. The PHY must be paired with a compatible media-access controller and an appropriate clock source. Compared with adding a discrete magnetics-based Ethernet interface, the integrated PHY can reduce board area, although designers must still implement the required external network components and controlled-impedance routing.
Recomendado
Serial-to-Ethernet Communication Modules
A serial-to-Ethernet module can use the KSZ8081MLXCA to add a 10/100 copper-network port to an embedded serial platform. The PHY supports both 10BASE-T and 100BASE-TX, allowing the host controller to negotiate the appropriate rate on the connected network. The 3.3 V single-supply architecture is useful in compact modules where supply rails and board area are constrained. Designers should reserve the manufacturer-recommended clock, decoupling, and magnetics support networks and route the differential pairs away from switching nodes and high-current paths. The part’s 0 °C to 70 °C range limits its use in unheated outdoor enclosures.
Recomendado
Networked Test and Measurement Instruments
The KSZ8081MLXCA can provide the 10/100 Ethernet link for laboratory instruments that exchange commands and measurement data with a host computer. A 100BASE-TX-capable PHY supports responsive transfers over switched office networks, while 10BASE-T compatibility allows operation on older infrastructure. The 48-LQFP package is practical for multilayer PCBs where the PHY can be placed near the RJ45 connector and network magnetics to shorten sensitive differential traces. Keep the TX and RX pairs impedance controlled, provide a clean 3.3 V supply, and isolate analog or high-speed measurement circuitry from the Ethernet section to avoid coupling.
Recomendado
Building-Control and Automation Interfaces
The KSZ8081MLXCA is appropriate for building-control modules that need reliable 10/100 Ethernet communication within an indoor automation network. Its integrated PHY supports CAT-5 UTP cabling and a single 3.3 V supply, simplifying integration with embedded controllers and communications processors. The commercial temperature range of 0 °C to 70 °C covers many conditioned rooms but may not cover unheated equipment cabinets. Select the extended-temperature KSZ8081MLIA when enclosure temperatures can fall below 0 °C. PCB implementation should follow the manufacturer’s differential-pair and power-layout guidance to maintain reliable network performance.
Recomendado
Compact Communication and Access Equipment
The KSZ8081MLXCA can add a standard copper-Ethernet port to compact access equipment such as protocol converters, terminal servers, and network supervisory modules. Supporting both 10BASE-T and 100BASE-TX gives the host controller link flexibility across modern and legacy networks. The single-supply 3.3 V design and 48-LQFP package allow the PHY to be placed near the connector and isolation components while keeping the layout manageable. Designers should verify the complete pin assignment, clock requirements, external magnetics network, and impedance-controlled pair geometry from the manufacturer datasheet before releasing the PCB.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para KSZ8081MLXCA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | KSZ8081MLIA | KSZ8081MLXCC | KSZ8081MLXCA-TR | KSZ8081MLICA | KSZ8081MLCC |
|---|---|---|---|---|---|---|
| Package | 48-LQFP, 7 mm × 7 mm | 48-LQFP | 48-LQFP | 48-LQFP | 48-LQFP | 48-LQFP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Device Type | 10BASE-T/100BASE-TX Ethernet PHY | 10BASE-T/100BASE-TX Ethernet PHY | KSZ8081 Ethernet PHY family | 10BASE-T/100BASE-TX Ethernet PHY | KSZ8081 Ethernet PHY family | KSZ8081 Ethernet PHY family |
| Order Presentation | Standard KSZ8081MLXCA ordering code | Extended-temperature ordering code | Alternate ordering code | Tape-and-reel ordering code | Extended-temperature ordering code | Alternate ordering code |
Diferenciadores clave
- Commercial-temperature ordering option (frente a KSZ8081MLIA)
- Single-supply 10/100 Ethernet integration (frente a KSZ8081MLXCA-TR)
- Direct use in 48-LQFP network designs (frente a KSZ8081MLXCC)
Notas de diseño
Route the Ethernet TX and RX differential pairs as controlled-impedance traces referenced to a continuous ground plane. Match differential impedance and pair length according to the manufacturer’s PCB-layout guidance, and keep the PHY close to the external isolation and magnetics components. Avoid placing switching-power nodes, high-speed clocks, or other high-current paths beneath or immediately beside the differential pairs.
Use the datasheet-recommended supply decoupling and placement arrangement. The PHY operates in a narrow 3.135 V to 3.465 V range around 3.3 V, so the local rail must remain within limits across temperature, tolerance, and load transients. Place bypass capacitors at the appropriate supply pins with short ground returns, and avoid sharing high-current return paths between the PHY and noisy digital or power-conversion circuitry.
Do not select an alternative from the base family name alone. Confirm the exact ordering suffix, temperature range, package drawing, pin assignments, clock requirements, and Ethernet reference circuitry against the manufacturer datasheet. The KSZ8081MLIA extends the temperature range from 0 °C–70 °C to -40 °C–85 °C, while KSZ8081MLXCA-TR changes the order presentation. Both distinctions affect sourcing or mechanical planning.
Pay particular attention to clock-source implementation and startup behavior because the PHY must communicate reliably with the host media-access controller. Follow the manufacturer’s reference schematic for crystal, oscillator, termination, and bias components, and maintain the specified trace geometry. Validate startup with the intended host controller because seemingly interchangeable family variants can differ in clock or reset implementation even when they use the same package.
Información de cumplimiento
Compliance declarations were not identified in the product documentation reviewed for this ordering code. The Ethernet PHY is not an automotive-qualified ordering variant on the basis of the available information.